Indirect amperometric detection of underivatized amino acids in microcolumn liquid chromatography with carbon film based ring-disk electrodes

An indirect amperometric detection of underivatized amino acids has been developed using a carbon film based ring-disk electrode (CFBRDE) in microcolumn liquid chromatography (LC). Bromide present in the mobile phase could be efficiently oxidized to bromine at the upstream (disk) electrode, and was subsequently detected at the downstream (ring) electrode. Most of the underivatized amino acids that are electroinactive under conventional amperometric conditions react rapidly with the electrogenerated bromine, the concentration of amino acids can therefore be indirectly determined by continuously monitoring the reduction current of bromine. The signal monitored at the downstream electrode was largely dependent on the bromide concentration in the mobile phase. Under optimized conditions, the response linearly increased with the concentration for most of the amino acids over a concentration range of 1-100 microM, with a correlation coefficient of 0.990-0.993. The detection limits for most of the amino acids were below 1 microM (0.2 pmol). It was demonstrated that detection with a ring-disk electrode offers the advantages of achieving a much higher collection efficiency caused by a decrease in flow rate in the microcolumn LC.     

An integrated electrochemical capillary liquid chromatography-dual microelectrode system for bromine based reaction detection

Amperometric reaction detection of model peptides containing either a thiol or disulfide was successfully achieved with a novel coupled capillary liquid chromatography-dual microelectrode system. Detection is facilitated via dual platinum wire electrodes fabricated directly on a liquid chromatography capillary column. The detection strategy is based on the electrogeneration of bromine at the upstream working electrode followed by reduction of the bromine to bromide at the downstream working electrode. When bromine reacts with analyte eluting from the capillary column, the amount of bromine that reaches the downstream electrode decreases. As a result, the current at the downstream electrode will decrease in proportion to the amount of analyte eluting from the capillary column. Glutathione, glutathione disulfide, alpha-TGF and oxytocin were used to characterize the system and to determine system parameters. The feasibility of the determination of disulfide containing peptides is demonstrated with glutathione disulfide, alpha-TGF and oxytocin.     

Square wave voltammetry for analytical determination of paracetamol using cobalt microparticles film modified platinum electrode

Cobalt microparticles (Co MPs) modified Pt electrode is simply and conveniently fabricated. The electrochemical properties of paracetamol (PCT) at the prepared modified electrode are investigated using cyclic voltammetry (CV) and square wave voltammetry (SWV) measurements. Based on these techniques, a sensitive and rapid electrochemical method is developed for the determination of PCT. The result indicates that the oxidation of PCT is strongly improved at the Co MPs/Pt electrode as compared with the bare Pt electrode, with relatively high sensitivity, stability and life time. The determination of PCT on the Co MPs/Pt with square wave voltammetry displays a high sensitivity of 101 μA/mM and a low detection limit of 0.42 μM (S/N = 3) in the range (0.5–100 μM). The sensitivity of the modified electrode for the detection of PCT is almost 17 times greater than on the bare Pt electrode. The proposed method is successfully applied to the PCT determination in tablets.     

Improved determination of taurine by high-performance anion-exchange chromatography with integrated pulsed amperometric detection (HPAEC-IPAD)

The advantages of the high selectivity of high-performance anion-exchange chromatography (HPAEC) and the sensitive response of taurine at a gold electrode with integrated pulsed amperometric detection (IPAD) have been combined, in order to establish a new analytical method for its determination in real matrices. Potential-time settings of the potential waveform were optimized in order to get the highest amperometric response. The separation of taurine in milk samples was achieved using an alkaline eluent (100 mM NaOH) containing 1 mM Ba(OAc)₂ and a column temperature of 15 °C. The inherent merits of using a barium-modified eluent, in terms of taurine separation and detection, are demonstrated. The enhancement in sensitivity under these experimental conditions makes it suitable for taurine determination in milk. Indeed, this method allows high recovery of taurine and satisfies the necessary requirements with respect to accuracy, repeatability and sensitivity with a detection limit of 50 nmol/L, which corresponds to 2.5 pmol. The taurine content in milk samples of some common mammals was evaluated, including human milk. In goats milk, the taurine content ranged from 46 to 91 mg/L, whereas human and buffalo milk samples exhibited an average content of 18 mg/L and 23 mg/L, respectively.     

Development of capillary electrophoresis methods for quantitative determination of taurine in vehicle system and biological media

CE methods have been developed for the determination of taurine in pharmaceutical formulation (microemulsion) and in biological media such as sweat. The CE system with end-column pulsed amperometric detection has been found to be an interesting method in comparison with UV and fluorescence detection for its simplicity and rapidity. A gold-disk electrode of 100 mm diameter was used as the working electrode. The effects of a field decoupler at the end of the capillary, separation voltage, injection and pressure times were investigated. A detection limit of 4 x 10(-5) mol/L was reached using integrated pulsed amperometric detection, a method successfully applied to taurine analysis of the biological samples such as sweat. For taurine analysis of oil-in-water microemulsion, fluorescence detector was the favored method, the detection limit of which was 4 x 10(-11) mol/L.     

Electrocatalytic Reduction of H2O2 and Oxygen on the Surface of Thionin Incorporated onto MWCNTs Modified Glassy Carbon Electrode: Application to Glucose Detection

A new H₂O₂ enzymeless sensor has been fabricated by incorporation of thionin onto multiwall carbon nanotubes (MWCNTs) modified glassy carbon electrode. First 50 μL of acetone solution containing dispersed MWCNTs was pipetted onto the surface of GC electrode, then, after solvent evaporations, the MWCNTs modified GC electrode was immersed into an aqueous solution of thionin (electroless deposition) for a short period of time <5–50 s. The adsorbed thin film of thionin was found to facilitate the reduction of hydrogen peroxide in the absence of peroxidase enzyme. Also the modified electrode shows excellent catalytic activity for oxygen reduction at reduced overpotential. The rotating modified electrode shows excellent analytical performance for amperometric determination of hydrogen peroxide, at reduced overpotentials. Typical calibration at ?0.3 V vs. reference electrode, Ag/AgCl/3 M KCl, shows a detection limit of 0.38 μM, a sensitivity of 11.5 nA/μM and a liner range from 20 μM to 3.0 mM of hydrogen peroxide. The glucose biosensor was fabricated by covering a thin film of sol–gel composite containing glucose oxides on the surface of thionin/MWCNTs modified GC electrode. The biosensor can be used successfully for selective detection of glucose based on the decreasing of cathodic peak current of oxygen. The detection limit, sensitivity and liner calibration rang were 1 μM, 18.3 μA/mM and 10 μM–6.0 mM, respectively. In addition biosensor can reach 90% of steady currents in about 3.0 s and interference effect of the electroactive existing species (ascorbic acid–uric acid and acetaminophen) is eliminated. The usefulness of biosensor for direct glucose quantification in human blood serum matrix is also discussed. This sensor can be used as an amperometric detector for monitoring oxidase based biosensors.     

Improvement of Pulse Amperometric Detection Integrated Automated Flow Injection Analysis of Ethylenethiourea Determination

Improvement of pulse amperometric detection (PAD) method is demonstrated in determination of ethylenethiourea (imidazolidine‐2‐thione, ETU). The anodic detection of ETU will produce polymeric film on an electrode leading to an inactive electrode surface. Here, the PAD method was used to remove the polymeric film formed on the electrode surface between ETU detection. Further, the scheme was integrated with automated flow injection analysis (AFIA) for determining ETU. The operational parameters of PAD in the AFIA system were discussed thoroughly. The analytical characteristics of the system were evaluated at optimum conditions. The linear range of calibration plot was between 20 to 300 μM (the correlative coefficient, r = 0.999) and the detection limit was 0.9 μM (S/N = 3). The relative standard deviations of detection of 50 μM ETU were 0.82% with and 9.07% without PAD scheme. The results indicate the system is a very promising tool for ETU determination. Finally, the matrix effects of two water samples that were collected from a campus and a farm show good recoveries of 92% and 96%.     

Simultaneous Determination of Carbohydrates and Amino Acids by Capillary Zone Electrophoresis with Constant Potential Amperometric Detection at a Copper Electrode

Capillary zone electrophoresis with end-column amperometric detection at a copper microdisk electrode (100 μm in diameter) was successfully applied for simultaneous determination of carbohydrates and amino acids. Under the separation voltage of 27 kV and the separation electrolyte of 80 mM NaOH in a 75 cm fused silica capillary (10 μm i.d. × 375 μmU o.d.), complete separation of a standard mixture containing 9 carbohydrates and 12 amino acids was achieved in less than 25 min. With the electrokinetical injection of 5.4 s at 27 kV and the detection potential of 0.62 V vs. Ag/AgCl, the detection limits (S/N = 3) were 0.22–0.65 ppm (1.2–1.9 μM) for carbohydrates and 0.31–6.5 ppm (2.3–39 μM) for amino acids, respectively. The calculated numbers of theoretical plates were between 41,000 and 190,000. The use of this method for analysis of carbohydrates and amino acids in a urine sample was demonstrated.     

Non-enzymatic electrochemical detection of glycerol on boron-doped diamond electrode

A non-enzymatic direct electrochemical glycerol detection method at a commercial boron-doped diamond (BDD) electrode in 0.1 M NaOH supporting electrolyte was developed. All the used electrochemical techniques proved useful features for the oxidation and direct amperometric determination of glycerol at a BDD electrode in 0.1 M NaOH aqueous solution. It was found that the direct electrooxidation of glycerol on the BDD electrode requires both adsorbed glycerol and hydroxyls at the electrode surface. Also, the sp(2) carbon did not allow enhancement of the glycerol oxidation process. The electronalytical sensitivity for the determination of glycerol at the BDD electrode ranged from 0.040 to 0.226 μA mM(-1) as a function of the technique used. The highest electroanalytical sensitivity for the determination of glycerol at the BDD electrode was reached in batch system amperometric quantification under stirring conditions. Performed recovery studies indicated that it is possible to determine glycerol in real samples, and the proposed batch system analysis-based methodology can be a valuable tool for practical glycerol analysis.     

Preparation of Pt/MWCNTs Catalyst by Taguchi Method for Electrooxidation of Nitrite

Abstract—The Pt nanoparticles-functionalized multiwall carbon nanotubes (f-MWCNTs) modified glassy carbon electrodes were used to study the electrooxidation of nitrite. Pt nanoparticles were electrodeposited on the f-MWCNTs modified glassy carbon (GC) electrode by applying a constant potential to the electrode for a specific time. By applying optimized conditions (using Minitab software), Pt/MWCNTs/GC electrode was prepared by immobilizing 40 μL of f-MWCNTs on the GC electrode and applying a potential of–0.20 V vs. Ag/AgCl for 120 s. The electrooxidation of nitrite was studied on the prepared electrode in 0.1 M KCl solution. The amperometric response of the prepared electrode linearly changes with the concentration of nitrite from 4.0 μM to 2.4 mM. The detection limit of the electrode was found to be 1.5 μM (S/N = 3) with a sensitivity of 28.7 μA/mM.     

Analysis of Triorganotin Compounds by High-Performance Liquid Chromatography with Reverse-Pulse Amperometric Detection

High-performance liquid chromatography (HPLC) coupled with the reverse-pulse amperometric (RPA) detection method has been developed for the analysis of triorganotin compounds in aqueous solutions. The major advantage of RPA vs. conventional amperometric detection is its ‘in situ’ elimination of interference from dissolved oxygen in the chromatographic eluent; therefore, no extra chemicals or apparatus are required for oxygen removal. With a Partisil-10 SCX column and an eluent of methanol/0.01 M sodium acetate buffer (70:30, pH 5.5), the four triorganotins, viz., trimethyl-, triethyl-, tripropyl-, and tributyltin, can be totally separated. Detection by RPA was performed with a static dropping mercury electrode with an initial potential of ?1.15 V and a final potential of +0.15 V. The absolute detection limit (S/N = 3) ranged from 12 ng of tributyltin (as tin) to 0.3 μg of trimethyltin (as tin). Applications of the method to the analysis of trace tributyltin in marine antifoulant leachate and sea water are described.     

Voltammetric Determinations of Thymol on an Electrode Modified by Coimmobilized Carboxylated Multiwalled Carbon Nanotubes and Surfactants

Thymol is oxidized at glassy carbon electrodes (GCEs) modified with coimmobilized carboxylated multiwalled carbon nanotubes (MWCNT-COOH) and surfactants of various nature in a Britton–Robinson buffer solution. The effect of the nature and concentration of surfactants in the composition of the electrode surface modifier on the amperometric response of thymol was evaluated. It was found that the best voltammetric characteristics are achieved in the case of an anionic 0.10 mM sodium dodecyl sulfate (SDS) (a decrease in oxidation potential by 50 mV and an increase in oxidation currents 2.2-fold in comparison with MWCNT-COOH/GCE). The electrooxidation of thymol at MWCNT-COOH–SDS/GCE proceeds irreversibly with the participation of one electron and one proton and is controlled by the adsorption of the analyte. The electrode response is linear in the ranges 0.500–17.0 and 17.0–150 μM of thymol with the limits of detection 0.14 μM and determination 0.48 μM. The developed method is tested on thymol-containing pharmaceutical preparations. The voltammetry data are compared with the results of an independent spectrophotometric determination.     

Simultaneous Determination of Ranitidine and Metronidazole at Glassy Carbon Electrode Modified with Single Wall Carbon Nanotubes

Single‐walled carbon nanotubes(SWCNTs) were dispersed into DMSO, and a SWCNTs‐film coated glassy carbon electrode was achieved via evaporating the solvent. The results indicated that CNT modified glassy carbon electrode exhibited efficiently electrocatalytic reduction for ranitidine and metronidazole with relatively high sensitivity, stability and life time. Under conditions of cyclic voltammetry, the potential for reduction of selected analytes is lowered by approximately 150 mV and current is enhanced significantly (7 times) in comparison to the bare glassy carbon electrode. The electrocatalytic behavior is further exploited as a sensitive detection scheme for these analytes determinations by hydrodynamic amperometry. Under optimized condition in amperometric method the concentration calibration range, detection limit and sensitivity were about, 0.1–200 μM, detection limit (S/N=3) 6.3×10^?8 mol L^?1 and sensitivity 40 nA/μM for metronidazole and 0.3–270 μM 7.73×10^?8 mol L^?1 and 25 nA/μM for ranitidine. In addition, the ability of the modified electrode for simultaneous determination of ranitidine and metronidazole was evaluated. The proposed method was successfully applied to ranitidine and metronidazole determination in tablets. The analytical performance of this sensor has been evaluated for detection of these analytes in serum as a real sample.     

Copper modified platinum electrode for amperometric detection of spectinomycin sulfate by anion-exchange chromatography

A La~(3+)-Cu/Pt modified electrode was fabricated by electrodepositing process in CuSO_4 solution by adding a small amount of lanthium compound,and it was employed for direct current(DC) amperometric detection of spectinomycin by anion-exchange chromatography.Without derivatization,this method can simultaneously determine the main component and impurities in spectinomycin pharmaceutical raw material.Ease of preparation,being applied in DC detection mode and good catalytic stability confirmed the interest...     

Platinum Nanoparticles/Poly(isoleucine) Modified Glassy Carbon Electrode for the Simultaneous Determination of Hydroquinone and Catechol

A new electrochemical sensor based on Poly(Isoleucine) modified glassy carbon electrode decorated with platinum nanoparticles (Pt/Poly(Isoleucine)/GCE) was developed for sensitive individual and simultaneous determination of hydroquinone (HQ) and catechol (CC). Scanning electron microscopy (SEM), Electrochemical impedance spectroscopy (EIS), Cyclic voltammetry (CV) and Differential pulse voltammetry (DPV) were performed in order to characterize the Pt/Poly(Isoleucine)/GCE nanocomposite. For simultaneous determination of HQ and CC, Pt/Poly(Isoleucine)/GCE showed wide linear range between the 0.01–100.0 μM. The detection limits were 0.006 μM for HQ and 0.005 μM for CC. The Pt/Poly(Isoleucine)/GC electrode exhibited good sensitivity and reliability in the simultaneous electroanalysis of two isomers in PBS of pH 7.5. The modified electrode was used to detect the isomers in naturel samples.     

离子色谱-脉冲安培电化学检测引流组织液中的妥布霉素

建立了一种离子色谱(IC)分离,脉冲安培电化学法(PAD)直接检测人体引流组织液中妥布霉素的分析方法.采用高交换容量阴离子交换柱和低浓度KOH在线淋洗分离,不需要采用衍生化和离子对-柱后加碱等实现分离,并可在短时间内完成妥布霉素的测定.采用本方法测定的妥布霉素线性范围为0.05～10 mg/L,线性相关系数为0.9997,保留时间、峰面积和峰高的相对标准偏差分别为0.14％,0.38％和0.81％,检出限为7.11 μg/L.本方法成功应用于骨髓炎患者引流组织液中妥布霉素的测定,样品实际加标回收率为100.8％.     

Pt Nanoparticle‐modified Carbon Fiber Microelectrode for Selective Electrochemical Sensing of Hydrogen Peroxide

We report a simple approach to the production of carbon fiber‐based amperometric microbiosensors for selective detection of hydrogen peroxide (H₂O₂), which was achieved by electrometallization of carbon fiber microelectrodes (CFMs) by electrodeposition of Pt nanoparticles. The Pt‐carbon hybrid sensing interface provided a sensitivity of 7711±587 μA ? mM^?1 ? cm^?2, a detection limit of 0.53±0.16 μM (S/N=3), a linear range of 0.8 μM–8.6 mM, and a response time of <2 sec. The morphologies of the Pt nanoparticle‐modified CFMs were characterized by scanning electron microscopy. To achieve selectivity, permseletive layers, polyphenylenediamine (PPD) and Nafion, were deposited resulting in exclusion of the anionic and cationic interferents, ascorbic acid and dopamine, respectively, at their physiologically relevant concentrations. The resultant sensors displayed a sensitivity to hydrogen peroxide of 1381±72 μA ? mM^?1 ? cm^?2, and a detection limit of 0.86±0.19 μM (S/N=3). This simple and rapid metallization method converts carbon fiber microelectrodes, which are readily accessible, to microscale Pt electrodes in 2 min, providing a platform for oxidase‐based amperometric biosensors with improved spatial resolution over more commonly used platinum electrode array microprobes.     

Amino oxidase amperometric biosensor for polyamines

An improved amino oxidase enzyme electrode has been constructed and applied to the determination of the amount of polyamines present in real samples. The electrode is based on the amperometric detection of H₂O₂ produced in the enzymatic oxidation of polyamines by amino oxidase. Amino oxidase from soybean seedlings, characterized by an extremely high activity for cadaverine and putrescine, was used. The enzyme was immobilized in an agarose matrix in the presence of glutaraldehyde and bovine serum albumin on the surface of a Pt electrode. Cadaverine, in concentrations between 0.5 and 500 μM, can be quantitatively determined by use of the amino oxidase electrode, the linear calibration range being 0.5–10 μM. The lower detection limit was 0.2 μM and the response time was 15 to 60 s. Putrescine showed similar behaviour. The maximum current response for cadaverine was 5.1 μA/cm², with an apparent Michaelis-Menten constant (K_m′) of 0.175 mM. The sensor response was stable for more than 32 hours of continuous operation at room temperature and, in the presence of fish or meat homogenates, no change in the signal-to-noise ratio was observed. The long-term stability, pH and temperature response of the biosensor has also been studied.     

Pt‐Pd Bimetallic Nanoparticles Decorated Nanoporous Graphene as a Catalytic Amplification Platform for Electrochemical Detection of Xanthine

The nanoporous graphene papers (NGPs) was prepared by the hard‐template method. The Pt−Pd modified NGPs hybrid was prepared by the self‐assembly method. Then a glassy carbon electrode (GCE) modified with Pt−Pd bimetallic nanoparticles‐functionalized nanoporous graphene composite has been prepared for the electrochemical determination of Xanthine (XA). The Pt−Pd/NGPs hybrid was characterized by transmission electron microscopy, scanning electron microscope and X‐ray diffraction. The electrochemical behavior of XA on Pt−Pd/NGPs/GCE was investigated by cyclic voltammetry and amperometric i‐t. The Pt−Pd/NGPs modified electrode exhibited remarkably electrocatalytic activity towards the oxidation reaction of XA in phosphate buffer solution (pH=5.5). Under the optimal conditions, the determination of XA was accomplished by using amperometric i‐t, the linear response range from 1.0×10⁻⁵∼1.2×10⁻⁴ M. The detection limit was 3.0×10⁻⁶ M (S/N=3). The proposed modified electrode showed good sensitivity, selectivity, and stability with applied to determine XA in human urine.     

Electropolymerized Manganese Tetraaminophthalocyanine Thin Films onto Platinum Ultramicroelectrode for the Electrochemical Detection of Peroxynitrite in Solution

Peroxynitrite, ONOO^? also so‐called PON, is a very powerful oxidant and cytotoxic agent produced in biological systems by the recombination of nitric oxide and superoxide anion radical. Most of the techniques for assaying PON (chemiluminescence, fluorescence, UV‐visible spectroscopy, immunochemistry and EPR ) use indirect methods relying on measurements of secondary species. We report in this study the calibration of a chemically modified Pt ultramicroelectrode by electropolymerized manganese tetraaminophthalocyanine film (MnTAPc) for the determination of PON in aqueous solution. The obtained result allows showing for the first time a real‐time calibration curve of the amperometric determination of stable PON in aqueous solution. The sensitivity of the sensor is 14.6 nA mM^?1 and its detection limit is 5 μM.