High-temperature complex impedance and modulus spectroscopic studies of doped Na<Subscript>0.5</Subscript>Bi<Subscript>0.5</Subscript>TiO<Subscript>3</Subscript>-BaTiO<Subscript>3</Subscript> ferroelectric ceramics

Lead-free Na_0.5Bi_0.5TiO₃ (NBT) and (1 ? x)Na_0.5Bi_0.5TiO₃ + xBaTiO₃ with x = 0.1 and 0.2 (where x = 0.1 and 0.2 are named as NBT1 and NBT2, respectively), (1 ? y)Na_0.5Bi_0.5TiO₃ + yBa_0.925Nd_0.05TiO₃ with y = 0.1 and 0.2 (where y = 0.1 and 0.2 are named as NBT3 and NBT4, respectively)-based relaxor ferroelectric ceramics were prepared using the sol-gel method. The crystal structure was investigated by X-ray diffraction (XRD) at room temperature (RT). The XRD patterns confirmed the presence of the rhombohedral phase in all the samples. The electrical properties of the present NBT-based samples were investigated by complex impedance and the modulus spectroscopy technique in the temperature range of RT–600 °C. The AC conductivity was found to increase with the substitution of Ba²⁺ ions to the NBT sample whereas it significantly decreased with the addition of Nd³⁺ ions. The more anion vacancies in Ba-added samples and the lower anion vacancies in Nd-added samples were found to be responsible for higher and lower conductivities, respectively.     

Study on electrochemical performance of Mg-doped Li<Subscript>2</Subscript>FeSiO<Subscript>4</Subscript> cathode material for Li-ion batteries

In this paper, Li₂Fe_1?yMg_ySiO₄/C (y?=?0, 0.01, 0.02, 0.03, 0.05), a cathode material for lithium-ion battery was synthesized by solid-state method and modified by doping Mg²⁺ on the iron site. The effects of Mg²⁺ doping on the crystal structure and electrochemical performance Li₂FeSiO₄ was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), and electrochemical tests. Electrochemical methods of measurement were applied including constant current charge–discharge test, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS), to determine the electrochemical performance of the material and the optimal doping ion and ratio. The results showed that Li₂Fe_0.98Mg_0.02SiO₄/C has the higher specific capacity and better cycle stability as well as lower impedance and better reversibility. The enhanced electrochemical performance can be attributed to the increased electronic conductivity, the decreased charge transfer impedance, and the improved Li-ion diffusion coefficient. Then, further study on the synthesis conditions was performed to find the optimal combustion temperature and time. According to the study, the material which has the best electrochemical performance, shows initial discharge specific capacity of 142.3 mAh g^?1 at 0.1 C (1 C?=?166 mA g^?1) and coulomb efficiency of 95.6%, under the condition that the temperature is 700 °C and the calcining time is 10 h.     

Spin-spin interaction and the EPR spectrum of KDy(WO<Subscript>4</Subscript>)<Subscript>2</Subscript>

The EPR spectrum of a KDy(WO₄)₂ monoclinic crystal is investigated. It is found that the EPR spectrum of magnetically concentrated materials at a low frequency (9.2 GHz) undergoes a substantial transformation in addition to the well-known broadening of the EPR lines. At low Dy³⁺ concentrations (x<10^?2), the EPR spectrum of an isomorphic crystal, namely, KY_(1?x)Dy_x(WO₄)₂, is characterized by the parameters g_x=0, g_y=1.54, and g_z=14.6. For a magnetically concentrated crystal KDy(WO₄)₂, the g values are as follows: g_x=0, g_y=0.82, and g_z=2.52. It is demonstrated that the difference in the parameters is associated with the specific spin-spin interaction between Dy³⁺ ions, including the Dzyaloshinski interaction, which is not observed at high frequencies.     

Comparative study of solid-state reaction and sol-gel process for synthesis of Zr-doped Li<Subscript>0.5</Subscript>La<Subscript>0.5</Subscript>TiO<Subscript>3</Subscript> solid electrolytes

We investigated the synergistic influences of synthesis methods (solid-state reaction vs. sol-gel process) and Zr⁴⁺ doping on the structure and ionic conductivity of perovskite-structured Li_0.5La_0.5TiO₃ (LLTO) solid electrolytes. The lithium-ion conductivity of Li_0.5La_0.5Ti_1???x Zr _x O₃ ceramic specimens was evaluated as a function of x value and compared carefully between those two synthesis methods. Regarding the conductivity, sol-gel process is better for the synthesis of LLTO than solid-state reaction. As a result, the highest grain conductivity is obtained in the sol-gel-derived pure LLTO sample with x?=?0, reaching 1.10?×?10^?3 S?·?cm^?1. Partial substitution of Zr⁴⁺ enlarges the LLTO’s grain aggregate size and increases the total superficial area of aggregates. Consequently, Zr⁴⁺ substitution not only affects the grain (bulk) conductivity, but more importantly, also improves the grain boundary conductivity and the total conductivity. The highest total conductivity is 5.84?×?10^?5 S?·?cm^?1 with x?=?0.04 by sol-gel process.     

Lithium diffusion in Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>-based electrodes: a joint analysis of electrochemical impedance,cyclic voltammetry,pulse chronoamperometry,and chronopotentiometry data

In order to establish the mechanism and to determine the parameters of lithium transport in electrodes based on lithium-vanadium phosphate (Li₃V₂(PO₄)₃), the kinetic model was designed and experimentally tested for joint analysis of electrochemical impedance (EIS), cyclic voltammetry (CV), pulse chronoamperometry (PITT), and chronopotentiometry (GITT) data. It comprises the stages of sequential lithium-ion transfer in the surface layer and the bulk of electrode material’s particles, including accumulation of lithium in the bulk. Transfer processes at both sites are of diffusion nature and differ significantly, both by temporal (characteristic time, τ) and kinetic (diffusion coefficient, D) constants. PITT data analysis provided the following D values for the predominantly lithiated and delithiated forms of the intercalation material: 10^?9 and 3 × 10^?10 cm² s^?1, respectively, for transfer in the bulk and 10^?12 cm² s^?1 for transfer in the thin surface layer of material’s particles. D values extracted from GITT data are in consistency with those obtained from PITT: 3.5–5.8 × 10^?10 and 0.9–5 × 10^?10 cm² s^?1 (for the current and currentless mode, respectively). The D values obtained from EIS data were 5.5 × 10^?10 cm² s^?1 for lithiated (at a potential of 3.5 V) and 2.3 × 10^?9 cm² s^?1 for delithiated (at a potential 4.1 V) forms. CV evaluation gave close results: 3 × 10^?11 cm² s^?1 for anodic and 3.4 × 10^?11 cm² s^?1 for cathodic processes, respectively. The use of complex experimental measurement procedure for combined application of the EIS, PITT, and GITT methods allowed to obtain thermodynamic E,c dependence of Li₃V₂(PO₄)₃ electrode, which is not affected by polarization and heterogeneity of lithium concentration in the intercalate.     

Characteristics of the Li<Superscript>+</Superscript>-Ion Conductivity of Li<Subscript>3</Subscript>R<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript> Crystals (R = Fe,Sc) in the Superionic State

The characteristics of Li+-ion conductivity σdc of structural γ modifications of Li₃R₂(PO₄)₃ compounds (R = Fe, Sc) existing in the superionic state have been investigated by impedance spectroscopy. The type of structural framework [R₂P₃O₁₂]_∞^3- affects the σdc value and the σdc activation enthalpy in these compounds. The ion transport activation enthalpy in γ-Li₃R₂(PO₄)₃ (ΔH_σ = 0.31 ± 0.03 eV) is lower than in γ-Li₃Fe₂(PO₄)₃ (ΔH_σ = 0.36 ± 0.03 eV). The conductivity of γ-Li₃Fe₂(PO₄)₃ (σ_dc = 0.02 S/cm at 573 K) is twice as high as that of γ-Li₃R₂(PO₄)₃. A decrease in temperature causes a structural transformation of Li₃R₂(PO₄)₃ from the superionic γ modification (space group Pcan) through the intermediate metastable β modification (space group P2₁/n) into the “dielectric” α modification (space group P2₁/n). Upon cooling, σdc for both phosphates decreases by a factor of about 100 at the superionic TSIC transition. In Li₃Fe₂(PO₄)₃ σdc gradually decreases in the temperature range T_SIC = 430–540 K, whereas in Li₃R₂(PO₄)₃ σdc undergoes a jump at T_SIC = 540 ± 25 K. Possible crystallochemical factors responsible for the difference in the σdc and ΔH_σ values and the thermodynamics and kinetics of the superionic transition for Li₃R₂(PO₄)₃ are discussed.     

Investigation on lithium ion conductivity and structural stability of yttrium-substituted Li<Subscript>7</Subscript>La<Subscript>3</Subscript>Zr<Subscript>2</Subscript>O<Subscript>12</Subscript>

Advanced Li-air battery architecture demands a high Li⁺ conductive solid electrolyte membrane that is electrochemically stable against metallic lithium and aqueous electrolyte. In this work, an investigation has been carried out on the microstructure, Li⁺ conduction behaviour and structural stability of Li₇La_3-x Y _x Zr₂O₁₂ (x = 0.125, 0.25 and 0.50) prepared by conventional solid-state reaction technique. The phase analysis of Li₇La_3-x Y _x Zr₂O₁₂ (x = 0.125, 0.25 and 0.50) sintered at 1200 °C by powder X-ray diffraction (PXRD) and Raman confirms the formation of high Li⁺ conductive cubic phase (\( Ia\overline{3}d \)) lithium garnets. Among the investigated lithium garnets, Li₇La_2.75Y_0.25Zr₂O₁₂ sintered at 1200 °C exhibits a maximized room temperature total (bulk + grain boundary) Li⁺ conductivity of 3.21 × 10^?4 S cm^?1 along with improved relative density of 96 %. The preliminary investigation on the structural stability of Li₇La_2.75Y_0.25Zr₂O₁₂ in the solutions of 1 M LiCl, dist. H₂O and 1 M LiOH at 30 °C/50 °C indicates that the Li₇La_2.75Y_0.25Zr₂O₁₂ is relatively stable against 1 M LiCl and dist. H₂O. Further electrochemical investigation is essential for practical application of Li₇La_2.75Y_0.25Zr₂O₁₂ as protective solid electrolyte membrane in aqueous Li-air battery.     

Linear and nonlinear optical spectroscopy of gadolinium iron borate GdFe<Subscript>3</Subscript>(BO<Subscript>3</Subscript>)<Subscript>4</Subscript>

The optical spectra and the second-harmonic generation (SHG) are studied in a noncentrosymmetric GdFe₃(BO₃)₄ magnet. In the region of weak absorption (α～20–400 cm^?1) below ～3 eV, three absorption bands are distinguished, which can be unambiguously assigned to forbidden electronic transitions from the ground ⁶A₁ state of the Fe³⁺ ion to its excited states ⁴T₁(～1.4 eV), ⁴T₂(～2 eV), and ⁴A₁, ⁴E(～2.8 eV). Intense absorption begins in the region above 3 eV (α～2–4×10⁵ cm^?1), where two bands at ～4.0 and 4.8 eV are observed, which are caused by allowed electric dipole charge-transfer transitions. The spectral features of SHG in the 1.2–3.0-eV region are explained by a change in the SHG efficiency caused by a change in the phase mismatch. It is shown that in the weak absorption region, phase matching can be achieved for SHG.     

Conduction through localized states in a single crystal of the TlGa<Subscript>0.5</Subscript>Fe<Subscript>0.5</Subscript>Se<Subscript>2</Subscript> alloy

Layered single crystals of the TlGa_0.5Fe_0.5Se₂ alloy in a dc electric field at temperatures ranging from 128 to 178 K are found to possess variable-range-hopping conduction along natural crystal layers through states localized in the vicinity of the Fermi level. The parameters characterizing the electrical conduction in the TlGa_0.5Fe_0.5Se₂ crystals are estimated as follows: the density of states near the Fermi level N_F = 2.8 × 10¹⁷ eV^?1 cm^?3, the spread in energy of these states ΔE = 0.13 eV, the average hopping length R_av = 233 Å, and the concentration of deep-lying traps N _t = 3.6 × 10¹⁶ cm^?3.     

Gas release in the process of thermal treatment of sputtered Pb(Ti<Subscript>0.48</Subscript>Zr<Subscript>0.52</Subscript>)O<Subscript> <Emphasis Type="Italic">x</Emphasis> </Subscript> films

The conditions (regimes of deposition and thermal treatment) for gas bubble formation in ferroelectric Pb(Ti_1–yZr_y)O₃ films have been determined by thermal desorption and electron and optical micros-copy. A mechanism of bubble formation has been proposed. This mechanism rests upon the notion that lead can form oxides of the PbO₂ type with a high oxygen content at relatively low temperatures and that these oxides break down with the release of oxygen to lower oxides of the PbO type upon subsequent heating. These ideas have been taken as the basis of a technique for the fabrication of Pb(Ti_1–yZr_y)O₃ films with a reduced (by an order of magnitude) density of through defects.     

Antisite defects and valence state of vanadium in Na<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>

Electron paramagnetic resonance (EPR) studies have been performed with the aim of determining the valence state and local crystal structure of the nearest environment of vanadium ions in the initial, charged, and discharged samples of the cathode material Na_xV₂(PO₄)₃ (1 ≤ x ≤ 3). It has been found that the charged sample (x = 1) is characterized by an intense signal corresponding to V⁴⁺ ions located in a highly distorted octahedral crystal field. An EPR signal with the g-factor close to the g-factor of the V⁴⁺ ion has also been observed in the initial sample (x = 3), where the intensity of the resonance signal is one order of magnitude lower than that in the charged sample. It has been revealed that the resonance signal under consideration is associated with the formation of antisite defects when a part of vanadium ions are located in sites of sodium ions. It has also been found that the intensity of this signal increases after a complete charge–discharge cycle (x = 3).     

Structural and magnetic phase transformations in the BiFeO<Subscript>3</Subscript>-CaFe<Subscript>0.5</Subscript>Nb<Subscript>0.5</Subscript>O<Subscript>3</Subscript> system

The crystal structure and magnetic properties of the Bi_{1 ? x} Ca _x Fe_{1 ? x/2}Nb _x/2O₃ system were studied. It is shown that, at x ≤ 0.15, the unit-cell symmetry of solid solutions is rhombohedral (space group R3c). Solid solutions with x ≥ 0.3 have an orthorhombic unit cell (space group Pbnm). The rhombohedral compositions are antiferromagnetic, while the orthorhombic compositions exhibit a small spontaneous magnetization due to Dzyaloshinski?-Moriya interaction. In CaFe_0.5Nb_0.5O₃, the Fe³⁺ and Nb⁵⁺ ions are partially ordered and the unit cell is monoclinic (space group P2₁/n). In the concentration range 0.15 < x < 0.30, a two-phase state (R3c + Pbnm) is revealed.     

Relaxation phenomena in TlGa<Subscript>0.99</Subscript>Fe<Subscript>0.01</Subscript>Se<Subscript>2</Subscript> single crystals

The relaxation electronic phenomena occurring in TlGa_0.99Fe_0.01Se₂ single crystals in an external dc electric field are investigated. It is established that these phenomena are caused by electric charges accumulated in the single crystals. The charge relaxation at different electric field strengths and temperatures, the hysteresis of the current-voltage characteristic, and the electric charge accumulated in the TlGa_0.99Fe_0.01Se₂ single crystals are consistent with the relay-race mechanism of transfer of a charge generated at deep-lying energy levels in the band gap due to the injection of charge carriers from the electric contact into the crystal. The parameters characterizing the electronic phenomena observed in the TlGa_0.99Fe_0.01Se₂ single crystals are determined to be as follows: the effective mobility of charge carriers transferred by deep-lying centers μ_f=5.6×10^?2 cm²/(V s) at 300 K and the activation energy of charge transfer ΔE=0.54 eV, the contact capacitance of the sample C _c =5×10^?8 F, the localization length of charge carriers in the crystal d _c =1.17×10^?6 cm, the electric charge time constant of the contact τ=15 s, the time a charge carrier takes to travel through the sample t _t =1.8×10^?3 s, and the activation energy of traps responsible for charge relaxation ΔE _σ = ΔE _Q = 0.58 eV.     

Electrospun Dy-doped SrFe<Subscript>12</Subscript>O<Subscript>19</Subscript> nanofibers: microstructure and magnetic properties

SrDy _x Fe_12?x O₁₉ (x ≤ 0.08) nanofibers have been synthesized by the electrospinning method followed by calcinations process. The partial substitution of rare earth ions Dy³⁺ (10.5 μ _B of magnetic moments) mainly occupying 12k sublattice sites in the SrFe₁₂O₁₉ crystal structure is investigated and discussed in this work. An enhanced coercivity of 7155 Oe has been obtained when the doped content reached to 0.08 at a relative low calcination temperature of 800 °C. As a result, we believe the synthesized SrDy _x Fe_12?x O₁₉ nanofibers can potentially be useful in high-density recording media as well as permanent magnets.     

Substitution effects on the bulk and surface properties of (Li,Ni)Mn<Subscript>2</Subscript>O<Subscript>4</Subscript>

Manganese oxides of spinel structure, LiMn₂O₄, Li_1-x Ni _x Mn₂O₄ (0.25 ≤ x≤ 0.75), and NiMn₂O₄, were studied by EDS, XRD, SEM, magnetic (M-H, M-T), and XPS measurements. The samples were synthesized by an ultrasound-assisted sol-gel method. EDS analysis showed good agreement with the formulations of the oxides. XRD and Rietveld refinement of X-ray data indicate that all samples crystallize in the Fd3m space group characteristic of the cubic spinel structure. The a-cell parameter ranges from a = 8.2276 Å (x = 0) to a = 8.3980 Å (x = 1). SEM results showed particle agglomerates ranging in size from 2.3 μm (x = 0) down to 0.8 μm (x = 1). Hysteresis magnetization vs. applied field curves in the 5–300K range was recorded. ZFC-FC measurements indicate the presence of two magnetic paramagnetic-ferrimagnetic transitions. The experimental Curie constant was found to vary from 5 to 7.1 cm³ K mol^?1 for the range of compositions studied (0 ≤ x ≤ 1). XPS studies of these oxides revealed the presence of Ni²⁺, Mn³⁺, and Mn⁴⁺. The experimental Ni/Mn atomic ratios obtained by XPS were in good agreement with the nominal values. A linear relationship of the average oxidation state of Mn with Ni content was observed. The oxide’s cation distributions as a function of Ni content from x = 0 ?Li⁺[Mn³⁺Mn⁴⁺]O₄ to x = 1 \( {\mathrm{Ni}}_{0.35}^{2+}{\mathrm{Mn}}_{0.65}^{3+}\left[{\mathrm{Ni}}_{0.65}^{2+}\right.\left.{\mathrm{Mn}}_{1.35}^{3+}\right]{\mathrm{O}}_4 \) were proposed.     

Intrinsic superconducting transport properties of ultra-thin Fe<Subscript>1+<Emphasis Type="Italic">y</Emphasis></Subscript>Te<Subscript>0.6</Subscript>Se<Subscript>0.4</Subscript> microbridges

We investigated the superconducting properties of Fe_1+y Te_0.6Se_0.4 single-crystalline microbridges with a width of 4 μm and thicknesses ranging from 20.8 to 136.2 nm. The temperature-dependent in-plane resistance of the bridges exhibited a type of metal-insulator transition in the normal state. The critical current density (J _c) of the microbridge with a thickness of 136.2 nm was 82.3 kA/cm² at 3K and reached 105 kA/cm² after extrapolation to T = 0 K. The current versus voltage characteristics of the microbridges showed a Josephson-like behavior with an obvious hysteresis. These results demonstrate the potential application of ultra-thin Fe-based microbridges in superconducting electronic devices such as bolometric detectors.     

Properties of Ca-containing LiCoPO<Subscript>4</Subscript>-graphitic carbon foam composites

LiCo_1???x Ca _x PO₄–graphitic carbon foam composites are prepared using a sol–gel method. The structural analysis reveals LiCoPO₄ as major crystalline phase and Co₂P₂O₇ (for x?=?0.0) and Co₂P, Li₃PO₄, and (Ca,Co)₃(PO₄)₂ (for x?≥?0.05) as secondary phases. The morphology consists of microcrystalline “islands” with acicular crystallites (5–50 μm size). Transmission electron microscopy (TEM) of the powders showed that the Ca is incorporated into the crystal structure evoking exaggerated grain growth. The voltammetric profiles show a decrease of the voltammetric surface between anodic and cathodic sweeps and a shift of the reduction potentials toward higher values (～4.6 V, x?=?0.1). The electrochemical measurements, at a discharge rate of C/10 (room temperature), show an increase of the discharge-specific capacity from 100 mAhg^?1 for x?=?0.0 to 104 mAhg^?1 for x?=?0.1. The ac impedance spectroscopy data revealed an improvement of the Li-ion conductivity at high content of Ca ions (x?=?0.1).     

Acoustic emission and thermal expansion of Pb(Mg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>)O<Subscript>3</Subscript> and Pb(Mg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>)O<Subscript>3</Subscript>-PbTiO<Subscript>3</Subscript> crystals

The temperature dependence of the elongation per unit length for Pb(Mg_1/3Nb_2/3)O₃ crystals unannealed after growth and mechanical treatment is investigated in the course of thermocycling. It is revealed that this dependence deviates from linear behavior at temperatures below 350°C. The observed deviation is characteristic of relaxors, is very small in the first cycle, increases with increasing number n of thermocycles, and reaches saturation at n≥3. In the first cycle, a narrow maximum of the acoustic emission activity is observed in the vicinity of 350°C. In the course of thermocycling, the intensity of this maximum decreases and becomes zero at n>3. For (1?x)Pb(Mg_1/3Nb_2/3)O₃-xPbTiO₃ crystals, the dependence of the temperature of this acoustic emission maximum on x exhibits a minimum. It is assumed that the phenomena observed are associated with the phase strain hardening due to local phase transitions occurring in compositionally ordered and polar nanoregions.     

Pressure-induced superconductivity and structural transitions in Ba(Fe<Subscript>0.9</Subscript>Ru<Subscript>0.1</Subscript>)<Subscript>2</Subscript>As<Subscript>2</Subscript>

Electrical transport and structural characterizations of isoelectronically substituted Ba(Fe_0.9Ru_0.1)₂As₂ have been performed as a function of pressure up to ～ 30 GPa and temperature down to ～ 10 K using designer diamond anvil cell. Similar to undoped members of the AFe₂As₂ (A = Ca, Sr, Ba) family, Ba(Fe_0.9Ru_0.1)₂As₂ shows anomalous a-lattice parameter expansion with increasing pressure and a concurrent ThCr₂Si₂ type isostructural (I4/mmm) phase transition from tetragonal (T) phase to a collapsed tetragonal (cT) phase occurring between 12 and 17 GPa where the a is maximum. Above 17 GPa, the material remains in the cT phase up to 30 GPa at 200 K. The resistance measurements show evidence of pressure-induced zero resistance that may be indicative of high-temperature superconductivity for pressures above 3.9 GPa. The onset of the resistive transition temperature decreases gradually with increasing pressure before completely disappearing for pressures above ～ 10.6 GPa near the T-cT transition. We have determined the crystal structure of the high-T _c phase of Ru-doped BaFe₂As₂ to remain as tetragonal (I4/mmm) by analyzing the X-ray diffraction pattern obtained at 10 K and 9.7 ± 0.7 GPa, as opposed to inferring the structural transition from electrical resistance measurement, as in a previous report [S.K. Kim, M.S. Torikachvili, E. Colombier, A. Thaler, S.L. Bud’ko, P.C. Canfield, Phys. Rev. B 84, 134525 (2011)].     

Structural Phase Transition of Perovskite-Type N(CH<Subscript>3</Subscript>)<Subscript>4</Subscript>CdBr<Subscript>3</Subscript> Studied by MAS NMR and Static NMR

The structural geometry change in the perovskite-type N(CH₃)₄CdBr₃ single crystal near the phase transition temperature of T _C = 390 K was investigated using magic angle spinning nuclear magnetic resonance techniques. For ¹H and ¹³C nuclei, the temperature dependences of their chemical shift, spectral intensity, and spin–lattice relaxation time (T _1ρ) in the rotating frame were obtained and analyzed. While the chemical shift and T _1ρ of ¹H showed change near T _C, those of ¹³C did not. In addition, the ¹¹³Cd spin–lattice relaxation time T ₁ in the laboratory frame near T _C show no evidence of anomalous change near the phase transition temperature, which coincides with the measured changes in the ¹H T _1ρ. The driving force for this phase transition was connected to the ¹H in the CH₃ groups.