Polyelectrolyte multilayers on wood fibers: influence of molecular weight on layer properties and mechanical properties of papers from treated fibers

This paper compares the influence of the molecular weight of polylelectrolytes forming polyelectrolyte multilayers (PEM) on wood fibers on adhesion and paper strength. Sheets were made from fibers treated with poly(allylamine hydrochloride) (PAH)/poly(acrylic acid) (PAA) of molecular mass 70,000 and 240,000, respectively, and of poly(dimethyldiallylammonium chloride) (PDADMAC)/poly(styrene sulfonate) (PSS) of molecular mass 30,000 and 80,000, respectively. The results were compared to what has recently been reported for PEM formation on fibers using a low-molecular-mass combination of PAH and PAA and a high-molecular-mass combination of PDADMAC/PSS. There was a less significant improvement in the case of the low-molecular-mass PDADMAC/PSS and the high-molecular-mass PAH/PAA. The adsorbed amounts of PAH and PDADMAC were also determined, showing a lower adsorbed amount of the low-molecular-mass PAH than of the high-molecular-mass PDADMAC. The amount of low-molecular-mass PDADMAC was similar to that found for high-molecular-mass PDADMAC/PSS. Individual fibers were partly treated and studied, showing a less significant decrease in wettability with low-molecular-mass PDADMAC/PSS than with the high-molecular-mass combination. The effect of the molecular weight on the adhesion was discussed in terms of the structure and wettability of the PEMs.     

Preparation and characterization of polymer composite multilayers on SiO2

Poly(diallyldimethylammonium chloride) (PDADMAC) and poly(sodium 4-styrenesulfonate) (PSS) have been consecutively adsorbed onto 1.5-microm charged silica (SiO2) particles. Time-dependent adsorption studies indicate that, due to the strong ionic charge of the dissociated polycation in water, adsorption is complete in less than 30 min. Indications of the maximum adsorption density, changes in surface charge, and stability of the layered particles are demonstrated through adsorption isotherms and electrophoretic mobility (EPM) measurements. Further stability of the PDADMAC layer is demonstrated through multiwashing with ultra pure deionized water. Preliminary desorption studies of the PSS layer also illustrate a stabilized two-layer system. Due to the nature of the electrostatic charges on the surface of the SiO2 core particles and both polyelectrolytes in aqueous media, the use of polyelectrolytes as layering elements serves as a model for the assembly of time-released drug delivery particle systems.     

Organic pigment particles coated with titania via sol-gel process

This paper presented a novel method for the organic pigment coated with titania to improve the weatherability and dispersion ability in waterborne system. The organic pigment was first orderly adsorbed by two kinds of electrolyte: poly(sodium 4-styrenesulfonate) (PSS) and poly(diallyldimethylammonium chloride) (PDADMAC), then coated by titania via sol-gel process from titanium n-butoxide (TBOT). The effects of the numbers of polyelectrolyte layer, water content, and TBOT content on the morphology, particle size, surface element composition, porosity and pore size, thermal stability, and UV shielding property of the organic pigment were systematically investigated. It was found that only two layers of electrolyte adsorption and one-step coating of titania could obviously enhance the UV shielding property even thermal stability of the organic pigment. The thickness of the titania layer could be easily tailored by TBOT content.     

Colloid stability of sodium dihexadecyl phosphate/poly(diallyldimethylammonium chloride) decorated latex

The colloid stability of supramolecular assemblies composed of the synthetic anionic lipid sodium dihexadecyl phosphate (DHP) on cationic poly(diallyldimethylammonium chloride) (PDDA) supported on polystyrene sulfate (PSS) microspheres was evaluated via turbidimetry kinetics, dynamic light scattering for particle sizing, zeta-potential analysis, and determination of DHP adsorption on PDDA-covered particles. At 0.05 g/L PDDA and 5 x 10(9) PSS particles/mL, PDDA did not induce significant particle flocculation and a vast majority of PDDA covered single particles were present in the dispersion so that this was the condition chosen for determining DHP concentration (C) effects on particle size and zeta-potentials. At 0.8 mM DHP, charge neutralization, maximal size, and visible precipitation indicated extensive flocculation and minimal colloid stability for the DHP/PDDA/PSS assembly. At 0.05 g L(-1) PDDA, isotherms of high affinity for DHP adsorption on PDDA-covered particles presented a plateau at a limiting adsorption of 135 x 10(19) DHP molecules adsorbed per square meter PSS which was well above bilayer deposition on a smooth particle surface. The polyelectrolyte layer on hydrophobic particles was swelled and fluffy yielding ca. 6 +/- 1.5 nm hydrodynamic thickness. Maximal and massive adsorption of DHP lipid onto this layer produced polydisperse DHP/PDDA/PSS colloidal particles with low colloid stability and which, at best, remained aggregated as doublets over a range of large lipid concentrations so that it was not possible to evaluate the mean total thickness for the deposited film. The assembly anionic lipid/cationic PDDA layer/polymeric particle was relatively stable as particle doublets only well above charge neutralization of the polyelectrolyte by the anionic lipid, at relatively large lipid concentrations (above 1 mM DHP) with charge neutralization leading to extensive particle aggregation.     

Thermal behavior of polyelectrolyte multilayer microcapsules. 1. The effect of odd and even layer number

The temperature-dependent behavior of hollow polyelectrolyte multilayer capsules consisting of poly(diallyldimethylammonium chloride) (PDADMAC) and poly(styrene sulfonate) (PSS) with a different number of layers was investigated in aqueous media using confocal laser scanning microscopy, scanning and transmission electron microscopy, atomic force microscopy, and elemental analysis. Capsules with an even number of layers exhibited a pronounced shrinking at elevated temperature resulting in a transition to a dense sphere, whereas capsules with an odd number of layers swelled during heating to 5-fold of their initial size followed by their rupture. This effect increases for odd layer numbers and decreases for even layer numbers with increasing layer number. According to elemental analysis, an excess of PDADMAC monomers exists within the multilayers of capsules with an odd number of layers leading to a repulsion between the positive charges, whereas shells with an even number of layers have a balanced ratio between the oppositely charged polyions, so that the temperature-dependent behavior is controlled by the different interactions between polyelectrolytes and the bulk water. At a certain temperature, the polyelectrolyte material softens thus facilitating any rearrangement. Besides incubation temperature, the duration of heating has an influence on the restructuring of the multilayers.     

Formation of polyelectrolyte multilayers on fibres: influence on wettability and fibre/fibre interaction

Polydimethyldiallylammonium chloride (PDADMAC) and polystyrene sulfonate (PSS) have been used to build-up polyelectrolyte multilayers (PEMs) on chemical soft wood fibres and on SiO2 at various electrolyte concentrations. Adsorption onto SiO2 was studied using a stagnation point adsorption reflectometer (SPAR), and the adsorbed amount of PDADMAC and PSS on the fibres was determined using nitrogen analysis and Sch?niger burning, respectively. The adsorption onto the two substrates was then compared. Paper testing showed that the tensile index (TI) increased by about 90% when 11 layers had been adsorbed, and that there was a correlation between the adsorbed amount and the increase in TI. It was also shown that the particular polymer present in the outermost layer significantly influenced the TI, and that PDADMAC produced a higher TI. A correlation between the adsorbed amount and the TI was also found. Individual fibres were partly treated with a PEM and analysed using a dynamic contact angle analyser (DCA) and environmental scanning electron microscopy (ESEM).     

胶体颗粒在聚电解质多层膜表面的可控组装

利用原子力显微镜和扫描电子显微镜研究了磺化聚苯乙烯胶体颗粒在由聚二甲基二烯丙基氯化铵和聚苯乙烯磺酸钠层状自组装而成的多层膜表面的组装.该组装受表面性质影响,通过对多层膜的最外层的组装条件或利用盐溶液对多层膜进行后处理可以控制胶体颗粒在膜表面的组装密度.     

Preparation of electrically conducting cellulose fibres utilizing polyelectrolyte multilayers of poly(3,4-ethylenedioxythiophene):poly(styrene sulphonate) and poly(allyl amine)

The primary goal with this work is to create electrically conductive cellulose fibres, this has been done to explore possible new applications for fibre based material. This research uses various methods to create polyelectrolyte multilayers (PEMs) on bleached softwood fibres and on SiO₂ model surfaces, by sequentially treating these materials with poly(3,4-ethylenedioxythiophene):poly(styrene sulphonate) (PEDOT:PSS) and poly(allyl amine) (PAH). Paper sheets were then produced from the PEM-modified pulp and evaluated in terms of tensile strength, adsorbed amount of polymer, and electrical conductivity. To evaluate the influence of fibre charge on the measured paper properties, pulps of two different initial fibre charge densities were prepared via carboxymethylation. Because of the bluish colour of PEDOT:PSS, the build-up of PEM could be easily followed, since the fibres grew increasingly darker blue throughout the modification sequence. The conductivity of the fibre network increased by 2−3 orders of magnitude when the pulp of a higher fibre charge density was used. This suggests that it is more important to create a fibrous network with a high fibre-fibre joint strength and a large total joined area in the sheet rather than to maximize the adsorbed amount of PEDOT:PSS. A difference in conductivity could also be noted depending on the polyelectrolyte adsorbed in the outer layer, PAH lowered the conductivity compared to PEDOT:PSS. Evaluating the mechanical properties revealed that the use of PEDOT:PSS reduces the tensile strength of the paper. When five double layers had been adsorbed onto the carboxymethylated sample in which PEDOT:PSS formed the outer layer, calculations indicated a 25% decrease in tensile strength compared to that of reference material without PEMs. ESEM studies indicate that PEM treatment produces a significantly changed and somewhat smoother fibre surface.     

Characterization of poly(ethylene imine) layers on mica by the streaming potential and particle deposition methods

Deposition kinetics of polystyrene latex (averaged particle size of 0.66 microm) on mica covered by poly(ethylene imine) (PEI), a cationic polyelectrolyte having an average molecular mass of 75,000 g mol(-1), was studied using the impinging-jet method. The hydrodynamic radius of PEI, determined by PCS measurements, was 5.3 nm. The electrophoretic mobility of PEI was measured as a function of pH for ionic strengths of 10(-3) and 10 (-2) M, which made it possible one to determine the amount of electrokinetic charge of the molecule and its zeta potential. Formation of the polyelectrolyte layer on mica was followed by measuring the streaming potential in the parallel-plate channel. From these measurements, the dependence of the apparent zeta potential of mica on the surface coverage of PEI was determined. The amount of adsorbed PEI on mica was calculated from the convective diffusion theory. These results were quantitatively interpreted in terms of the theoretical model postulating a particle-like adsorption mechanism for PEI with not too significant shape deformation upon adsorption. On the other hand, the Gouy-Chapman model postulating the adsorption in the form of flat disks was proved inappropriate. After the surface was fully characterized, particle deposition experiments were carried out with the aim of finding the correlation between the polymer coverage and the initial rate of latex particle deposition. In the range of small polyelectrolyte coverage, a monotonic relation between the polymer coverage and the initial deposition rate of particles, as well as the jamming coverage, was found. For Theta(PEI)>0.25, the initial particle deposition rate attained the value predicted from the convective diffusion theory for homogeneous surfaces. These results were interpreted theoretically by postulating that an effective immobilization of colloid particles occurred on local polyelectrolyte assemblages containing between two and three PEI molecules.     

Thermal behavior of polyelectrolyte multilayer microcapsules: 2. Insight into molecular mechanisms for the PDADMAC/PSS system

Polyelectrolyte multilayer capsules consisting of poly(diallyldimethylammonium chloride) (PDADMAC) and poly(styrene sulfonate) (PSS) were used as a model system to study the temperature-dependent behavior of polyelectrolyte multilayer films in aqueous media. Shells terminated with PSS shrink upon heating, whereas PDADMAC-terminated ones swell, independent of the nature of the first layer, as measured by means of confocal laser scanning microscopy (CLSM) and scanning electron microscopy (SEM). Elemental analysis shows that the initial exponential layer growth of the film leads to a nearly neutral overall charge in the first case or a high positive excess charge in the latter. Depending on this overall charge either surface tension, due to an unfavorable polymer-solvent interaction, or electrostatics dominates, resulting in a shrinkage or expansion of capsules, respectively. Thus, it is possible to swell temperature-shrunk capsules by coating them with an additional PDADMAC layer. Micro-DSC measurements prove that polyelectrolyte multilayers undergo a glass transition in water at which the wall material softens, allowing the rearrangements to occur. It is found that the thermal history has an influence on the temperature behavior of capsules, especially on those ones terminated with PDADMAC. Also, the molecular weight of the polyelectrolytes affects the rearrangement of capsules. The lower the molecular weight and thus the smaller the entanglement of chains, the easier polyelectrolytes can rearrange.     

Thermal transitions in and structures of dried polyelectrolytes and polyelectrolyte complexes

Dynamic mechanical analysis (DMA) was used to explore the thermomechanical properties of dried polyelectrolytes and polyelectrolyte complexes (PECs) with different thermal and humidity histories. Although differences in the amount of water remaining in polyelectrolytes and PECs were small for ambient versus dessicator storage, the properties of polyelectrolyte‐based materials were drastically different for different humidity histories. Glass transition temperatures (T_gs) of poly(diallyldimethylammonium chloride) (PDADMAC) were shown to vary by 100 °C, depending on humidity and thermal histories. These parameters also change glassy storage modulus values by 100%. Furthermore, we observe that dried PDADMAC is highly lossy. DMA of dried poly(styrene sulfonate) (PSS) was more complex and did not exhibit a glass transition in the tested range. DMA of a PEC of PDADMAC and PSS revealed a humidity history‐dependent water melt in the first heating cycle, as well as storage modulus values of dried and annealed PECs that only varied by 17–26% over a 275 °C temperature range. Based on these results, we report for the first time humidity history as controlling structure and properties of polyelectrolyte‐based materials. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 684–691     

High-flux nanofiltration membranes prepared by adsorption of multilayer polyelectrolyte membranes on polymeric supports

Layer-by-layer deposition of anionic and cationic polyelectrolytes readily converts polymeric ultrafiltration membranes into materials capable of nanofiltration. ATR-FTIR spectra confirm that layer-by-layer deposition occurs on the ultrafiltration substrates, and adsorption of as few as 2.5 bilayers of poly(styrenesulfonate) (PSS)/protonated poly(allylamine) (PAH) or 3.5 bilayers of PSS/poly(diallyldimethylammonium chloride) (PDADMAC) reduces the molecular weight cutoff of polyethersulfone ultrafiltration supports from 50 kDa to <500 Da. Deposition of multilayer polyelectrolyte films on 300 and 500 kDa membranes also decreases molecular weight cutoffs, but solute rejections are significantly lower when using these supports, suggesting that the polyelectrolyte films do not completely cover large (0.2-0.4 microm in diameter) pores. On the 50 kDa substrates, PSS/PDADMAC films containing 3.5 bilayers exhibit a 95% rejection of SO(4)(2-) and a chloride/sulfate selectivity of 27, whereas 4.5-bilayer PSS/PAH coatings show a glucose/raffinose selectivity of 100. Pure water flux for [PSS/PAH](3)PSS-coated membranes at 4.8 bar is 1.6 m(3)/(m(2)day), which is more than 2-fold higher than that through a commercial 500 Da membrane.     

Characterization of poly(3,4-ethylenedioxythiophene)/poly(styrene sulfonate) (PEDOT:PSS) adsorption on cellulosic materials

The interaction between poly(3,4-ethylene dioxythiophene) doped with poly(styrene sulfonate) (PEDOT:PSS) and cellulosic fibers was characterized in order to obtain further understanding of the conductivity properties of the modified cellulosic fiber material. Microcrystalline cellulose (MCC) was used as a model surface to study the adsorption behavior at various pH and salt concentrations, while samples of low-conductivity paper, normally used for the production of electrical insulation papers, were dipped into PEDOT:PSS dispersion and air-dried for X-ray photoelectron spectroscopy (XPS) studies. The results showed a strong interaction between the MCC and PEDOT:PSS, which implied a broad molecular distribution of the conducting polymer. With increasing pH, less amount of the conducting polymer was adsorbed whereas the amount adsorbed passed through a maximum value with varying salt concentration. Zeta potential measurement and polyelectrolyte titration were used to determine the surface charge of both suspended MCC particles and dispersed PEDOT:PSS at various pH levels and salt concentrations. Dip-coated paper samples exhibited two peaks in the S(2p) XPS spectra at 168–169 and 164–165 eV which correspond to the sulfur signals of sulfonate (in PSS) and in thiophene (in PEDOT), respectively. It was found that the PEDOT:PSS with a ratio of 1:2.5 was adsorbed more in the base paper than that with a ratio of 1:6. The PEDOT:PSS ratio on the surface of the cellulosic material was higher than that in the bulk liquid for all samples. The results indicated that PEDOT was preferentially adsorbed rather than PSS. The degree of washing of the conducting polymer did not significantly affect the PEDOT enhancement on the surface.     

A conductivity study and calorimetric analysis of dried poly(sodium 4-styrene sulfonate)/poly(diallyldimethylammonium chloride) polyelectrolyte complexes

Ionically cross-linked polyelectrolyte complexes (PECs) of anionic poly(sodium 4-styrene sulfonate) (PSS) and cationic poly(diallyldimethylammonium chloride) (PDADMAC), xPSS.(1-x)PDADMAC, with molar fractions x ranging from 0.30 to 0.70, were prepared and subsequently dried. The PEC samples were analyzed by differential scanning calorimetry, and the ionic conductivity sigmadc of the samples was measured as a function of temperature by means of impedance spectroscopy. The thermograms display an endothermic peak in the temperature range of 90-143 degrees C, which is attributed to a glass transition of the PEC. The glass transition temperature Tg has a symmetric x dependence with a minimum at x=0.50. The temperature dependence of sigmadcT is not affected by the glass transition. The ionic conductivity of the samples before drying is three orders of magnitude larger than sigmadc after drying; nevertheless, their activation enthalpies are identical. Arrhenius parameters obtained from the systematic study of several PEC compositions are discussed. The ionic conductivity of the PSS-rich samples is significantly higher than sigmadc of PDADMAC-rich samples. This implies a relatively high Na+ mobility as compared to Cl(-) mobility in PEC. In contrast to the symmetric x dependence of Tg, the conductivity of PEC increases and the activation enthalpy decreases with increasing x in the investigated composition range. A strong x dependence of sigmadc is observed for PSS-rich PEC, which is attributed to a significant variation in the mobility of the charge carriers.     

Super-stoichiometric charge neutralization in particle-polyelectrolyte systems

The adsorption of poly(vinylamine) (PVA) on poly(styrene sulfate) latex particles is studied, and its consequences on the charging behavior and suspension stability are investigated. The adsorption process is assessed by batch depletion experiments and time-resolved electrophoretic mobility measurements. The adsorption of PVA appears to be basically irreversible. The rate of adsorption decreases with decreasing polymer dose. At low polymer dose, the polymer coverage corresponds to the amount of the polyelectrolyte added, while at high polymer dose, the polymer coverage saturates the surface. Stability ratios are determined by dynamic light scattering, and strongly depend on the polymer dose and salt level. The aggregation is rapid near the isoelectric point (IEP), and it slows down when moving away from it. The charge neutralization is highly nonstoichiometric with charging ratios (CR) larger than unity, meaning that several charges on an adsorbed polyelectrolyte chain are necessary to neutralize a single charge on the particle surface. By comparing the IEP for particles and polyelectrolytes of different charge densities, we find a strong dependence of the CR on the mismatch between the average distances between individual charges on the surface and on the polyelectrolyte. A simple model is proposed to explain this trend.     

Unusual collapse of highly hydrated polyelectrolyte multilayers with the ionic strength

Highly hydrated polyelectrolyte multilayers (PEMs) were fabricated by “layer by layer” (LBL) assembly of poly (diallyl dimethyl ammonium chloride) (PDADMAC) and poly (sodium 4‐styrene sulfonate) (PSS) in 0.5 M NaCl. Both thickness and hydration of the film were determined in situ as the multilayer was assembled by means of the quartz crystal microbalance with dissipation (QCM‐D) and the Spectroscopic Ellipsometry techniques combined in a single device. For PEMs of 17 total layers in water, a final thickness of up to 300 nm and a hydration of 69% were measured. The response towards the ionic strength was then studied by means of QCM‐D. PEMs of 17 layers, with PDADMAC as last layer, shrunk dramatically and lost water when exposed to aqueous NaCl solutions of increasing concentration. Indeed, a thickness variation up to 100 nm and reduction in the 50% of the water content were observed when the PEM was exposed to 1 M NaCl. On the contrary, PEMs where PSS appears on top showed no measurable change upon the variation in the ionic strength. This brings the possibility to control the responsive character of the PEMs simply by selecting the last polyelectrolyte layer (PDADMAC or PSS) deposited. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Adsorption of poly(styrene sulfonate) of different molecular weights on alpha-alumina: effect of added sodium dodecyl sulfate

The adsorption of poly(styrene sulfonate), PSS, of different molecular weights (70,000, 500,000, and 1,000,000 mol/kg), from aqueous solutions on alpha-alumina has been investigated. PSS of the lower molecular weight adsorbs less than the others whose adsorption isotherms overlap. The adsorption is found to increase with increasing ionic strength of the solutions indicating that both electrostatic and non-electrostatic contributions are involved in the adsorption process. Upon addition of the anionic surfactant, sodium dodecyl sulfate, SDS, PSS is found to adsorb less the more SDS added. SDS is found to be preferentially adsorbed as shown both from the simultaneous adsorption of the components and also from the sequential adsorption process where SDS in all cases displaces preadsorbed PSS from the solid surface. The displacement of preadsorbed polyelectrolyte by surfactant is a very slow process and the displacement is less pronounced as the molecular mass of the polyelectrolyte increases indicating the fewer number of contact points to the surface. This is further underlined by the effect on the displacement of PSS by SDS upon increasing the ionic strength of the solutions.     

Multilayer polyelectrolyte films as nanofiltration membranes for separating monovalent and divalent cations

Alternating adsorption of polyanions and polycations on porous supports provides a convenient way to prepare ion-selective nanofiltration membranes. This work examines optimization of ultrathin, multilayer polyelectrolyte films for monovalent/divalent cation separations relevant to water softening. Membranes composed of five bilayers of poly(styrene sulfonate)/poly(allylamine hydrochloride) (PSS/PAH) on porous alumina supports allow a solution flux of 0.85 m³/(m² day) at 4.8 bar, and exhibit 95% rejection of MgCl₂ along with a Na⁺/Mg²⁺ selectivity of 22. Similar results were obtained in Na⁺/Ca²⁺ separations. PSS/poly(diallyl-dimethylammonium chloride) (PDADMAC) films permit higher fluxes than PSS/PAH systems due to the higher swelling of films containing PDADMAC, but the Mg²⁺ rejection by PSS/PDADMAC membranes is less than 45%. However, capping PSS/PDADMAC films with a bilayer of PSS/PAH yields Mg²⁺ rejections and Na⁺/Mg²⁺ selectivities that are typical of pure PSS/PAH membranes. Separation performance can be optimized through control over deposition conditions (pH and supporting electrolyte concentration) and the charge of the outer layer since Donnan exclusion is a major factor in monovalent/divalent cation selectivity. Streaming potential measurements demonstrate that the magnitude of positive surface charge increases with increasing concentrations of Mg²⁺ in solution or when the outer polycation layer is deposited from a solution of high ionic strength.     

Preparation and adsorption of refined polyelectrolyte complex nanoparticles

We report on bulk and surface properties of centrifuged nonstoichiometric polyelectrolyte complex (PEC) dispersions. PECs were prepared by mixing poly(diallyldimethylammonium chloride) (PDADMAC) and sodium poly(maleic acid-co-alpha-methylstyrene) (PMA-MS) at the monomolar mixing ratio of 0.6 and polymer concentration >/=1 mmol/l. Centrifugation of initial PEC dispersions revealed three phases: supernatant (SUP), coacervate (COAC), and an insoluble precipitate. Mass, turbidity, particle hydrodynamic radii (R(h)), and the titratable charge amount were determined for those phases. The turbid COAC phase consisted of 200-nm nanoparticles and carried 60% of the polymer mass and 20% of the titratable charge amount of the initial PEC dispersion. The SUP phase showed no turbidity and no such nanoparticles, but carried 80% of the initial titratable charge amount, presumably caused by excess polycations. Furthermore, linear dependences of turbidity and R(h) on COAC concentration was observed. COAC adsorption was studied at polyelectrolyte multilayer (PEM) modified silicon surfaces in dependence on both adsorption time and concentration using attenuated total-reflection-Fourier transform infrared (ATR-FTIR) spectroscopy. The adsorption data were fitted by the simple Langmuir model. Comparison of COAC particles and polystyrene latices revealed similar adsorption features. SEM and AFM measurements resulted in hemispherically shaped adsorbed COAC particles with coverages >/=25%, whose calculated volumes correlated well with those in dispersion obtained by PCS.     

Polyelectrolyte adsorption and stabilization of silica-suspensions

The adsorption of cationic polyelectrolytes on colloidal silica-particles is investigated. The polyelectrolytes poly(diallyl-dimethyl-ammoniumchloride) PDADMAC of different molar mass have been used. The adsorbed amount is influenced by the ionic strength and pH of the suspension and the molar mass of the macromolecule. The adsorption determines the zetapotential of the covered particles. The electrostatic interaction between the particles as well as the structure of the adsorbed polyelectrolytes play an important role in the stabilization and flocculation behaviour of the polyelectrolyte covered suspensions.