Effects of lithium excess amount on the microstructure and electrochemical properties of LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode material

Spinel LiNi_0.5Mn_1.5O₄ cathode materials with different lithium excess amount (0, 2%, 6%, 10%) were synthesized by a facile solid-state method. The effect of lithium excess amount on the microstructure, morphology, and electrochemical properties of LiNi_0.5Mn_1.5O₄ materials was systematically investigated. The results show that the lithium excess amount does not change the particle morphology and size obviously; thus, the electrochemical properties of LiNi_0.5Mn_1.5O₄ are mainly determined by structural characteristics. With the increase of lithium excess amount, the cation disordering degree (Mn³⁺ content) and phase purity first increase and then decrease, while the cation mixing extent has the opposite trend. Among them, the LiNi_0.5Mn_1.5O₄ material with 6% lithium excess amount exhibits higher disordering degree and lower impurity content and cation mixing extent, thus leading to the optimum electrochemical properties, with discharge capacities of 125.0, 126.1, 124.2, and 118.9 mAh/g at 0.2-, 1-, 5-, and 10-C rates and capacity retention rate of 96.49% after 100 cycles at 1-C rate.     

Recent progress in the electrolytes for improving the cycling stability of LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> high-voltage cathode

High-voltage spinel LiNi_0.5Mn_1.5O₄ has been considered one of the most promising cathode materials for lithium-ion power batteries used in electrical vehicles (EVs) or hybrid electrical vehicles (HEVs) because the high voltage plateau at around 4.7 V makes its energy density (658 Wh kg^?1) 30 and 25 % higher than that of conventional pristine spinel LiMn₂O₄ (440 Wh kg^?1) or olivine LiFePO₄ (500 Wh kg^?1) materials, respectively. Unfortunately, LiNi_0.5Mn_1.5O₄-based batteries with LiPF₆-based carbonate electrolytes always suffer from severe capacity deterioration and poor thermostability because of the oxidization of organic carbonate solvents and decomposition of LiPF₆, especially at elevated temperatures and water-containing environment. The major goal of this review is to highlight the recent advancements in the development of advanced electrolytes for improving the cycling stability and rate capacity of LiNi_0.5Mn_1.5O₄-based batteries. Finally, an insight into the future research and further development of advanced electrolytes for LiNi_0.5Mn_1.5O₄-based batteries is discussed.     

Preparation of LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode materials by electrospinning

LiNi_0.5Mn_1.5O₄ cathode material was prepared by electrospinning using lithium hydroxide, manganese acetate, nickel acetate, acetic acid, ethanol, and poly(vinyl pyrrolidone) as raw materials. The effect of calcination temperature on the structure, morphology, and electrochemical properties was investigated. XRD results indicate that the LiNi_0.5Mn_1.5O₄ composite is well crystallized as a spinel structure at calcination temperature of 650 °C for 3 h. SEM results reveal that this composite has a nanofiber shape with average size of about 300–500 nm. Electrochemical performance tests reveal that this composite shows the initial discharge capacity of 127.8 and 105 mAhg^?1 at 0.1 and 3 C rates, respectively, and exhibits good cycling performance.     

AlF<Subscript>3</Subscript> coating of LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> for high-performance Li-ion batteries

AlF₃-coating is attempted to improve the performance of LiNi_0.5Mn_1.5O₄ cathode materials for Li-ion batteries. The prepared powders are characterized by scanning electron microscope, powder X-ray diffraction, charge/discharge, and impedance. The coated LiNi_0.5Mn_1.5O₄ samples show higher discharge capacity, better rate capability, and higher capacity retention than the uncoated samples. Among the coated samples, 1.0 mol% AlF₃-coated sample shows highest capacity after charge–discharged at 30 mA/g for 3 cycles, but 4.0 mol% coated sample exhibits the highest capacity and cycling stability when cycled at high rate of 150 and 300 mA/g. The 40th cycle discharge capacity at 300 mA/g current still remains 114.8 mAh/g for 4.0 mol% AlF₃-coated LiNi_0.5Mn_1.5O₄, while only 84.3 mAh/g for the uncoated sample.     

Understanding the thermal stability and bonding characteristic of Li<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Ni<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> as cathode materials for lithium-ion battery from first principles

The thermodynamic stability is a very important quantity for the electrode materials, because it is not only related to the electrochemical performances of the materials but also the safety issue of the cells. To evaluate the thermodynamic stability of Li _x Ni_0.5Mn_1.5O₄ (x = 0, 1), the formation enthalpies from elemental phases and oxides were obtained. The values for LiNi_0.5Mn_1.5O₄ were calculated to be ?1341.10 and ?141.84 kJ mol^?1, while those for Ni_0.5Mn_1.5O₄ were ?949.11 and ?49.21 kJ mol^?1. These values are much more negative than those of LiCoO₂ and LiNiO₂ compounds, indicating that the thermodynamic stability of Li _x Ni_0.5Mn_1.5O₄ is better than the two classic compounds. To clarify the microscopic origin, the density of states, magnetic moments, and bond orders were systematically investigated. The results showed that the excellent thermodynamic stability of LiNi_0.5Mn_1.5O₄ is attributed to the absence of Jahn-Teller distortions, strong electrostatic interactions of Li–O ionic bond, and strong Ni–O/Mn–O ionic-covalent mixing bonds. After lithium extraction, the disappearance of the pure Li–O bonds leads to an increase of formation enthalpy, indicating a decreasing thermodynamic stability for Ni_0.5Mn_1.5O₄ with respect to LiNi_0.5Mn_1.5O₄.     

Effect of carbon coating process on the structure and electrochemical performance of LiNi<Subscript>0.5</Subscript>Mn<Subscript>0.5</Subscript>O<Subscript>2</Subscript> used as cathode in Li-ion batteries

LiNi_0.5Mn_0.5O₂ powder was synthesized by a coprecipitation method. LiOH.H₂O and coprecipitated [(Ni_0.5Mn_0.5)C₂O₄] precursors were mixed carefully together and then calcined at 900°C. Surface modified cathode materials were obtained by coating LiNi_0.5Mn_0.5O₂ with a thin layer of amorphous carbon using table sugar and starch as carbon source. Both parent and carbon-coated samples have the characteristic layered structure of LiNi_0.5Mn_0.5O₂ as estimated from X-ray diffractometry measurements. Transmission electron microscope showed the presence of C layer around the prepared particles. TGA analysis emphasized and confirmed the presence of C coating around LiNi_0.5Mn_0.5O₂. It is obvious that the carbon coating appears to be beneficial for the electrochemical performance of the LiNi_0.5Mn_0.5O₂. A capacity of about 150 mAh/g is delivered in the voltage range 2.5–4.5 V at current density C/15 for carbon coated LiNi_0.5Mn_0.5O₂ in comparison with about 165 mAh/g obtained for carbon free LiNi_0.5Mn_0.5O₂ at the same current density and voltage window. About 92% and 82% capacity retention was obtained at 50th cycle for coated LiNi_0.5Mn_0.5O₂ using sucrose and starch, respectively; whereas, 75% was retained after only 30th cycle for carbon free LiNi_0.5Mn_0.5O₂. This improvement is mainly attributed to the presence of thin layer of carbon layer that encapsulate the nanoparticles and improve the conductivity and the electrochemical performance of LiNi_0.5Mn_0.5O₂.     

LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> hollow nano-micro hierarchical microspheres as advanced cathode for lithium ion batteries

The high-voltage spinel-type LiNi_0.5Mn_1.5O₄ (LNMO) is a promising cathode material for next-generation lithium ion batteries. In this study, hollow LNMO microspheres have been synthesized via co-precipitation method accompanied with high-temperature calcinations. The physical and electrochemical properties of the materials are characterized by x-ray diffraction (XRD), TGA, RAMAN, CV, scanning electron microscope (SEM), transmission electon microscopy (TEM), electrochemical impendence spectroscopy (EIS), and charge-discharge tests. The results prove that the microspheres combine hollow structures inward and own a cubic spinel structure with space group of Fd-3m, high crystallinity, and excellent electrochemical performances. With the short Li⁺ diffusion length and hollow structure, the hierarchical LNMO microspheres exhibit 138.2 and 108.5 mAh g^?1 at 0.5 and 10 C, respectively. Excellent cycle stability is also demonstrated with more than 98.8 and 88.2 % capacity retention after 100 cycles at 1 and 10 C, respectively.     

The multiple effects of Al-doping on the structure and electrochemical performance of LiNi<Subscript>0.5</Subscript>Mn<Subscript>0.5</Subscript>O<Subscript>2</Subscript> as cathode material at high voltage

The application of LiNi_0.5Mn_0.5O₂ as a high-voltage cathode material for lithium-ion batteries is limited by its poor cycle performance. Therefore, we attempt to improve the cyclability of this material at high voltage by using a doping method and propose a detailed mechanism for the effect of the doping amount on the structure and electrochemical performance. In this work, LiNi_0.5-zAl_zMn_0.5O₂ (z?=?0.00, 0.03, 0.05, 0.08) electrodes were prepared via a simple co-precipitation followed by a solid-state method. X-ray diffraction and Rietveld refinement revealed that a suitable amount of Al doping into LiNi_0.5Mn_0.5O₂ can stabilize the structure and lower the Li/Ni cation mixing, but an excessive doping would lead to Al-ion doping in the lithium layer, which can block lithium diffusion and affect the rate property. Specifically, LiNi_0.47Al_0.03Mn_0.5O₂ shows a much higher capacity retention compared to LiNi_0.5Mn_0.5O₂ both at 25 °C (78.5 vs. 68.8% at 0.2 C) and 60 °C (70.8 vs. 69.0% at 0.2 C). Moreover, Al-doping can retard the voltage drop during the discharge-charge state, with the discharge voltage for LiNi_0.5-zAl_zMn_0.5O₂ (z?=?0.00, 0.03, 0.05, 0.08) decreasing slowly with increasing Al content.     

A high-voltage lithium-ion battery prepared using a Sn-decorated reduced graphene oxide anode and a LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode

This paper describes the preparation and characterization of a high-voltage lithium-ion battery based on Sn-decorated reduced graphene oxide and LiNi_0.5Mn_1.5O₄ as the anode and cathode active materials, respectively. The Sn-decorated reduced graphene oxide is prepared using a microwave-assisted hydrothermal synthesis method followed by reduction at high temperature of a mixture of (C₆H₅)₂SnCl₂ and graphene oxide. The so-obtained anode material is characterized by thermogravimetric analysis, X-ray diffraction, scanning electron microscopy, and electron diffraction spectroscopy. The LiNi_0.5Mn_1.5O₄ is a commercially available product. The two materials are used to prepare composite electrodes, and their electrochemical properties are investigated by galvanostatic charge/discharge cycles at various current densities in lithium cells. The electrodes are then used to assemble a high-voltage lithium-ion cell, and the cell is tested to evaluate its performance as a function of discharge rate and cycle number.     

Investigation on LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode material based on the precursor of nickel-manganese compound for lithium-ion battery

The high-voltage spinel LiNi_0.5Mn_1.5O₄ (LNMO) with submicron particle size (LNMO-850₅P700₁₀) has been synthesized based on nickel-manganese compound, which is obtained from pre-sintering the nickel-manganese hydroxide precipitation at 850 °C. The LNMO materials based on nickel-manganese hydroxide (LNMO-700₁₀, LNMO-850₅700₁₀, and LNMO-850₁₀700₁₀) have also been synthesized for comparison to study the pre-sintering impact on the properties of LiNi_0.5Mn_1.5O₄ material. The morphologies and structures of the obtained samples have been analyzed by X-ray powder diffraction and scanning electron microscopy. The nickel-manganese compound has a spinel structure with high crystallinity, making it a good precursor to form high-performance LNMO with lower content of Mn³⁺ and impurity. The obtained LNMO-850₅P700₁₀ delivers discharge capacities of 125.4 mA h g^?1 at 0.2 C, and the capacity retention of 15 C reaches 73.8 % of the capacity retention of 0.2? C. Furthermore, it shows a superior cyclability with the capacity retention of 96.4 % after 150 cycles at 5 ?C. Compared with the synthesis method without pre-sintering, the synthesis method with pre-sintering can save energy while reaching the same discharge specific capacity.     

A lithium salt additive Li<Subscript>2</Subscript>ZrF<Subscript>6</Subscript> for enhancing the electrochemical performance of high-voltage LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode

In this work, Li₂ZrF₆, a lithium salt additive, is reported to improve the interface stability of LiNi_0.5Mn_1.5O₄ (LNMO)/electrolyte interface under high voltage (4.9 V vs Li/Li⁺). Li₂ZrF₆ is an effective additive to serve as an in situ surface coating material for high-voltage LNMO half cells. A protective SEI layer is formed on the electrode surface due to the involvement of Li₂ZrF₆ during the formation of SEI layer. Charge/discharge tests show that 0.15 mol L^?1 Li₂ZrF₆ is the optimal concentration for the LiNi_0.5Mn_1.5O₄ electrode and it can improve the cycling performance and rate property of LNMO/Li half cells. The results obtained by electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS) demonstrate that Li₂ZrF₆ can facilitate the formation of a thin, uniform, and stable solid electrolyte interface (SEI) layer. This layer inhibits the oxidation decomposition of the electrolyte and suppresses the dissolution of the cathode materials, resulting in improved electrochemical performances.     

Acacia gum-assisted co-precipitating synthesis of LiNi<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>O<Subscript>2</Subscript> cathode material for lithium ion batteries

LiNi_0.5Co_0.2Mn_0.3O₂ particles of uniform size were prepared through carbonate co-precipitation method with acacia gum. The precursor of carbonate mixture was calcined at 800 °C, and a well-crystallized Ni-rich layered oxide was got. The phase structure and morphology were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The micro-sized particles delivered high initial discharge capacity of 164.3 mA h g^?1 at 0.5 C (1 C?=?200 mA g^?1) between 2.5 and 4.3 V with capacity retention of 87.5 % after 100 cycles. High reversible discharge capacities of 172.4 and 131.4 mA h g^?1 were obtained at current density of 0.1 and 5 C, respectively. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were performed to further study the LiNi_0.5Co_0.2Mn_0.3O₂ particles. Anyway, the excellent electrochemical performances of LiNi_0.5Co_0.2Mn_0.3O₂ sample should be attributed to the use of acacia gum.     

Improving the rate performance and stability of LiNi<Subscript>0.6</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.2</Subscript>O<Subscript>2</Subscript> in high voltage lithium-ion battery by using fluoroethylene carbonate as electrolyte additive

Fluoroethylene carbonate (FEC) is investigated as the electrolyte additive to improve the electrochemical performance of high voltage LiNi_0.6Co_0.2Mn_0.2O₂ cathode material. Compared to LiNi_0.6Co_0.2Mn_0.2O₂/Li cells in blank electrolyte, the capacity retention of the cells with 5 wt% FEC in electrolytes after 80 times charge-discharge cycle between 3.0 and 4.5 V significantly improve from 82.0 to 89.7%. Besides, the capacity of LiNi_0.6Co_0.2Mn_0.2O₂/Li only obtains 12.6 mAh g^?1 at 5 C in base electrolyte, while the 5 wt% FEC in electrolyte can reach a high capacity of 71.3 mAh g^?1 at the same rate. The oxidative stability of the electrolyte with 5 wt% FEC is evaluated by linear sweep voltammetry and potentiostatic data. The LSV results show that the oxidation potential of the electrolytes with FEC is higher than 4.5 V vs. Li/Li⁺, while the oxidation peaks begin to appear near 4.3 V in the electrolyte without FEC. In addition, the effect of FEC on surface of LiNi_0.6Co_0.2Mn_0.2O₂ is elucidated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). The analysis result indicates that FEC facilitates the formation of a more stable surface film on the LiNi_0.6Co_0.2Mn_0.2O₂ cathode. The electrochemical impedance spectroscopy (EIS) result evidences that the stable surface film could improve cathode electrolyte interfacial resistance. These results demonstrate that the FEC can apply as an additive for 4.5 V high voltage electrolyte system in LiNi_0.6Co_0.2Mn_0.2O₂/Li cells.     

Enhanced electrochemical properties and thermal stability of LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> by surface modification with Eu<Subscript>2</Subscript>O<Subscript>3</Subscript>

Layered LiNi_1/3Co_1/3Mn_1/3O₂ cathode material is synthesized via a sol-gel method and subsequently surface-modified with Eu₂O₃ layer by a wet chemical process. The effect of Eu₂O₃ coating on the electrochemical performances and thermal stability of LiNi_1/3Co_1/3Mn_1/3O₂@Eu₂O₃ cells is investigated systematically by the charge/discharge testing, cyclic voltammograms, AC impedance spectroscopy, and DSC measurements, respectively. In comparison, the Eu₂O₃-coated sample demonstrates better electrochemical performances and thermal stability than that of the pristine one. After 100 cycles at 1C, the Eu₂O₃-coated LiNi_1/3Co_1/3Mn_1/3O₂ cathode demonstrates stable cyclability with capacity retention of 92.9 %, which is higher than that (75.5 %) of the pristine one in voltage range 3.0–4.6 V. Analysis from the electrochemical measurements reveals that the remarkably improved performances of the surface-modified composites are mainly ascribed to the presence of Eu₂O₃-coating layer, which could efficiently suppress the undesirable side reaction and increasing impedance, and enhance the structural stability of active material.     

Nanosized LiNi0.5Mn1.5O4 spinels synthesized by a high-oxidation-state manganese sol–gel method

Nanosized LiNi_0.5Mn_1.5O₄ spinels with the uniform average particle size of about 80–100 nm were synthesized by a high-oxidation-state manganese sol–gel method. It indicates that the resulting nanosized LiNi_0.5Mn_1.5O₄ materials not only have a phase-pure cubic spinel structure without any impurity but also have a good dispersion even without any physical treatment. Besides, the cell based upon the resulting nanosized LiNi_0.5Mn_1.5O₄ materials shows good cycle stability and ratio performance. It suggests that the novel method would be helpful for the synthesis and application of LiNi_0.5Mn_1.5O₄ cathode.     

Synthesis of spinel LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> as advanced cathode via a modified oxalate co-precipitation method

Spinel-type LiNi_0.5Mn_1.5O₄ (LNMO) cathode materials for lithium ion batteries have been synthesized via a modified oxalate co-precipitation method. By virtue of the co-precipitation of Li⁺ with transition metal ions, the target materials can be obtained through one-pot reaction without subsequent mixing with lithium salts. What’s more, a uniform distribution between the lithium and transition metal ions at molecular level could be realized, which is beneficial for final electrochemical performances. The physical and electrochemical properties of the material are characterized by XRD, TGA, EDS, FT-IR, SEM, CV, EIS, and charge/discharge tests. The results prove that the as-prepared material owns a cubic spinel structure with a space group of Fd-3m, high crystallinity, uniform particle size, and excellent electrochemical performances. A higher initial capacity and superior rate performance are delivered compared with that of material by conventional co-precipitation method. High capacities of 131.7 and 104.0 mAh g^?1 could be displayed at 0.5 and 10 C, respectively. Excellent cycle stability is also demonstrated with more than 98.5 % capacity retention after 100 cycles at 1 C.     

Effects of different precipitants on LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> for lithium ion batteries prepared by modified co-precipitation method

Effects of two different precipitants of Na₂CO₃ and Na₂C₂O₄ on LiNi_0.5Mn_1.5O₄ (LNMO) cathode materials, which are prepared by a modified co-precipitation method, have been investigated. Various measurements have been applied to characterize the physical and electrochemical performances of LNMO. Compared with the LNMO prepared by the oxalate co-precipitation (LNMO2), the material synthesized by the carbonate co-precipitation (LNMO1) not only shows more uniform porosity and smaller particles but also has a better rate capability and cycling performance. In addition, the sample prepared by carbonate has a stable spherical structure, due to the fact that carbonate co-precipitation with less gas release during calcination can prevent the destruction of the as-prepared LNMO material structure and promote the formation of regular particle and aperture. Based on the electrochemical test results, LNMO1 shows greatly enhanced electrochemical performance of a high initial discharge capacity of 125.6 mAh g^?1 at 0.25 °C, as well as a preferably capacity retention of 96.5% after 100 cycles at 0.5 °C. And even at a high rate of 10 °C, the discharge capacity of LNMO1-based cell still approaches 83.1 mAh g^?1.     

Magnetic properties of LiNi<Subscript>0.5</Subscript>Mn<Subscript>0.47</Subscript>Al<Subscript>0.03</Subscript>O<Subscript>2</Subscript> as positive electrode for Li-ion batteries

The layered LiNi_0.5Mn_0.47Al_0.03O₂ was synthesized by wet chemical method and characterized by X-ray diffraction and analysis of magnetic measurements. The powders adopted the α-NaFeO₂ structure. This substitution of Al for Mn promotes the formation of Li(Ni_0.47²⁺Ni_0.03³⁺Mn_0.47⁴⁺Al_0.03³⁺)O₂ structures and induces an increase in the average oxidation state of Ni, thereby leading to the shrinkage of the lattice unit cell. The concentration of antisite defects in which Ni²⁺ occupies the (3a) Li lattice sites in the Wyckoff notation has been estimated from the ferromagnetic Ni²⁺(3a)–Mn⁴⁺(3b) pairing observed below 140 K. The substitution of 3% Al for Mn reduces the amount of antisite defects from 7% to 6.4–6.5%. The analysis of the magnetic properties in the paramagnetic phase in the framework of the Curie–Weiss law agrees well with the combination of Ni²⁺ (S = 1), Ni³⁺ (S = 1/2) and Mn⁴⁺ (S = 3/2) spin-only values. Delithiation has been made by the use of K₂S₂O₈. According to this process, known to be softer than the electrochemical one, the nickel ions in the (3b) sites are converted into Ni⁴⁺ in the high spin configuration, while Ni²⁺(3a)–Mn⁴⁺(3b) ferromagnetic pairs remain, as the Li⁺(3b) ions linked to the Ni²⁺(3a) ions in the antisite defects are not removed. The results show that the antisite defect is surrounded by Mn⁴⁺ ions, implying the nonuniform distribution of the cations in agreement with previous NMR and neutron experiments.     

Structural and magnetic properties of LiNi0.5Mn1.5O4 and LiNi0.5Mn1.5O4-δ spinels： A first-principles study

<正>Structural and magnetic properties of LiNi_0.5Mn_1.5O₄ and LiNi_0.5Mn_1.5O_4-δ are investigated using densityfunctional theory calculations.Results indicate that nonstoichiometric LiNi_0.5Mn_1.5O_4-δ and stoichiometric LiNi_0.5Mn_1.5O₄ exhibit two different structures,i.e.,the face-centred cubic（Fd-3m） and primitive,or simple,cubic （P4₃32） space groups,respectively.It is found that the magnetic ground state of LiNi_0.5Mn_1.5O₄（P4₃32 and Fd-3m） is a ferrimagnetic state in which the Ni and Mn sublattices are ferromagnetically ordered along the[110]direction whereas they are antiferromagnetic with respect to each other.We demonstrate that it is the presence of an O-vacancy in LiNi_0.5Mn_1.5O_4-δ with the Fd-3m space group that results in its superior electronic conductivity compared with LiNi_0.5Mn_1.5O₄ with the P4₃32 space group.     

Improvement of electrochemical performance for AlF<Subscript>3</Subscript>-coated Li<Subscript>1.3</Subscript>Mn<Subscript>4/6</Subscript>Ni<Subscript>1/6</Subscript>Co<Subscript>1/6</Subscript>O<Subscript>2.40</Subscript> cathode materials for Li-ion batteries

Li-rich layered-layered-Spinel structure spherical Li_1.3Mn_4/6Ni_1/6Co_1/6O_2.40 particles was successfully prepared and coated with a uniform layer by a two-step co-precipitation method and evaluated in lithium cells. The structures and electrochemical properties of pristine Li_1.3Mn_4/6Ni_1/6Co_1/6O_2.40 and AlF₃-coated Li_1.3Mn_4/6Ni_1/6Co_1/6O_2.40 were characterized. When the coating amount was 2 wt%, the cathode showed the best cycling performance and rate capability compared to others. The AlF₃-coated Li_1.3Mn_4/6Ni_1/6Co_1/6O_2.40 Li-ion cell cathode had a capacity retention of 90.07 % after 50 cycles at 0.5 C over 2.0–4.8 V, while the pristine Li_1.3Mn_4/6Ni_1/6Co_1/6O_2.40 exhibited capacity retention of only 80.73 %. Moreover, the rate capability and cyclic performance also improved. Electrochemical impedance spectroscopy testing revealed that the improved electrochemical performance might attribute to the AlF₃ coating layer which can suppress the increase of impedance during the charging and discharging process by preventing direct contact between the highly delithiated active material and electrolyte.