Simultaneous Determination of Heavy Metals in Bovine Liver and Oyster Tissue by Solvent Extraction-Reversed Phase High Performance Liquid Chromatography

Abstract

High performance liquid chromatographie method for the simultaneous determination of ppm levels of cadmium, nickel, lead, zinc, cobalt, copper and bismuth in biological samples has been developed. Each 250 mg of Bovine Liver(NBS 1577) or Oyster Tissue(NBS 1566) was ashed in a muffle furnace over night at 500 to 55O°C. Then the ash was treated with 1.5 ml of 2 N hydrochloric acid; and the solution was put into a separatory funnel. The dissolved heavy metals were extracted into chloroform as hexamethylenedithiocarbamato chelates. The metal chelates were separated on a reversed phase column(5 μm, ODS, 4.6 × 15O mm), and determined by measuring the peak height of each metal chelate. Cd, Ni, Pb, Zn and Cu were determined accurately over the concentration range of 0.5–850 ppm with standard deviation ca. 7%.     

Study of the pyrolysis liquids obtained from different sewage sludge

Pyrolysis of sewage sludge in fluidized bed to produce bio-oil is under study as a useful way to valorise this waste. Sewage sludge is the waste produced in the wastewater treatment plants. Its composition may change due to the origin and to the non-standardized treatments in the wastewater treatment plants. The pyrolysis of three samples of anaerobically digested sewage sludge obtained from three different urban wastewater treatment plants was studied in this work. The organic and inorganic matter composition, and the volatile and ash content of these sewage sludge samples were different. The influence of these parameters on the pyrolysis product distribution and on some characteristics of these products was studied. It was determined that the ash content of the raw material had an enormous influence on the sewage sludge pyrolysis. An increase in the ash content of the sewage sludge caused an increase in the gas yield and a decrease in the liquid and the solid yield with the operational conditions studied. The increase of the volatile content of the sewage sludge samples caused an increase in the liquid yield. The H₂ proportion was the most influenced non-condensable gas. It increased significantly with the ash content. The viscosity of the pyrolysis oils decreased when the ash content augmented. On the other hand, the water content depended on the organic composition of the sewage sludge samples. The chemical composition of the pyrolysis oils was also affected by the sewage sludge ash content above all the proportion of polyaromatic hydrocarbons and nitrogen-containing aromatic compounds. These compound groups increased with the augment of the sewage sludge ash content. The oxygen-containing aliphatic compounds and the steroids decreased with the ash content, although its proportion in the sewage sludge liquid was also influenced by the organic matter composition of the sewage sludge samples.     

Development of an analytical method for the determination of polybrominated diphenyl ethers in sewage sludge by the use of gas chromatography coupled to inductively coupled plasma mass spectrometry

Polybrominated diphenyl ethers (PBDEs) are flame retardants. As a consequence of their widespread use, they have been released into the environment. PBDEs are lipophilic organic contaminants that enter wastewater treatment plants (WWTPs) from urban, agricultural and industrial discharges. Because of their low aqueous solubility and resistance to biodegradation, up to 90% of the PBDEs are accumulated in the sewage sludge during the wastewater treatment. To assess the possibilities for sludge re-use, a reliable determination of the concentrations of these PBDEs is of crucial importance. Six PBDE congeners (BDE 28, BDE 47, BDE 99, BDE 100, BDE 153 and BDE 154) are listed as priority substances under the EU Water Framework Directive. In the present work a simple analytical method with minimal sample-preparation steps was developed for a sensitive and reliable determination of the six PBDEs in sewage sludge by the use of gas chromatography coupled to inductively coupled plasma mass spectrometry (GC-ICP-MS). For this purpose an extraction procedure was optimised. Different extracting agents (methanol (MeOH), acetic acid (AcOH)/MeOH mixture (3:1) and 0.1 mol L⁻¹ hydrochloric acid (HCl) in MeOH) followed by the addition of a Tris-citrate buffer (co-extracting agent) and iso-octane were applied under different modes of extraction (mechanical shaking, microwave- and ultrasound-assisted extraction). Mechanical shaking or the microwave-assisted extraction of sewage sludge with 0.1 mol L⁻¹ HCl in MeOH and the subsequent addition of the Tris-citrate buffer and the iso-octane extracted the PBDEs from the complex sludge matrix most effectively. However, due to easier sample manipulation during the extraction step, mechanical shaking was used. The PBDEs in the organic phase were quantified with GC-ICP-MS by applying a standard addition calibration method. The spike recovery test (recoveries between 95 and 104%) and comparative analyses with the species-specific isotope-dilution (ID) GC-ICP-MS confirmed the accuracy of the developed analytical procedure. The procedure is sensitive (limits of detection (LODs) for PBDEs congeners between 0.2 and 0.3 ng g⁻¹), repeatable and reproducible (RSDs 2.2–5.7%) and was applied for the determination of PBDEs in sewage sludge samples collected three times at the municipal WWTP over a period of 16 years.     

污泥与煤共热解过程中磷元素的挥发规律研究

污泥灰分中磷元素含量明显高于煤,其中主要的晶体态含磷化合物为磷酸铁钙和少量的磷酸铝。利用高频加热反应装置考察了污泥-神府煤混合物快速热解过程中磷元素挥发规律。结果表明,污泥-神府煤混合物热解后磷元素主要存在于热解焦中。磷元素挥发比例随污泥添加比例的增加先升高后降低,随热解温度的升高而增加。热解温度不高于1 100 ℃时,混合物中以有机磷的挥发为主,磷元素挥发比例不高于3.2%。热解温度高于1 200 ℃后无机磷中磷元素挥发明显,1 300 ℃下最高有33.0%的磷元素随热解气体挥发出。     

Determination of Nitrilotriacetic Acid in Waters and Waste Waters by Gas-Liquid Chromatography,Differential Pulse Polarography and a Colorimetric Method

Abstract

A comparison of gas-liquid chromatography, differential-pulse polarography and a colorimetric method for the determination of nitrilotriacetic acid in settled sewage, sewage effluent, potable water, soil extracted water and deionised water has been undertaken. Differential-pulse polarography has also been applied to the determination of nitrilotriacetic acid in saline samples. By statistical analysis of replicate determinations, accuracy and precision have been evaluated, and calibration linearity assessed. Interferences were observed for sewage samples when analysed by all three methods. Precision was generally higher for differential-pulse polarography down to 100 μgl^?1, although only gas-liquid chromatography is applicable to concentrations below 25μgl^?1 in non-saline samples. The colorimetric method was not applicable to concentrations below 500 μgl^?1 of nitrilotriacetic acid.     

Determination of hydride forming elements (As,Sb, Se,Sn) and Hg in environmental reference materials as acid slurries by on-line hydride generation inductively coupled plasma mass spectrometry

A method for the determination of As, Hg, Sb, Se and Sn in environmental and in geological reference materials, as acidified slurries, by flow injection (FI) coupled to a hydride generation system (HG) and detection by inductively coupled plasma mass spectrometry (ICP-MS) is proposed. The HG unit has a gas liquid separator and a drying unit for the generated vapor. The slurries were prepared by two procedures. Approximately 50 mg of the reference material, ground to a particle size ≤50 μm, was mixed with acid solutions in an ultrasonic bath. In Procedure A, the medium was a hydrochloric acid solution while in Procedure B, the medium was aqua regia plus a hydrochloric acid solution. The conditions for the slurry formation and the instrumental parameters were optimized. Harsh conditions were used in the slurry preparation in order to reduce the hydride forming analytes to their lower oxidation states, As (III), Se(IV), Sb(III) and Sn(II), before reacting with sodium tetrahydroborate. To test the accuracy, 10 certified reference materials were analyzed (four sediments, three coals, one coal fly ash and two sewage sludges), with the analyte concentrations mostly in the μg g⁻¹ level. Good agreements with the certified values were obtained for Hg, Sb and Sn in the sediments using Procedure A and calibration against aqueous standard solutions. Using Procedure B, good results were obtained for Hg, Se and Sn in the sediment samples, for Se in the coal and coal fly ash samples and for Hg in the sewage sludge samples, also using external calibration with aqueous standard solutions. For As in sediments, coals and coal fly ash, Procedure B and the analyte addition calibration was required, indicating matrix effects. The relative standard deviations were lower than 5%, demonstrating a good precision for slurry analysis. The limits of quantification (10 times the standard deviation; n=10), in the samples, in ng g⁻¹, were: 20 for As, 60 for Hg, 80 for Sb, 200 for Se and 90 for Sn. The method requires small amounts of reagents and reduces contamination and losses.     

Production of High Purity Amorphous Silica from Rice Husk

Combustion of the rice husk produces rice husk ash, which consists of mainly silica. High purity silica can be produced by controlled combustion after acid treatment. In this study, leaching of rice husk with hydrochloric acid and sulfuric acid were carried out prior to combustion to obtain purer silica. It was found that pre-treatment of the rice husk with sulfuric acid had accelerated the hydrolysis and decomposition of organic components as revealed by thermogravimetry (TG) and Scanning Electron Microscopy (SEM) analyses. In a systematic study, the combustion of un-leached, hydrochloric acid-leached and sulfuric acid-leached rice husks were performed in a muffle furnace at 500, 600, 700, 800 and 900^oC for 2 h. Results demonstrated that all the samples produced amorphous silica (SiO₂) and the average particle size were in the range of 0.50 to 0.70 μm. The effect of combustion at different temperatures between 500^oC and 900^oC on the silica production is very small, particularly at temperature above 600^oC. Thus, amorphous silica with purity above 99% as confirmed by X-Ray Fluorescence (XRF) analysis can be produced by hydrochloric and sulfuric acids leaching of the rice husk, followed by controlled combustion at 600^oC for 2 h. The BET surface area of the silica produced after leaching the rice husk with hydrochloric acid was higher (218 m²/g) than with sulfuric acid (209 m²/g). The silica obtained has potential application as filler in plastics and rubber compounding.     

Investigation of extraction procedures and HPLC-DAD/MS for the determination of the brominated flame retardant tetrabromobisphenol A bis(2,3-dibromopropylether) in environmental samples

A method for the determination of the novel brominated flame retardant tetrabromobisphenol A bis(2,3-dibromopropylether), 1,1′-(isopropylidene)bis[3,5-dibromo-4-(2,3-dibromo-propoxy)-benzene] (TBBPA-dbpe), was developed. Technical TBBPA-dbpe was purified and the results of a thorough physical characterisation are reported. The application of APCI-MS is discussed and the fragmentation patterns are described. Quantification of TBBPA-dbpe was done by HPLC-DAD using external calibration. The validation of the method was accomplished using sediment and sewage sludge samples spiked with defined amounts of authentic TBBPA-dbpe. The average recovery rates of TBBPA-dbpe from spiked samples ranged from 35 to 91% (sediment) and from 57 to 98% (sewage sludge) depending on the respective extraction method. Pressurised fluid extraction (PFE) and fluidised bed extraction were superior to classical Soxhlet and sonication procedures and yielded recovery rates between 90 and 98% with relative standard deviations of 2%. The limits of detection (DTC), identification (ID) and determination (DTM) using HPLC-DAD were 10, 21 and 30 ng g⁻¹ in sediment and 22, 44 and 72 ng g⁻¹ in sewage sludge, respectively.     

Thermal characteristics of the combustion process of biomass and sewage sludge

The combustion of two kinds of biomass and sewage sludge was studied. The biomass fuels were wood biomass (pellets) and agriculture biomass (oat). The sewage sludge came from waste water treatment plant. The biomass and sludge percentage in blends with coal were 10 %. The studied materials were characterised in terms of their proximate and ultimate analysis and calorific value. The composition of the ash of the studied fuels was also carried out. The behaviour of studied fuels was investigated by thermogravimetric analysis (TG, DTG and DTA). The samples were heated from an ambient temperature up to 1,000 °C at a constant three rates: 10, 40 and 100 °C min^?1 in 40 mL min^?1 air flow. TG, DTG and DTA analysis showed differences between coal, biomass fuels and sewage sludge. 10 % addition of studied fuels to the mixture with coal changed its combustion profile in the case of sewage sludge addition. The combustion characteristics of fuel mixtures showed, respectively, qualitative summarise behaviour based on single fuels. Evolved gaseous products from the decomposition of studied samples were identified. This study showed that thermogravimetric analysis connected with mass spectrometry is useful techniques to investigate the combustion and co-combustion of biomass fuels, and sewage sludge, together with coal. Non-isothermal kinetic analysis was used to evaluate the Arrhenius activation energy and the pre-exponential factor. The kinetic parameters were calculated using Kissinger–Akahira–Sunose model.     

Electrothermal atomic absorption spectrometric determination of vanadium in extracts of soil and sewage sludge certified reference materials after fractionation by means of the Communities Bureau of Reference modified sequential extraction procedure

A modified three-step sequential extraction procedure proposed by the Commission of European Communities Bureau of Reference (BCR) was applied to certified reference materials of three different soil groups (rendzina, luvisol, cambisol) and sewage sludge of different composition originating from a municipal water treatment plant in order to assess potential mobility and the distribution of vanadium in the resulting fractions. Analysis of the extracts was carried out by electrothermal atomic absorption spectrometry with Zeeman background correction using transversely heated graphite atomizers. Extracts showed significant matrix interferences which were overcome by the standard addition technique. The original soil and sludge certified reference materials (CRMs) and the extraction residue from the sequential extraction were decomposed by a mixture of HNO₃–HClO₄–HF in an open system. The content of V determined after decomposition of the samples was in very good agreement with the certified total values. The accuracy of the sequential extraction procedure was checked by comparing the sum of the vanadium contents in the three fractions and in the extraction residue with the certified total content of V. The amounts of vanadium leached were in good correlation with the certified total contents of V in the CRMs of soils and sewage sludge. In the soils examined, vanadium was present almost entirely in the mineral lattice, while in the sewage sludge samples 9–14% was found in the oxidizable and almost 25% in the reducible fractions. The recovery ranged from 93–106% and the precision (RSD) was below 10%.     

Sample preparation of sewage sludge and soil samples for the determination of polycyclic aromatic hydrocarbons based on one-pot microwave-assisted saponification and extraction

A microwave-assisted sample preparation (MASP) procedure was developed for the analysis of polycyclic aromatic hydrocarbons (PAHs) in sewage sludge and soil samples. The procedure involved the simultaneous microwave-assisted extraction of PAHs with n-hexane and the hydrolysis of samples with methanolic potassium hydroxide. Because of the complex nature of the samples, the extracts were submitted to further cleaning with silica and Florisil solid-phase extraction cartridges connected in series. Naphthalene, acenaphthene, fluorene, phenanthrene, anthracene, fluoranthene, pyrene, benz[a]anthracene, chrysene, benzo[e]pyrene, benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[a]pyrene, dibenz[a,h]anthracene, benzo[g,h,i]perylene, and indeno[1,2,3-cd]pyrene, were considered in the study. Quantification limits obtained for all of these compounds (between 0.4 and 14.8 μg kg⁻¹ dry mass) were well below of the limits recommended in the USA and EU. Overall recovery values ranged from 60 to 100%, with most losses being due to evaporation in the solvent exchange stages of the procedure, although excellent extraction recoveries were obtained. Validation of the accuracy was carried out with BCR-088 (sewage sludge) and BCR-524 (contaminated industrial soil) reference materials.     

Speciation of Metals in Soils

Abstract

Our studies have centred around the speciation of cadmium and manganese in three soils, one of which has been amended with sewage sludge. We report here some of our preliminary results, obtained by a coupled high performance liquid chromatography (HPLC)—graphite furnace atomic absorption spectroscopy (GFAAS) technique.

The results indicate that cadmium may exist in different forms in soil, but only one form in soil-pore waters. Manganese is present in different soil-pore waters in different forms. The presence of sewage sludge in the soil can also affect the quantity and form of metals in water extracts.     

Sewage sludge ash as an alternative low-cost oxygen carrier for chemical looping combustion

In this paper, novel low-cost oxygen carriers containing Fe₂O₃ are evaluated for use in chemical looping combustion. Sewage sludge ashes and reference samples were prepared and used in cyclic reduction and oxidation experiments in a thermogravimetric analyzer (TG). A gaseous (3 % H₂) fuel and a solid fuel (hard coal) were tested. Three-cycle CLC tests were carried out in the 600–800 °C temperature range and long-term testing was performed at 950 °C. A reactivity study showed that the natural sewage sludge ash sample was stable during the cycling TG tests when hydrogen was used as a fuel at all of the temperatures investigated. Strong temperature effects on the oxygen transport capacity were observed. An one-cycle test at 900 °C showed also that the sewage sludge ash successfully reacted with coal. The oxygen released was fully used for coal combustion, with appreciable reaction rate at temperature of ~750–800 °C, that is significantly lower than that obtained for pure Fe₂O₃-based oxygen carrier. The oxidation reaction was much faster than the reduction reaction. Moreover, the sewage sludge ash showed a low tendency toward agglomeration in the cyclic test, which was superior to the behavior of synthetic materials. The sewage sludge ash exhibited also high mechanical strength, an attrition index of 1 % and a high-temperature resistance of 1,170 °C in a reducing atmosphere. We conclude that sewage sludge ash can be effectively used as a low-cost, valuable oxygen carrier in practical application in chemical looping combustion technology for power generation.     

Determination of pesticide residues in sewage sludge: a review

Pesticides are widely applied to protect plants from diseases, weeds, and insect damage, and they usually come into contact with soil where they may undergo a variety of transformations and provide a complex pattern of metabolites. Spreading sewage sludge on agricultural lands has been actively promoted by national authorities as an economic way of recycling. However, as a byproduct of wastewater treatment, sewage sludge may contain pesticides and other toxic substances that could be incorporated into agricultural products or be distributed in the environment. This article reviews the determination of pesticides in sewage sludge samples. Sample preparation including pretreatment, extraction, and cleanup, as well as the subsequent instrumental determination of pesticide residues, are discussed. Extraction techniques such as Soxhlet extraction, ultrasound-assisted extraction, pressurized liquid extraction, supercritical fluid extraction, and matrix solid-phase dispersion and their most recent applications to the determination of pesticides in sewage sludge samples are reviewed. Determination of pesticides, generally carried out by GC and HPLC coupled with different detectors, especially MS for the identification and quantification of residues, is summarized and discussed.     

Atomic-absorption spectrometric determination of catalytic components (Pd,Ti, and Cu) in mixtures based on phenol

Procedures for the determination of palladium, titanium, and copper in organic reaction mixtures based on phenol were developed with the use of atomic absorption spectrometry and various sample preparation techniques: quantitative back extraction of the metals with a 2 M HCl solution; autoclave digestion in an acid mixture of HClO₄, HF, and HNO₃; and decomposition in a muffle furnace. The accuracy of analysis was demonstrated by a comparison between the results of the atomic-absorption spectrometric determination of the elements obtained with the use of all of the sample preparation techniques proposed and the standard addition method. The relative standard deviation in the determination of palladium, copper, and titanium was 7–10%.     

Determination of dialkyldimethylammonium compounds and other cationic surfactants in sewage water and activated sludge

Summary A method for the extraction and clean-up of four groups of cationic surfactants in sewage water and activated sludge is reported. In the case of sewage water, this is based on the extraction of the acidified aqueous sample with chloroform, centrifugation, purification by back-extraction with water and clean-up by alumina column chromatography. Activated sludge was extracted with methanolic hydrochloric acid after centrifugation. The extract was evaporated to dryness and re-dissolved in chloroform before further clean-up. The surfactants are determined by high-performance liquid-chromatography using a diol column (mobile phase methanol/tetrahydrofuran/0.25 mmol/1 hydrochloric acid) and a conductivity detector. The applicability of this analytical scheme to the new esterquats is discussed.Dedicated to Professor Dr. Wilhelm Fresenius on the occasion of his 80th birthday     

Development of a sample preparation procedure of sewage sludge samples for the determination of polycyclic aromatic hydrocarbons based on selective pressurized liquid extraction

An automated, simple and sensitive method based on selective pressurized liquid extraction (SPLE) was developed for the analysis of polycyclic aromatic hydrocarbons in sewage sludge samples. The new sample preparation procedure consists of on-line clean-up by inclusion of sorbents in the extraction cell, and combines elevated temperatures and pressures with liquid solvents to achieve fast and efficient removal of target analytes from complex sewage sludge matrices. The effects of various operational parameters (e.g. sample pretreatment, extraction solvent, temperature, pressure, static time, etc.) on the performance of SPLE procedure were carefully investigated, obtaining the best results when SPLE conditions were fixed at 140 °C, 1500 psi, static time of 5 min and n-hexane as extraction solvent. A new programmed temperature vaporization–gas chromatography–tandem mass spectrometry method based on large volume injection (PTV–LVI–GC–MS/MS) was also developed and analytical determinations were performed by high performance liquid chromatography coupled with fluorescence detection and GC–MS/MS. The extraction yields for the different compounds obtained by SPLE ranged from 84.8% to 106.6%. Quantification limits obtained for all of these studied compounds (between 0.0001 and 0.005 μg g⁻¹, dry mass) were well below the regulatory limits for all compounds considered. To test the accuracy of the SPLE technique, the optimized methodology was applied to the analysis of a certified reference material (sewage sludge (BCR088)) and a reference material (sewage sludge (RTC-CNS312-04)), with excellent results.     

微波消解-磷钼蓝分光光度法测定城市污泥中总磷浓度

建立了微波消解-磷钼蓝分光光度法测定城市污泥中总磷的方法。在微波环境中硝酸-过氧化氢能够将城市污泥中无机磷盐和含磷有机物消解为正磷酸盐,在弱酸性条件下,正磷酸盐在铋盐的催化条件下与钼酸铵-抗坏血酸生成磷钼蓝,于分光光度计波长690nm处进行测定总磷浓度。方法的相对标准偏差0.63%～0.95%,加标回收率为101%～102%,能够满足对城市污泥中总磷浓度的测定要求。     

Hollow fiber liquid phase microextraction as a preconcentration and clean-up step after pressurized hot water extraction for the determination of non-steroidal anti-inflammatory drugs in sewage sludge

A method for the quantitative determination of non-steroidal anti-inflammatory drugs (NSAIDs) in sewage sludge was developed and validated. The target compounds were extracted using pressurized hot water extraction (PHWE) and then purified and preconcentrated by three-phase hollow fiber liquid phase microextraction (HF-LPME) followed by LC–ESI-MS analysis. The PHWE was optimized with regard to the pH of solvent as well as other operational parameters. The optimum conditions were 0.01 M NaOH as the extraction solvent, temperature of 120 °C, pressure of 100 bar, static time 5 min, 5 cycles, flush volume 90% and purge time 60 s. Spike recoveries for sludge samples spiked at 200 ng g⁻¹ were in the range of 101–109% but for the native drugs in non-spiked sludge samples, recoveries were 38.9%, 59.8%, 90.3% and 47.8% for ketoprofen, naproxen, diclofenac and ibuprofen, respectively. Donor phase pH, ionic strength and extraction time were optimized for HF-LPME after PHWE. The optimum conditions were 2 h extraction at pH 1.5 without salt addition. Enrichment factors in the range of 947–1213 times were achieved (extraction recoveries were 23.6–30.3%) for HF-LPME after PHWE. The matrix effect on the ionization of drugs in LC–ESI-MS was also investigated. The results show that there is a smaller matrix effect (−8.9% to +14.6%) in comparison with other published values obtained using solid phase extraction (SPE) for clean-up after pressurized liquid extraction (PLE). Method detection limits (MDLs) and method quantification limits (MQLs) for different drugs were in the range of 0.4–3.7 ng g⁻¹ and 1.5–12.2 ng g⁻¹ in dried sludge samples, respectively. The characteristics of the proposed method were compared with those of other published works. The considerably lower ion suppression/enhancement and minimum use of organic solvents (a few microliters of di-n-hexyl ether) in the sample preparation step are two highlighted advantages of the proposed method in comparison with previously published works. The method was applied to determine NSAIDs in sewage sludge from Källby wastewater treatment plant (Lund, Sweden) in April, June, August and October 2010. The highest concentration level was recorded for ibuprofen in the April sewage sludge sample (588 ng g⁻¹) and all of the selected NSAIDs were detected in all the samples analyzed.     

Improved sample treatment for the determination of insoluble soap in sewage sludge samples by liquid chromatography with fluorescence detection

A new selective and sensitive method for the determination of insoluble fatty acid salts (soap) in sewage sludge samples is proposed. The method involves a clean up of sample with petroleum ether, the conversion of calcium and magnesium insoluble salts into soluble potassium salts, potassium salts extraction with methanol, and a derivatization procedure previous to the liquid chromatography with fluorescence detection (LC-FLD) analysis. Three different extraction techniques (Soxhlet, microwave-assisted extraction and ultrasounds) were compared and microwave-assisted extraction (MAE) was selected as appropriate for our purpose. This allowed to reduce the extraction time and solvent waste (50 mL of methanol in contrast with 250 mL for Soxhlet procedure). The absence of matrix effect was demonstrated with two standards (C_13:0 and C_17:0) that are not commercials and neither of them has been detected in sewage sludge samples. Therefore, it was possible to evaluate the matrix effect since both standards have similar environmental behaviour (adsorption and precipitation) to commercial soaps (C_10:0-C_18:0). The method was successfully applied to samples from different sources and consequently, with different composition.