CMPO/[Cnmim][NTf2]体系对Eu3+和UO22+的萃取行为

讨论了辛基(苯基)-N,N-二异丁基胺甲酰基甲基氧化膦(CMPO)/1-烷基-3-甲基咪唑双(三氟甲烷磺酰)亚胺盐([C_nmim][NTf_2],n=2,8,12)萃取体系分别对硝酸溶液中的铕离子(Eu~(3+))和铀酰根离子(UO_2~(2+))的萃取行为。主要研究了硝酸浓度、接触时间、温度、CMPO浓度对CMPO/[C_nmim][NTf_2]体系萃取性能的影响,并选取CMPO/[C_2mim][NTf_2]体系对模拟高放废液中的镧锕元素进行了萃取分离。结果表明:随着离子液体侧链长度增长,萃取平衡时间逐渐延长;CMPO/[C3+2mim][NTf_2]体系对Eu的萃取是放热反应,萃取率随酸度增加而逐渐降低,对UO_2~(2+)则是吸热反应,萃取率随酸度增加而逐渐升高;通过机理研究,推测出对Eu~(3+)的萃取反应是离子交换,而对UO_2~(2+)的萃取反应则是中性配位;CMPO/[C_2mim][NTf_2]体系能有效的萃取模拟高放废液中的镧系、锕系元素,且在高酸下有一定的镧锕分离效果。     

CMPO/[Cnmim][NTf2]体系对Eu3+和UO22+的萃取行为

讨论了辛基(苯基)-N,N-二异丁基胺甲酰基甲基氧化膦(CMPO)/1-烷基-3-甲基咪唑双(三氟甲烷磺酰)亚胺盐([C_nmim][NTf₂],n=2,8,12)萃取体系分别对硝酸溶液中的铕离子(Eu³⁺)和铀酰根离子(UO₂²⁺)的萃取行为。主要研究了硝酸浓度、接触时间、温度、CMPO浓度对CMPO/[C_nmim][NTf₂]体系萃取性能的影响,并选取CMPO/[C2mim][NTf₂]体系对模拟高放废液中的镧锕元素进行了萃取分离。结果表明:随着离子液体侧链长度增长,萃取平衡时间逐渐延长;CMPO/[C2mim][NTf₂]体系对Eu³⁺的萃取是放热反应,萃取率随酸度增加而逐渐降低,对UO₂²⁺则是吸热反应,萃取率随酸度增加而逐渐升高;通过机理研究,推测出对Eu³⁺的萃取反应是离子交换,而对UO₂²⁺的萃取反应则是中性配位;CMPO/[C2mim][NTf₂]体系能有效的萃取模拟高放废液中的镧系、锕系元素,且在高酸下有一定的镧锕分离效果。     

Thermodynamic properties and polymorphism of 1-alkyl-3-methylimidazolium bis(triflamides)

Heat capacities in a range of temperatures of (5 to 370) K, enthalpies and temperatures of phase transitions for 1-ethyl-3-methylimidazolium bis(triflamide) ([C₂mim][NTf₂]) and 1-octyl-3-methylimidazolium bis(triflamide) ([C₈mim][NTf₂]) have been determined by adiabatic calorimetry. [C₂mim][NTf₂] has been found to form four crystalline phases with different fusion temperatures. Formation of the phases can be controlled by the temperature of annealing during crystallization. [C₈mim][NTf₂] forms three sequences of crystalline modifications, each including two polymorphs. Based on results of the measurements, thermodynamic functions for the compounds under study have been calculated.A heat-capacity anomaly near T = 230 K reported earlier for [C₄mim][NTf₂] and [C₆mim][NTf₂] have been found in some crystalline modifications of both the studied compounds. The position of the anomaly depends on the temperature of annealing of the crystals.     

γ辐照引发[Cnmim][NTf2]离子液体变色研究

1-烷基-3-甲基咪唑双三氟甲基磺酰胺型离子液体(C_nmim][NTf₂])被认为是最有希望用于核燃料循环中的分离试剂之一, 虽然其化学结构在辐照过程中变化不大, 但在受到γ辐照后会发生明显的变色, 因此有必要研究该类离子液体的变色原因. 本文以⁶⁰Co为辐照源, 系统研究了辐照后不同C(1)－烷基链长和咪唑环上C(2)位上的H被甲基取代后离子液体的紫外-可见(UV-Vis)吸收光谱行为, 并结合辐照后离子液体荧光光谱和质谱的变化, 分析了导致该类离子液体辐照后颜色加深的原因. 结果表明, 随着咪唑环上C(1)―烷基链长度和剂量增大, 离子液体颜色加深; 而C(2)位上的H被甲基取代后颜色明显变浅. 辐照后咪唑型离子液体的变色主要来自于辐照后产生的烷基侧链含双键的咪唑阳离子, 咪唑阳离子二聚体和含氟咪唑化合物. 此外, γ辐照引起咪唑阳离子易发生π-π堆积, 而聚集态含量增加也会引起颜色加深.     

Formation of metastable crystals of [C4mim][NTf2] and [C6mim][NTf2]

Heat capacities of crystalline 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide [C₄mim][NTf₂] and 1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide [C₆mim][NTf₂] in the range 80 K-T_fus were measured in an adiabatic calorimeter. Anomalies in the heat-capacity curves for the both compounds occurred near 240 K. Positions of the anomalies depended on thermal history of the samples. More stable crystals had higher heat capacities in the range 220-260 K. Below 200 K heat capacities of all the crystals of the same compound were indistinguishable.     

Ionic Fluids Containing Both Strongly and Weakly Interacting Ions of the Same Charge Have Unique Ionic and Chemical Environments as a Function of Ion Concentration

Liquid multi‐ion systems made by combining two or more salts can exhibit charge ordering and interactions not found in the parent salts, leading to new sets of properties. This is investigated herein by examining a liquid comprised of a single cation, 1‐ethyl‐3‐methylimidazolium ([C₂mim]⁺), and two anions with different properties, acetate ([OAc]^?) and bis(trifluoromethylsulfonyl)imide ([NTf₂]^?). NMR and IR spectroscopy indicate that the electrostatic interactions are quite different from those in either [C₂mim][OAc] or [C₂mim][NTf₂]. This is attributed to the ability of [OAc]^? to form complexes with the [C₂mim]⁺ ions at greater than 1:1 stoichiometries by drawing [C₂mim]⁺ ions away from the less basic [NTf₂]^? ions. Solubility studies with molecular solvents (ethyl acetate, water) and pharmaceuticals (ibuprofen, diphenhydramine) show nonlinear trends as a function of ion content, which suggests that solubility can be tuned through changes in the ionic compositions.     

PVT properties of imidazolium-, phosphonium-, pyridinium- and pyrrolidinium-based ionic liquids using critical point constants

Song and Mason equation of state (EOS) with a simple modification has been extended to modelling PVT properties of ionic liquids (ILs). The considered ILs are [C₁mim][MeSO4], [C₁mim][CH₃OC₂H₅SO₄], [C₁mim][(CH₃)₂PO₄], [C₂mim][MeSO4], [C₂mim][BF₄], [C₂mim][SCN], [C₂eim][NTf₂], [C₄mim][C(CN)₃], [C₄mim][CF₃SO₃], [C₄mim][SCN], [C₅mim][NTf₂], [C₈mim][NTf₂], [(C₆H₁₃)₃P(C₁₄H₂₉)][Cl], [(C₆H₁₃)₃P(C₁₄H₂₉)][NTf₂], [(C₆H₁₃)₃P(C₁₄H₂₉)][Ac], [C₃mpyr][NTf₂], [C₄mpyr][NTf₂] and [Py][C₂H₅OC₂H₄SO₄]. Three temperature-dependent parameters in the proposed EOS have been scaled as functions of reduced temperature with the use of the law of corresponding states. It is shown that the knowledge of just critical temperature and critical density is sufficient to predict the PVT properties of these ILs. The overall average absolute deviation of calculated densities from literature values for 1347 data points of 18 ILs was found to be 0.58%. The predicted density of ILs from proposed EOS has been compared with those obtained by other literature work. Moreover, we indicate that the Zeno line regularity can well be predicted by proposed model for ILs.     

Calorimetric Study on the Ion Pairing and Aggregation of 1-Ethyl-3-Methylimidazolium bis(trifluoromethylsulfonyl)amide ([C2mim][NTf2]) and Related Ionic Liquids in the Low-Dielectric Constant Solvent Chloroform

A calorimetric study of dissolution of the ionic liquids (ILs) 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)amide ([C₂mim][NTf₂]), 1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl)amide ([C₆mim][NTf₂]), and 1-hexyl-3-methylimidazolium tris(trifluoromethylsulfonyl)methide ([C₆mim][CTf₃]) into chloroform (CHCl₃) is presented with particular focus on [C₂mim][NTf₂]. The interpretation of the calorimetric data for [C₂mim][NTf₂] was aided by additional NMR self-diffusion measurements and viscosity measurements that through the Stokes–Einstein equation provided information about the average size of the species present. It is evident that the main equilibrium species are ion pairs and aggregates. An estimate for the enthalpy contribution from aggregate formation for [C₂mim][NTf₂] was found to be ?2.09 kJ per mol of added IL at 288.2 K and slightly decreasing in magnitude to ?1.11 kJ·mol^?1 at 318.2 K. While all three ILs release heat upon dissolution into CHCl₃, different temperature trends are observed demonstrating the fine balance of competing contributions from breaking IL interactions, cavity formation for the solutes to reside in, and the establishment of new solute–solvent interactions.     

Effect of Ionic Liquid Anion Type in the Performance of Solid Polymer Electrolytes Based on Poly(Vinylidene fluoride‐trifluoroethylene)

The effect of different anions within the ionic liquid in the characteristics of solid polymer electrolytes (SPEs) based on P(VDF‐TrFE) has been investigated. 1‐ethyl‐3‐methylimidazolium acetate, [C₂mim][OAc], 1‐ethyl‐3‐methylimidazolium triflate, [C₂mim][(CF₃SO₃)], 1‐ethyl‐3‐methylimidazolium lactate, [C₂mim][Lactate], 1‐ethyl‐3‐methylimidazolium thiocyanate, [C₂mim][SNC] and 1‐ethyl‐3‐methylimidazolium hydrogen sulfate [C₂mim][HSO₄] have been used in SPE prepared by solvent casting. The polymer phase, thermal and electrochemical properties of the SPE have been determined. The thermal and electrical properties of the SPEs strongly depend on the selected IL, as determined by their different interactions with the polymer matrix. The room temperature ionic conductivity increases in the following way for the different anions: [SNC]>[CF₃SO₃)]>[HSO₄]>[Lactate]>[OAc], which is mainly dependent on the viscosity of the ionic liquid.     

Investigations on the Physicochemical and Radiolytic Degradation Properties of Tri-<Emphasis Type="Italic">n</Emphasis>-butylphosphate–Ionic Liquid in the Presence of Nitric Acid

Tri-n-butylphosphate (TBP) in an ionic liquid (IL) has been proposed as a suitable alternative for the solvent extraction of actinides from nitric acid solutions. This paper reports the detailed investigations on the physicochemical and hydrodynamic properties of the solvent system containing TBP in 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([C₄mim][NTf₂]) IL. The properties such as density, viscosity, phase separation time (PST), etc., were measured for irradiated and unirradiated solvent phases composed of TBP, [C₄mim][NTf₂] and 1.1 mol·L^–1 TBP in [C₄mim][NTf₂]. The results are compared with the values obtained in acid-equilibrated IL phases. ATR–FTIR spectroscopy and dynamic light scattering measurement of the IL phase were employed to characterize the interactions among the IL, TBP and nitric acid medium, and the aggregate size of the adduct formed in the IL phase.     

Study of the Alkyl Chain Length on Laccase Stability and Enzymatic Kinetic with Imidazolium Ionic Liquids

The activity and stability of laccase and their kinetic mechanisms in water soluble ionic liquids (ILs): 1-butyl-3-methyl imidazolium chloride [C₄mim][Cl], 1-octyl-3-methyl imidazolium chloride [C₈mim][Cl], and 1-decyl-3-methyl imidazolium chloride [C₁₀mim][Cl] were investigated. The results show that an IL concentration up to 10% is satisfactory for initial laccase activity at pH 9.0. The laccase stability was well maintained in [C₄mim][Cl] IL when compared to the control. The inactivation of laccase increases with the length of the alkyl chain in the IL: [C₁₀mim][Cl] > [C₈mim][Cl] > [C₄mim][Cl]. The kinetic studies in the presence of ABTS as substrate allowed calculating the Michaelis–Menten parameters. Among the ILs, [C₄mim][Cl] was the suitable choice attending to laccase activity and stability. Alkyl chains in the ions of ILs have a deactivating effect on laccase, which increases strongly with the length of the alkyl chain.     

Study on the Conductivities of Pure and Aqueous Bromide-Based Ionic Liquids at Different Temperatures

Electrical conductivities were measured for the pure ionic liquids [C₆mim][Br] (1-hexyl-3-methylimidazolium bromide) and [C₈mim][Br] (1-octyl-3-methylimidazolium bromide) at 0.1 MPa from 293.15 to 333.15 K. Conductivity measurements were also made for the binary water + [C₆mim][Br] and water + [C₈mim][Br] systems and their ternary water + [C₆mim][Br] + [C₈mim][Br] system at 0.1 MPa and 293.15, 298.15, and 303.15 K. The conductivity data of the pure ionic liquids were correlated by the VFT (Vogel-Tamman-Fulcher) equation, and the fitting parameters and mean absolute deviations were determined. New explanations are presented for the molality-dependent behavior of the conductivity of the binary water + [C₆mim][Br] and water + [C₈mim][Br] systems. The generalized Young’s rule and the semi-ideal solution theory for conductivity were used to predict the conductivities of the ternary water + [C₆mim][Br] + [C₈mim][Br] system from the conductivities of its corresponding binary water + [C₆mim][Br] and water + [C₈mim][Br] subsystems. The predictions are in good agreement with the measured values.     

Solubility of high-value compounds in environmentally friendly solvents–liquid poly(ethylene glycol) and ionic liquids: Experimental study and thermodynamic analysis

In this work the (solid + liquid) equilibria (SLE) of the solution of sustainable solvents with five high-value compounds, thymol, ferulic acid, vanillic acid, caffeic acid and caffeine, was investigated. The sustainable solvents studied were liquid poly(ethylene glycol) of average molecular mass 200 and 400 – (PEG200 and PEG400), respectively as well as imidazolium ionic liquids with bistriflamide and triflate anions ([C₄mim][NTf₂] and [C₄mim][OTf]). The obtained SLE data were correlated using the semi-empirical equation proposed by Grant. The activity coefficients of the studied solutes were calculated. Based on these correlations and calculations as well as on the thermo-physical properties of the pure constituents, the SLE behavior of the studied solutions was analyzed and discussed.     

Abrasive Stripping Voltammetric Studies of Lignin and Lignin Model Compounds

Lignin is potentially a major renewable, nonfossil source of aromatic and cyclohexyl compounds. In this study, we have investigated the abrasive stripping voltammetry of lignin and four lignin model compounds in the room temperature ionic liquids (RTILs) [C₄mim][NTf₂], [N_6,2,2,2][NTf₂] and [C₄mim][OTf] (where [C₄mim]⁺=1‐butyl‐3‐methylimidazolium, [N_6,2,2,2]⁺=n‐hexyltriethylammonium, [NTf₂]^?=bis(trifluoromethanesulfonyl)imide and [OTf]^? =trifluoromethanesulfonate) on a gold macrodisk and in 0.1 M H₂SO₄ and 0.1 M NaOH on a boron‐doped diamond (BDD) macroelectrode, with the hope of using the voltammetry to fingerprint the functional groups within the lignin molecule. The use of RTILs on metal electrodes, or either acidic or basic media in combination with BDD electrodes allows solvent systems with wide electrochemical potential windows, useful for studying voltammetry which may be difficult to observe in systems where early breakdown of the solvent occurs.     

Separation of aromatic hydrocarbons from alkanes using ammonium ionic liquid C2NTf2 at T = 298.15 K

(Liquid + liquid) equilibrium data are presented for four ternary systems of an alkane, or aromatic compound and ethyl(2-hydroxyethyl)dimethylammonium bis{(trifluomethyl)sulfonyl}imide (C₂NTf₂) at 298.15 K: [hexane + benzene + C₂NTf₂], [hexane + p-xylene + C₂NTf₂], and [hexane, or octane + m-xylene + C₂NTf₂]. The separation of aromatic hydrocarbons (benzene, or p-xylene, or m-xylene) from aliphatic hydrocarbons (hexane, or octane) is investigated by extraction with the ammonium ionic liquid. Selectivities and distribution ratios are discussed for these mixtures at constant temperature. The data were analysed and compared to those previously reported for other ionic liquids and especially for the system {hexane + benzene + [EMIM][NTf₂]}. The nonrandom two liquid NRTL model was successfully used to correlate the experimental tie-lines and to calculate the phase compositions of the ternary systems.     

High performance electromechanical actuators based on ionic liquid/poly(vinylidene fluoride)

Due to the increasing need of low voltage actuators, independent from electrochemical processes, electroactive actuators based on poly(vinylidene fluoride) composites with 10, 25 and 40% of 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, [C₂mim] [NTf₂], ionic liquid are prepared by solvent casting and melting. We show that the charge structure of [C₂mim] [NTf₂] induces the complete piezoelectric β-phase crystallization of the PVDF within the composite and decreases its crystallinity fraction significantly. [C₂mim] [NTf₂] also works as a plasticizer of PVDF, reducing the elastic modulus down to 12% of the initial value. Moreover, the composites show significant displacement and bending under applied voltages of 2, 5 and 10 Vpp. The displacement and bending of the composite membranes are also evaluated as a function of [C₂mim] [NTf₂] content and sample thickness. Increasing amounts of ionic liquid result in larger deformations independently of the applied voltage.     

Selective extraction of Cs(I) using 1,3-[(2,4-diethylheptylethoxy)oxy]-2,4-crown-6-calix[4]arene in ionic liquid solvents and its application to the treatment of high-level liquid waste

To separate heat-generating Cs from high-level liquid waste (HLLW), the extraction of Cs(I) using 1,3-[(2,4-diethylheptylethoxy)oxy]-2,4-crown-6-calix[4]arene (calix[4]arene-R14) in combination with 1-alkyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide) ionic liquids ([C _n mim][NTf₂], where n?=?2, 4, and 6) was investigated. Under moderately acidic conditions, the calix[4]arene-R14/[C _n mim][NTf₂] system showed a higher extraction efficiency (E_Cs) than that exhibited by the conventional calix[4]arene-R14/dichloromethane system. All extraction processes reached equilibrium within 5 min. Slope analysis revealed that the Cs:calix[4]arene-R14 inclusion complex has a 1:1 stoichiometry. The extraction was found to be exothermic and influenced by the presence of Na(I). These extraction systems exhibited high efficiency and selectivity for Cs(I) in simulated HLLW.     

Ionic Liquid‐based Microchannels for Highly Sensitive and Fast Amperometric Detection of Toxic Gases

Ionic liquid (IL)‐based microchannels sensors have been fabricated and employed for the detection of toxic ammonia (NH₃) and hydrogen chloride (HCl) gases, with enhanced sensitivity and response times compared to conventional electrodes. Electrochemical techniques were employed to understand the behaviour of these highly toxic gases in two ionic liquids, [C₄mpyrr][NTf₂] and [C₂mim][NTf₂], on a gold modified microchannels electrode. The limits of detection (LODs) obtained in [C₄mpyrr][NTf₂] for NH₃ (3.7 ppm) and in [C₂mim][NTf₂] for HCl (3.6 ppm) were lower than the current Occupational Safety and Health Administration Permissible Exposure Limit (OSHA PEL) for the two gases (25 ppm for NH₃ and 5 ppm for HCl). The response time of the sensor is 15 s with a sensitivity of 143 nA ppm^?1 and 14 nA ppm^?1 for HCl and NH₃, respectively. These results demonstrate the superiority of IL‐based microchannels sensors for detecting toxic gases, when compared to commercially available sensors or traditional IL‐based sensor designs, where high sensitivity or fast response time is still a challenge.     

水热条件下金红石纳米晶在离子液体[C12mim]Cl中的制备

在室温离子液体1-十二烷基-3-甲基氯化咪唑([C12mim]Cl)中,通过水热法制备了具有单晶结构的金红石纳米材料。采用X射线衍射、扫描电镜和透射电镜对样品进行了表征,结果显示所得样品为纯金红石相,形貌呈棒状。扫描电镜和透射电镜图样显示金红石纳米棒的直径约为15 nm,长度在10～100 nm之间。高分辨投射电镜图样显示金红石纳米棒为单晶结构,并沿c轴方向生长。实验结果表明离子液体[C12mim]Cl中的Cl-有利于金红石相生成,[C12mim]+起到了模板剂的作用并提高了金红石纳米棒的结晶度。     

Investigation of the Role of Ionic Liquids in Tuning the p<Emphasis Type="Italic">K</Emphasis><Subscript>a</Subscript> Values of Some Anionic Indicators

The effect of imidazolium-based ionic liquids, ([C₁₂mim][Cl] and [C₈mim][Cl]), on the acid-base equilibria of two sulfonated indicators has been studied. The presence of ILs leads to decreased pK _a values because of the stronger electrostatic interaction of cationic ILs with the basic forms of the indicators with more negative charge. The longer alkyl side chain of [C₁₂mim][Cl] compared to [C₈mim][Cl] results in stronger hydrophobic interaction of this IL with the basic forms of the dyes leading to a more effective decrease in the pK _a values. Also, the transition points and transition intervals of the acid-base titration curves of the indicators were affected by the presence of ILs. It was found that the IL interaction with acid-base indicators also results in sharpening the acid-base titration curves of the indicators. From these observations, it is concluded that the presence of ILs can tune the pK _a values of indicators. All the experiments were performed spectrophotometrically and the results were obtained using curve fitting methods.