Preparation of YBCO film for microwave filter using a hybrid route

Pure (0 0 l)-textured CeO₂ buffer layers were deposited on single crystal r-plane Al₂O₃ (1–102) substrate by a hybrid process which was combined with magnetron sputtering for the seed layer and metal–organic deposition for the subsequent layer. Strongly c-axis oriented YBCO films were deposited on the CeO₂ buffered r-cut Al₂O₃ (1–102) substrates. Atomic force microscope and scanning electronic microscopy results show that the prepared buffers and YBCO films are relatively dense and smooth. The critical current of the YBCO films exceeds 1.5 MA/cm² at 77 K with the superconducting transition temperature of 90 K. The surface resistivity is as below as 14 μΩ at 1 GHz frequency. The results demonstrate that the hybrid route is a very promising method to prepare YBCO films for microwave application, which can combine the sputtering advantage for preparing of highly c-axis oriented CeO₂ buffer layers and the advantages of metal–organic deposition with rapid processing, low cost and easy preparation of large-area YBCO films.     

YBCO films buffered by pyrochlore Nd2Mo2O7 layer on YSZ substrates by chemical solution deposition

A chemical solution deposition process was used to grow epitaxial Nd₂Mo₂O₇ (NMO) buffer layers on YSZ substrates to produce YBa₂Cu₃O_7?δ (YBCO) coated conductors. The NMO precursor solution prepared using metal acetylacetonates was spin-coated onto single crystal YSZ substrate of 10 mm × 10 mm in size at 3000 rpm for 30 s and heat-treated at 1000 °C for 2 h in Ar after calcinated at 550 °C for 1 h. The YBCO film was deposited by TFA-MOD route on top of the NMO/YSZ architecture. The phase purity and the crystalline orientation of NMO and YBCO films were evaluated by X-ray diffraction (XRD). Scanning electron microscopy (SEM) and atomic force microscopy (AFM) were used to observe their microstructure and their surface roughness. The critical current density (J_c) of YBCO film on NMO/YSZ is 1.8 MA/cm² at 77 K in self-field, which indicates that the Nd₂Mo₂O₇ is a potential buffer for YBCO coated conductor.     

Epitaxial growth of Ce2Y2O7 buffer layers for YBa2Cu3O7−δ coated conductors using reel-to-reel DC reactive sputtering

Biaxially textured Ce₂Y₂O₇ (CYO) films were deposited on Ni–5at.%W (Ni–5W) tapes by a DC reactive sputtering technique in a reel-to-reel system. Subsequent YBa₂Cu₃O_7?δ (YBCO) films were prepared using pulsed laser deposition leading to a simplified coated conductor architecture of YBCO/CYO/Ni–5W. X-ray diffraction measurements revealed an epitaxial growth of the CYO buffer layer with a texture spread down to 2.2° and 4.7° for the out-of-plane and in-plane alignment, respectively. Microstructural investigations showed a dense, smooth and crack-free surface morphology for CYO film up to a thickness of 350 nm, implying an effective suppression of cracks due to the incorporation of Y in CeO₂. The superconducting transition temperature T_c of about 90 K with a narrow transition of 0.8 K and the inductively measured critical current density J_c of about 0.7 MA/cm² indicate the potential of the single CYO buffer layer.     

Stable barium compounds in YBa2Cu3Oy superconductors

The stability of various amounts of Ba₃Cu₃In₄O₁₂ (334) or BaTbO₃ (BTO) in a sintered YBa₂Cu₃O_y (YBCO) matrix was examined. Samples with added 334 or BTO exhibited critical temperatures (T_c) above 90 K for up to 20 vol.% addition and improved critical current densities (J_c) under a magnetic field. X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray (EDX) analysis indicated that 334 and BTO did not react with the YBCO matrix under the sintering conditions used. The normalized J_c under a magnetic field of 1 T reached a maximum at 14 vol.% of 334 addition and 20 vol.% BTO addition. YBCO thin films with added BTO showed a gradual decrease in the T_c with increasing BTO content. YBCO films with added 334 showed a constant T_c of 87 K up to a 334 content of 4 vol.%.     

Modified Lanthanum Zirconium Oxide buffer layers for low-cost,high performance YBCO coated conductors

The pyrochlore Lanthanum Zirconium Oxide, La₂Zr₂O₇ (LZO), has been developed as a potential replacement barrier layer in the standard RABiTS three-layer architecture of physical vapor deposited CeO₂ cap/YSZ barrier/Y₂O₃ seed on Ni–5%W metal tape. The main focus of this research is to ascertain whether: (i) we can further improve the barrier properties of LZO; (ii) we can modify the LZO cation ratio and still achieve a high level of performance; and (iii) it is possible to reduce the number of buffer layers. We report a systematic investigation of the LZO film growth with varying compositions of La:Zr ratio in the La₂O₃–ZrO₂ system. Using a metal–organic deposition (MOD) process, we have grown smooth, crack-free, epitaxial thin films of La_xZr_1?xO_y (x = 0.2–0.6) on standard Y₂O₃ buffered Ni–5W substrates in short lengths. Detailed XRD studies indicate that a single epitaxial LZO phase with only (0 0 1) texture can be achieved in a broad compositional range of x = 0.2–0.6 in La_xZr_1?xO_y. Both CeO₂ cap layers and MOD–YBCO films were grown epitaxially on these modified LZO barriers. High critical currents per unit width, I_c of 274–292 A/cm at 77 K and self-field were achieved for MOD–YBCO films grown on La_xZr_1?xO_y (x = 0.4–0.6) films. These results indicate that LZO films can be grown with a broad compositional range and still support high performance YBCO coated conductors. In addition, epitaxial MOD La_xZr_1?xO_y (x = 0.25) films were grown directly on biaxially textured Ni–3W substrates. About 3 μm thick YBCO films grown on a single MOD–LZO buffered Ni–3W substrates using pulsed laser deposition show a critical current density, J_c, of 0.55 MA/cm² (I_c of 169 A/cm) at 77 K and 0.01 T. This work holds promise for a route for producing simplified buffer architecture for RABiTS based YBCO coated conductors.     

Effect of air humidity on the microstructure and properties of large-area YBa2Cu3O7−x films by TFA-MOD process

Large-area YBa₂Cu₃O_7?x (YBCO) films had been successfully fabricated on LaAlO₃ (LAO) substrate by metalorganic deposition using trifluoroacetates (TFA-MOD) and the effect of air humidity on the structure and properties of YBCO films was systematically investigated. The precursor coating process was performed in the air humidity range of 70–40%. According to the X-ray diffraction (XRD) and scanning electron microscopy (SEM) images, the films prepared at high air humidity showed poor electrical performance due to large pores and impurity phases. In contrast, dense, homogeneous and epitaxially grown YBCO films prepared at low air humidity with the critical current densities of 3.8–5.0 MA cm^?2 at 77 K had been obtained.     

Aqueous polymer–nitrate solution deposition of YBCO films

High critical current density YBa₂Cu₃O_7?x (YBCO) films were prepared by solution deposition of aqueous non-fluorine precursors. Non-fluorine polymer-assisted deposition (PAD) processes utilizing rheology modifiers and chelating agents were used to produce 50 nm films with a critical current density (J_c) over 3 MA/cm² and 400 nm films with J_c > 1 MA/cm²_. T_c measurements indicated that films have T_c values near 90 K. The total heat treatment time to produce these high performance films was less than 4 h. Rheology modifiers such as polyvinyl alcohol (PVA) and hydroxyethyl cellulose (HEC) were used to increase the thickness of deposited films independent of the solution cation concentration. Chelating agents such as polyethylene glycol (PEG) and sucrose increased the barium ion solubility. Nitrate crystallization during deposition was controlled through rapid drying with vacuum and coating with hot solutions.     

Deposition of Gd2Zr2O7 single buffer layers with different thickness for YBa2Cu3O7−δ coated conductors on metallic substrates

A series of Gd₂Zr₂O₇ (GZO) single buffer layers with different thicknesses were epitaxially grown on highly textured Ni–5 at.% W tapes using pulsed laser deposition. These allow the subsequent growth of high-quality superconducting YBa₂Cu₃O_7?δ layers. The superconducting transition temperature T_c reaches a maximum value of 92.4 K as well as a narrow transition width of 0.8 K for the optimized GZO layer thickness. The inductive measurements show the critical current density as high as 1.2 MA/cm² at 77 K in self-field, indicating that a GZO single buffer layer is a suitable alternative for simplifying the second generation high T_c superconducting coated conductors architecture.     

High performance GdBa2Cu3O7−z film preparation by non-fluorine chemical solution deposition approach

Biaxially textured GdBa₂Cu₃O_7?z (GdBCO) films with T_c above 93 K have been prepared on (0 0 l) LaAlO₃ substrate by self-developed non-fluorine polymer-assisted chemical solution deposition (PA-CSD) approach. The GdBCO films show smooth and crack-free morphology. Many nanoscale particles with homogeneous distribution are observed in the GdBCO films, which have not been observed yet in the YBa₂Cu₃O_7?z (YBCO) films prepared by the same processing technique. Besides a high J_c (77 K, 0 T) of 2.28 MA/cm², the optimized GdBCO films show a better J_c–B behavior and an improved high-field J_c, compared to the YBCO films.     

Preparation of solution-based YBCO films with BaSnO3 particles

The YBCO films with BaSnO₃ (BSO) particles were prepared on LAO (0 0 1) substrates by metal organic deposition using trifluoroacetates (TFA-MOD) via introducing SnCl₄ powders into the YBCO precursor solution. It was found that with the increase of the SnCl₄ contents, the slower decomposition and higher temperature for nucleation during the reaction were requested compared to that of pure YBCO film. The YBCO films with different contents of Sn with dense surface and well c-alignment were obtained under optimized heat treatment, and the BaSnO₃ phases were detected by XRD analysis. Litter effect of BSO particles on the T_c and J_c values of YBCO films was found. All YBCO films with BSO particles had T_c values over 90 K and J_c values over 1 MA/cm². A significant enhancement of J_c was observed for YBCO films with BSO particles compared to that of pure YBCO film by the field dependence of J_c values. The best property was obtained for YBCO film with 6 mol.% Sn at 77 K under magnetic field. The results showed that the J_c value of YBCO film with 6 mol.% Sn was enhanced by a factor of 2 in 2 T, and over a factor of 10 beyond 4 T compared to that of pure YBCO film.     

Epitaxial growth of La2Zr2O7 buffer layers for YBa2Cu3O7−δ coated conductors on metallic substrates using pulsed laser deposition

In the present work, La₂Zr₂O₇ (LZO) buffer layers were deposited using pulsed laser deposition (PLD) on various metallic substrates including epitaxial pure Ni on a LaAlO₃ (LAO) substrate as well as highly textured Ni–5 at.%W tapes. It is shown that the LZO deposited on pure Ni-buffered LAO exhibits a mixed orientation while LZO on Ni–5 at.%W grows epitaxially. This difference may be explained by the existence of a sulphur superstructure on the surface of Ni–5 at.%W tapes, promoting the epitaxial (0 0 l) nucleation of seed layers. Highly textured YBa₂Cu₃O_7?δ layers were prepared either by using a single buffer layer of LZO or bilayer buffers of CeO₂/LZO on Ni–5 at.%W. The superconducting transition temperature (T_c) increases with the LZO thickness, reaching a value of 90 K with a very narrow transition width (1.5 K) for 240 nm thick LZO layers. Inductive J_c measurements at 77 K in self-field show a value of about 0.96 MA/cm² for the thickest LZO layers, which is comparable to the value observed on standard buffer architectures such as CeO₂/YSZ/Y₂O₃.     

Texture analysis of RF-sputtered CeO2 buffer layers and superconducting MOD-YBCO films

CeO₂ buffer layers were deposited on YSZ single-crystal substrates using an RF-sputtering method. The development of crystalline textures of sputtered CeO₂ films at different sputtering pressure and their effects on YBCO films, deposited by Metal Organic Deposition (MOD), were investigated. Both CeO₂ and subsequent YBCO films grew well epitaxially. The relative XRD peak intensities of CeO₂ (2 0 0) to substrate YSZ (2 0 0) increased with deposition pressure in the range of 3–5 mTorr and were inversely proportional to the θ–2θ scan FWHM values of CeO₂ (2 0 0). Also, the reaction layers of BaCeO₃ were thicker in the samples with lower CeO₂ (2 0 0) intensities and poor out-of-plane alignment when CeO₂ were deposited at the lower pressure of 3.3 mTorr. It is noted, however, that the superconducting layer grew well epitaxially on these BaCeO₃ layers, possibly due to the epitaxial relation between CeO₂ and YBCO. The superconducting critical currents of MOD-YBCO films showed an increasing tendency as both the Δ2θ (CeO₂) and BaCeO₃ peak intensities decreased.     

Reduced crystallization time of YBCO in a fluorine-free MOD process using uv-lamp irradiation

We have studied the crystallization time dependence of the epitaxial YBCO films (t = 0.8 μm) grown on CeO₂-buffered SrTiO₃ substrates by fluorine-free metal–organic deposition using uv-lamp irradiation (uv-MOD). As increasing the time (T₀) for heat treatment at the reaction temperature (760 °C) from 0 to 90 min, J_c and the YBCO 0 0 l XRD intensity are steeply increased and reach their maximum values at T₀ = 10 min. This suggests that the heat treatment required for YBCO crystallization is significantly shortened in uv-MOD compared to conventional all-pyrolytic F-free MOD processes, which consume T₀ = 90–150 min for crystallizing 0.4–0.5-μm-thick films. Scanning electron microscope measurement revealed a drastic change in surface morphology between T₀ = 8 and 10 min, showing a good correspondence to the J_c and XRD data which suggest that the epitaxial growth reaches the film surface at the very early stage in the heat treatment.     

Fluctuation induced magneto-conductivity studies in YBa2Cu3O7−δ + xBaZrO3 composite high-Tc superconductors

Fluctuations on the electrical conductivity of polycrystalline YBa₂Cu₃O_7?δ + xBaZrO₃ (x = 1.0, 2.5, 5.0 and 10.0 wt.%) superconductors were investigated from the resistivity vs. temperature data for zero field and 8 T (Tesla) external magnetic fields. Attempts have been made to identify the optimum inclusion of BaZrO₃ (BZO) in YBa₂Cu₃O_7?δ (YBCO) superconductors. The phase formation, texture and grain alignments were analyzed by XRD and SEM techniques. Then the effects of superconducting fluctuations on the electrical conductivity of granular composite superconductors were studied for zero field and 8 T external magnetic fields. Though inclusions of BZO sub-micron particles are not expected to influence superconducting order-parameter fluctuation (SCOPF) much, the transition from 2D to 3D of the order parameter in the mean-field region depends on the BZO content in the composites. It has been observed that BZO residing at the grain boundary of YBCO matrix influences the tailing region without having significant change in the mean-field critical temperature. In the present work, attention has been focused mostly in the experimental domain relatively above the T_c. It reveals that, 1 wt.% composite exhibits a better superconducting property in comparison with pure YBCO.     

Influence of Zr and Ce doping on electromagnetic properties of (Gd,Y)–Ba–Cu–O superconducting tapes fabricated by metal organic chemical vapor deposition

(Gd,Y)Ba₂Cu₃O_x tapes have been fabricated by metal organic chemical vapor deposition (MOCVD) with Zr-doping levels of 0–15 mol.% and Ce doping levels of 0–10 mol.% in 0.4 μm thick films. The critical current density (J_c) of Zr-doped samples at 77 K, 1 T applied in the orientation of H 6 c is found to increase with Zr content and shows a maximum at 7.5% Zr doping. The 7.5% Zr-doped sample exhibits a critical current density (J_c) of 0.95 MA/cm² at H 6 c which is more than 70% higher than the J_c of the undoped sample. The peak in J_c at H 6 c is 83% of that at H 6 a–b in the 7.5% Zr-doped sample which is more than twice as that in the undoped sample. Superconducting transition temperature (T_c) values as high as about 89 K have been achieved in samples even with 15% Zr and 10% Ce. Ce-doped samples with and without Ba compensation are found to exhibit substantially different J_c values as well as angular dependence characteristics.     

Superconductivity and thermal properties of sulphur doped FeTe with effect of oxygen post annealing

Here, we report the synthesis and characterization of sulphur-substituted iron telluride i.e. FeTe_1?xS_x; (x = 0–30 %) system and study the impact of low temperature oxygen (O₂) annealing as well. Rietveld analysis of room temperature X-ray diffraction (XRD) patterns shows that all the compounds are crystallized in a tetragonal structure (space group P4/nmm) and no secondary phases are observed. Lattice constants are decreased with increasing S concentration. The parent compound of the system i.e. FeTe does not exhibit superconductivity but shows an anomaly in the resistivity measurement at around 78 K, which corresponds to a structural phase transition. Heat capacity C_p(T) measurement also confirms the structural phase transition of FeTe compound. Superconductivity appears by S substitution; the onset of superconducting transition temperature is about 8 K for FeTe_0.75S_0.25 sample. Thermoelectric power measurements S(T) also shows the superconducting transition at around 7 K for FeTe_0.75S_0.25 sample. The upper critical fields H_c2(10%), H_c2(50%) and H_c2(90%) are estimated to be 400, 650 and 900 kOe respectively at 0 K by applying Ginzburg Landau (GL) equation. Interestingly, superconducting volume fraction is increased with low temperature (200 °C) O₂ annealing at normal pressure. Detailed investigations related to structural (XRD), transport [S(T), R(T)H], magnetization (AC and DC susceptibility) and thermal [C_p(T)] measurements for FeTe_1?xS:O₂ system are presented and discussed.     

Enhanced superconducting properties in epitaxial FeSe thin films with self-assembled Fe3O4 nanoparticles

In this paper we report epitaxial tetragonal iron selenide thin films grown on single crystal SrTiO₃ (STO) (0 0 1) and MgO (0 0 1) substrates by a pulsed laser deposition (PLD) technique. Deposition temperature and annealing process are found to be critical for achieving the tetragonal phase and the optimum superconducting properties of the films. The critical transition temperature of the thin films ranges from 2 K to 11.5 K depending on the deposition temperature and annealing condition. The samples with higher critical transition temperatures show better film crystallinity along with self-assembled Fe₃O₄ nanoparticles (～15 nm in average particle size) in the films according to both X-ray diffraction (XRD) and transmission electron microscopy (TEM) analysis. Besides the better crystallinity achieved in the films, the formation of Fe₃O₄ nanoparticles could assist the formation of the tetragonal FeSe phase and thus lead to the enhanced superconducting properties.     

Influence of fabrication processing on phase transition and electrical properties of 0.8Pb(Zr1/2Ti1/2)O3–0.2Pb(Ni1/3Nb2/3)O3 ceramics

The binary system of 0.8Pb(Zr_1/2Ti_1/2)O₃–0.2Pb(Ni_1/3Nb_2/3)O₃ ceramics were synthesized by conventional mixed oxide and columbite method. X-ray diffraction analysis demonstrated the coexistence of both the rhombohedral and tetragonal phases for the columbite prepared sample. Rhombohedral to tetragonal phase transition for columbite method was different compared with those of the mixed oxide method. The permittivity shows a shoulder at the rhombohedral to tetragonal phase transition temperature T_Rho–Tetra = 195 °C, and then a maximum permittivity (36,000 at 10 kHz) at the transition temperature T_m = 277 °C on ceramics prepared with the columbite method. However, piezoelectric coefficient (d₃₃) was measured to be 282 pC/N for the conventional method and higher than the columbite method. The results were related to the phase compositions and porosity of the ceramics.     

Effects of doping with nanoscale Co3O4 particles on the superconducting properties of powder-in-tube processed MgB2 tapes

Nanoscale Co₃O₄ particles were doped into MgB₂ tapes with the aim of developing superconducting wires with high-current-carrying capacity. Fe-sheathed MgB₂ tapes with a mono-core were prepared using the in situ powder-in-tube (PIT) process with the addition of 0.2–1.0 mol% Co₃O₄. The critical temperature decreased monotonically with an increasing amount of doped Co₃O₄ particles for all heat-treatment temperatures from 600 to 900 °C. However, the transport critical current density (J_c) at 4.2 K varied with the heat-treatment temperatures. The J_c values in magnetic fields ranging from 7 to 12 T decreased monotonically with increasing Co₃O₄ doping level for a heat-treatment temperature of 600 °C. In contrast, some improvements on the J_c values of the Co₃O₄ doped tapes were observed in the magnetic fields below 10 T for 700 and 800 °C. Furthermore, J_c values in all the fields measured increased as the Co₃O₄ doping level increase from 0 to 1 mol% for 900 °C. This heat-treatment temperature dependence of the J_c values could be explained in terms of the heat-treatment temperature dependence of the irreversibility field with Co₃O₄ doping.     

Geometry dependent resistivity behavior in mesoscopic Bi2Sr2CaCu2O8+δ single crystals

In order to investigate the interaction between Josephson vortices and pancake vortices in a layered Bi₂Sr₂CaCu₂O_8+δ superconductor, c-axis resistivity measurements were carried out on fabricated mesoscopic single crystals for two experimental geometries, when an applied high magnetic field of 14 T is perpendicular (B_ex⊥L) and parallel (B_ex∥L) to the width of sample. In the first case, the angular dependence of the resistance obtained near the ab-plane at T = 30 K exhibited hysteretic non-monotonic behavior with local maxima at θ = 0.6° away from the ab-plane and dips and spikes at θ = 0.2° marking a vortex lock-in transition. In the second geometry (B_ex∥L), instead of a local maximum, peculiar resistance shoulders were observed. At higher temperatures, hysteresis is reduced, while the vortex lock-in transition becomes considerably broader indicating the interaction of pancake and Josephson vortices.