PPO-based acid–base polymer blend membranes for direct methanol fuel cells

New acid–base polymer blend membranes for direct methanol fuel cells (DMFC) have been designed using a very accessible commercial polymer, poly(2,6-dimethyl-1,4-phenylene oxide) (PPO). The preparation begins with the sulfonation and bromination of PPO to sulfonated PPO (SPPO) and bromomethylated PPO (BrPPO), respectively. Blend membranes are formed by mixing n-propylamine(PrNH₂)-neutralized SPPO and PrNH₂-aminated BrPPO solutions in N-methyl-2-pyrrolidone (NMP), and casting the mixed solution on glass petri dishes followed by acidification with aqueous hydrochloric acid. The compatibility between the acid and base components of the blend is assured by using acidic and basic polymers deriving from the same parent polymer (PPO). Ionic crosslinking is established between the sulfonic groups of SPPO and the amine groups of aminated BrPPO. The ionic crosslinking strengthens the membrane dimensional stability by reducing water uptake and membrane swelling up to temperatures as high as 80 °C. The membranes fabricated as such display good resistance to methanol crossover amidst some, but acceptable loss of proton conductivity. The characteristic factor (i.e. the ratio of proton conductivity to methanol permeability) increases noticeably with the BrPPO content, with the sample containing 30 wt.% BrPPO showing a 16-fold improvement over Nafion 117. The mechanical properties and oxidative stability of the blend membranes also satisfy the requirements for fuel cell assembly and operation.     

Sulfonated poly(meta‐phenylene isophthalamide)s as proton exchange membranes

Random and block sulfonated poly(meta‐phenylene isopthalamide)s as proton exchange membranes were synthesized through the Higashi‐Yamazaki phosphorylation method. Polymers with different degrees of sulfonation from 40 to 100 mol percent were prepared by adjusting the molar feed ratio of 5‐sulfoisophthalic acid sodium salt (SIPA) and isophthalic acid (IPA) in the reaction with meta‐phenylene diamine. Creasable polymer films were obtained by casting DMSO polymer solutions and the membrane films could be exchanged to the proton form in strong acid. ¹H NMR spectroscopy and titration confirmed the degree of sulfonation. Thermogravimetric analysis demonstrated good thermal stabilities with 5% weight loss greater than 380 °C. The copolymers with low degrees of sulfonation (DS = 40 mol %) exhibited low water uptake (water uptake < 17 wt %) at room temperature. A segmented multiblock copolymer prepared by preforming a sulfonated block showed lower water uptake at high temperatures than the random polymer with the same DS of 40 mol % and displayed stability in water up to 80 °C. Both random and block copolymers showed higher proton conductivities at high temperature than that of Nafion‐117 under 95% relative humidity. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2582–2592     

Synthesis, characterization and thermoreversible behaviours of poly(dimethyl siloxane)/poly(N-isopropyl acrylamide) semi-interpenetrating networks

Simultaneous and sequential poly(N-isopropyl acrylamide) (PNIPAAm)/poly(dimethyl siloxane) (PDMS) semi-interpenetrating polymer networks (IPNs) with different linear PDMS contents were prepared by free radical polymerization method. Their phase morphologies have been characterized by FTIR, DSC and SEM. The simultaneous semi-IPNs exhibited phase transition temperatures (T_pt) shifted higher temperature from glass transition temperatures (T_g) of their respective homopolymers, suggesting a heterophase morphology and only physical entanglement between the PNIPAAm network and linear PDMS with high molecular weight (Mn≈9000 g/mol). For sequential semi-IPNs, the shift of T_pts towards lower temperature suggested that the chemical interaction between the constituents of the IPNs increased with increasing PDMS content in the network. In addition, these semi-IPNs were characterized for their thermo-sensitive behaviour by equilibrium swelling studies. The results showed that incorporation of hydrophobic PDMS polymer into the thermo- and pH-sensitive PNIPAAm and P(NIPAAm-co-IA) (itaconic acid) hydrogels by semi-IPN formation decreased swelling degrees of IPNs without affecting their LCSTs whereas addition of acrylated PDMS (Tegomer V-Si 2250) as crosslinker instead of N,N^′-methylenebisacrylamide (BIS) into the structures of these hydrogels changed their LCSTs along with their swelling degrees.     

Macromolecular dynamics of sulfonated poly(styrene-b-ethylene-ran-butylene-b-styrene) block copolymers by broadband dielectric spectroscopy

Macromolecular dynamics of sulfonated poly(styrene-b-ethylene-ran-butylene-b-styrene) (sSEBS) triblock copolymers were investigated using broadband dielectric spectroscopy (BDS). Two main relaxations corresponding to the glass transitions in the EB and S block phases were identified and their temperature dependences were VFT-like. T_g for the S block phase shifted to higher temperature due to restrictions on chain mobility caused by hydrogen bonded SO₃H groups. While the EB block phase T_g appeared to remain constant with degree of sulfonation in DMA experiments, it shifted somewhat upward in BDS spectra. A low temperature relaxation beneath the glass transition of the EB block phase was attributed to short range chain motions. The Kramers–Krönig integral transformation was used to calculate conductivity-free loss permittivity spectra from real permittivity spectra to enhance true relaxation peaks. A loss permittivity peak tentatively assigned to relaxation of internal S-EB interfacial polarization was seen at temperatures above the S block phase glass transition, and the temperature dependence of this relaxation was VFT-like. The fragilities of the EB and S block domains in sulfonated SEBS decreased after sulfonation. The temperature dependence of the dc conduction contribution to sSEBS loss spectra also followed VFT-like behavior and S block segmental relaxation time correlated well with conductivity according to the fractional Debye–Stokes–Einstein equation.     

Sulfonated poly(arylene thioether phosphine oxide)s copolymers for proton exchange membrane fuel cells

High molecular weight sulfonated poly(arylene thioether phosphine oxide)s (sPATPO) with various sulfonation degrees were prepared directly by aromatic nucleophilic polycondensation of 4,4′-thiobisbenzenethiol with sulfonated bis(4-fluorophenyl) phenyl phosphine oxide and bis(4-fluorophenyl) phenyl phosphine oxide. sPATPO in the acid form with sulfonation degrees of 60–100% exhibits a glass transition temperature higher than 230 °C and a 5% weight loss temperature above 400 °C, indicating high thermal stability. sPATPO with a high sulfonation degree shows high proton conductivity and good resistance to swelling as well. For instance, sPATPO-70 displays the conductivity of 0.0783 S/cm and a swelling ratio of 11.6% at 90 °C. TEM micrographs showed that sPATPO membranes with a high sulfonation degree could form continuous ion channels, which are favorable for improving the proton conductivity but harmful to remaining the mechanical property. The membranes are expected to show good performances in fuel cell applications.     

Synthesis of sulfonated poly(diphenylacetylene)s with high CO2 permselectivity

High‐molecular‐weight poly[1‐phenyl‐2‐(4‐t‐butylphenyl)acetylene], poly[1‐phenyl‐2‐(4‐trimethylsilylphenyl) acetylene], and their copolymers were synthesized by the polymerization with TaCl₅–n‐Bu₄Sn. The obtained polymers were sulfonated by using acetyl sulfate to give sulfonated poly(diphenylacetylene)s with different degrees of substitution. The degrees of sulfonation of poly[1‐phenyl‐2‐(4‐t‐butylphenyl)acetylene] and copolymers were in the range of 0.57–0.85. When poly[1‐phenyl‐2‐(4‐trimethylsilylphenyl)acetylene] was sulfonated, the sulfonated poly(diphenylacetylene) with the highest degree of sulfonation was obtained among all the polymers in this study. Its degree of sulfonation was 1.55. All the sulfonated polymers exhibited high CO₂ permselectivity, and their CO₂/N₂ separation factor were over 31. The sulfonated poly(diphenylacetylene) with the highest degree of sulfonation showed the highest CO₂/N₂ separation factor of 75. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6463–6471, 2009     

Structural investigation of polystyrene grafted and sulfonated poly(tetrafluoroethylene) membranes

Structural investigation of polystyrene grafted and sulfonated poly(tetrafluoroethylene) (PTFE) membranes prepared by radiation-induced grafting of styrene onto commercial PTFE films and subsequent sulfonation was carried out by differential scanning calorimetry and X-ray diffraction. The effect of the structural changes taking place in the membranes during the preparation procedure (grafting and sulfonation) and the variation of the degree of grafting on melting temperature (T_m), glass transition temperature (T_g), heat of melting (ΔH_m), and degree of crystallinity was studied. The melting temperature (T_m) was found to be independent of the degree of grafting unlike glass transition temperature (T_g), which was found to be a function of the degree of grafting. Moreover, the degree of crystallinity of the membranes was found to decrease with the increase in the degree of grafting. The results of this work suggest that grafting takes place in the entire amorphous region without any significant disruption in the crystalline structure of PTFE film and the decrease in the degree of crystallinity is mainly attributed to the dilution effect.     

Synthesis and characterization of thermally stable sulfonated polybenzimidazoles obtained from 3,3′‐disulfonyl‐4,4′‐dicarboxyldiphenylsulfone

A novel sulfonated aromatic diacid, 3,3′‐disulfonyl‐4,4′‐dicarboxyldiphenylsulfone (DSDCDPS), was successfully synthesized from 4,4′‐dimethyldiphenylsulfone by sulfonation and further oxidation. A series of sulfonated polybenzimidazoles (sPBI‐SS) with various sulfonation degrees was prepared from DSDCDPS, 4,4′‐sulfonyldibenzoic acid and 3,3′‐diaminobenzidine by solution copolycondensation in poly(phosphoric acid). The chemical structure of the resulting sPBI‐SS was confirmed by FTIR and ¹H NMR. The DSDCDPS‐based sPBI‐SS with the number‐average molecular weights of 32,000–55,000 were easy to dissolve in polar aprotic solvents such as DMF, DMSO, and DMAc, and could be cast into transparent, tough, and flexible membranes. The membranes presented good thermal stabilities (5% weight loss temperatures higher than 430 °C), and the thermal degradation activation energies of the sulfonic group of sPBI‐SS40 evaluated under N₂ by both Ozawa and Kissinger methods were 266.06 and 264.79 kJ/mol, respectively. The membranes also exhibited high storage moduli, glass transition temperatures (above 238 °C) and tensile strengths (～80 MPa), in addition to water uptakes (22.3–25.2%) and low swelling degrees (<14.0%). © 2005 Wiley Periodicals, Inc. J Polym Sci A: Polym Chem 43: 4363–4372, 2005     

Rheological properties of poly(2,6-dimethylphenylene oxide)—polystyrene blends

The viscoelastic (VE) response of freeze-dried blends of polystyrene (PS) and poly-(2,6-dimethyl phenylene oxide) (PPO) has been studied as a function of composition, frequency, and temperature to examine the degree of rheological compatibility. When blended together, the relaxation processes of both molecular species exhibit the same temperature dependence. However, the temperature dependence of the VE response is a function of composition. It is shown that this behavior can be predicted from the measured glass transition temperatures by assuming the additivity of the free volumes of the components. The properties of the blends are compared at equal free volumes. The effective segmental friction factor is found to be independent of composition while the modulus of the rubbery plateau increases with PPO concentration. This result is interpreted as a change in the entanglement molecular weight M_e of the blends. When the changes in M_e are considered, the relationship between the zero-shear viscosity η0 and the 3.4 power of the weight-average molecular weight, commonly found for high molecular weight homopolymers, predicts the compositional dependence of η0 for the PPO–PS blends. It is concluded that the PPO–PS system forms a rheologically compatible blend.     

Glass transition in partially sulfonated polystyrene

The glass transition temperature T_g of partially sulfonated polystyrene has been measured dilatometrically as a function of degree of sulfonation. A semitheoretical relationship between T_g and degree of sulfonation has been derived by treating the strong-acid polymer as a highly polar copolymer of styrene and styrenesulfonic acid. The T_g of copolymer has been found to increase linearly up to 0.15 weight fraction of styrene-sulfonic acid w_A as given by: where T_gB is the glass transition temperature of loosely crosslined (1%) polystyrene matrix. Our experimental results agree well with theoretical relations developed on the basis of the iso-free-volume state of glass transition applied to sulfonated polystyrene. The marked linear increase in copolymer T_g with the styrenesulfonic acid is accounted for by the effect of progressively higher intermolecular forces due to the highly polar sulfonic acid substituents.     

Noncovalent columnar structures based on β-cyclodextrin

A new method for the synthesis of associates of cyclodextrins (CDs) of the columnar type consisting of the precipitation of CDs from aqueous solutions into acetone at lowered temperatures is developed. It is shown that columnar structures exist in both a crystalline state and in aqueous solutions. Hydrodynamic radii and molecular masses of noncovalent columnar structures (NCSs) in aqueous solutions are determined by the dynamic and static light scattering methods. The degree of association of noncovalent columnar polymers is ～40. It is revealed the NCS associates based on β-CD are stable and their hydrodynamic radius R _h is equal to 100 ± 10 nm. The kinetics of interactions of initial β-CD and NCS with poly(propylene oxide) (PPO) is studied. The pattern of kinetic curves of R _h growth upon interaction between NCS and PPO indicates that the aggregation of the particles of polymer inclusion complex proceeds in the regime of reaction-limited cluster-cluster aggregation. Kinetic curves describing the interaction processes between β-cyclodextrin and PPO are characterized by the presence of induction period t ₀. At t > t ₀, R _h ∞ t ^0.56 which is typical for the diffusion-limited cluster-cluster aggregation. Schemes of the formation of polymer inclusion complexes between initial β-CD or NCS and poly(propylene oxide) are proposed. Comparison of kinetic data on the complexation of β-CD in solution in the form of associates of two types with PPO demonstrates that columnar forms of associates are reactive species acting as macroreceptors.     

Effect of climate on the weathering of polyacetal

The degrees of weathering of polyacetal specimens exposed for a year at fourteen sites throughout the world have been assessed from weight loss measurements. From a consideration of the results and meteorological data it has been shown that the extent of polyacetal degradation depends on uv dose and temperature. Moisture also affects the degree of breakdown; its effect is to inhibit the photo-oxidative process.An expression, W = 1·58 × 10⁴D e^{?10 000/RT}, is developed which enables polyacetal weight loss at a site to be estimated from a knowledge of the annual uv dose (D) as measured by the PPO film technique and the mean temperature (T) in degrees absolute.From information presented on these two climatic factors, a relationship between site latitude and the degree of polyacetal breakdown is proposed.     

Composition dependence of glass transition temperature of sulfonated-polystrene ionomers

The glass transition temperatures of alkali (Na, K, Rb, Cs) and alkaline-earth (Ba, Sr, Ca, Mg) ionomers of sulfonated polystyrenes (PSSA) with 3.4, 6.9, 12.7, and 16.7% of the styrene moieties sulfonated are reported. For the alkali-metal PSSA ionomers, T_g depends on the degree of sulfonation, at least up to 13%, but not strongly on the nature of the cation. For the alkaline-earth analogs T_g does not depend strongly on either the cation or the degree of sulfonation until the 16.7% level is reached. These and other reported data are discussed in terms of the role of cations in determining morphology.     

Sulfobutylated Lignosulfonate with Ultrahigh Sulfonation Degree and Its Dispersion Property in Low-Rank Coal-Water Slurry

Using a simple method, we developed a new family of alkyl sulfonic acid modified lignosulfonate (ASLSs) with simultaneously improved sulfonation degrees and molecular weights via one step. Direct sulfonation occurred on both phenolic and alcoholic hydroxyl groups of alkali lignin raw material with 1,4-butylenesulfone used as sulfonation agent. A sulfonation degree of 3.86 mmol/g had been achieved which presents as one of the highest sulfonation degrees among those of reported LSs, to date. ¹H-NMR and Fourier transform infrared spectroscopy measurements confirmed the efficient sulfonation. Furthermore, the dispersion properties were investigated in low-rank coal-water slurry (CWS). ASLS3 showed better viscosity-reduction effect than naphthalene sulfonate formaldehyde condensate (FDN) in CWS with dosages from 0.6% to 1.0 wt%. ASLS3 had the similar sulfonation degree with FDN; however, the large steric hindrance, soft long alkyl chain-C₄H₈-SO₃H, and their efficient anchoring effect of ASLSs contributed to their improved dispersion properties.     

Effect of pressure on phase behavior in polymer blends of poly(2,6-dimethyl-1,4-phenylene oxide) and poly(styrene-co-p-fluorostyrene) copolymers

The effect of pressure on the miscibility of blends of poly(2,6-dimethyl-l,4-phenylene oxide) (PPO) with a random copolymer of styrene and para-fluorostyrene, P(S-co-p-FS), has been studied by high pressure differential thermal analysis (HPDTA). P(S-co-p-FS) copolymers less than 36 mole % p-FS are miscible with PPO in all proportions irrespective of pressure up to 200 MPa, using the customary criterion of a single calorimetric glass relaxation. P(S-co-p-FS) copolymers containing 40 to 50 mole % p-FS undergo phase separation upon annealing at elevated temperatures, indicating the existence of a lower critical solution temperature (LCST). In these blends, pressure displaces the phase boundary associated with the LCST to higher temperatures causing an apparent increase in polymer miscibility. The phase diagram for the blend of PPO and P(S-co-p-FS) containing 46 mole % p-FS, shows that the critical composition at about 50 wt % PPO does not change with pressure, but the consolute temperature T_c increases with increasing pressure. The pressure dependence of the LCST (dT_c/dP) of this system is about 0.35°C/MPa.     

New sulfonated engineering polymers via the metalation route. I. Sulfonated poly(ethersulfone) PSU Udel® via metalation-sulfination-oxidation

A new process has been developed for the sulfonation of arylene polymers which can be lithiated, like polysulfone Udel®. The sulfonation process consists of the following steps: (1) lithiation of the polymer at temperatures from −50 to −80°C under argon, (2) gassing of the lithiated polymer with SO₂; (3) oxidation of the formed polymeric sulfinate with H₂O₂, NaOCl, or KMnO₄; (4) ion-exchange of the lithium salt of the sulfonic acid in aqueous HCl. The advantages of the presented sulfonation procedure are: (1) in principle all polymers which can be lithiated can be subjected to this sulfonation process; (2) by this sulfonation procedure the sulfonic acid group is inserted into the more hydrolysis-stable part of the molecule; (3) this process is ecologically less harmful than many common sulfonation procedures. The sulfonated polymers were characterized by NMR, titration and elemental analysis, by IR spectroscopy, and by determination of ionic conductivity. Also the hydrolytic stability of the sulfonated ion-exchange polymers was investigated. Polymers with an ion-exchange capacity of 0.5 to 3.2 mequiv SO₃H/g Polymer have been synthesized and characterized. The following results have been achieved: membranes made from the sulfonated polymers show good conductivity, good permselectivity (>90%), and good hydrolytic stability in 1N HCl and water at temperatures up to 80°C. © 1996 John Wiley & Sons, Inc.     

Synthesis and properties of polyoxyarylenesiloxanes

High molecular weight polymers containing oligosiloxanes in the backbone were made by the reaction of aromatic diols with α,ω-diaminosiloxane homologs. The glass transition temperatures dropped by 30–40°C in a homologous series with each siloxane added. The thermal stability also suffered when increasing the number of siloxane groups. The polymers all displayed high % char measurements and one polymer (disiloxane) tested had a V₀ rating by UL-94 testing. The trisiloxane-containing polymer had a high percent elongation at break (>300%). All the polymers tested were fairly susceptible to hydrolysis. © 1994 John Wiley & Sons, Inc.     

Synthesis and properties of phthalonitrile-terminated oligomeric poly(ether imide)s containing phthalazinone moiety

Three novel series of soluble and curable phthalonitrile-terminated oligomeric poly(ether imide)s containing phthalazinone moiety were synthesized from an excess amount of three dianhydrides and phthalazinone-based diamine, followed by reacting with 4-(3-aminophenoxy)phthalonitrile (APPh) in a two-step, one-pot reaction, respectively. The phthalonitrile oligomers containing phthalazinone moiety were cured in the presence of 4,4′-diaminodiphenylsulfone (DDS). The oligomers and the crosslinked polymers were characterized by DSC, FT-IR and elemental analysis. These phthalonitrile oligomers containing phthalazinone groups were found to be soluble in some aprotic solvents, such as chloroform, pyridine, m-cresol and N-methyl-2-pyrrolidone (NMP). The crosslinked polymers were insoluble in all solvents. The thermal properties of the oligomers and the crosslinked polymers were evaluated using DSC and TGA analysis. The phthalonitrile oligomers showed high glass transition temperatures (T_gs) in the range of 214-256 °C and high decomposition temperatures with 10% weight loss (T_d10%) ranging from 523 to 553 °C. The crosslinked polymers showed excellent thermal stability with the 10% weight loss temperatures ranging from 543 to 595 °C, but did not exhibit a glass transition temperature upon heating to 350 °C.     

A bicyclic conjugated diene monomer,tetrahydroindene, for cationic polymerization and a novel alicyclic hydrocarbon polymer with heat resistance

This study was directed toward the cationic polymerization of tetrahydroindene (i.e., bicyclo[4.3.0]‐2,9‐nonadiene), a bicyclic conjugated diene monomer, with a series of Lewis acids, especially focusing on the synthesis of high‐molecular‐weight polymers and subsequent hydrogenation for novel cycloolefin polymers with high service temperatures. EtAlCl₂ or SnCl₄ induced an efficient and quantitative cationic polymerization of tetrahydroindene to afford polymers with relatively high molecular weights (number‐average molecular weight > 20,000) and 1,4‐enchainment bicyclic main‐chain structures. The subsequent hydrogenation of the obtained poly(tetrahydroindene) with p‐toluenesulfonyl hydrazide resulted in a saturated alicyclic hydrocarbon polymer with a relatively high glass transition (glass‐transition temperature = 220 °C) and improved pyrolysis temperature (10% weight loss at 480 °C). The new diene monomer was randomly copolymerized with cyclopentadiene at various feed ratios in the presence of EtAlCl₂ to give novel cycloolefin copolymers, which were subsequently hydrogenated into alicyclic copolymers with variable glass‐transition temperatures (70–220 °C). © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6214–6225, 2006     

Novel,tadpole-shaped,polyhedral oligomeric silsesquioxane containing sulfonated block copolymer for humidity sensing

Due to the “trade-off” effect between the high water adsorption and low stability under high Relative Humidity of polymer matrix, fabrication of resistive-type polymer-based humidity sensors with a wide impedance response and excellent stability in high relative humidity remains a great challenge. Aim at solving that, a novel polymeric humidity sensing matrix, specifically a tadpole-shaped, polyhedral oligomeric silsesquioxane (POSS) containing block copolymers (BCPs) of POSS-poly(methyl methacrylate)-polystyrene (POSS-PMMA-SPS) were proposed. This novel BCP was synthesized using atom transfer radical polymerization (ATRP) employing a two-step approach, and following post sulfonation, a series of sulfonated BCPs (POSS-PMMA-SPS) with different sulfonation degree was obtained. The subject humidity sensors were produced using different sulfonated BCPs employing a dip-coating technique, and three wide-impedance response humidity sensors were produced. Each of these sensors exhibited an excellent humidity-sensing response of more than 10⁴ within the humidity range from 11% to 95% RH. In particular, the humidity sensor S-6 that had a proper degree of sulfonation presented a relatively fast response (t_90% of 11 s and 80 s in both the water adsorption and desorption processes), and superior repeatability for more than 30 days.