Velocity distributions in Taylor vortex flow with imposed laminar axial flow and isothermal surface heat transfer

Fully-developed flow in a concentric annulus formed by a stationary outer cylinder, which may be heated isothermally, and a rotatable inner cylinder has been studied experimentally by means of hot-wire anemometry techniques. Velocity profiles for the axial, tangential, and radial directions of flow have been obtained for adiabatic conditions and for wide and narrow annular gaps.It has been shown that the onset of Taylor vortex flow has a pronounced effect on the velocity profiles for all three directions. However, while the profiles for the axial and tangential directions are explicable, those for the radial direction are not so, at present. Also, it was found that heat transfer through the outer annular surface had a greater effect on the radial velocity profile than on the axial or tangential, but in the narrow gap case only.     

An experimental study of diabatic spiral vortex flow

In spiral vortex flow, between concentric cylinders with the inner cylinder rotating and the outer stationary, the addition of a thermal gradient across the gap is a known complicating factor. The present diabatic study for narrow and wide gaps (radius ratios N=0.955 and N=0.8), with a heated outer and adiabatic inner cylinder, was undertaken to investigate this problem. The heat transfer characteristics and the modes of transition have been investigated together with the relationship between them. Using standard on-line digital computer techniques, the onset of vortex flow and its higher transitions have been shown to cause a sharp increase in Nusselt number. At higher Taylor numbers, of the order of 10⁶, a marked change in the Nusselt number occurs with the onset of the transition to periodic turbulent vortex flow. Outer wall heating is seen to affect the modes of transition. Diabatic critical Taylor numbers are much higher than those for adiabatic conditions and are found to depend on the close approach of the vortices to the outer wall     

不同参数下环形通道内湍流旋流流动的模拟

应用一种合理考虑湍流一旋流相互作用及湍流脉动各向异性的新的代数ＲｅｙｎｏｌｄＳ应力模型,对环形通道内的湍流旋流流动进行了数值模拟．研究了旋流数、进口轴向速度和内外半径比等参数对环形通道内湍流旋流流动的影响,以及由此产生的流场变化对强化环形通道内传热的作用．     

Free-convection flow through an annular porous medium

This study addresses the Brinkman-extended Darcy model (Brinkman flow) of a laminar free-convective flow in an annular porous region. Closed form expressions for Velocity field, Temperature field, Skin-friction and Mass flow rate are given, under a thermal boundary condition of mixed kind at the outer surface of the inner cylinder while the inner surface of the outer cylinder is isothermal. The governing independent parameters are identified to be Darcy number (Da) and ratio of outer to inner radii (R). It is hoped that the study of such flows gives limiting conditions for developing flows and provides an analytical check on numerical solutions for more complex problems dealing with non-Darcian free-convection flow in an annular region.     

An asymmetrical periodic vortical structures and appearance of the self induced pressure gradient in the modified Taylor flow

An incompressible liquid flow in the gap between two coaxial cylinders, such that the inner rotating (wavy) cylinder has a periodically varying radius along the axial direction while the outer stationary cylinder has a constant radius, is studied experimentally and theoretically. Basic attention is focused on the symmetry-breaking phenomenon of the vortex flow arising from the rotation of the inner wavy cylinder. It is found that the symmetry-breaking phenomenon of the vortical flow structures in this geometry is accompanied by the occurrence of a self-induced axial pressure gradient. A theoretical formulation of the problem of periodic vortical flow prevailing in such a geometry having large axial length is presented. The comparison between the computed and the experimental results is presented and the underlying phenomena are discussed.     

Solution of three-dimensional natural convection about a vertical square rod in a cylindrical enclosure

The problem of three-dimensional laminar natural convection in a vertical enclosure with an inner square rod is treated by a numerical method in boundary-fitted co-ordinates. The inner and outer cylinders are heated and cooled, respectively, to maintain different constant surface temperatures. The horizontal enclosure surfaces are maintained at adiabatic conditions. The Prandtl number is that of air, 0·703, and the Rayleigh numbers span the conduction, transition and boundary layer regimes of flow. The radius ratio is 1, and the aspect ratio (cylinder length divided by maximum annular gap) is 1. The results of the study provide data useful in the design and performance assessment of nuclear reactor spent fuel shipping casks.     

An investigation of adiabatic spiral vortex flow in wide annular gaps by visualisation and digital analysis

This paper, the third in a series describing experimental investigations into spiral vortex flow, presents visual evidence illustrating adiabatic transition modes in a wide gap of radius ratio 0.848. Also, power spectra, relating to velocity fluctuations, are found to be comparable for two working fluids, oil and air. Good agreement has been found between these results and those published by the authors in which diabatic transition modes were related to the heat transfer characteristics of the flow at various axial Reynolds numbers     

MODELLING AND CALCULATION OF THE TURBULENT BOUNDARY LAYER ON A ROTATING CYLINDER SURFACE WITH STRONG SUCTION 1)

提出了湍流边界层的一种简单、快速计算方法, 用以求解强吸气作用下旋转圆筒表面边界层流动. 首先, 理论分析了同心圆筒间的旋转流体运动, 外筒静止、内筒旋转且为多孔吸气条件. 强吸气情况下旋转流动主要表现为内筒壁面附近的边界层流动, 基于这一事实得到了周向速度分布的解析表达式. 其次, 通过引入新参数扩展Cebeci-Smith代数湍流模型, 使其能考虑流线曲率、壁面吸气、低Reynolds数效应等因素. 针对这些因素的综合影响, 采用解析修正和经验参数对模型进行调整. 同时, 基于Reynolds应力湍流模型的仿真结果, 校准代数湍流模型中的经验参数. 最后, 给出基于广义Cebeci-Smith湍流模型的旋转壁面边界层流动的迭代算法, 该算法适用于需要特殊迭代过程的轴向及周向流动均匀情况. 计算了不同旋转速度和吸气强度组合工况下的边界层流动, 其周向速度和湍流强度分布与基于Reynolds应力湍流模型的计算结果非常接近. 并且表明, 当Reynolds应力湍流模型数值模拟预测内筒边界层为稳定层流时, 该方法也再现了相同初始条件下的层流边界层.     

Steady thermocapillary-buoyant convection in a shallow annular pool. Part 1: Single layer fluid

This paper examines the steady thermocapillarybuoyant convection in a shallow annular pool subjected to a radial temperature gradient. A matched asymptotic theory is used to obtain the asymptotic solutions of the flow and thermal fields in the case of small aspect ratios,which is defined as the ratio of the layer thickness to the gap width. The flow domain is divided into the core region away from the cylinder walls and two end regions near each cylinder wall. Asymptotic solutions are obtained in the core region by solving the core and end flows separately and then joining them through matched asymptotic expansions. For the system of silicon melt,the asymptotic solutions are compared with the results of numerical simulations. It is found that the two kinds of solutions have a good agreement in the core region for a small aspect ratio. With the increase of aspect ratio,the applicability of the present asymptotic solutions decreases gradually.     

The experimental determination of velocity distribution in annular flow

In the study of the flow of a fluid through an annular gap, the outer surface of which is stationary while the inner surface may be rotated, it is necessary to be able to accurately determine the velocity profiles obtaining in the axial, tangential, and radial directions of flow.

A method is described for this purpose employing hot-wire anemometry techniques and typical profiles are presented for each of the above flow directions. In the case of pure axial flow, a comparison is made between experimental and theoretical results, showing a close correspondence.     

Circular Couette flow with pressure-driven axial flow and a porous inner cylinder

In a rotating filter separator a suspension is introduced at one end of the annulus between a rotating porous inner cylinder and a fixed impermeable outer cylinder. The filtrate is removed through the inner cylinder and the concentrate is removed from the opposite end of the annulus from which the suspension entered. The flow in a rotating filter separator is circular Couette flow with a pressure-driven axial flow and a suction boundary condition at the inner cylinder. Flow visualization was used to determine the effect of the Taylor number, axial Reynolds number, and radial Reynolds number on the types of flows present in the annulus. A rich variety of secondary vortical flows appear, depending upon the flow parameters. The radial inflow at the inner cylinder delays the appearance of supercritical circular Couette flow and prevents the appearance of certain flow regimes that have a helical vortex structure. Nevertheless, the average azimuthal velocity measured using laser Doppler velocimetry indicates that the velocity profile is nearly the same for all supercritical flow regimes.This work was supported by a grant from The Whitaker Foundation     

强吸气旋转圆筒壁面湍流边界层建模及计算

提出了湍流边界层的一种简单、快速计算方法, 用以求解强吸气作用下旋转圆筒表面边界层流动. 首先, 理论分析了同心圆筒间的旋转流体运动, 外筒静止、内筒旋转且为多孔吸气条件. 强吸气情况下旋转流动主要表现为内筒壁面附近的边界层流动, 基于这一事实得到了周向速度分布的解析表达式. 其次, 通过引入新参数扩展Cebeci-Smith代数湍流模型, 使其能考虑流线曲率、壁面吸气、低Reynolds数效应等因素. 针对这些因素的综合影响, 采用解析修正和经验参数对模型进行调整. 同时, 基于Reynolds应力湍流模型的仿真结果, 校准代数湍流模型中的经验参数. 最后, 给出基于广义Cebeci-Smith湍流模型的旋转壁面边界层流动的迭代算法, 该算法适用于需要特殊迭代过程的轴向及周向流动均匀情况. 计算了不同旋转速度和吸气强度组合工况下的边界层流动, 其周向速度和湍流强度分布与基于Reynolds应力湍流模型的计算结果非常接近. 并且表明, 当Reynolds应力湍流模型数值模拟预测内筒边界层为稳定层流时, 该方法也再现了相同初始条件下的层流边界层.      

Numerical simulation of Taylor Couette flow of Bingham fluids

The Bingham fluid flow between two concentric cylinders is studied using numerical simulation. The cylinders are assumed to rotate independently, and with an imposed axial sliding. The flow field is decomposed with linearity arguments of the base circular Couette shear flow and corresponding deviation field. The numerical methods are based on the expression of the deviation field in terms of complete sets of orthogonal functions and Chebyshev series. The Galerkin projection method is used with the pressure term being eliminated. The Adams Bashforth scheme is adopted for time marching. The results show that the vortices are squeezed toward the inner cylinder due to the effect of yield stress. When the outer cylinder is held stationary, the yield stress plays a role in weakening the vortex flow. However, for the co-rotation situation, the vortex flow is initially strengthened with an increase of yield stress, and then weakened as the yield stress is raised large enough. The annular unyielded regions emerge and stick to the outer cylinder. In case of Taylor Couette flow with an imposed axial sliding, a spiral vortex flow is visible with spiral unyielded region being obtained.     

环形浅池内硅熔体中的热流体波

为了了解工业Czochralski炉内硅熔体表面轮型的基本特征,对环形浅池内硅熔体的热毛细-浮力对流进行了三维数值模拟,硅熔池内径为15 mm,外径为50 mm,深度为3 mm,熔池外壁被加热,内壁被冷却,底部固壁和顶部自由表面均绝热或者允许一个垂直方向的传热。模拟结果表明,当径向温差较小时,熔池内会产生稳定的单胞热毛细-浮力流动,随着温差的增大,流动将转变为三维振荡流动,在熔体自由表面会出现沿周向运动的轮型,小的垂直方向的热流密度(3W/cm2)对这种振荡流动没有大的影响。同时,讨论了流动和温度波动的特征,并确定了振荡流动的临界条件。     

环形截面螺旋管道内二次流动特性的研究

从曲线柱坐标系下的N-S方程出发,以曲率和挠率为小参数,采用摄动法求解了环形截面螺旋管道内的黏性流动,给出了完全二阶摄动解,结果表明：当挠率为零时,二次流表现为上下对称的四个涡;当挠率不为零,涡的对称性遭到破坏,二次涡的强度和个数受De数和环形截面内外径之比δ的影响,轴向速度最大值在De数较小时靠近管道的内侧,随着De数的增加,其最大值向外侧移动。     

双柱单锥型液-液旋流管内流场的激光诊断

应用激光测速仪，对一种双柱单锥型液 液旋流管内的流动结构，进行了全场范围内的多工况流动诊断研究．揭示出其切向速度由内旋流区和外旋流区构成，其中内旋流区中的速度分布符合准强制涡关系，外旋流区中的速度分布符合准自由涡关系；轴向速度由上行流动区和下行流动区构成，两者之间在直管段以零速点作分界，在锥体段则以零速区作过渡并伴随有一定的回流出现，且该过渡区或回流区的大小随锥体截面的收缩而减小，直到进入直管段后消失；各湍流量的分布以管芯处最大向外逐渐减小，沿轴向是直管段中的湍流度大于锥体段中的湍流度，而且湍流度在旋流管内具有各向异性的特性．     

On the orbital motion of a rotating inner cylinder in annular flow

In this paper, numerical calculations have been performed to analyse the influence of the orbital motion of an inner cylinder on annular flow and the forces exerted by the fluid on the inner cylinder when it is rotating eccentrically. The flow considered is fully developed laminar flow driven by axial pressure gradient. It is shown that the drag of the annular flow decreases initially and then increases with the enhancement of orbital motion, when it has the same direction as the inner cylinder rotation. If the eccentricity and rotation speed of the inner cylinder keep unchanged (with respect to the absolute frame of reference), and the orbital motion is strong enough that the azimuthal component (with respect to the orbit of the orbital motion) of the flow‐induced force on the inner cylinder goes to zero, the flow drag nearly reaches its minimum value. When only an external torque is imposed to drive the eccentric rotation of the inner cylinder, orbital motion may occur and, in general, has the same direction as the inner cylinder rotation. Under this condition, whether the inner cylinder can have a steady motion state with force equilibrium, and even what type of motion state it can have, is related to the linear density of the inner cylinder. Copyright © 2006 John Wiley & Sons, Ltd.     

Natural convection in vertical concentric annuli under a radial magnetic field

Exact solutions for fully developed natural convection in open-ended vertical concentric annuli under a radial magnetic field are presented. Expressions for velocity field, temperature field, mass flow rate and skin-friction are given, under more general thermal boundary conditions. It is observed that both velocity as well as temperature of the fluid is more in case of isothermal condition compared with constant heat flux case when gap between cylinders is less or equal to radius of inner cylinder while reverse phenomena occur when the gap between cylinders is greater than radius of inner cylinder.     

An investigation of adiabatic spiral vortex flow by means of cross-wire probes

Flow transitions occurring with increase in the Taylor number in an annular gap of radius ratio 0.8, having an imposed axial flow of air of Reynolds number 500 have been studies using the output from a cross-wire probe in a complex digital analysis. Cross and phase spectra, together with auto and cross correlograms, are presented for four Taylor numbers from 10 620 to 12.2 × 10⁶, covering the onset of vortex flow, chaotic flow and turbulent vortex flow. As the Taylor number increases, there is little alteration in the spiral vortex flow in the axial and tangential directions, which oscillates in phase in these two directions. The tangential velocity gradient was seen to become increasingly dominant, with increase in the Taylor number     

Determination of the thermal stress wave propagation in orthotropic hollow cylinder based on classical theory of thermoelasticity

The thermoelasticity problem in a thick-walled orthotropic hollow cylinder is solved analytically using finite Hankel transform and Laplace transform. Time-dependent thermal and mechanical boundary conditions are applied on the inner and the outer surfaces of the cylinder. For solving the energy equation, the temperature itself is considered as boundary condition to be applied on both the inner and the outer surfaces of the orthotropic cylinder. Two different cases are assumed for solving the equation of motion: traction–traction problem (tractions are prescribed on both the inner and the outer surfaces) and traction–displacement (traction is prescribed on the inner surface and displacement is prescribed on the outer surface of the hollow orthotropic cylinder). Due to considering uncoupled theory, after obtaining temperature distribution, the dynamical structural problem is solved and closed-form relations are derived for radial displacement, radial and hoop stress. As a case study, exponentially decaying temperature with respect to time is prescribed on the inner surface of the cylinder and the temperature of the outer surface is considered to be zero. Owing to solving dynamical problem, the stress wave propagation and its reflections were observed after plotting the results in both cases.