消臭抗菌纤维素纤维的制备、结构和性能

采用一种制备消臭、抗菌纤维素纤维的新方法，即先将纤维素纤维用多元羧酸进行化学修饰，然后在铜溶液中处理，生成铜螯合纤维素纤维，用红外光谱、电子自旋波谱表征了该纤维的配位结构，消臭和抗菌实验结果显示，这种功能性纤维对硫化氢，氢气、三甲胺的消臭率分别达到100％，92．1％和80．4％，对金黄色葡萄球菌，大肠杆菌和白色念珠菌的抑菌率分别为79．14％，93．59％和82．50％，用X射线衍射，电子自旋波谱分析了该纤维吸附硫化氢，氨气、三甲胺的机理。     

金属酞菁催化巯基乙醇氧化的研究

研究了２，９，１６，２３－四羧基铁（Ⅲ），钴（Ⅱ）酞菁及固载在硅胶上的２，９，１６，２３－四甲酰胺基铁（Ⅲ），钴（Ⅱ）酞菁，在水溶液中催化硫醇氧化的反应，比较了几种催化剂的性能，考察了反应条件对硫醇氧化反应的影响，提出了反应机理，结果表明，当硫醇浓度较高地，固载后的酞菁铁，其催化性能优于或接近未固载的酞菁铁；当而硫醇浓度较低时，固载后的金属酞菁显示出更接近实际的优越性，而两种金属酞菁固载后仍具有良     

温和条件下分子氧的活化和转移——Ⅱ.在1-辛烯氧化反应中酞菁铁、钴N-碱加合物的催化作用

在温和条件下,在1-辛烯氧化反应中,研究了酞菁铁、钴N-碱加合物的催化作用.发现在室温和0.1MPa的氧气氛中,在共催化剂存在时,酞菁铁、钴N-碱加合物确实具有催化分子氧活化和使其转移至烯烃的功能.酞菁铁N-碱加合物的催化活性总是高于酞菁钴的.同时,在同一中心金属离子的情况下,N-碱配体性质对催化活性有明显影响,其活性序列如下:PcM(pip)_2>PcM(Py)_2>PcM(γ-picol)_2≈PcM(N-MeIm)_2.     

双核钴锰酞菁对SOCl2还原反应的电催化性能

为了确定双核金属酞菁化合物对亚硫酰氯还原反应是否具有比单核金属酞菁更强的电催化性能, 通过循环伏安测试方法, 用酞菁钴和酞菁铁作为对比, 研究了双核钴锰酞菁在1.5 mol·L-1 LiAlCl4/SOCl2电解液中的电催化行为, 并计算出动力学参数, 由此来评估具有平面结构的双核金属酞菁化合物对亚硫酰氯还原的催化活性的影响. 通过比较循环伏安曲线发现, 与单核酞菁钴(II)和酞菁铁(II)相比, 双核钴锰酞菁对SOCl2还原反应具有更好的催化活性, 能提高SOCl2还原反应的交换速率常数和SOCl2在玻碳电极上的扩散系数, 从而提高SOCl2还原电位和电流.通过ER14250型实体电池10 mA放电性能测试验证表明, 与单核酞菁钴和酞菁铁催化剂的电池相比, 双核钴锰酞菁在低温(-30 ℃)下可提高放电中点电压0.3 V, 在常温(25 ℃)下可以提高放电容量约100 mAh, 催化效果比单核酞菁钴和酞菁铁显著.     

CoPc(COOH)8-SA/mCS双极膜的制备及表征

分别用Fe3+离子和戊二醛作为交联剂对海藻酸钠(SA)阳膜层和壳聚糖(CS)阴膜层进行改性, 制备了八羧基钴酞菁-海藻酸钠/改性壳聚糖(CoPc(COOH)8-SA/mCS)双极膜(BPM). 在海藻酸钠阳膜层中添加八羧基钴酞菁以提高阳膜的离子交换容量, 促进中间层水的解离. 用傅立叶红外(FT-IR)光谱、扫描电镜(SEM)等方法对制备的双极膜进行了表征. 实验结果表明, 经八羧基钴酞菁改性后, 阳离子交换膜层的离子交换容量、H+离子透过率均获得提高. 与Fe3+离子改性或二茂铁离子改性的mSA/mCS双极膜相比, CoPc(COOH)8-SA/mCS双极膜的交流阻抗、电阻压降(IR降)和溶胀度降低. 当电流密度高达105 mA·cm-2时, CoPc(COOH)8-SA/mCS双极膜的IR降仅为0.7 V.     

四取代羧基酞菁锌与白蛋白共价结合物的制备与光谱性质

通过成酰胺键的方式制备了一系列含羧基酞菁和白蛋白(牛血清白蛋白(BSA),人血清白蛋白(HSA))之间的共价结合物,所涉及到的酞菁分别是α-四(4-羧基苯氧基)酞菁锌(1)和α-四[4-(2-羧基乙基)苯氧基]酞菁锌(3),以及它们相应的β位四取代酞菁锌(化合物2和4).比较了游离酞菁以及它们的白蛋白结合物在磷酸盐缓冲溶液(PBS)中的光谱性质.结果表明,当酞菁被共价固定于白蛋白大分子上之后,展现出比游离酞菁更明显的单体特征吸收,而且结合物中的酞菁光谱特征不受体系pH值变化的影响.羧基在酞菁环上的取代位置,对酞菁与白蛋白结合前后的光谱转变幅度有影响,α位取代比β位取代更有利于光谱的变化.化合物1和3的白蛋白共价结合物在PBS溶液中甚至呈现出单体形式为主的光谱特征,Q带最大吸收波长分别位于697和706nm附近.     

囊泡双层膜中4,4'4'4'-四(正丙氧基羰基)酞菁钴(Ⅱ)催化分子氧氧化巯基苯的反应

金属酞菁具有与卟啉及维生素 B12 辅酶相似的结构 ,是具有潜力的金属酶模型 ,以金属酞菁为活性中心的模拟酶的相关研究 ,对酶促反应和仿酶催化功能的应用具有重要意义[1] .Shirai等[2 ] 指出水溶性羧基铁 ( )和钴 ( )酞菁衍生物在水溶液中的催化反应具有酶促反应的动力学特征 .白妮等 [3] 也发现 ,固载于 MCM- 41介孔分子筛孔内的脂溶性金属酞菁在水溶液中具有类似的催化功能 .但目前还没有见到在疏水微环境或有机溶剂中金属酞菁衍生物催化功能的相关报道 .生物膜和酶蛋白提供的疏水微环境对许多酶促反应起着关键作用 [4 ] ,Murakami等…     

囊泡双层膜中4，4′4″4彬′′′-四（正丙氧基羰基）酞菁钴（Ⅱ）催化分子氧氧化巯基苯的反应

金属酞菁具有与卟啉及维生素B12辅酶相似的结构，是具有潜力的金属酶模型，以金属酞菁为活性中心的模拟酶的相关研究，对酶促反应和仿酶催化功能的应用具有重要意义，Shirai等指出水溶性羧基铁(Ⅲ)和钴(Ⅱ)酞菁衍生物在水溶液中的催化反应具有酶促反应的动力学特征，白妮等也发现，     

新型四羧基铝酞菁-二氧化硅荧光纳米粒子的合成及在酸度测定中的应用

首次制备出红区荧光染料四羧基铝酞菁掺杂的二氧化硅纳米粒子,并对其进行了表征。将环己烷、正己醇和表面活性剂Triton X-100按一定体积比(12.3∶1.04∶1)混合均匀,形成清澈透明的溶液;将适量的四羧基铝酞菁溶解到浓氨水中,加入到上述混合溶液中,形成反向胶束。搅拌10 m in后加入一定量的四乙氧基硅烷,加快搅拌速度,促使四乙氧基硅烷进入反相胶束中的“纳米水池”,在碱性条件下,四乙氧基硅烷水解形成二氧化硅纳米粒子。采用该方法制备的核壳荧光纳米颗粒荧光稳定性强,生物相容性高,抗干扰能力强。将一定量四羧基铝酞菁掺杂的二氧化硅纳米粒子溶于水溶液中,随溶液pH值的增加,荧光强度增强,并在pH 5.02~11.98的范围内,荧光强度与溶液酸度有良好的线性关系。该法已成功地用于自来水和模拟生物体系中pH的测定。预期该技术有望用于细胞内H 的实时监测。     

酞菁铁催化烯烃自由基膦叠氮化反应:利用叠氮快速转移合成膦叠氮的温和方法

含氮和磷原子的化合物是生命系统中不可缺少的组成部分,由于其独特的化学、生物和物理性质,已被广泛应用于农业化学、材料科学和制药学.如果一个有机化合物同时含有氮和磷原子,它可能因为胺和膦/磷酸盐基团的协同作用而具有额外的功能.2015年赵玉芬院士和唐果教授报道了一例自由基叠氮膦酰化的例子,该反应虽然有效,但因需使用化学剂量的氧化性自由基引发剂Mn(OAc)3·2H2O,因此,有必要发展一种更环保经济的方法.本文报道了铁催化烯烃的分子间自由基膦叠氮化反应.该方法使用了微量的催化剂,通过自由基接力与叠氮基团转移实现分子间自由基膦叠氮化反应.实验先进行条件筛选,考察了催化剂类型、催化剂用量、氧化剂类型、溶剂和温度对反应的影响,确定以酞菁铁为催化剂,叔丁基过氧化氢(TBHP)为引发剂,乙腈为溶剂,苯乙烯、叠氮基三甲基硅烷、二苯基膦酰为模板反应底物为最佳条件,实现了二苯基膦酰对烯烃的自由基膦酰基叠氮化反应.在最优条件下进行底物拓展,制备得到27种膦叠氮化合物,产率为23％～88％.以制得的膦叠氮产物为起始原料,通过叠氮还原和Click反应制备得到三种衍生物,产率为82％～97％,可作为药物合成中间体进行下一步研究.本文还进行了机理实验和理论计算.在自由基钟实验和自由基捕获实验中,通过两种不同速率的自由基开环反应与自由基捕获反应证实了反应的自由基路径.质谱检测到酞菁铁羟基(PcFeⅢOH)和酞菁铁叠氮(PcFeⅢN3)的存在.采用密度泛函理论计算了不同自旋态下的酞菁铁(PcFe),以确定可能的催化剂种类,并计算出三重态3pcFe最稳定.从三重态3pcFe开始计算铁催化叔丁基过氧化氢的单电子转移,并计算了从叔丁氧基自由基开始的自由基接力,证实了膦酰苄基自由基的形成是最有利的途径;研究结果发现膦酰苄基自由基能与4pcFe(N3)反应,发生叠氮基团转移生成目标产物.在叠氮基团转移计算中,考察了四种合理的途径,分别是苄基在三重态或五重态势能面接近叠氮基团的内部或端位氮原子(Ni和Nt).结果 表明,叠氮基团从叠氮基酞菁铁(Ⅲ)物种(PcFeⅢN3)转移到苄基自由基的活化能(4.8 kcal/mol)极低.据此催化循环机理可能为:酞菁铁首先与叔丁基过氧化氢发生单电子转移形成酞菁铁羟基中间体及叔丁氧自由基;然后,二苯基膦酰的氢原子被叔丁氧自由基攫取生成二苯基膦酰自由基,并加成至苯乙烯形成苄基自由基.同时,酞菁铁羟基中间体与HN3进行配体交换形成酞菁铁叠氮中间体,最后与苄基自由基进行叠氮基团转移生成产物,并重新生成酞菁铁(Ⅱ).本文证实了铁催化叠氮化反应的自由基基团转移机理(外球机理),因为很难想象如何在酞菁铁的同侧同时加成叠氮与苄基基团,通过生成高价铁物种(PcFe-N3·)的内球机理得到产物.该工作将有助于启发更多的金属催化机理研究.     

PREPARATION AND CATALYTIC ACTIVITY OF BIOACTIVE FIBERS

Two kinds of water-soluble metallophthalocyanines, binuclear cobalt phthalocyanine （Co2Pc2） and binuclear ferric phthalocyanine （Fe2Pc2）, were synthesized through phenylanhydride-urea route and characterized by elemental analysis and FT-IR spectra. Binuclear metallophthalocyanine derivatives （Mt2Pc2） were immobilized on silk fibers and modified viscose fibers to construct bioactive fibers of mimic enzyme. Mt2Pc2 was used as the active center of bioactive fibers, viscose and silk fibers as the microenvironments. The catalytic oxidation ability of bioactive fibers on the malodors of methanthiol and hydrogen sulfide was investigated at room temperature. The experimental results indicated that the catalytic activity of such bioactive fibers was closely correlative to the types ofbioactive fibers and substrates.     

STUDY ON THE CATALYTIC ABILITY OF BIOACTIVE FIBERS

1. INTRODUCTIONEnzyme as a biologic catalyst plays an important role in all kinds of chemical reactions inside living creatures. Comparing to chemical catalysts, the natural enzyme has many advantages such as high speed, specificity, sensitivity and mild …     

STUDY ON THE CATALYTIC ABILITY OF BIOACTIVE FIBERS

Two kinds of water-soluble metallophthalocyanines (Mt2Pc2), binuclear cobalt phthalocyanine (Co2Pc2) and binuclear ferric phthalocyanine (Fe2Pc2), were supported on silk fibers and modified viscose fibers to construct bioactive fibers of mimic enzyme, Mt2Pc2 used as the active center of bioactive fibers, viscose and silk fibers as the microenvironments. The catalytic oxidation ability of bioactive fibers on the malodors of methanthiol and hydrogen sulfide was investigated at room temperature. The experimental results demonstrated that the catalytic activity of such bioactive fibers was tightly correlative to the types of bioactive fibers and substrates.     

Ab initio study of oxygen atom transfer from hydrogen peroxide to trimethylamine

Unlike what has been theoretically proposed for ammonia oxidation with hydrogen peroxide, trimethylamine oxidation occurs with a concerted mechanism, which is favored even when an explicit water molecule is added or continuum solvent (water) is simulated.     

A study on Zn-based catal-sorbents for the simultaneous removal of hydrogen sulfide and ammonia at high temperature

To simultaneously remove hydrogen sulfide and ammonia from hot coal gases, the ammonia decomposition abilities of various metal oxide catalysts were tested in the absence/presence of hydrogen sulfide, at 650 °C. Cobalt oxide, molybdenum oxide, and nickel oxide have high ammonia decomposition abilities (>95%) in the absence of hydrogen sulfide, but such abilities rapidly decreased during the reaction in the presence of hydrogen sulfide. To improve the simultaneous removal abilities of metal oxides, Zn-based catal sorbents were prepared via impregnation with various metals, such as cobalt, nickel, and molybdenum, on zinc oxide. The CZ-30 (promoted with 30 wt% cobalt oxide on zinc oxide) and NZ-30 (promoted with 30 wt% nickel oxide on zinc oxide) catal sorbents showed excellent sulfur removal capacities, which, calculated until the breakthrough point, were 0.35 and 0.39 g S/g catal sorbent, respectively, while MZ-30 promoted with molybdenum showed a low sulfur removal capacity of 0.08 g S/g catal sorbent. The ammonia decomposition ability of CZ-30, however, increased more than 18 times compared with Co₃O₄, whose ammonia decomposition ability was more than 95% until 465 min, even though the ammonia decomposition ability of NZ-30 sharply decreased after 30 min. The CZ catal sorbent is a good candidate for the simultaneous removal of ammonia and hydrogen sulfide.     

Creation of active sites by impregnation of carbon fibers: application to the fixation of hydrogen sulfide

Activated carbon fibers, which exhibit high specific area and numerous active surface sites, constitute very powerful adsorbents and are widely used in filtration to eliminate pollutants from liquid or gaseous effluents. The fibers studied in this work are devoted to the filtration of gaseous effluent containing very small amounts (few vpm) of hydrogen sulfide. Preliminary experiments evidenced that these fibers weakly adsorb hydrogen sulfide. To improve their fixation capacity toward H(2)S the activated fibers are impregnated in an aqueous solution of potassium hydroxide. The impregnation treatment usually takes place before activation but in this work it occurs at room temperature after activation of the fibers. A further thermal treatment is performed to increase the efficiency of the system. The overall treatment leads to the creation of basic sites showing a great activity for H(2)S gas in the presence of water vapor. The mechanism has been established by a series of characterizations before, during, and after the different operation units. The KOH deposited after impregnation is carbonated into KHCO(3) at room temperature and then decomposed into K(2)CO(3) during the thermal treatment. K(2)CO(3) and H(2)S dissolve in a liquid aqueous solution formed on the fiber surface. Then carbonate ions and H(2)S molecules react together almost completely to yield HS(-) species. As a consequence the sorption capacities of hydrogen sulfide on the impregnated fibers are much higher, even for small hydrogen sulfide volume fractions.     

Extraction of Mercaptans from Light Hydrocarbon Mixtures with Aqueous Ammonia

Results of laboratory studies of the extraction of light mercaptans (methyl, ethyl, and propyl mercaptans) from hydrocarbons mixtures with a 25% aqueous solution of ammonia (caustic ammonia) are presented and discussed. It is shown that aqueous ammonia can in principle be used for controlled demercaptanization of light hydrocarbon fractions and liquefied hydrocarbon gases containing hydrogen sulfide and lower mercaptans. The advantage of this demercaptanization method over the conventional processes of alkali treatment is that there is no stage of oxidative catalytic regeneration of a spent alkali and there are no its highly toxic wastes, sulfurousalkaline waste waters. The regeneration of a spent (saturated with sulfurous compounds) aqueous ammonia can be comparatively easily performed by its heating (boiling), which leads to a hydrolytic decomposition of ammonium sulfides and mercaptides to release their constituent gases: hydrogen sulfide, mercaptans, and ammonia. Ammonia is recycled into the process as freshly prepared (regenerated) caustic ammonia.

     

o-Quinone methide as alkylating agent of nitrogen, oxygen, and sulfur nucleophiles. The role of H-bonding and solvent effects on the reactivity through a DFT computational study

The reactivity of the alkylating agent o-quinone methide (o-QM) toward NH(3), H(2)O, and H(2)S, prototypes of nitrogen-, oxygen-, and sulfur-centered nucleophiles, has been studied by quantum chemical methods in the frame of DF theory (B3LYP) in reactions modeling its reactivity in water with biological nucleophiles. The computational analysis explores the reaction of NH(3), H(2)O, and H(2)S with o-QM, both free and H-bonded to a discrete water molecule, with the aim to rationalize the specific and general effect of the solvent on o-QM reactivity. Optimizations of stationary points were done at the B3LYP level using several basis sets [6-31G(d), 6-311+G(d,p), adding d and f functions to the S atom, 6-311+G(d,p),S(2df), and AUG-cc-pVTZ]. The activation energies calculated for the addition reactions were found to be reduced by the assistance of a water molecule, which makes easier the proton-transfer process in these alkylation reactions by at least 12.9, 10.5, and 6.0 kcal mol(-1) [at the B3LYP/AUG-cc-pVTZ//B3LYP/6-311+G(d,p) level], for ammonia, water, and hydrogen sulfide, respectively. A proper comparison of an uncatalyzed with a water-catalyzed reaction mechanism has been made on the basis of activation Gibbs free energies. In gas-phase alkylation of ammonia and water by o-QM, reactions assisted by an additional water molecule H-bonded to o-QM (water-catalyzed mechanism) are favored over their uncatalyzed counterparts by 5.6 and 4.0 kcal mol(-1) [at the B3LYP/6-311+G(d,p) level], respectively. In contrast, the hydrogen sulfide alkylation reaction in the gas phase shows a slight preference for a direct alkylation without water assistance, even though the free energy difference (DeltaDeltaG(#)) between the two reaction mechanisms is very small (by 1.0 kcal mol(-1) at the B3LYP/6-311+G(d,p),S(2df) level of theory). The bulk solvent effect, evaluated by the C-PCM model, significantly modifies the relative importance of the uncatalyzed and water-assisted alkylation mechanism by o-QM in comparison to the case in the gas phase. Unexpectedly, the uncatalyzed mechanism becomes highly favored over the catalyzed one in the alkylation reaction of ammonia (by 7.0 kcal mol(-1)) and hydrogen sulfide (by 4.0 kcal mol(-1)). In contrast, activation induced by water complexation still plays an important role in the o-QM hydration reaction in water as solvent.     

Hydrocarbons as proton donors in C–H⋯N and C–H⋯S hydrogen bonds

C–H?N and C–H?S hydrogen bonds were analyzed in complexes where acetylene, ethylene, methane and their derivatives are proton donors while ammonia and hydrogen sulfide are proton acceptors. Ab initio calculations were performed to analyze those interactions; MP2 method was applied and the following basis sets were used: 6-311++G(d,p), aug-cc-pVDZ and aug-cc-pVTZ. The results showed that hydrogen bonds for complexes with ammonia are systematically stronger than such interactions in complexes with hydrogen sulfide. If the fluorine substituted hydrocarbons are considered then F-substituents enhance the strength of hydrogen bonding. For a few complexes, mainly those where carbon atom in proton donating C–H bond possesses sp³ hybridization, the blue-shifting hydrogen bonds were detected. Additionally, Quantum Theory of ‘Atoms in Molecules’ and Natural Bond Orbitals method were applied to analyze H-bond interactions.     

Enhanced removal of acid red 1 with large amounts of dyeing auxiliaries: the pivotal role of cellulose support

As an almost inexhaustible material with unique and outstanding properties, cellulose presents promising potential in the practical issues. In this study, the cellulose fibers-supported cobalt tetra(2,4-dichloro-1,3,5-triazine)aminophthalocyanine(denoted as Co-TDTAPc-F) catalyst and H₂O₂ system was introduced for removing organic dyes from aqueous solution with large amounts of dyeing auxiliaries. The model dye (acid red 1, AR1) in a relatively low concentration was removed efficiently with a hydroxyl radical (·OH)-involved mechanism. Due to the inherently excellent performance of cellulose fibers (CFs) such as the controllable surface potential and unique swelling ability in aqueous solution, the catalytic oxidation of AR1 was evidently enhanced in the presence of typical dyeing additives (NaCl and urea). Furthermore, CFs have significantly reduced the alcohol inhibition in traditional ·OH-involved reactions by forming hydrogen bonds with hydroxyl group-containing compounds, just like isopropanol. Consequently, such innately wonderful properties of cellulose carriers allowed Co-TDTAPc-F to be a promising catalyst for removing highly hazardous target pollutants in actual wastewater with large amounts of organic and inorganic compounds. The finding serves as an example of well used excellent performance of cellulose support for better reactions, further leading to a comprehensive understanding and application of cellulose.