Structural and electrical properties of KCa<Subscript>2</Subscript>Nb<Subscript>5</Subscript>O<Subscript>15</Subscript> ceramics

A polycrystalline sample of KCa₂Nb₅O₁₅ with tungsten bronze structure was prepared by a mixed oxide method at high temperature. A preliminary structural analysis of the compound showed an orthorhombic crystal structure at room temperature. Surface morphology of the compound shows a uniform grain distribution throughout the surface of the sample. Studies of temperature variation on dielectric response at various frequencies show that the compound has a transition temperature well above the room temperature (i.e., 105°C), which was confirmed by the polarization measurement. Electrical properties of the material have been studied using a complex impedance spectroscopy (CIS) technique in a wide temperature (31–500°C) and frequency (10²–10⁶ Hz) range that showed only bulk contribution and non-Debye type relaxation processes in the material. The activation energy of the compound (calculated from both the loss and modulus spectrum) is same, and hence the relaxation process may be attributed to the same type of charge carriers. A possible ‘hopping’ mechanism for electrical transport processes in the system is evident from the modulus analysis. A plot of dc conductivity (bulk) with temperature variation demonstrates that the compound exhibits Arrhenius type of electrical conductivity.      

Temperature dependence of the magnetic properties and magnetoimpedance of nanocrystalline Fe<Subscript>73.5</Subscript>Si<Subscript>16.5</Subscript>B<Subscript>6</Subscript>Nb<Subscript>3</Subscript>Cu<Subscript>1</Subscript> ribbons

The temperature dependences of the magnetic properties and the magnetoimpedance effect of soft magnetic nanocrystalline Fe_73.5Si_16.5B₆Nb₃Cu₁ alloy ribbons are studied in the temperature range 24–160°C. A high temperature sensitivity of the impedance and the magnetoimpedance effect of the ribbons are detected in the ac frequency range 0.1–50 MHz. At an ac frequency of 50 MHz, the change in the impedance reaches 0.2 Ω/°C (0.5%/°C) in the temperature range 85–160°C. When the temperature increases, a monotonically decreasing character of the dependence of the magnetoimpedance effect on the applied magnetic field changes into a dependence having an increasing initial segment. The effect of temperature on the magnetoimpedance properties of the soft magnetic nanocrystalline ribbons is shown to result from temperature-induced changes in their electrical conductivity, magnetization, and effective magnetic anisotropy.     

Impedance spectroscopy of vanadium modified BaBi<Subscript>2</Subscript>Nb<Subscript>2</Subscript>O<Subscript>9</Subscript> ceramics

In recent years a wide range of Aurivillius layered materials have been introduced. These novel materials are produced in many various forms such as fibers, thin films as well as bulk by using a number of processing routes. As advanced materials they are they have many interesting properties which include a number of useful electrical properties related to separated grain and grain boundary conductivity, impedance, activation energies, etc. In this paper these properties are described and discussed in detail. The electrical properties of the vanadium doped BaBi₂Nb₂O₉ ceramic was measured over a wide range of temperatures by impedance spectroscopy (IS). The separated grain activation energy, calculated from Arrhenius characteristics at temperatures between room temperature and 600 °C, was 1 eV for 0 at.% of vanadium dopant and 1.2 eV for 10 at.%, whereas the activation energies in the grain boundary region were 0.97 and 1.15 eV, respectively. The obtained results suggest the significant role of vanadium dopant, causing ordering the crystalline structure.     

Effect of calcination conditions on lithium conductivity in Li<Subscript>1.3</Subscript>Ti<Subscript>1.7</Subscript>Al<Subscript>0.3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript> prepared by sol-gel route

In order to study the influence of powder calcination temperature on lithium ion conductivity, synthesized Li_1.3Ti_1.7Al_0.3(PO₄)₃ (LATP) was calcined at temperatures between 750 and 900 °C. The shape and size of the particles were characterized employing scanning electron microscopy (SEM), and specific surface area of the obtained powder was measured. The crystallinity grade of different heat-treated powders was calculated from XRD spectra. Posteriorly, all powders were sintered at 1100 °C employing field-assisted sintering (SPS), and the electrical properties were correlated to the calcination conditions. The highest ionic conductivity was observed for samples made out of powders calcined at 900 °C.     

Impedance spectroscopy study of Na<Subscript>1/2</Subscript>Sm<Subscript>1/2</Subscript>TiO<Subscript>3</Subscript> ceramic

Complex impedance analysis of a valence-compensated perovskite ceramic oxide Na_1/2Sm_1/2TiO₃, prepared by a mixed oxide (solid-state reaction) method, has been carried out. The formation of single-phase material was confirmed by X-ray diffraction studies, and it was found to be an orthorhombic phase at room temperature. In a scanning electron microscope, grains separated by well-defined boundaries are visible, which is in good agreement with that of impedance analysis. Alternating current impedance measurements were made over a wide temperature range (31–400 °C) in an air atmosphere. Complex impedance and modulus plots helped to separate out the contributions of grain and grain boundaries to the overall polarization or electrical behavior. The physical structure of the samples was visualized most prominently at higher temperatures (275 °C) from the Nyquist plots showing inter- and intragranular impedance present in the material. The frequency dependence of electrical data is also analyzed in the framework of the conductivity and modulus formalisms. The bulk resistance, evaluated from the impedance spectrum, was observed to decrease with rise in temperature, showing a typical negative temperature coefficient of resistance-type behavior like that of semiconductors. The modulus mechanism indicates the non-Debye type of conductivity relaxation in the materials, which is supported by the impedance data. PACS 77.22.Ch; 77.22.Ej; 77.22.Gm; 77.22.Jp; 77.84.Bw     

Low-temperature anomaly of the magnetization in alloys (Pr,Dy,<Emphasis Type="Italic">M</Emphasis>)<Subscript>2</Subscript>(Fe,Co)<Subscript>14</Subscript>B (<Emphasis Type="Italic">M</Emphasis> = Gd,Sm, Nd)

It has been found that temperature dependences of the saturation magnetization of sintered hard magnetic (Pr,Dy,M)₂(Fe,Co)₁₄B (M = Gd, Sm, Nd) alloys demonstrate an increase at a temperature lower than a critical temperature (150 K for Sm and Nd and 70 K for Gd). An additive of copper does not influence the critical temperature. It has been assumed that there is a low-temperature phase in which cobalt is replaced with boron that diffuses from the (Pr,Dy,Gd)(Fe,Co)₄B phase to the near-surface region of grains of the main magnetic (Pr,Dy,Gd)₂(Fe,Co)₁₄B phase.     

Incorporation of NH<Subscript>4</Subscript>NO<Subscript>3</Subscript> into MC-PVA blend-based polymer to prepare proton-conducting polymer electrolyte films

Proton-conducting solid polymer blend electrolytes based on methylcellulose-polyvinyl alcohol:ammonium nitrate (MC-PVA:NH₄NO₃) were prepared by the solution cast technique. The structural and electrical properties of the samples were examined by X-ray diffraction (XRD), Fourier transform infrared (FTIR), and electrical impedance (EI) spectroscopy. The shifting and change in the intensity of FTIR bands of the electrolyte samples confirm the complex formation between the MC-PVA polymer blend and the NH₄NO₃ added salt. The observed broadening in the XRD pattern of the doped samples reveals the increase of the amorphous fraction of polymer electrolyte samples. The increase in electrical conductivity of polymer electrolyte samples with increasing salt concentration attributed to the formation of charge-transfer complexes, and to increase in the amorphous domains. A maximum ionic conductivity of about 7.39 × 10^?5 S cm^?1 was achieved at room temperature for the sample incorporating 20 wt% of NH₄NO₃. The DC conductivity of the present polymer system exhibits Arrhenius-type dependence with temperature. The decrease in the values of activation energies with increasing salt concentration indicates the ease mobility of ions. The decrease in dielectric constant with increasing frequency was observed at all temperatures. Optical properties such as absorption edge, optical band gap, and tail of localized state were estimated for polymer blend and their electrolyte films. It was found that the optical band gap values shifted towards lower photon energy from 6.06 to 4.75 eV by altering the NH₄NO₃ salt content.     

Effect of a Rare-Earth Ion on the Structural Instability in RFe<Subscript>3</Subscript>(BO<Subscript>3</Subscript>)<Subscript>4</Subscript> Crystals

The dynamics of the crystal lattice of RFe₃(BO₃)₄ (R = Pr, Nd, Sm, Gd, Tb, Dy, and Ho) compounds in the high-symmetry R32 phase has been calculated. Significant changes in spectra of compounds with various rare-earth ions have been obtained only near the edge Λ point of the Brillouin zone (qΛ = 1/3(?2b₁ + b₂ + b₃, where b₁, b₂, and b₃ are the reciprocal lattice vectors) for acoustic oscillation branches. A decrease in the frequency of an acoustic mode at the point Λ has been revealed in all studied compounds. This frequency depends on the type of rare-earth ion and decreases from a compound with Pr to a compound with Ho down to imaginary values. Such a behavior of the frequency of the unstable acoustic mode is in good agreement with experimental data on the dependence of the temperature of the R32 → P3₁21 structural phase transition on the type of rare-earth ion in ferroborates.     

Effect of trivalent rare earth doping on magnetic and magnetocaloric properties of Pr<Subscript>0.5</Subscript>(Ce,Eu,Y)<Subscript>0.1</Subscript>Sr<Subscript>0.4</Subscript>MnO<Subscript>3</Subscript> manganites

Experimental studies of the structural, magnetic and magnetocaloric properties of the three compounds Pr_0.5X_0.1Sr_0.4MnO₃ (X = Ce, Eu and Y) are reported. Our samples were synthesized using the Pechini sol–gel method. X-ray powder diffraction at room temperature indicates that our materials crystallize in the orthorhombic structure with Pbnm space group. The compounds undergo a second-order magnetic transition from paramagnetic to ferromagnetic state around their own Curie temperatures T _C ~ 310, 270 and 230 K for X = Ce, Eu and Y, respectively. A considerable magnetocaloric effect (MCE) is observed around room temperature. The maximum values of magnetic entropy change ?S _max are 3.54, 3.81 and 2.99 J/kgK for the samples with X = Ce, Eu and Y, respectively, when a magnetic field of 5 T was applied. The relative cooling power (RCP) values for the corresponding materials are 246.60, 261.66 and 298 J/kg. It is shown that for Pr_0.5X_0.1Sr_0.4MnO₃ the exponent n and the magnetic entropy change follow a master curve behavior. With the universal scaling curve, the experimental ?S at several temperatures and fields can be extrapolated.     

High-temperature complex impedance and modulus spectroscopic studies of doped Na<Subscript>0.5</Subscript>Bi<Subscript>0.5</Subscript>TiO<Subscript>3</Subscript>-BaTiO<Subscript>3</Subscript> ferroelectric ceramics

Lead-free Na_0.5Bi_0.5TiO₃ (NBT) and (1 ? x)Na_0.5Bi_0.5TiO₃ + xBaTiO₃ with x = 0.1 and 0.2 (where x = 0.1 and 0.2 are named as NBT1 and NBT2, respectively), (1 ? y)Na_0.5Bi_0.5TiO₃ + yBa_0.925Nd_0.05TiO₃ with y = 0.1 and 0.2 (where y = 0.1 and 0.2 are named as NBT3 and NBT4, respectively)-based relaxor ferroelectric ceramics were prepared using the sol-gel method. The crystal structure was investigated by X-ray diffraction (XRD) at room temperature (RT). The XRD patterns confirmed the presence of the rhombohedral phase in all the samples. The electrical properties of the present NBT-based samples were investigated by complex impedance and the modulus spectroscopy technique in the temperature range of RT–600 °C. The AC conductivity was found to increase with the substitution of Ba²⁺ ions to the NBT sample whereas it significantly decreased with the addition of Nd³⁺ ions. The more anion vacancies in Ba-added samples and the lower anion vacancies in Nd-added samples were found to be responsible for higher and lower conductivities, respectively.     

Impedance spectroscopy analysis of Li<Subscript>2</Subscript>SnO<Subscript>3</Subscript>

In this work, Li₂SnO₃ has been synthesized by the sol–gel method using acetates of lithium and tin. Thermogravimetric analysis (TGA) has been applied to the precursor of Li₂SnO₃ to determine the suitable calcination temperature. The formation of the compound calcined at 800 °C for 9 h has been confirmed by X-ray diffraction (XRD) analysis. The Li₂SnO₃ is then pelletized and electrically characterized by using electrochemical impedance spectroscopy (EIS) in the frequency range from 50 Hz to 1 MHz. The complex impedance spectra clearly show the dominating presence of the grain boundary effect on electrical properties whereas the complex modulus plots reveal two semicircles which are due to the grain (bulk) and grain boundary. The spectra of imaginary parts of both impedance and modulus versus frequency show the existence of peaks with the modulus plots exhibiting two peaks that are ascribed to the grain and grain boundary of the material. The peak maximum shifts to higher frequency with an increase in temperature and the broad nature of the peaks indicates the non-Debye nature of Li₂SnO₃. The activation energy associated with the dielectric relaxation obtained from the electrical impedance spectra is 0.67 eV. From the electric modulus spectra, the activation energies related to conductivity relaxation in the grain and grain boundary of Li₂SnO₃ are 0.59 and 0.69 eV, respectively. The conductivity–temperature relationship is thermally assisted and obeys the Arrhenius rule with the activation energy of 0.66 eV. The conduction mechanism of Li₂SnO₃ is via hopping.     

Metal-insulator transition in a radiation-disordered La<Subscript>0.85</Subscript>Sr<Subscript>0.15</Subscript>MnO<Subscript>3</Subscript> manganite

The temperature dependences of the electrical resistivity ρ(T) and the ac magnetic susceptibility χ(T, H = 0) are thoroughly investigated for a perovskite-like lanthanum manganite, namely, La_0.85Sr_0.15MnO₃, which is preliminarily exposed to neutron irradiation with a fluence _F = 2 × 10¹⁹ cm^?2 and then annealed at different temperatures ranging from 200 to 1000°C. The results of the electrical resistance measurements demonstrate that neutron irradiation of the samples leads to the disappearance of the low-temperature insulating phase. As the annealing temperature increases, the insulating phase is not restored and the manganite undergoes a transformation into a metallic phase. Analysis of the magnetic properties shows that, under irradiation, the ferromagnet-paramagnet phase transition temperature T_C decreases and the magnetic susceptibility is reduced significantly. With an increase in the annealing temperature, the phase transition temperature T_C and magnetic susceptibility χ(_{T, H} = 0) increase and gradually approach values close to those for an unirradiated sample. This striking difference in the behavior of the electrical and magnetic properties of the radiation-disordered La_0.85Sr_0.15MnO₃ manganite is explained qualitatively.     

Synthesis,sintering, and conductivity of Mn<Subscript>2</Subscript>V<Subscript>2</Subscript>O<Subscript>7</Subscript>

Studies on the sintering of manganese pyrovanadate depending on the temperature and the crystallite size show that we are prevented from obtaining a bulk ceramic sample by the anisotropic growth of grains. Investigation of the electrical properties of Mn₂V₂O₇ in the temperature range of 250–800°C reveals the activation energy at which bulk conductivity is 0.62 eV.     

Phase transition and electrical investigation in lithium copper pyrophosphate compound Li<Subscript>2</Subscript>CuP<Subscript>2</Subscript>O<Subscript>7</Subscript> using impedance spectroscopy

Lithium pyrophosphate compound Li₂CuP₂O₇ has been synthesized through solid state reaction method. FTIR and XRD results, realized at room temperature, indicate respectively the dominant feature of pyrophosphate anion (P₂O₇)^4? and a pure monoclinic phase with I2/a space group. Electrical and dielectric properties have been studied using impedance spectroscopy complex over a wide temperature (576–710 K) and frequency (209 Hz–1 MHz) range. From the direct and alternative conductivities (DC and AC), electrical conduction is found to be thermally activated process. The frequency-dependent AC conductivity obeys Jonscher’s universal power law σ_AC~Aω^s. The differential scanning calorimetry spectrum discloses phase transition at 622 K.     

Synthesis,thermal and electrical behavior of the superprotonic conductor phase in Rb<Subscript>3</Subscript>(HSeO<Subscript>4</Subscript>)<Subscript>2.5</Subscript>(H<Subscript>2</Subscript>PO<Subscript>4</Subscript>)<Subscript>0.5</Subscript> compound

The Rb₃(HSeO₄)_2.5(H₂PO₄)_0.5 compound was prepared and its thermal behavior and electric properties were investigated. The thermogravimetry (TGA) analysis and the differential scanning calorimetric (DSC) show the presence of a structural phase transition of the title compounds at 374 K which is confirmed by the variation of fp and σ_dc as a function of temperature. The complex impedance of the Rb₃(HSeO₄)_2.5(H₂PO₄)_0.5 compound has been investigated in the temperature range of 295–453 K and in the frequency range 209 Hz–1 MHz. The impedance plots show semicircle arcs at different temperatures, and an electrical equivalent circuit has been proposed to explain the impedance results. The circuits consist of the parallel combination of bulk resistance Rp and constant phase elements CPE₁ in series with fractal capacity CPE₂. The frequency dependence of the conductivity is interpreted in terms of Jonscher’s law. The conductivity dc follows the Arrhenius relation. The near value of activation energies obtained from the analysis of modulus, conductivity data, and circuit equivalent confirm that the transport is through the ion hopping mechanism, dominated by the motion of the H⁺ proton in the structure of the investigated materials.     

Electrical characterization of porous La-doped BaSnO<Subscript>3</Subscript> using impedance spectroscopy

A few compositions in the system Ba_1???x La _x SnO₃ (x?=?0.00, 0.01, 0.05, and 0.10) have been synthesized via the solid state ceramic route. The synthesized powders have been characterized using X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray analysis, Raman spectroscopy, Fourier transformation infrared, thermogravimetrical analysis, and differential thermal analysis techniques. The powder X-ray diffraction pattern of the samples confirms the formation of a single-phase solid solution only up to 0.50?≤?x. It was found that all the samples have a cubic crystal structure. The electrical properties of La-modified BaSnO₃ were studied using ac impedance spectroscopy technique over a wide range of temperatures (50–650 °C) in the frequency range of 10 Hz–13 MHz. The complex impedance plots above 300 °C show that total impedance is due to the contributions of grain and grain boundaries. The resistance of these contributions has been determined. Variation of these resistances with temperature shows the presence of two different regions with different slopes. The nature of the variation of conductivity of the grain and grain boundaries is different in different regions. Based on the value of activation energy, it is proposed that conduction via hopping of doubly ionized oxygen vacancies (V_O ^??) is taking place in the temperature region of 300–450 °C, whereas in the temperature region of 450–650 °C, it is due to proton, i.e., OH^? ions, hopping.     

High temperature dependence of the density of two-dimensional electron gas in Al<Subscript>0.18</Subscript>Ga<Subscript>0.82</Subscript>N/GaN heterostructures

Temperature dependence of the density of two-dimensional electron gas (2DEG) in Al_0.18Ga_0.82N/GaN heterostructures has been investigated by means of high temperature Hall measurements ranging from room temperature to 500 °C. It is found that the 2DEG density decreases with increasing temperature in the range from room temperature to 250 °C, and then increases with the temperature above 250 °C. It is thought that the decrease of the 2DEG density from room temperature to 250 °C is caused by the reduction of the conduction band offset at high temperatures. The increase of measured 2DEG density at higher temperatures is attributed to the background electron concentration in the GaN layer. Theoretical calculation of the 2DEG density in Al_0.18Ga_0.82N/GaN heterostructures at various temperatures is consistent with the experimental results using the multilayer Hall effect model. PACS 73.40.Kp; 73.61.Ey     

Temperature-controlled synthesis of Ga<Subscript>2</Subscript>O<Subscript>3</Subscript> nanobelts and nanosheets

We have investigated the effect of growth temperature on structural morphology and photoluminescence (PL) properties of as-synthesized gallium oxide (Ga₂O₃) nanostructures. The products consisted of Ga₂O₃ nanobelts and nanosheets (i.e. wider nanobelts), which had monoclinic crystalline structures. The average width of structures grown at 1000 °C was relatively greater than those at 800 °C, revealing that higher temperature favored the formation of nanosheets. PL measurements of 800 °C- and 1000 °C-grown samples indicated that both samples exhibited a broad emission band peaked around the blue-light region, while only the 800 °C-grown sample showed a red peak. PACS 81.07.-b; 81.05.Je; 61.10.Nz; 68.37.Hk; 68.37.Lp     

Thermal properties and ionic conductivity of Li<Subscript>1,3</Subscript>Ti<Subscript>1,7</Subscript>Al<Subscript>0,3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript> solid electrolytes sintered by field-assisted sintering

Li_1,3Ti_0,7Al_0,3(PO₄)₃ (LATP) powder was obtained by a conventional melt-quenching method and consolidated by field-assisted sintering technology (FAST) at different temperatures. Using this technique, the samples could be sintered to relative densities in the range of 93 to 99 % depending on the sintering conditions. Ionic and thermal conductivity were measured and the results are discussed under consideration of XRD and SEM analyses. Thermal conductivity values of 2 W/mK and ionic conductivities of 4?×?10^?4 Scm^?1 at room temperature were obtained using relatively large particles and a sintering temperature of 1000 °C at an applied uniaxial pressure of 50 MPa.     

Studies on structural and electrical properties of Mg<Subscript>0. 5+y</Subscript> (Zr<Subscript>2-y</Subscript>Fe<Subscript>y</Subscript>) <Subscript>2</Subscript> (PO<Subscript>4</Subscript>) <Subscript>3</Subscript> ceramic electrolytes

The sample of Mg_{0. 5+y} (Zr_1-y Fe_y) ₂ (PO₄) ₃ (0.0 ≤y ≤0.5) was synthesized using the sol-gel method. The structures of the samples were investigated using X-ray diffraction and Fourier transform infrared spectroscopy measurement. XRD studies showed that samples had a monoclinic structure which was iso-structured with the parent compound, Mg_0.5Zr (PO₄) ₃. The complex impedance spectroscopy was carried out in the frequency range 1–6 MHz and temperature range 303 to 773 K to study the electrical properties of the electrolytes. The substitutions of Fe³⁺ with Zr⁴⁺ in the Mg_0.5Zr (PO₄) ₃ structure was introduced as an extrainterstitial Mg²⁺ ion in the modified structured. The compound of Mg_0.5+y (Zr_1-y Fe_y)₂(PO₄)₃ with y?=?0.4 gives a maximum conductivity value of 1.25?×?10^?5 S cm^?1 at room temperature and 7.18?×?10^?5 S cm^?1 at 773 K. Charge carrier concentration, mobile ion concentration, and ion hopping rate are calculated by fitting the conductance spectra to power law variation, σ _ac (ω)?=?σ _o ? +?Aω ^α . The charge carrier concentration and mobile ion concentration increases with increase of Fe³⁺ inclusion. This implies the increase in conductivity of the compounds was due to extra interstitial Mg²⁺ ions.