No-Glycerol rapid heterogeneous biodiesel production on K<Subscript>2</Subscript>CO<Subscript>3</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst by coupling process

Biodiesel containing almost no glycerol has been produced by coupling reaction carried out over K₂CO₃ supported by calcium oxide as solid base catalysts. The solid base catalysts synthesized by wet impregnation exhibit an exceedingly high activity in biodiesel production. It was found that the reaction time required for the highest yield of biodiesel, 99.2%, can be shortened to 30 min over K₂CO₃/Al₂O₃ under the optimum reaction conditions: 8: 1: 1 molar ratio of methanol/DMC/oil, 30 wt % K₂CO₃/Al₂O₃ catalyst, and 65°C reaction temperature. Solid basic catalysts examined in the study were characterized by BET surface area, XRD, CO₂-TPD, and SEM techniques. The strong interaction between K₂CO₃ and the support yields a new basic active site, which can be probably responsible for the high activity of K₂CO₃/Al₂O₃.     

Production of 5‐Hydroxymethylfurfural from Fructose in Ionic Liquid Efficiently Catalyzed by Cr(III)‐Al2O3 Catalyst

A series of metal‐Al₂O₃ catalysts were prepared simply by the conventional impregnation with Al₂O₃ and metal chlorides, which were applied to the dehydration of fructose to 5‐hydroxymethylfurfural (HMF). An agreeable HMF yield of 93.1% was achieved from fructose at mild conditions (100°C and 40 min) when employing Cr(III)‐Al₂O₃ as catalyst in 1‐butyl‐3‐methylimidazolium chloride ([Bmim]Cl). The Cr(III)‐Al₂O₃ catalyst was characterized via XRD, DRS and Raman spectra and the results clarified the interaction between the Cr(III) and the alumina support. Meanwhile, the reaction solvents ([Bmim]Cl) collected after 1^st reaction run and 5^th reaction run were analyzed by ICP‐OES and LC‐ITMS and the results confirmed that no Cr(III) ion was dropped off from the alumina support during the fructose dehydration. Notably, Cr(III)‐Al₂O₃ catalyst had an excellent catalytic performance for glucose and sucrose and the HMF yields were reached to 73.7% and 84.1% at 120°C for 60 min, respectively. Furthermore, the system of Cr(III)‐Al₂O₃ and [Bmim]Cl exhibited a constant stability and activity at 100°C for 40 min and a favorable HMF yield was maintained after ten recycles.     

Physicochemical and Reactivity Studies on Polystyrene‐Cu/Al2O3 Catalysts: An Attempt to Control Copper Dispersion

The influence of coating of 5.0 (w/w%) Cu/γ‐Al₂O₃ catalyst by different ratios of polystyrene on the physicochemical and textural properties was studied. The physicochemical and textural properties of polystyrene‐`Cu/γ‐Al₂O₃ catalysts were investigated by N₂ adsorption, O₂ chemisorption, FTIR, XRD, TEM, and SEM. In addition, the kinetics of H₂O₂ decomposition as a model redox reaction over polymer coated and uncoated catalysts was investigated. The highest activity was achieved by 0.06 wt% polystyrene‐5.0Cu/γ‐Al₂O₃ catalyst. The parent 5.0Cu/γ‐Al₂O₃ catalyst showed auto‐catalytic first order mechanism, which was subjected to a pronounced modification to a simple first order one upon coating by polystyrene. This modification in the mechanism was accompanied with an increase in the apparent activation energy of the reaction. The observed high activity of 0.06 wt% polystyrene‐5.0Cu/γ‐Al₂O₃ catalyst was attributed to the role of polymer in enhancement of the degree of dispersion of the surface copper. However, the modification in kinetics of the reaction was attributed to the difference in the nature of Cu active sites namely, the polymer protected the metallic copper species on the surface of γ‐Al₂O₃ support against possible oxidation to copper sub‐oxides and/or that polymer might change the hydrophilic properties of the reaction media.     

焙烧气氛对Ru/Al2O3催化剂上甲烷部分氧化制合成气反应性能的影响

采用气相色谱、质谱和原位时间分辨红外光谱等技术对空气和Ar气氛中焙烧的Ru/Al2O3催化剂样品上甲烷部分氧化(POM)制合成气反应进行了跟踪,并采用化学吸附、X射线衍射、拉曼光谱和H2-程序升温还原等技术对催化剂进行了表征.结果表明,在Ru/Al2O3-Air上POM反应出现振荡现象,而在Ru/Al2O3-Ar上则可...     

Multiply Confined Nickel Nanocatalysts Produced by Atomic Layer Deposition for Hydrogenation Reactions

To design highly efficient catalysts, new concepts for optimizing the metal–support interactions are desirable. Here we introduce a facile and general template approach assisted by atomic layer deposition (ALD), to fabricate a multiply confined Ni‐based nanocatalyst. The Ni nanoparticles are not only confined in Al₂O₃ nanotubes, but also embedded in the cavities of Al₂O₃ interior wall. The cavities create more Ni–Al₂O₃ interfacial sites, which facilitate hydrogenation reactions. The nanotubes inhibit the leaching and detachment of Ni nanoparticles. Compared with the Ni‐based catalyst supported on the outer surface of Al₂O₃ nanotubes, the multiply confined catalyst shows a striking improvement of catalytic activity and stability in hydrogenation reactions. Our ALD‐assisted template method is general and can be extended for other multiply confined nanoreactors, which may have potential applications in many heterogeneous reactions.     

Shielded Sliding Discharge-Assisted Hydrocarbon Selective Catalytic Reduction of NOx over Ag/Al2O3 Catalysts Using Diesel as a Reductant

The nonthermal plasma generated in a shielded sliding discharge reactor was used to reform diesel for the hydrocarbon-selective catalytic reduction (HC-SCR) of NO_x on Ag/Al₂O₃ catalysts. Compared with raw diesel, the reformed diesel enhanced the NO_x reduction efficiency, mitigated hydrocarbon poisoning of the catalyst and reduced the fuel penalty for the HC-SCR reaction. The NO_x conversion values obtained with a commercial Ag/Al₂O₃ catalyst exceeded that of a 2.0 wt% Ag/Al₂O₃ catalyst prepared by wet impregnation. A significant amount of NH₃ was produced as a by-product during the HC-SCR reaction, which suggests that further NO_x conversion enhancement can be achieved by placing a second NH₃-SCR catalyst in series with the Ag/Al₂O₃ catalyst.     

Zur Kenntnis der künstlichen Alterung aluminiumhaltiger Eisen(III)-hydroxide

Study of the ageing process of amorphous ferric hydroxide has shown that the presence of traces of Al³⁺ can drastically change the course of the reaction under certain conditions. Al³⁺ traces delay crystallization, an effect which is dependant on the pH of the solution in which the originally amorphous gel is boiled. With increasing pH they favour the formation of the α-F₂O₃-phase, whereby the α-FeOOH modification, the formation of which should otherwise be favoured by the dehydrative conditions employed, is not formed at all. Inhibition of the formation of the α-FeOOH phase is already crystallographically detectable at a molar ratio of Al₂O₃/Fe₂O₃=0.001. The complete disappearance of this phase at pH=10 of the ageing medium is found at the molar ratio Al₂O₃/Fe₂O₃=0.03. At higher Al³⁺ concentrations the amorphous gel is converted into α-Fe₂O₃. In the range 10–20 mol% Al₂O₃, crystallization is strongly inhibited. Further increase in the Al³⁺ content favours the formation of Bayerite-phase, which then at 50 mol% Al predominantes, alongside poorly crystalline α-Fe₂O₃. For Al₂O₃/Fe₂O₃=0.55, three phases are present, hydrohematite, bayerite and boehmite. With still greater amounts of Al³⁺ only the boehmite modification is found. By stepwise crystallographic study of the progressive dehydration the duration of reaction has been established for ferric hydroxide both in the pure state and when doped with Al³⁺.     

Catalytic activity and physicochemical properties of Ni-Au/Al<Subscript>3</Subscript>CrO<Subscript>6</Subscript> system for partial oxidation of methane to synthesis gas

This work is focused on the role of gold and Al₃CrO₆ support for physicochemical properties, and catalytic activity of supported nickel catalysts in partial oxidation of methane (POM). Catalysts, containing 5% Ni and 5% Ni-2% Au active phases dispersed on mono- (Al₂O₃, Cr₂O₃) and bi-oxide Al₃CrO₆ support, were investigated by TPR, BET and XRD methods, and the activity tests in POM reaction were carried out. Bimetallic Ni-Au catalysts dispersed on Al₃CrO₆ support remained highly stable and active. The amorphous binary oxide Al₃CrO₆ can stabilize considerable amount of Cr⁴⁺, Cr⁵⁺, and Cr⁶⁺ species in Ni-Au/Al₃CrO₆ catalyst network during its calcination in the air. Nickel supported on binary oxide Ni/Al₃CrO₆ can form Ni(III)CrO₃ bi-oxide phase in reductive conditions. During TPR H2 reduction of Ni-Au/Al₃CrO₆ catalyst chromium(II) oxide Cr(II)O phase is observed. After POM reaction the existence of bimetallic Au-Ni alloy was experimentally confirmed on mono-oxide Al₂O₃ support surface, but its formation was not identified on bioxide Al₃CrO₆ support. Published in Russian in Kinetika i Kataliz, 2009, Vol. 50, No. 1, pp. 149–156. The article is published in the original. Based on a report at the VII Russ. Conf. on Mechanisms of Catalytic Reactions (with international participation), St. Petersburg, July 2–8, 2006.     

Direct synthesis of hydrogen peroxide from H2/O2 using Pd/Al2O3 catalysts

Pd/Al₂O₃ catalysts were prepared by the impregnation method and were used for the direct formation of hydrogen peroxide from H₂ and O₂. The H₂O₂ concentration and selectivity were strongly dependent on the solubility of hydrogen in the reaction medium. The modification of the support by halogenate has a beneficial effect on the selectivity. The state of the active Pd on Pd/Al₂O₃ catalysts was studied using X-ray photoelectron spectroscopy, and Pd(0) was found to be active.     

An iets study of alumina and magnesia supported —sihx and their use as substrates for inorganic vibrational spectroscopy

Tunneling spectra of Al₂O₃/—SiH_x, MgO/—SiH_x, Al₂O₃/—SiD_x, and Al₂O₃/—SiH_x + NCS^? are reported. Analysis of the vibrational spectra observed from isotopic substitution of the barriers obtained by deposition of a thin film of SiO onto alumina and magnesia indicate that the supported species is —SiH. The Al₂O₃/—SiH barrier can be used as a support for studying inorganic ions by IETS.     

Study on CuO/Al2O3 catalytic ozone treatment of acid red B solution

A CuO/Al₂O₃ catalyst was prepared using the impregnation method. The catalytic activity of CuO/Al₂O₃ for the ozonation of acid red B (ARB) in aqueous solution was studied, the chemical oxygen demand (COD) removal rate was an indicator for catalytic activity evaluation. The effects of initial ARB concentration, solution pH, and different oxidative degradation systems on oxidative degradation of ARB solution were studied. The CuO/Al₂O₃ catalyst was characterized using X‐ray diffractometry (XRD), N₂ adsorption desorption test, X‐ray photoelectron spectroscopy (XPS), and zero‐point charge (pH_zpc). The results show that copper species on the carrier were in the form of CuO and highly dispersed on the carrier. CuO can increase the alkalinity of the Al₂O₃ surface, and the CuO/Al₂O₃ catalyst facilitates the decomposition of O₃ into ·OH, which was beneficial for the catalytic O₃ oxidation degradation reaction. With the increase of the initial concentration of simulated wastewater, the CuO/Al₂O₃ catalytic reaction still has a high COD removal rate. Alkaline solution was of benefit to catalyze the degradation of ARB solution. When the ARB solution pH = 8.93, the degradation reaction was carried out for 40 min, the COD removal rate reached 83.2%. The degradation reaction was dominated by the hydroxyl radical (·OH) reaction.     

Influence of the Support on the Catalytic Characteristics of the Deposited Palladium in the Liquid-Phase Hydrogenation of Diphenylacetylene

Palladium catalysts on various types of supports were studied in the liquid-phase hydrogenation of diphenylacetylene. Samples of Pd/SiO₂–Al₂O₃, Pd/MgAl₂O₄, Pd/Al₂O₃, and Pd/TiO₂ were characterized by the chemisorption of the CO and IR spectroscopy of adsorbed CO. The use of n-hexane as the solvent increases the reaction rate, which can be explained by the better solubility of hydrogen in the liquid phase. It is established that the acid–base properties of the support do not affect the activity and selectivity of the catalysts in the reaction under study. However, they alter the electronic state of palladium. According to the catalytic tests, Pd/TiO₂ has the highest activity (turnover frequency) and selectivity to alkene. The comparison of the obtained catalytic data and the results of IR spectroscopy made it possible to conclude that this is due to the electron density redistribution between the palladium and TiO _x particles, which is caused by the strong metal–support interaction.     

Ni/Al2O3改性催化剂催化重整生物油模拟物制氢研究

制备了Ni/Al₂O₃、Ni-Cu/Al₂O₃、Ni-Co/Al₂O₃和Ni-Co-Cu/Al₂O₃催化剂,研究了Co和Cu对生物油水蒸气催化重整的影响。实验表明,Co 能促进水汽变换(WGS)反应,提高氢气的产率,Cu能抑制反应中焦炭的形成,提高催化剂的稳定性。对催化剂Ni-Co-Cu/Al₂O₃进行工艺条件考察,当900 ℃、水油比为6 g/g、质量空速(WHSV)为1 h^-1时,碳选择性达到87.5%,氢气产率达到84.2%,潜在氢气产率达到92.4%。     

Styrene polymerization in the presence of the CpTiCl3/Al2O3–SiO2/MAO catalytic system

Syndiotactic polymerization of styrene in the presence of heterogenized hemititanocene catalysts CpTiCl₃/Al₂O₃–SiO₂/MAO (Cp = cyclopentadienyl; MAO = methylaluminoxane) showed that the yield and selectivity of this reaction depend on the support composition, i.e. on the Al₂O₃ content in the support. The most active catalysts contained Al₂O₃ in a quantity of 50 to 70 wt%. Despite a relatively lower selectivity of 75–59%, the amount of syndiotactic polystyrene in the presence of those catalysts was the greatest. Copyright © 2002 John Wiley & Sons, Ltd.     

Catalytic Performance and Characterization of Pt‐Co/Al2O3 Catalysts for CO2 Reforming of CH4 to Synthesis Gas

Pt‐Co/Al₂O₂ catalyst has been studied for CO₂ reforming of CH₄ to synthesis gas. It was found that the catalytic performance of me catalyst was sensitive to calcination temperature. When Co/Al₂O₃ was calcined at 1473 K prior to adding a small amount of Pt to it, the resulting bimetallic catalyst showed high activity, optimal stability and excellent resistance to carbon deposition, which was more effective to the reaction than Co/Al₂O₃ and Pt/Al₂O₃ catalysts. At lower metal loading, catalyst activity decreased in the following order: Pt‐Co/ Al₂O₃ > Pt/Al₂O₃ > Co/Al₂O₃. With 9% Co, the Co/Al₂O₃ calcined at 923 K was also active for CO₂ reforming of CH₄, however, its carbon formation was much more fast man that of the Pt‐Co/Al₂O₃ catalyst. The XRD results indicated that Pt species well dispersed over the bimetallic catalyst. Its high dispersion was related to the presence of CoAl₂O₄, formed during calcining of Co/Al₂O₃ at high temperature before Pt addition. Promoted by Pt, Co/Al₂O₄ in the catalyst could be reduced partially even at 923 K, the temperature of pre‐reduction for the reaction, confirmed by TPR. Based on these results, it was considered that the zerovalent platinum with high dispersion over the catalyst surface and the zerovalent cobalt resulting from Co/Al₂O₄ reduction are responsible for high activity of the Pt‐Co/Al₂O₃ catalyst, and the remain Co/Al₂O₄ is beneficial to suppression of carbon deposition over the catalyst.     

Fabrication of inorganic alumina particles at nanoscale by a pulsed laser ablation technique in liquid and exploring their protein binding,anticancer and antipathogenic activities

The interaction of nanoparticles with biological systems can provide useful information about their therapeutic applications. The aluminum nanoparticles (Al₂O₃ NPs) were synthesized by laser ablation technique and well-characterized by different methods. Fluorescence spectroscopy, circular dichroism (CD) spectroscopy, and molecular docking studies were employed to evaluate the effect of Al₂O₃ NPs on the protein structure. Growth inhibitory and apoptotic effects of the Al₂O₃ NPs against K562 cancer cells and lymphocyte cells were assessed using [3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide] (MTT), flow cytometry, and real time polymerase chain reaction (PCR) assays. The antipathogenic activity of Al₂O₃ NPs against a diverse range of Gram-negative and Gram-positive pathogens was explored through a disk diffusion method. The characterization techniques determined that the Al₂O₃ NPs were successfully synthesized in the nanoscales. Intrinsic, 1-anilino-8-naphthalenesulfonate (ANS) and acrylamide fluorescence spectroscopy studies disclosed that Al₂O₃ NPs can partially change the tertiary structure of human serum albumin (HSA), whereas CD spectroscopy investigation depicted that the secondary structure of HSA remained intact. Molecular docking investigation also manifest that the Al₂O₃ nano-clusters preferably bind to electrostatic residues. Al₂O₃ NPs exhibited promising and selective anticancer features through reactive oxygen species (ROS) production, apoptosis induction, and elevation of Bax/Bcl-2 mRNA ratio. Furthermore, the Al₂O₃ NP showed a remarkable antibacterial activity against both Gram-negative and Gram-positive pathogens. In conclusion, it may be suggested that the synthesized Al₂O₃ NPs can be integrated in the development of anticancer and antipathogenic agents.     

Hydrodechlorination of chlorophenols over Pd catalysts supported on zeolite Y,MCM-41 and graphene

Hydrodechlorination (HDC) reaction of chlorophenols was carried out using Pd catalysts supported over zeolite Y, MCM-41 or graphene. Pd-MCM-41 and Pd-Y zeolite were prepared by impregnation and ion-exchange method, respectively. Pd-graphene (Pd-G) was prepared by hydrazine hydrate reduction of palladium ion dispersed on graphene oxide. The catalysts were characterized by several analytical tools such as X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDS). These catalysts were subjected to HDC reaction of chlorophenols, such as 4-chlorophenol (4-CP), 2,4-dichlorophenol (2,4-DCP), 2,6-dichlorophenol (2,6-DCP) and 3,4-dichlorophenol (3,4-DCP). The reaction rate of HDC of chlorophenols catalyzed by Pd catalysts with various solid bases, such as KF/Al₂O₃ (alumina), sodium acetate (NaOAc) and K₂CO₃ was compared. First, Pd-MCM-41 and Pd-Y catalysts were compared. 2,4- and 3,4-DCPs were completely decomposed within 6 h, in the case of Pd-MCM-41 with NaOAc. Using Pd-Y instead of Pd-MCM-41 with NaOAc, much faster decomposition was observed. Faster decomposition of 4-CP and DCPs was observed with NaOAc base than K₂CO₃ or KF/Al₂O₃ under the same condition. In the case of Pd-Y with KF/Al₂O₃, slower decomposition of 4-CP and DCPs was observed. These base effects were interpreted using the solubility of NaCl and KCl in alcohol and the basic sites of KF/Al₂O₃. Because the solubility of NaCl is known to be larger than KCl solubility in alcohol, byproduct NaCl could be easily dissolved and ionized in solvents. For Pd-Y with KF/Al₂O₃, the small pore size of Y zeolite can interfere with the diffusion of HCl to KF/Al₂O₃ basic site. Second, three catalysts, including Pd-graphene, were compared. 2,4-DCP was decomposed within 2 h using Pd-G with either K₂CO₃, NaOAc or KF/Al₂O₃. Pd-G catalyst showed the highest catalytic activity among Pd-G, Pd-MCM-41 and Pd-Y catalysts. The high activity and stability of the Pd-G could be attributed to the strong metal–support interaction with an electron-deficient site and a critical Pd particle size (ca. 3.5 nm) of Pd-G nanocatalyst with a stronger resistance to the deactivation and good affinity toward aromatic organic molecules, especially phenols. The progress of HDC reaction was monitored by gas chromatography with flame ionization detection (GC/FID), and a feasible degradation process could be explained by analyzing the degradation products such as phenol, cyclohexanone and cyclohexanol from resulting GC chromatograms. The effect of reaction temperature on HDC in Pd-G catalyst was also discussed. In conclusion, Pd-G is an efficient catalyst for decomposition of chlorophenols and can be applied to remediation of chlorophenol-contaminated water under mild conditions.     

Plasma catalytic reaction of natural gas to C2 product over Pd-NiO/Al2O3 and Pt-Sn/Al2O3 catalysts

The decomposition of natural gas over Pd-NiO/Al₂O₃ and Pt-Sn/Al₂O₃ is carried out in a microwave catalytic reaction at room temperature. The decomposition of methane is caused by collision by excitation of unstable electronic state. Measuring the flow rate and plasma power can provide kinetic data and indicate the mechanism. The conversion of C₂ products increases from 47 to 63.7% in the microwave plasma catalytic reaction with electric field. Comparing the activities of catalysts, Pd-NiO/Al₂O₃ bimetallic catalyst is more active than Pt-Sn/Al₂O₃ catalyst because of modification of the surface of catalysts by carbon formation. The kinetic modeling of plasma of methane conversion seems related to the power of the electric discharge. It was also revealed that proper coking or polymeric carbon formation improves the catalytic activity; therefore, the conversion of methane may increase over Pd-Ni/Al₂O₃ catalyst in the plasma system.     

Covalent Immobilization of Polyoxotungstate on Alumina and Its Catalytic Generation of Sulfoxides

The structural and chemical stabilities of immobilized polyoxometalate (POM)‐containing catalysts are crucial factors for their industrial application. An alumina supported POM catalyst is prepared by using a facile condensation reaction between the trilacunary POM Na₁₂[α‐P₂W₁₅O₅₆] ? 24 H₂O (P₂W₁₅) and the hydroxy groups on the surface of γ‐Al₂O₃ spheres under acidic conditions. The heterogeneous catalyst P₂W₁₅?Al₂O₃ is characterized by a wide variety of techniques and shows excellent stability and highly efficient reactivity and selectivity for the oxygenation of thioethers to sulfoxides, which are a very useful intermediate in organic synthesis and the industrial preparation of drugs. Furthermore, P₂W₁₅?Al₂O₃ can be recycled and reused at least ten times without any observable loss of its catalytic efficiency, mainly due to the covalent immobilization and high dispersion of P₂W₁₅ on the γ‐Al₂O₃ surface.     

Study of benzene hydrogenation catalyzed by nickel supported on alumina in a fixed bed reactor

The Ni/Al₂O₃ catalysts were prepared for studying benzene hydrogenation. It was observed that the activity for Ni loading under 5% is very low due to the formation of nickel aluminate (spinel) in low nickel loading. It has been found that Ni/Al₂O₃ systems exhibit SMSI (strong-metal support interaction) to a much lesser extent. It could be concluded that the hydrogenation of benzene on supported Ni catalysts is a structure insensitive reaction.