Chitosan‐Based Glucose Oxidase Electrodes Enhanced by Silver Nanoparticles

Silver nanoparticles enhanced glucose oxidase electrodes were prepared on the basis of chitosan matrix. The enzyme electrodes exhibited high sensitivity and excellent response performance to glucose with a linear range from 1×10^?6 to 8×10^?3 mol · L^?1. And the time reaching the steady‐state amperometric response was less than 5 seconds. The inhibition percentage of this enzyme electrode against copper ions concentration was linear ranging from 1.2×10^?6 to 5×10^?5 mol · L^?1. These properties of enzyme electrodes are probably due to the excellent electron transfer of silver nanoparticles and the orientation of glucose oxidase molecule.     

Pure copper vs. mixed copper and palladium hexacyanoferrates for glucose biosensing applications

A glucose amperometric biosensor was developed. Glucose oxidase enzyme was immobilized by means of a Nafion membrane on glassy carbon modified with an electrochemically deposited mixed Cu and Pd hexacyanoferrate (CuPdHCF). According to the data provided by X-ray atomic spectroscopy measurements, this Cu- and Pd-based hexacyanoferrate is likely to be a mixture of single CuHCF and PdHCF pure phases. The biosensor performances were evaluated by recording the steady-state currents due to submillimolar additions of glucose to a potassium buffer solution (pH 5.5) and exploiting the electrocatalytic reduction of the enzymatically produced hydrogen peroxide. The CuPdHCF-based biosensor exhibited a sensitivity of 8.1?±?0.6 A M^?1 m^?2, a limit of detection of 1.4?×?10^?5 M, and a linear response range extending between 5?×?10^?5 and 4?×?10^?4 M, with a dynamic response range up to 4?×?10^?3 M glucose. Electrode sensitivity and signal stability resulted more satisfactory as compared to those of a CuHCF-based biosensor fabricated according to the same procedure. The selectivity was investigated through an interference study. The response to easily oxidizable species was found to be low enough to allow glucose determination in biological samples.     

Amperometric Biosensors Based on Platinum Nanowires

Abstract

Platinum nanowires (PtNW) were prepared by an electrodeposition strategy using nanopore alumina template. The nanowires prepared were dispersed in chitosan (CHIT) solution and stably immobilized onto the surface of glassy carbon electrode (GCE). The electrochemical behavior of PtNW‐modified electrode and its application to the electrocatalytic reduction of hydrogen peroxide (H₂O₂) are investigated. The modified electrode allows low potential detection of hydrogen peroxide with high sensitivity and fast response time. As an application example, the glucose oxidase was immobilized onto the surface of PtNW‐modified electrode through cross‐linking by glutaric dialdehyde. The detection of glucose was performed in phosphate buffer at –0.2 V. The resulting glucose biosensor exhibited a short response time (<8 s), with a linear range of 10^?5?10^?2 M and detection limit of 5×10^?6 M.     

一种基于壳聚糖固定葡萄糖氧化酶的葡萄糖生物传感器的研究

本文选用生物相容性好的壳聚糖作为基体材料，使其与戊二醛交联成网状结构包埋葡萄糖氧化酶制成电化学传感器。这种壳聚糖膜不仅可以减小葡萄糖氧化酶的流失，而且能为酶提供了适宜的微环境。用红外光谱、紫外光谱及透射电镜对膜的形态和性质进行了表征。实验结果表明该传感器具有很快的响应速度，很好的稳定性和重现性，能选择性地催化葡萄糖并测定其浓度。该传感器的制备方法简单，成本低，于冰箱中放置两周信号保持在90％以上，对葡萄糖测量的线性范围为1×10^-5 - 3.4×10^-3mol•L^-1，当信噪比为3:1时检测限为5×10^-6mol•L^-1。     

Novel glucose biosensor based on a glassy carbon electrode modified with hollow gold nanoparticles and glucose oxidase

A novel glucose biosensor is presented as that based on a glassy carbon electrode modified with hollow gold nanoparticles (HGNs) and glucose oxidase. The sensor exhibits a better differential pulse voltammetric response towards glucose than the one based on conventional gold nanoparticles of the same size. This is attributed to the good biological conductivity and biocompatibility of HGNs. Under the optimal conditions, the sensor displays a linear range from 2.0?×?10^?6 to 4.6?×?10^?5?M of glucose, with a detection limit of 1.6?×?10^?6?M (S/N?=?3). Good reproducibility, stability and no interference make this biosensor applicable to the determination of glucose in samples such as sports drinks.

A Prospect for the Analysis of Species Acting as Enzyme Inhibitors as Illustrated by Heavy Metal Inhibition

Abstract

A flow system incorporating an amperometric glucose oxidase enzyme electrode has been used to study the inhibitory effects of 16 metal cations on glucose oxidase. Only copper(II), mercury(II) and silver(I) caused any significant inhibition. the enzyme electrode could be reactivated by EDTA, the reactivation being most effective for copper(II) and least so for silver(I). Other complexing agents were tried for reactivation but proved to be unsatisfactory.

The ability to reactivate the enzyme on the electrode following copper(II) inhibition, and the linear response of the system to the level of this inhibitor according to I/A = -9.49 × 10^?7 log([Cu]/M) + 4.84 × 10^?8; r = 0.994 between 2.5 × 10^?4M and 5 × 10^?3M [Cu]²⁺ indicates a prospect for the use of a flow system for determining enzyme inhibitors in samples.     

Enzymes Immobilized on a Tubular Reactor for Fast Amperometric Determination of Glucose in Brazilian Honey

Abstract

Glucose present in honey was rapidly determined by the differential amperometric method using two tubular reactors containing glucose oxidase and peroxidase. The linear dynamic range extends from 5 × 10^?5 to 2 × 10^?4mol L^?1, at pH 7.0. At flow rate of 1.5 mL min^?1 and injecting 150-µL sample volumes, a sampling frequency of the 33 determinations per hour is afforded. The reproducibility of the methods showed a relative standard deviation (RSD) < 4%. The detection limit of this method is 1.7 × 10^?5 mol L^?1. The samples analyses were compared with the parallel spectrophotometric determination.     

Detection of Biogenic Amines in Human Saliva Using a Screen-Printed Biosensor

An electrochemical biosensor to detect biogenic amines in saliva was developed. This biosensor is based on a Prussian Blue screen-printed electrode, which senses the H₂O₂ produced by the reaction catalyzed by the diamine oxidase enzyme. The probe was connected with a portable instrument and chronoamperometric drop measurements were performed. After evaluation of the biosensor's ability to interact with different amines, putrescine was chosen as the reference amine. A detection limit of 1 × 10^?5 M and a working range between 2 × 10^?5 and 3 × 10^?4 M were obtained. Once optimized, the saliva treatment, a negligible matrix effect, and an average recovery of 105% were obtained.     

二茂铁衍生物电子传递剂键合的溶胶-凝胶葡萄糖生物传感器

The sol-gel derived glucose biosensor was developed, and the sol-gel membrane was organically modified by N-（3-triethoxysilylpropyl）-ferrocenylmethylamine （FcSi） as sol-gel precursor to make electrochemical biosensor. The structure of biosensor was sol-gel/FcSi＋GOx/GC type （glucose oxidase, GOx）. The ferrocene mediator was chemically immobilized to the silane network, and GOx was entrapped to the sol-gel glass network. Therefore, these structures prevented mediator leakage and retained the enzyme activity. Additionally, pH of electrolyte, temperature effects, and interference of positive substances with biosensor were investigated. And the electrochemical performance of biosensor was studied by amperometry. The results indicated that the linear range, detection limit. and response slope of biosensor was 2.00×10^-4-1.57×10^-3 mol·L^-1, 2.0×10^-4 mol·L^-1 and 5.06×10^5 nA·mol^- 1·L, respectively.     

Cholesterol oxidase biosensor based on a glassy carbon electrode modified with Nafion and methyl viologen

Cholesterol oxidase biosensor has been constructed by using bovine serum albumin and glutaraldehyde as cross linker to immobilize cholesterol oxidase and cholesterol esterase on a glassy carbon electrode modified with Nafion and methyl viologen. The biosensor has been used to determine total cholesterol in blood. The linear range of the determination is 2.5×10~7 to 1.0×10-4 mol/L. The detection limit is about 5.0×10~8 mol/L. The response time is 12 s. This biosensor has the advantage of high selectivity, sensitivity and short response time.     

Amperometric Glucose Biosensor Based on the Deposition of Copper and Glucose Oxidase onto Glassy Carbon Transducer

ABSTRACT

The performance of a first generation glucose amperometric biosensor based on the entrapment of glucose oxidase (GOx) within a net of copper electrodeposited onto activated glassy carbon electrode, is described. The copper electrodeposited offers an efficient electrocatalytic activity towards the reduction of enzymatically-liberated hydrogen peroxide, allowing for a fast and sensitive glucose quantification. The influence of the electrodeposition conditions (pH, potential, time, copper salt and enzyme concentrations) on the response of the bioelectrode was evaluated from the amperometric signals of hydrogen peroxide and glucose. The combination of copper electrodeposition with a nation membrane allows an excellent selectivity towards easily oxidizable compounds such as uric and ascorbic acids at an operating potential of -0.050 V. The response is linear up to 2.0 × 10^?2 M glucose, the detection limit being 1.2 × 10^?3 M.     

Pt nanoparticles modified Au nanowire array for amperometric and potentiometric detection of glucose

A new glucose biosensor, based on the modification of highly ordered Au nanowire arrays (ANs) with Pt nanoparticles (PtNPs) and subsequent surface adsorption of glucose oxidase (GOx), is described. Morphologies of ANs and ANs/PtNPs were observed by scanning electron microscope. The electrochemical properties of ANs, ANs/GOx, ANs/PtNPs, and ANs/PtNPs/GOx electrodes were compared by cyclic voltammetry. Results obtained from comparison of the cyclic voltammograms show that PtNPs modification enhances electrochemical catalytic activity of ANs to H₂O₂. Hence, ANs/PtNPs/GOx biosensor exhibits much better sensing to glucose than ANs/GOx. Optimum deposition time of ANs/PtNPs/GOx biosensor for both amperometric and potentiometric detection of glucose was achieved to be 150 s at deposition current of 1?×?10^?6 A. A sensitivity of 0.365 μA/mM with a linear range from 0.1 to 7 mM was achieved for amperometric detection; while for potentiometric detection the sensitivity is 33.4 mV/decade with a linear range from 0.1 to 7 mM.     

Amperometric Glucose Biosensor Based on Glucose Oxidase Encapsulated in Carbon Nanotube–Titania–Nafion Composite Film on Platinized Glassy Carbon Electrode

A highly sensitive and selective glucose biosensor has been developed based on immobilization of glucose oxidase within mesoporous carbon nanotube–titania–Nafion composite film coated on a platinized glassy carbon electrode. Synergistic electrocatalytic activity of carbon nanotubes and electrodeposited platinum nanoparticles on electrode surface resulted in an efficient reduction of hydrogen peroxide, allowing the sensitive and selective quantitation of glucose by the direct reduction of enzymatically‐liberated hydrogen peroxide at ?0.1 V versus Ag/AgCl (3 M NaCl) without a mediator. The present biosensor responded linearly to glucose in the wide concentration range from 5.0×10^?5 to 5.0×10^?3 M with a good sensitivity of 154 mA M^?1cm^?2. Due to the mesoporous nature of CNT–titania–Nafion composite film, the present biosensor exhibited very fast response time within 2 s. In addition, the present biosensor did not show any interference from large excess of ascorbic acid and uric acid.     

A Novel Fiber Optic Biosensor for the Determination of Adrenaline Based on Immobilized Laccase Catalysis

Abstract

A novel fiber optic biosensor for the determination of adrenaline based on immobilized laccase catalysis and fluorescence quenching was designed and fabricated. The immobilized laccase formed by the immobilization of laccase on the CuTAPc-Fe₃O₄ nanoparticles composite were used to catalyze the oxidation of adrenaline and the fluorescent oxygen-sensing membrane was used to detect the consumption of oxygen. The effects of pH and temperature on laccase activity using adrenaline as the substrate were studied. The optimal pH and temperature for the activity of immobilized laccase are 5.0 and 55°C, respectively. The immobilized laccase has good thermal, storage and operation stability. The lock-in technology was used to detect the change of the life time of the oxygen-sensing membrane. By using ABTS as the electron mediator, the biosensor showed a response time of 30 sec. The biosensor has good performance in the adrenaline concentration ranges of 2.0 × 10^?7 to 9.0 × 10^?7 mol/l and 1.0 × 10^?8 to 9.0 × 10^?8 mol/l, and it also shows good stability.     

Amperometric Biosensor for Evaluation of Competitive Cholinesterase Inhibition by the Reactivator HI‐6

Abstract

Amperometric biosensors containing enzymes butyrylcholinesterase or acetylcholinesterase were prepared. The biosensors were employed for studying of cholinesterase reactivator: HI‐6. Competitions between HI‐6 and acetylthiocholine as enzyme substrate were used for determination of IC₅₀ value. Biosensors with butyrylcholinesterase from human serum determined IC₅₀ as (1.00±0.02)×10^?6 M; the biosensor with acetylcholinesterase from human erythrocytes performance provided IC₅₀ (3.31±0.13)×10^?6 M, the one with human recombinant acetylcholinesterase (2.00±0.06)×10^?6 M and finally biosensor with acetylcholinesterase from electric eel (6.17±0.17)×10^?6 M when 5 mM acetylthiocholine as substrate was used. We are encouraged to consider presented biosensors as a very useful for evaluation of newly prepared cholinesterase reactivators.     

Glucose oxidase inhibition in poly(neutral red) mediated enzyme biosensors for heavy metal determination

A biosensor for the determination of heavy metal cations based on glucose oxidase enzymatic inhibition has been developed. The biosensor was assembled on carbon film electrode supports with glucose oxidase immobilised by cross-linking with glutaraldehyde on top of a film of poly(neutral red) as redox mediator, prepared by electropolymerisation. The biosensor was used to determine the metallic cations, cadmium, copper, lead and zinc in the presence of chosen amounts of glucose. The detection limits were found to be 1 μg L^?1 for cadmium, 6 μg L^?1 for copper, 3 μg L^?1 for lead and 9 μg L^?1 for zinc. Inhibition constants were determined by using the Dixon plot, and the type of inhibition induced by the metallic cations was evaluated from Cornish-Bowden plots plus Dixon plots, it being found that the inhibition is reversible and competitive for cadmium, mixed for copper and lead and uncompetitive for zinc. Copper-inhibited glucose oxidase to a greater extent followed by cadmium, lead and zinc. Regeneration of the glucose oxidase response was studied by using Ethylene diamine tetracetic acid metal-chelating agent and the nonionic surfactant Triton X-100. The suitability of the biosensor for determination in foodstuffs or beverages which contain trace concentrations of metals was investigated by performing recovery tests in commercial milk samples.     

An amperometric monoamine oxidase biosensor for determining some antidepressants

An amperometric biosensor based on a platinum screen-printed electrode and immobilized monoamine oxidase is developed to determine antidepressants of different classes. Petylyl, pyrazidol, and flu-oxetine can be determined with determination limits of 8 × 10^?9, 8 × 10^?7, and 8 × 10^?10 M, respectively. A procedure is proposed for determining fluoxetine in tablets. It is shown that petylyl can be selectively determined by an immunochemical technique using the developed biosensor and immobilized antibodies in the concentration range from 1 × 10^?4 to 1 × 10^?8 M.     

Supramolecular immobilization of glucose oxidase on gold coated with cyclodextrin-modified cysteamine core PAMAM G-4 dendron/Pt nanoparticles for mediatorless biosensor design

Cysteamine core polyamidoamine G-4 dendron branched with β-cyclodextrins was chemisorbed on the surface of Au electrodes and further coated with Pt nanoparticles. Adamantane-modified glucose oxidase was subsequently immobilized on the nanostructured electrode surface by supramolecular association. This enzyme electrode was used to construct a reagentless amperometric biosensor for glucose, making use of the electrochemical oxidation of H₂O₂ generated in the enzyme reaction. The amperometric response of the biosensor was rapid (6 s) and a linear function of glucose concentration between 5 and 705 μmol?L^?1. The biosensor had a low detection limit of 2.0 μmol?L^?1, sensitivity of 197 mA?mol^?1?L?cm^?2, and retained 94 % of its initial response after storage for nine days at 4 °C.     

Laccase-Nafion Based Biosensor for the Determination of Polyphenolic Secondary Metabolites

A laccase-based biosensor was developed by specific enzyme adsorption on screen-printed working electrodes of DROPSENS cells, and stabilized with Nafion 0.1% membrane. The electrode was characterized with respect to response time, sensitivity, linear range, detection limit, pH dependence, interferences, and long-term stability. The tested substrates were catechol, rosmarinic acid, caffeic acid, chlorogenic acid, and gallic acid. The optimized biosensor proved the following characteristic performances: the apparent Michaelis Menten calculated considering rosmarinic acid substrate 8.3 × 10^?6 mol L^?1 (r = 0.995, n = 6); the dynamic range of biosensor response for rosmarinic acid 7 × 10^?7 ? 1.5 × 10^?6 mol L^?1; the detection limit for rosmarinic acid 1.19 × 10^?7 mol L^?1 (RSD = 1.08%, n = 3). It was noticed that the biosensor reaches systematically 90% to 94.3% from the response obtained by LC-DAD-ESI-MS for real samples.     

Biosensor for Hydrogen Peroxide Based on Chitosan and Nanoparticle Complex Film–Modified Glassy-Carbon Electrodes

Abstract

A biosensor for hydrogen peroxide was fabricated by co-immobilizing cadmium telluride (CdTe) nanoparticles, chitosan, and hemoglobin (Hb) matrix. There was a pair of nearly reversible redox peaks around ?0.360 V, and the electrochemical behavior of Hb was a surface-controlled process, with an electron-transfer rate constant of 1.36 s^?1 and surface coverage of 2.62 × 10^?10 mol cm^?2. Fourier transform infrared (FT-IR) spectra and ultraviolet–visible (UV-vis) spectra indicated that Hb sustained its natural conformation. It was demonstrated that Hb in the matrix kept its bioactivity and exhibited catalytic ability toward H₂O₂, with a response ranging from 7.44 × 10^?6 to 6.95 × 10^?4 M and a detection limit of 2.23 × 10^?6 M.