Fabrication of urchin-like NiCo<Subscript>2</Subscript>O<Subscript>4</Subscript> microspheres assembled by using SDS as soft template for anode materials of Lithium-ion batteries

In this paper, the urchin-like NiCo₂O₄ microspheres assembled by using sodium dodecyl sulfate (SDS) as soft template are successfully fabricated by a facile procedure including microemulsion-solvothermal reaction and subsequent calcination at 400 °C for 4 h. The structure and morphology of synthesized NiCo₂O₄ particles are investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM). It has been clearly revealed that the prepared three-dimensional urchin-like NiCo₂O₄ microspheres are constituted by one-dimension nanowires. As it is applied to anode for lithium-ion batteries (LIBs), the initial coulombic efficiency is up to 75.7%, and the specific reversible capacity retains up to 1034.2 mAh/g even after 40 cycles at a current density of 100 mA/g. Furthermore, as the current density gradually increases to 800 mA/g, it still delivers the reversible capacity of 895.4 mAh/g. The high reversible specific capacity, perfect cyclability, and rate performance are attributed to the unique urchin-like NiCo₂O₄ microspheres, which can alleviate the volume expansion and shorten the diffusion path of ions and electrons during lithiation/delithiation process. The self-standing urchin-like NiCo₂O₄ microspheres may be a very promising candidate in place of the commercial graphite-based anode materials for high-performance LIBs.     

Spray pyrolysis-deposited TiO<Subscript>2</Subscript> thin films as high-performance lithium ion battery anodes

Focusing on additive-free electrodes, thin films are of typical interest as electrodes for lithium ion battery application. Herein, we report the fabrication of TiO₂ thin films by spray pyrolysis deposition technique. X-ray diffraction and transmission electron microscopic analysis confirms the formation of anatase TiO₂. Electrochemical evaluation of these sub-micron TiO₂ thin films exhibits high-rate performance and long cycling stability. At 1C rate (1C?=?335 mA/g), the electrode delivered discharge capacity of 247 mAh/g allowing about 0.74 lithium into the structure. The electrodes also delivered specific capacities of 122 and 72 mAh/g at 10 and 30C rates, respectively. Without conductive additives, this excellent performance can be attributed to the nanosize effect of TiO₂ particles combined with the uniform porous architecture of the electrode. Upon cycling at high rates (10 and 30C), the electrode exhibited excellent cycling stability and retention, specifically only <?0.6% capacity loss per cycle over 2500 cycles.     

AlF<Subscript>3</Subscript> coating of LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> for high-performance Li-ion batteries

AlF₃-coating is attempted to improve the performance of LiNi_0.5Mn_1.5O₄ cathode materials for Li-ion batteries. The prepared powders are characterized by scanning electron microscope, powder X-ray diffraction, charge/discharge, and impedance. The coated LiNi_0.5Mn_1.5O₄ samples show higher discharge capacity, better rate capability, and higher capacity retention than the uncoated samples. Among the coated samples, 1.0 mol% AlF₃-coated sample shows highest capacity after charge–discharged at 30 mA/g for 3 cycles, but 4.0 mol% coated sample exhibits the highest capacity and cycling stability when cycled at high rate of 150 and 300 mA/g. The 40th cycle discharge capacity at 300 mA/g current still remains 114.8 mAh/g for 4.0 mol% AlF₃-coated LiNi_0.5Mn_1.5O₄, while only 84.3 mAh/g for the uncoated sample.     

Synthesis,characterization, and cell performance of Li<Subscript>0.5</Subscript>FeV<Subscript>1.5</Subscript>O<Subscript>4</Subscript>

A Li_0.5FeV_1.5O₄ sample was synthesized using sol-gel route. The X-ray diffraction study indicates formation of spinel phase (with Fd3m space group) for this sample. LiO₄, LiO₆, and V-O bonds were identified from the Raman spectrum, while LiO₄ and Fe-O bonds were identified from the FTIR spectrum of this sample phase. The FESEM study indicates formation of inhomogeneous grains. The surface area of 74.39 m²/g was estimated from the Brunauer-Emmett-Teller (BET) surface area analysis technique. The cyclic voltammetry study of Li_0.5FeV_1.5O₄ indicates an anodic peak at 2.1 V while a cathodic peak at 1.98 V. The charge-discharge study exhibits two voltage plateaus respectively at 2.1 and at 4 V. Stable electrochemical capacity of 40 mAh/g for Li_0.5FeV_1.5O₄ was found for 30 cycles. The electrochemical impedance spectroscopy study indicates smaller bulk resistance and higher ionic diffusion, i.e., less Warburg impedance for this phase. An energy density of 89 Wh/kg, a power density of 33 W/kg, and a 90% Coulombic efficiency was achieved with relatively good cyclic stability from Li_0.5FeV_1.5O₄.     

Influence of co-precipitation temperature on microstructure and electrochemical properties of Li[Li<Subscript>0.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>]O<Subscript>2</Subscript> cathode materials for lithium ion batteries

The layered Li-rich Mn-based cathode materials Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ were prepared by using co-precipitation technique at different temperatures, and their crystal microstructure and particle morphology were observed and analyzed by XRD and SEM. The electrochemical properties of these samples were investigated by using charge-discharge tests, electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV), respectively. The results indicated that all samples are of high purity. When the precursors were co-precipitated at 50 °C, their cathode materials have the most uniform and full particles and exhibit the highest initial discharge capacity (289.4 mAh/g at 0.1C), the best cycle stability (capacity retention rate of 91.2 % after 100 cycles at 0.5C), and the best rate performance. The EIS results show that the lower charge transfer resistance of 50 °C sample is responsible for its superior discharge capacity and rate performance.     

Low-temperature synthesis of Cu-doped Li<Subscript>1.2</Subscript>V<Subscript>3</Subscript>O<Subscript>8</Subscript> as cathode for reversible lithium storage

Li_{1 .2}V₃O₈ and Cu-doped Li_1.2V₃O₈ were prepared at a temperature as low as 300 °C by a sol-gel method. The structure, morphology, and electrochemical performance of the as-prepared samples were characterized by means of X-ray diffraction, scanning electron microscopy, electrochemical impedance spectroscopy, and the galvanostatic discharge–charge techniques. It is found that the Cu-doped Li_1.2V₃O₈ sample exhibits less capacity loss during repeated cycling than the undoped one. The Cu-doped Li_1.2V₃O₈ sample demonstrates the first discharge capacity of 275.9 mAh/g in the range of 3.8–1.7 V at a current rate of 30 mA/g and remains at a stable discharge capacity of 264 mAh/g within 30 cycles. Furthermore, the possible role that copper plays in enhancing the cycleability of Li_1.2V₃O₈ has also been elucidated.     

Synthesis of Li(Ni<Subscript>0.6</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.2</Subscript>)O<Subscript>2</Subscript> with sodium DL-lactate as an eco-friendly chelating agent and its electrochemical performances for lithium-ion batteries

(Ni_0.6Co_0.2Mn_0.2)(OH)₂ precursor has been successfully prepared using hydroxide co-precipitation method. The thermodynamic model of hydroxide co-precipitation with sodium DL-lactate as an eco-friendly chelating agent is proposed. The microstructures of (Ni_0.6Co_0.2Mn_0.2)(OH)₂ precursors and Li(Ni_0.6Co_0.2Mn_0.2)O₂ cathode materials are investigated using X-ray diffractometer and scanning electronic microscopy, while the electrochemical performances of Li(Ni_0.6Co_0.2Mn_0.2)O₂ cathode materials are measured using a charge–discharge test. The influences of pH value on the structure and morphological and electrochemical performances of Li(Ni_0.6Co_0.2Mn_0.2)O₂ cathode materials have been discussed in detail. The results show that the sample at pH?=?11.5 exhibits the best lamellar structure and lowest cation mixing, while the sample at pH?=?11.0 delivers the most uniform and full particles and possesses the highest initial charge–discharge performance of 183.4 mAh/g and the best coulombic efficiency of 77.9% at the voltage range of 3.0–4.3 V. Even after 100 cycles, its discharge capacity still remains 165.2 mAh/g with the best retention rate of 90.1%. Furthermore, the sample at pH?=?11.0 delivers the highest discharge capacity at each current density. Even if discharged at 5C (1000 mA/g), the capacity of 115.6 mAh/g has been achieved. The sample at pH?=?11.0 exhibits the highest Li-ion diffusion coefficients (2.072?×?10^?12 cm²/s).     

Synthesis of hierarchical nanospheres Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/graphene composite and its application in lithium-ion battery as a high-performance anode material

A hierarchically nanospherical α-Fe₂O₃/graphene composite with a homogeneous mono-pore size of 4 nm has been prepared using a hydrothermal method. The composite showed an extremely high rate performance and good cycling stability when applied as an anode material for lithium-ion batteries owing to its unique three dimensional architecture. A specific capacity of 110 mAh/g was obtained at an extremely high current rate of 40 A/g and recover to 830 mAh/g at 0.5 A/g after 60 cycles. After 250 cycles at 2 A/g, the composite electrode exhibited a capacity of 630 mAh/g with a columbic efficiency of 99.5 %.     

Enhanced electrochemical performance of Cu<Subscript>2</Subscript>O-modified Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode material for lithium-ion batteries

Li₄Ti₅O₁₂/Cu₂O composite was prepared by ball milling Li₄Ti₅O₁₂ and Cu₂O with further heat treatment. The structure and electrochemical performance of the composite were investigated via X-ray diffraction, scanning electron microscopy, energy-dispersive spectroscopy, cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge–discharge tests. Li₄Ti₅O₁₂/Cu₂O composite exhibited much better rate capability and capacity performance than pristine Li₄Ti₅O₁₂. The discharge capacity of the composite at 2 C rate reached up to 122.4 mAh g^?1 after 300 cycles with capacity retention of 91.3 %, which was significantly higher than that of the pristine Li₄Ti₅O₁₂ (89.6 mAh g^?1). The improvement can be ascribed to the Cu₂O modification. In addition, Cu₂O modification plays an important role in reducing the total resistance of the cell, which has been demonstrated by the electrochemical impedance spectroscopy analysis.     

Improved electrochemical performance of Li<Subscript>1.2</Subscript>Ni<Subscript>0.2</Subscript>Mn<Subscript>0.6</Subscript>O<Subscript>2</Subscript> cathode material with fast ionic conductor Li<Subscript>3</Subscript>VO<Subscript>4</Subscript> coating

Layered lithium-enriched nickel manganese oxides Li_1.2Ni_0.2Mn_0.6O₂ have been synthesized and coated by fast ionic conductor Li₃VO₄ with varying amounts (1, 3, and 5 wt%) in this paper. The effect of Li₃VO₄ on the physical and electrochemical properties of Li_1.2Ni_0.2Mn_0.6O₂ has been discussed through the characterizations of X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscope (TEM), discharge, cyclic performance, rate capability, and electrochemical impedance spectroscopy (EIS). The discharge capacity and coulomb efficiency of Li_1.2Ni_0.2Mn_0.6O₂ in the first cycle have been improved after Li₃VO₄ coating. And, the 3 wt% Li₃VO₄-coated Li_1.2Ni_0.2Mn_0.6O₂ shows the best discharge capacity (246.8 mAh g^?1), capacity retention (97.3 % for 50 cycles), and rate capability (90.4 mAh g^?1 at 10 C). Electrochemical impedance spectroscopy (EIS) results show that the R _ct of Li_1.2Ni_0.2Mn_0.6O₂ electrode decreases after Li₃VO₄ coating, which is due to high lithium ion diffusion coefficient of Li₃VO₄, is responsible for superior rate capability.     

Carbon@SnS<Subscript>2</Subscript> core-shell microspheres for lithium-ion battery anode materials

A novel unique C@SnS₂ core-shell structure composites consisting of well-dispersity carbon microspheres and ultrathin tin disulfide nanosheets were successfully synthesized for the first time through a simple solvothermal method. The thin SnS₂ nanosheets grew onto the carbon microspheres surfaces perpendicularly and formed the close-knit porous structure. When it was used as anode materials for lithium-ion batteries, the hybrid C@SnS₂ core-shell structure composites showed a remarkable electrochemical property than pure SnS₂ nanosheets. Typically, the hybrid composites with SnS₂ nanosheet shells and carbon microsphere’s core exhibited an excellent initial discharge capacity of 1611.6 mAh/g. Moreover, the hybrid composites exhibited capacities of 474.8–691.6 mAh/g at 100 mA/g over 50 battery cycles, while the pure SnS₂ could deliver capacities of 243–517.6 mAh/g in the tests. The results indicated that the improvement of lithium storage performance of the core-shell structure C@SnS₂ anode materials in terms of rate capability and cycling reversibility owing to the introduction of the smooth carbon microspheres and special designing of core-shell structure.     

Influence of cooling mode on the electrochemical properties of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode materials for lithium-ion batteries

Li₄Ti₅O₁₂ (LTO) was synthesized with two different cooling methods by solid-state method, namely fast cooling and air cooling. The samples were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), galvanostatic charge–discharge test, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS), respectively. XRD revealed that the basic LTO structure was not changed. FESEM images showed that fast cooling effectively reduced the particle sizes and the agglomeration of particles. Galvanostatic charge–discharge test showed that the air cooling sample exhibited a mediocre performance, having an initial discharge capacity of 136.3mAh?·?g^?1 at 0.5 C; however, the fast cooling sample demonstrated noticeable improvement in both of its discharge capacity and rate capability, with a high initial capacity value of 142.7 mAh?·?g^?1 at 0.5 C. CV measurements also revealed that fast cooling enhanced the reversibility of the LTO. EIS confirmed that fast cooling resulted in lower electrochemical polarization and a higher lithium-ion diffusion coefficient. Therefore, fast cooling have a great impact on discharge capacity, rate capability, and cycling performance of LTO anode materials for lithium-ion batteries.     

Preparation and electrochemical properties of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>/Ti<Subscript>4</Subscript>O<Subscript>7</Subscript> composite for lithium-ion batteries

In order to improve the rate capability of Li₄Ti₅O₁₂, Ti₄O₇ powder was successfully fabricated by improved hydrogen reduction method, then a dual-phase composite Li₄Ti₅O₁₂/Ti₄O₇ has been synthesized as anode material for lithium-ion batteries. It is found that the Li₄Ti₅O₁₂/Ti₄O₇ composite shows higher reversible capacity and better rate capability compared to Li₄Ti₅O₁₂. According to the charge-discharge tests, the Li₄Ti₅O₁₂/Ti₄O₇ composite exhibits excellent rate capability of 172.3 mAh g^?1 at 0.2 C, which is close to the theoretical value of the spinel Li₄Ti₅O₁₂. More impressively, the reversible capacity of Li₄Ti₅O₁₂/Ti₄O₇ composite is 103.1 mAh g^?1 at the current density of 20 C after 100th cycles, and it maintains 84.8% of the initial discharge capacity, whereas that of the bare spinel Li₄Ti₅O₁₂ is only 22.3 mAh g^?1 with a capacity retention of 31.1%. The results indicate that Li₄Ti₅O₁₂/Ti₄O₇ composite could be a promising anode material with relative high capacity and good rate capability for lithium-ion batteries.     

Hexagonal-like NiCo<Subscript>2</Subscript>O<Subscript>4</Subscript> nanostructure based high-performance supercapacitor electrodes

A novel approach of double hydroxide-mediated synthesis of nickel cobaltite (NiCo₂O₄) electro-active material by the hydrothermal method is reported. The obtained NiCo₂O₄ electro-active material displays the spinel cubic phase and hexagonal-like morphology. Thermogravimetry analysis confirms the thermal stability of the electrode material. The functional groups and phase formation of NiCo₂O₄ have been confirmed by FT-IR and Raman spectral analysis. The modified NiCo₂O₄ electrode exhibits the highest specific capacitance of 767.5 F g^?1 at a current density of 0.5 A g^?1 in 3 M KOH electrolyte and excellent cyclic stability (94 % capacitance retention after 1000 cycles at a high current density of 5 A g^?1). The excellent electrochemical performance of the electrode is attributed to the hexagonal-like morphology, which contributes to the rich surface electro-active sites and easy transport pathway for the ions during the electrochemical reaction. The attractive Faradic behavior of NiCo₂O₄ electrode has been ascribed to the redox contribution of Ni²⁺/Ni³⁺ and Co²⁺/Co³⁺ metal species in the alkaline medium. The symmetrical two-electrode cell has been fabricated using the NiCo₂O₄ electro-active material with excellent electrochemical properties for supercapacitor applications.     

Improvement of electrochemical performance for AlF<Subscript>3</Subscript>-coated Li<Subscript>1.3</Subscript>Mn<Subscript>4/6</Subscript>Ni<Subscript>1/6</Subscript>Co<Subscript>1/6</Subscript>O<Subscript>2.40</Subscript> cathode materials for Li-ion batteries

Li-rich layered-layered-Spinel structure spherical Li_1.3Mn_4/6Ni_1/6Co_1/6O_2.40 particles was successfully prepared and coated with a uniform layer by a two-step co-precipitation method and evaluated in lithium cells. The structures and electrochemical properties of pristine Li_1.3Mn_4/6Ni_1/6Co_1/6O_2.40 and AlF₃-coated Li_1.3Mn_4/6Ni_1/6Co_1/6O_2.40 were characterized. When the coating amount was 2 wt%, the cathode showed the best cycling performance and rate capability compared to others. The AlF₃-coated Li_1.3Mn_4/6Ni_1/6Co_1/6O_2.40 Li-ion cell cathode had a capacity retention of 90.07 % after 50 cycles at 0.5 C over 2.0–4.8 V, while the pristine Li_1.3Mn_4/6Ni_1/6Co_1/6O_2.40 exhibited capacity retention of only 80.73 %. Moreover, the rate capability and cyclic performance also improved. Electrochemical impedance spectroscopy testing revealed that the improved electrochemical performance might attribute to the AlF₃ coating layer which can suppress the increase of impedance during the charging and discharging process by preventing direct contact between the highly delithiated active material and electrolyte.     

Investigation on the electrochemical performances of Li<Subscript>4</Subscript>Mn<Subscript>5</Subscript>O<Subscript>12</Subscript> for battery applications

In this study, well-crystallized Li₄Mn₅O₁₂ powder was synthesized by a self-propagating combustion method using citric acid as a reducing agent. Various conditions were studied in order to find the optimal conditions for the synthesis of pure Li₄Mn₅O₁₂. The precursor obtained was then annealed at different temperatures for 24 h in a furnace. X-ray diffraction results showed that Li₄Mn₅O₁₂ crystallite is stable at relatively low temperature of 400 °C but decompose to spinel LiMn₂O₄ and monoclinic Li₂MnO₃ at temperatures higher than 500 °C. The prepared samples were also characterized by FESEM and charge-discharge tests. The result showed that the specific capacity of 70.7 mAh/g was obtained within potential range of 4.2 to 2.5 V at constant current of 1.0 mA. The electrochemical performances of Li₄Mn₅O₁₂ material was further discussed in this paper.     

NiCo<Subscript>2</Subscript>O<Subscript>4</Subscript> polyhedra with controllable particle size as high-performance anode for lithium-ion battery

Different particle sizes of dodecahedron precursors are synthesized by controlling the polarity of the solution. Through the results of scanning electron microscope (SEM) images, it can be found that different particle sizes of precursors present obvious edge angles and their morphology can be well retained after annealing. X-ray diffraction (XRD) measurements suggest that the annealed polyhedral products are pure single-phase NiCo₂O₄. When tested as lithium-ion battery anode, 0.5 μm NiCo₂O₄ polyhedra exhibits a specific capacity of 1050 mAh g^?1 at 0.1 C at the 60th cycle, which was higher than theoretical capacity of single metal oxide (NiO 718 mAh g^?1 and Co₃O₄ 890 mAh g^?1). It also exhibits the highest rate capability with an average discharge capacity of 890, 700, 490, 330, and 300 mAh g^?1 at 0.5, 2, 4, 8, and 10 C, respectively. Those advantages are attributed to that small-sized particle with great surface areas decrease the actual current density at the surface and inner of the prepared electrode.     

Acacia gum-assisted co-precipitating synthesis of LiNi<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>O<Subscript>2</Subscript> cathode material for lithium ion batteries

LiNi_0.5Co_0.2Mn_0.3O₂ particles of uniform size were prepared through carbonate co-precipitation method with acacia gum. The precursor of carbonate mixture was calcined at 800 °C, and a well-crystallized Ni-rich layered oxide was got. The phase structure and morphology were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The micro-sized particles delivered high initial discharge capacity of 164.3 mA h g^?1 at 0.5 C (1 C?=?200 mA g^?1) between 2.5 and 4.3 V with capacity retention of 87.5 % after 100 cycles. High reversible discharge capacities of 172.4 and 131.4 mA h g^?1 were obtained at current density of 0.1 and 5 C, respectively. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were performed to further study the LiNi_0.5Co_0.2Mn_0.3O₂ particles. Anyway, the excellent electrochemical performances of LiNi_0.5Co_0.2Mn_0.3O₂ sample should be attributed to the use of acacia gum.     

Roles of Al-doped ZnO (AZO) modification layer on improving electrochemical performance of LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> thin film cathode

Al-doped ZnO (AZO) was sputtered on the surface of LiNi_1/3Co_1/3Mn_1/3O₂ (NCM) thin film electrode via radio frequency magnetron sputtering, which was demonstrated to be a useful approach to enhance electrochemical performance of thin film electrode. The structure and morphology of the prepared electrodes were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive spectrometer, and transmission electron microscopy techniques. The results clearly demonstrated that NCM thin film showed a strong (104) preferred orientation and AZO was uniformly covered on the surface of NCM electrode. After 200 cycles at 50 μA μm^?1 cm^?2, the NCM/AZO-60s electrode delivered highest discharge capacity (78.1 μAh μm^?1 cm^?2) compared with that of the NCM/AZO-120s electrode (62.4 μAh μm^?1 cm^?2) and the bare NCM electrode (22.3 μAh μm^?1 cm^?2). In addition, the rate capability of the NCM/AZO-60s electrode was superior to the NCM/AZO-120s and bare NCM electrodes. The improved electrochemical performance can be ascribed to the appropriate thickness of the AZO coating layer, which not only acted as HF scavenger to keep a stable electrode/electrolyte interface but also reduced the charge transfer resistance during cycling.     

ZnO-coated LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cathode material for lithium-ion batteries synthesized by a combustion method

ZnO-coated LiMn₂O₄ cathode materials were prepared by a combustion method using glucose as fuel. The phase structures, size of particles, morphology, and electrochemical performance of pristine and ZnO-coated LiMn₂O₄ powders are studied in detail by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), galvanostatic charge-discharge test, and X-ray photoelectron spectroscopy (XPS). XRD patterns indicated that surface-modified ZnO have no obvious effect on the bulk structure of the LiMn₂O₄. TEM and XPS proved ZnO formation on the surface of the LiMn₂O₄ particles. Galvanostatic charge/discharge test and rate performance showed that the ZnO coating could improve the capacity and cycling performance of LiMn₂O₄. The 2 wt% ZnO-coated LiMn₂O₄ sample exhibited an initial discharge capacity of 112.8 mAh g^?1 with a capacity retention of 84.1 % after 500 cycles at 0.5 C. Besides, a good rate capability at different current densities from 0.5 to 5.0 C can be acquired. CV and EIS measurements showed that the ZnO coating effectively reduced the impacts of polarization and charge transfer resistance upon cycling.