Development of sulfonated poly (ether ether ketone) electrolyte membrane for applications in hydrogen sensor

The future economy is projected as hydrogen economy and fuel cells are set to become the energy source either replacing or augmenting the present oil based technology. A sulfonated poly ether ether ketone (SPEEK) membrane as the electrolyte for hydrogen sensor that operates at room temperature was developed in our lab. The electrolyte used was SPEEK, which is a proton conducting solid polymer membrane. The membranes were characterized using various available techniques like TGA, XRD, SEM, etc. The durability was studied using the Fenton’s reagent. The proton conducting ability was analyzed using impedance spectroscopy. The catalysts considered were platinum for the cathode and three different catalysts (Pt, Pt/Pd and Pd) for the anode. The MEAs were evaluated for their performance in hydrogen sensor and the one with platinum catalyst at the anode gave the best response among the three indicating its suitability for the SPEEK membrane for hydrogen sensor.     

Electrochemical characterization of polyelectrolyte/gold nanoparticle multilayers self-assembled on gold electrodes

Polyelectrolyte/gold nanoparticle multilayers composed of poly(l-lysine) (pLys) and mercaptosuccinic acid (MSA) stabilized gold nanoparticles (Au NPs) were built up using the electrostatic layer-by-layer self-assembly technique upon a gold electrode modified with a first layer of MSA. The assemblies were characterized using UV-vis absorption spectroscopy, cyclic and square-wave voltammetry, electrochemical impedance spectroscopy, and atomic force microscopy. Charge transport through the multilayer was studied experimentally as well as theoretically by using two different redox pairs [Fe(CN)(6)](3-/4-) and [Ru(NH(3))(6)](3+/2+). This paper reports a large sensitivity to the charge of the outermost layer for the permeability of these assemblies to the probe ions. With the former redox pair, dramatic changes in the impedance response were obtained for thin multilayers each time a new layer was deposited. In the latter case, the multilayer behaves as a conductor exhibiting a strikingly lower impedance response, the electric current being enhanced as more layers are added for Au NP terminated multilayers. These results are interpreted quite satisfactorily by means of a capillary membrane model that encompasses the wide variety of behaviors observed. It is concluded that nonlinear slow diffusion through defects (pinholes) in the multilayer is the governing mechanism for the [Fe(CN)(6)](3-/4-) species, whereas electron transfer through the Au NPs is the dominant mechanism in the case of the [Ru(NH(3))(6)](3+/2+) pair.     

Impedance spectra analysis of thermoresponsive poly(acryloyl‐L‐proline methyl ester) gel membrane in LiCl solution

Impedance spectra analysis of a thermoresponsive poly(acryloyl‐L ‐proline methyl ester) (poly(A‐ProOMe)) hydrogel membranes in an aqueous solution of LiCl was carried out using a simple equivalent model. The hydrogel membrane was synthesized by γ‐radiation‐induced polymerization and crosslinking of A‐ProOMe monomer aqueous solution in a glass‐cast. By means of the impedance spectra analysis, a novel method for the calculation of the ionic conductivity of the hydrogel membranes in LiCl solution was proposed. The calculated ionic conductivity was in agreement with the determined value. In addition, effects of temperature and LiCl concentration on the impedance spectra and ionic conductivity of the gel membrane were analyzed. Results indicated that the impedance spectra analysis is a very useful tool for evaluating the electric properties of gel membranes in an electrolyte solution. The poly (A‐ProOMe) gel membrane in 1.0 M LiCl solution showed a high ionic conductivity of about 0.2 S/cm at 14 °C. The temperature‐dependence of the ionic conductivity was a complex nonlinear form due to the volume phase transition of the thermoresponsive poly(A‐ProOMe) gel membrane, and the volume phase transition temperature appeared to be decreased with the increase in the LiCl concentration. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2843–2851, 2005     

Self-assembled film of poly(4-carboxyphenyl)acetylene and diazoresin and its photoelectric conversion property

A novel multilayer film was assembled from water-soluble poly(4-carboxyphenyl)acetylene sodium salt (PCPA) and diazoresin (DR) in aqueous solution via electrostatic attraction. Under UV irradiation, following the decomposition of the diazonium group between the adjacent interfaces of the multilayers, the ionic bonds of the self-assembled film convert to covalent bonds and the film becomes very stable toward electrolyte aqueous solutions. Thus, the photoelectric conversion property of PCPA-containing film can be measured in a conventional three-electrode photoelectrochemical cell, and 0.5 mol/l KCl solution can be used as the supporting electrolyte. The photocurrent spectroscopy response coincides with the absorption spectrum of the irradiated self-assembled film, which indicates that the irradiated DR/PCPA film is responsible for the photocurrent generation.     

聚合物电解质界面性质交流阻抗研究

合成了一种新型聚合物基质材料聚(甲基丙烯酸甲酯-丙烯腈-甲基丙烯酸锂)(简记为PMAML),并以PMAML/PVDF-HFP(偏氟乙烯-六氟丙烯共聚合物)复合物为基质制备了聚合物电解质.利用FTIR对合成的PMAML进行结构表征,并用扫描电镜观察聚合物基质膜的表面形貌.聚合物电解质由聚合物基质膜浸渍电解质溶液得到,其室温电导率可达到2.6×10－3 S• cm－1.利用交流阻抗技术研究了聚合物电解质与锂电极间的界面性质,并考察了开路放置时间、循环伏安及恒流充电对界面阻抗的影响.结果表明,聚合物电解质与锂电极界面阻抗随放置时间的延长而增加,更新锂电极表面可降低界面阻抗,PMAML能提高界面稳定性.     

Swelling and shrinking of polyelectrolyte microcapsules in response to changes in temperature and ionic strength

Swelling and shrinking of polyelectrolyte microcapsules consisting of poly(styrene sulfonate, sodium salt) (PSS) and poly(diallyldimethyl ammonium) chloride (PDADMAC) multilayers have been observed in response to temperature and electrolyte exposure, respectively. Heat-induced capsule swelling and capsule wall volume reduction were observed by confocal laser scanning microscopy (CLSM) and scanning force microscopy (SFM). On the other hand, pronounced shrinking in diameter induced by exposure to an electrolyte was observed in parallel to increases in the thickness of the capsule wall. The estimated wall volume was reduced to two thirds of the control for the salt-exposed capsules and one half for the salt-exposed and simultaneously annealed capsules. This reduction in volume was supposedly mainly caused by the compression of the capsule wall due to the ionic screening from the electrolyte. The highly porous microstructure of the multilayers and loosely bound PSS/PDADMAC complex are thought to be responsible for the structure of the PSS/PDADMAC capsules being easily modulated upon annealing and salt-exposure.     

Direct Current Conductometry of Track Membranes

The electrical conductivity measured for a KCl solution in pores of poly(ethylene terephthalate) track membranes has been studied as depending on electrolyte concentration and pore diameter with the use of a direct-current source. The difference between the experimentally determined conductivity and the standard value has been shown to decrease with increasing electrolyte concentration and pore diameter. At the same time, its value is significantly lower than that determined by impedance spectroscopy. This result is related to a decrease in the contribution of a gel layer formed on the pore surface upon coming into the contact with the electrolyte to the electrical resistance of a membrane.     

Layer-by-layer electrostatic self-assembly of single-wall carbon nanotube polyelectrolytes

We have used anionic and cationic single-wall carbon nanotube polyelectrolytes (SWNT-PEs), prepared by the noncovalent adsorption of ionic naphthalene or pyrene derivatives on nanotube sidewalls, for the layer-by-layer self-assembly to prepare multilayers from carbon nanotubes with polycations, such as poly(diallyldimethylammonium) or poly(allylamine hydrochloride) (PDADMA or PAH, respectively), and polyanions (poly(styrenesulfonate), PSS). This is a general and powerful technique for the fabrication of thin carbon nanotube films of arbitrary composition and architecture and allows also an easy preparation of all-SWNT (SWNT/SWNT) multilayers. The multilayers were characterized with vis-near-IR spectroscopy, X-ray photoelectron spectroscopy (XPS), surface plasmon resonance (SPR) measurements, atomic force microscopy (AFM), and imaging ellipsometry. The charge compensation in multilayers is mainly intrinsic, which shows the electrostatic nature of the self-assembly process. The multilayer growth is linear after the initial layers, and in SWNT/polyelectrolyte films it can be greatly accelerated by increasing the ionic strength in the SWNT solution. However, SWNT/SWNT multilayers are much more inert to the effect of added electrolyte. In SWNT/SWNT multilayers, the adsorption results in the deposition of 1-3 theoretical nanotube monolayers per adsorbed layer, whereas the nominal SWNT layer thickness is 2-3 times higher in SWNT/polyelectrolyte films prepared with added electrolyte. AFM images show that the multilayers contain a random network of nanotube bundles lying on the surface. Flexible polyelectrolytes (e.g., PDADMA, PSS) probably surround the nanotubes and bind them together. On macroscopic scale, the surface roughness of the multilayers depends on the components and increases with the film thickness.     

一种新型复合微孔聚合物电解质及其与锂离子电池负极相容性研究

以介孔分子筛SBA-15为造孔剂和填料, 研究出一种无需使用增塑剂制备复合微孔型聚合物电解质(SBA-15 CMPE)的新方法. 组装Li/SBA-15 CMPE/Li对称电池, 并利用电化学阻抗谱(EIS)技术研究了存放时间、循环伏安(CV)扫描、恒电流极化以及环境温度等对Li/SBA-15 CMPE界面性质的影响. 通过将成膜浆料直接浇铸在用水性粘合剂制备的中间相微球碳(MCMB)电极片上, 制备附有SBA-15 CMPE的一体化电极(MCMB/SBA-15 CMPE). 用该MCMB/SBA-15 CMPE所组装的三电极模拟电池具有良好的循环性能, EIS研究揭示了其首次阴极极化过程中碳电极上SEI膜的形成、生长和稳定的过程.     

聚(丙烯腈-甲氧基聚乙二醇单丙烯酸酯-丙烯酸锂)的制备与表征

采用乳液聚合方法制备了锂离子电池凝胶电解质用丙烯腈-甲氧基聚乙二醇(350)单丙烯酸酯-丙烯酸锂共聚物. 利用红外光谱(IR), 差示扫描量热法(DSC)对共聚物结构进行了表征. 利用倒相法制备了共聚物微孔膜, 使聚(丙烯腈-甲氧基聚乙二醇(350)单丙烯酸酯)共聚物的溶解性能得到了显著提高, 同时, 还改善了膜的收缩性. 采用交流阻抗方法测试了凝胶电解质膜在室温下的电导率, 结果表明, 该凝胶电解质具有较高的离子电导率, 能满足现有锂离子电池使用要求.     

Effect of acid-base equilibria on the donnan potential of layer-by-layer redox polyelectrolyte multilayers

In polymer films carrying an excess of fixed charge the electrostatic penalty to bring ions of same charge from the bathing electrolyte into the film sets a membrane potential (Donnan Potential) across the film-electrolyte interface. This potential is responsible for the ionic permselectivity observed in polyelectrolyte membranes. We have used electrochemical measurements to probe the dependence of the Donnan potential on the acid-base equilibrium in layer-by-layer self-assembled polyelectrolyte multilayers. The voltammperogram peak position of the Os(III)/Os(II) couple in self-assembled polyelectrolyte multilayers comprised of poly(allylamine) derivatized with Os(bpy)(2)PyCl+ and poly(vinylsulfonate) was recorded in solutions of increasing ionic strength for different assembly and testing solution pH. Protonation-deprotonation of the weak redox poly(allylamine) changes the fixed charge population in the as prepared (intrinsic) self-assembled redox polyelectrolyte multilayers. For films assembled in solutions of pH higher than the test solution pH, the Donnan plots (E(app) vs log C) exhibit a negative slope (anionic exchanger) while for films assembled at lower pH than that of the test solution positive slopes (cationic exchanger) are apparent. The ion exchange mechanism has been supported by complementary electrochemical quartz crystal microbalance. X-ray photoelectron spectroscopy and infrared reflection-absorption spectroscopy experiments demonstrated that the as prepared films have a memory effect on their protonation state during assembly, which leads to the observed dependence of the Donnan potential on the adsorption pH.     

Effect of temperature on the buildup of polyelectrolyte multilayers

The effect of temperature on the buildup of polyelectrolyte multilayers consisting of poly(styrenesulfonate) (PSS), poly(diallyldimethylammonium) (PDADMA), and poly(allylamine) (PAH) was studied by using a quartz crystal microbalance. The increase of temperature in the deposition process was shown to have a considerable effect on the rate of the layer-by-layer buildup. The effect of temperature on the PDADMA/PSS deposition was found to be stronger than on the PAH/PSS deposition. The increasing temperature was found to extend the exponential buildup regime in all of the studied systems. A buildup model was created to simulate the buildup and to explain the effect of temperature. The model is based on the assumption that each deposition step leads to a quasi-equilibrium between the concentration of the polymer repeating unit in solution and the composition of the layer. According to the model, the layer-by-layer buildup is inherently exponential, becoming linear whenever diffusion is not fast enough to carry the polymer within the entire thickness of the film. This buildup model is discussed jointly with the earlier published three-zone model of the polyelectrolyte multilayers. The rate of the buildup is characterized by growth exponent beta. The temperature dependence of the growth exponent is discussed in connection with the thermodynamic parameters of the deposition.     

含水的凝胶电解质电化学特性及其在锂水电池中的初试

应用交流阻抗谱研究以聚甲基丙烯酸＿聚甲基丙烯酸锂＿甘油(GPE)作为锂水电池正极的体系,根据等效电路计算,发现升高温度和增加水含量均可提高体系的电导率.该体系导电过程类似于聚合物浓溶液,水分能降低聚合物的玻璃化温度,电解过程相当于电解水,分解电压1.50V.使用GPE组装室温全固态锂水电池,测定了该电池在恒负载(5.2kΩ)下放电曲线,发现当以石墨正极作集电极时,该电池能持续放电2h.使放电电压和放电电流下降的因素是:锂与GPE内水分反应生成的膜逐渐增厚,正极反应生成氢气,GPE内水份的扩散速率.     

Temperature Response of PNIPAM Derivatives at Planar Surfaces: Comparison between Polyelectrolyte Multilayers and Adsorbed Microgels

Two strategies for the design of thermosensitive coatings based on poly‐N‐isopropyl acrylamide (PNIPAM) derivatives are presented: 1) polyelectrolyte multilayers containing a diblock copolymer with a large PNIPAM block and 2) adsorption of PNIPAM microgels. The multilayers show only a small but irreversible response to the increase of outer temperature due to the strong interdigitation between the charged part and the temperature‐sensitive block, while the adsorbed microgels show a pronounced and reversible response. It will be shown that the microgel number density can be easily controlled at the substrate. The swelling and shrinking of two extremes in density are characterized: densely packed microgels, which are considered as a film, and individual microgels, which are able to swell and shrink also lateral to the surface.     

Preparation and the investigation of its electrochemical and photoluminescent characteristics of organic-inorganic hybrid multilayers containing europium-substituted heteropolytungstate

Photoluminescent multilayers were fabricated by layer-by-layer deposition between europium-substituted heteropolytungstate K₁₃[Eu(SiW₁₁O₃₉)₂]·28H₂O (denoted ESW) and a cationic polymer of quaternized poly(4-vinylpyridine) partially complexed with osmium bis(2,2′-bipyridine) (denoted as QPVP-Os) on glassy carbon and quartz substrates. The resulting photoluminescent organic-inorganic hybrid multilayers were characterized by electrochemical impedance spectroscopy, UV-Vis absorption spectrometry, cyclic voltammetry and photoluminescence spectra. Electrochemical impedance spectroscopy, UV-Vis absorption spectrometry and cyclic voltammetry results demonstrated that the multilayers were regular growth each layer adsorption. The photoluminescent properties of the films at room temperature were investigated to show the characteristic Eu³⁺ emission pattern of ⁵D₀→⁷F_j.     

Preparation and characterization of pva based solid polymer electrolytes for electrochemical cell applications

Solid polymer electrolyte films containing poly(vinyl alcohol) (PVA) and magnesium nitrate (Mg(NO3)2) were prepared by solution casting technique and characterized by using XRD, FTIR, DSC and AC impedance spectroscopic analysis. The amorphous nature of the polymer electrolyte films has been confirmed by XRD. The complex formation between PVA and Mg salt has been confirmed by FTIR. The glass transition temperature decreases with increasing the Mg salt concentration. The AC impedance studies are performed to evaluate the ionic conductivity of the polymer electrolyte films in the range of 303 383 K, and the temperature dependence seems to obey the Arrhenius behavior. Transport number measurements show that the charge transport is mainly due to ions. Electrochemical cell of configuration Mg/(PVA + Mg(NO3)2) (70:30)/(I2 + C + electrolyte) has been fabricated. The discharge characteristics of the cell were studied for a constant load of 100 kΩ.     

Design and preparation of a novel temperature-responsive ionic gel. 3. Valence selective control of transport modes of ions in response to temperature

We propose a novel model dialysis system that can valence-selectively control the transport modes of ions in response to temperature change. In a dialysis system consisting of an anionic gel membrane and mixed solutions containing a driving electrolyte and electrolytes with uni-, bi-, and trivalent cations, the dependence of the charge density of the gel and the valence of the ions on the transport modes of the ions through the gel membrane was investigated by computer simulations. The simulations show that the system has four transport types in the transport modes of the cations according to their valence [downhill (transport along their own concentration gradient in the system) and uphill (transport against their own concentration gradient)] in response to the charge density changes: (A) downhill transport of all the cations; (B) uphill transport of trivalent cations, downhill transport of the other cations; (C) uphill transport of bi- and trivalent cations, downhill transport of univalent cations; and (D) uphill transport of all the cations except for the driving cations. To examine the prediction of the simulations, a temperature-responsive anionic gel membrane was prepared from a modified poly(vinyl alcohol) (PVA) containing 2 mol % of sulfonic acid groups and another modified PVA prepared by in situ polymerization of N-isopropylacrylamide in a PVA solution. Permeation experiments in a dialysis system consisting of the membrane and mixed electrolyte solutions of NaCl, LiCl, CaCl2, and LaCl3 indicate that the system valence-selectively controls the transport modes of the cations in response to temperature change as predicted in our simulations.     

High temperature all solid state supercapacitor based on multi-walled carbon nanotubes and poly[2,5 benzimidazole]

Supercapacitor containing multi-walled carbon nanotubes (MWCNT) as the electrode material and phosphoric acid-doped poly[2,5 benzimidazole] (ABPBI) as the solid electrolyte and separator membrane has been investigated in a wide temperature range. Supercapacitors with different solid electrolyte concentrations have been fabricated and evaluated for their electrochemical performance. Specific capacitance of supercapacitors at room temperature was found to increase after the first heating cycle. Supercapacitor containing 10?wt.% of solid electrolyte in the electrode shows higher specific capacitance than the supercapacitor with liquid electrolyte. Cyclic voltammetry analysis of supercapacitors indicates high rate capability. The linear increase in the specific capacitance with temperature implies that capacitance is predominantly due to electric double layer. Electrochemical impedance analysis indicates that the mass capacitance and Warburg parameter increase with temperature, while solution resistance and leakage resistance decrease with temperature. The complex capacitance of the supercapacitors shows that both real and loss capacitances increase with temperature. The phase angle of supercapacitors is found to be around 85.2?±?1° at room temperature and it decreases with temperature. Galvanostatic charge–discharge cycling exhibits almost constant specific capacitance of 28?F?g^?1 at room temperature. However, it increases sharply and then attains stable value of 52?F?g^?1 during cycling at 100?°C. The increase in specific capacitance has been attributed to increase in surface area of the carbon nanotube (CNT), due to activation by phosphoric acid and diffusion of free phosphoric acid into the central canal of MWCNT.     

Influence of salt and rinsing protocol on the structure of PAH/PSS polyelectrolyte multilayers

A quartz crystal microbalance (QCM) and dual polarization interferometry (DPI) have been utilized to study how the structure of poly(allylamine hydrochloride) (PAH)/poly(styrene sulfonate) (PSS) multilayers is affected by the rinsing method (i.e., the termination of polyelectrolyte adsorption). The effect of the type of counterions used in the deposition solution was also investigated, and the polyelectrolyte multilayers were formed in a 0.5 M electrolyte solution (NaCl and KBr). From the measurements, it was observed that thicker layers were obtained when using KBr in the deposition solution than when using NaCl. Three different rinsing protocols have been studied: (i) the same electrolyte solution as used during multilayer formation, (ii) pure water, and (iii) first a salt solution (0.5 M) and then pure water. When the multilayer with PAH as the outermost layer was exposed to pure water, an interesting phenomenon was discovered: a large change in the energy dissipation was measured with the QCM. This could be attributed to the swelling of the layer, and from both QCM and DPI it is obvious that only the outermost PAH layer swells (to a thickness of 25-30 nm) because of a decrease in ionic strength and hence an increase in intra- and interchain repulsion, whereas the underlying layers retain a very rigid and compact structure with a low water content. Interestingly, the outermost PAH layer seems to obtain very similar thicknesses in water independent of the electrolyte used for the multilayer buildup. Another interesting aspect was that the measured thickness with the DPI evaluated by a single-layer model did not correlate with the estimated thickness from the model calculations performed on the QCM-D data. Thus, we applied a two-layer model to evaluate the DPI data and the results were in excellent agreement with the QCM-D results. To our knowledge, this evaluation of DPI data has not been done previously.     

The Effect of Supporting Electrolyte Concentration on Zinc Electrodeposition Kinetics from Methimazole Solutions

The kinetic parameters of Zn²⁺ ion electroreduction in sodium perchlorate used as the supporting electrolyte on the mercury electrode in the presence of methimazole were determined using electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and DC polarography. The two‐stage nature of this process was demonstrated. Both steps are catalysed by a methimazole. The size of the acceleration effect depends on the concentrations of methimazole and the supporting electrolyte. The acceleration of the electrode process involves the formation of active complexes between the depolarizer ions and methimazole on the electrode surface. These complexes facilitate the exchange of charge between the electrode and zinc ions during electroreduction process. The change of the hydrating sphere of the zinc ion is also important here. This in turn depends on its oxidation state and the concentration of the supporting electrolyte.