Recent progress in the electrolytes for improving the cycling stability of LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> high-voltage cathode

High-voltage spinel LiNi_0.5Mn_1.5O₄ has been considered one of the most promising cathode materials for lithium-ion power batteries used in electrical vehicles (EVs) or hybrid electrical vehicles (HEVs) because the high voltage plateau at around 4.7 V makes its energy density (658 Wh kg^?1) 30 and 25 % higher than that of conventional pristine spinel LiMn₂O₄ (440 Wh kg^?1) or olivine LiFePO₄ (500 Wh kg^?1) materials, respectively. Unfortunately, LiNi_0.5Mn_1.5O₄-based batteries with LiPF₆-based carbonate electrolytes always suffer from severe capacity deterioration and poor thermostability because of the oxidization of organic carbonate solvents and decomposition of LiPF₆, especially at elevated temperatures and water-containing environment. The major goal of this review is to highlight the recent advancements in the development of advanced electrolytes for improving the cycling stability and rate capacity of LiNi_0.5Mn_1.5O₄-based batteries. Finally, an insight into the future research and further development of advanced electrolytes for LiNi_0.5Mn_1.5O₄-based batteries is discussed.     

Cells studies on PEO/PEG/NaClO<Subscript>3</Subscript> thin-film electrolyte system based on composite V<Subscript>2</Subscript>O<Subscript>5</Subscript> electrode

The thin-film solid polymer electrolyte based on polyethylene oxide (PEO) with sodium chlorite (NaClO₃) has been prepared by a solution-cast technique. The electrolyte was characterized by X-ray diffraction (XRD), infrared (IR), cyclic voltammetry, alternating current conductivity, and Wagner’s polarization studies. The complexation of NaClO₃ with PEO was confirmed through the XRD and IR studies. The transference number measurement has shown that the ion transport is predominant over electrons in the polymer electrolytes (t _ions ≈ 0.94). The conductivity enhancement was observed in the case of the PEO/NaClO₃ system with the addition of plasticizers (low-molecular-weight polyethylene glycol, organic solvents propylene carbonate and dimethyl formamide. Cyclic voltammetry analysis showed the stability and redox character of the electrolyte and electrode. Finally, polymer electrolyte systems were examined by electrochemical cell studies using V₂O₅ and composite V₂O₅ cathode at temperature of 35 °C. Overall, the plasticized electrolyte shows a better electrochemical performance, and a higher discharge capacity was observed in composite V₂O₅-based cells over V₂O₅-based cells.     

Lithium polyacrylate-coated LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cathode materials with excellent performance for lithium ion batteries

A novel facile approach to coat LiMn₂O₄ by lithium polyacrylate (PAALi) is demonstrated. The PAALi-coated LiMn₂O₄ (LMO@2%PAALi) and LiMn₂O₄ (LMO) are characterized by charge–discharge tests, X-ray diffraction (XRD), PAALi dissolving experiment, transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), thermogravimetry (TG), and inductively coupled plasma optical emission spectrometer (ICP-OES). XRD and FTIR analyses indicate that there are no clear differences between LMO@2%PAALi and LMO. PAALi dissolving experiment indicates that PAALi is indissolvable in LiPF₆-EC/DMC/EMC electrolyte. TEM results reveal that LiMn₂O₄ particles are coated by PAALi. ICP-OES results indicate that this stable PAALi coating can prevent the Mn ions dissolving from active LiMn₂O₄ materials and then the stability of LiMn₂O₄ crystals in electrolyte are greatly enhanced. These unique features ensure that LMO@2%PAALi possesses much better rate performance, higher discharge capacity, better cycling performance, and lower charge transfer resistance over LMO. The discharge capacity of LMO@2%PAALi at 0.2 C reaches up to 127.2 mAh g^?1 at room temperature.     

Vibrational,electrical, and ion transport properties of PVA-LiClO<Subscript>4</Subscript>-sulfolane electrolyte with high cationic conductivity

Novel solid polymer electrolytes, poly(vinylalcohol)-lithium perchlorate (PVA-LiClO₄) and PVA-LiClO₄-sulfolane are prepared by solvent casting method. The experimental results show that sulfolane addition enhances the ionic conductivity of PVA-LiClO₄ complex by three orders. The maximum ionic conductivity of 1.14 ± 0.20 × 10^?2 S cm^?1 is achieved for 10 mol% sulfolane-added electrolyte at ambient temperature. Polymer-salt-plasticizer interactions are analyzed through attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy. Lithium ion transference number is found by AC impedance spectroscopy combined with DC potentiostatic measurements. The results confirm that sulfolane improves the Li⁺ transference number of PVA-LiClO₄ complex to 0.77 from 0.40. The electrochemical stability window of electrolytes is determined by cyclic voltammetry (CV). The broad electrochemical stability window of 5.45 V vs. lithium is obtained for maximum conducting electrolyte. All-solid-state cell is fabricated using maximum conducting electrolyte, and electrochemical impedance study is carried out. It reveals that electrolyte interfacial resistance with Li electrode is very low. The use of PVA-LiClO₄-sulfolane as a viable electrolyte material for high-voltage lithium ion batteries is ensured.     

Investigation of the synergetic effects of LiBF<Subscript>4</Subscript> and LiODFB as wide-temperature electrolyte salts in lithium-ion batteries

Herein, we present the use of lithium tetrafluoroborate (LiBF₄) as an electrolyte salt for wide-temperature electrolytes in lithium-ion batteries. The research focused on the application of blend salts to exhibit their synergistic effect especially in a wide temperature range. In the study, LiCoO₂ was employed as the cathode material; LiBF₄ and lithium difluoro(oxalate)borate (LiODFB) were added to an electrolyte consisting of ethylene carbonate (EC), propylene carbonate (PC), and ethyl methyl carbonate (EMC). The electrochemical performance of the resulting electrolyte was evaluated through various analytical techniques. Analysis of the electrical conductivity showed the relationship among solution conductivity, the electrolyte composition, and temperature. Cyclic voltammetry (CV), charge-discharge cycling, and AC impedance measurements were used to investigate the capacity and cycling stability of the LiCoO₂ cathode in different electrolyte systems and at different temperatures. Scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) were applied to analyze the surface properties of the LiCoO₂ cathode after cycling. The results indicated that the addition of a small amount of LiODFB into the LiBF₄-based electrolyte system (LiBF₄/LiODFB of 8:2) may enhance the electrochemical performance of the LiCoO₂ cell over a relatively wide temperature range and improve the cyclability of the LiCoO₂ cell at 60 °C.     

Improving the rate performance and stability of LiNi<Subscript>0.6</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.2</Subscript>O<Subscript>2</Subscript> in high voltage lithium-ion battery by using fluoroethylene carbonate as electrolyte additive

Fluoroethylene carbonate (FEC) is investigated as the electrolyte additive to improve the electrochemical performance of high voltage LiNi_0.6Co_0.2Mn_0.2O₂ cathode material. Compared to LiNi_0.6Co_0.2Mn_0.2O₂/Li cells in blank electrolyte, the capacity retention of the cells with 5 wt% FEC in electrolytes after 80 times charge-discharge cycle between 3.0 and 4.5 V significantly improve from 82.0 to 89.7%. Besides, the capacity of LiNi_0.6Co_0.2Mn_0.2O₂/Li only obtains 12.6 mAh g^?1 at 5 C in base electrolyte, while the 5 wt% FEC in electrolyte can reach a high capacity of 71.3 mAh g^?1 at the same rate. The oxidative stability of the electrolyte with 5 wt% FEC is evaluated by linear sweep voltammetry and potentiostatic data. The LSV results show that the oxidation potential of the electrolytes with FEC is higher than 4.5 V vs. Li/Li⁺, while the oxidation peaks begin to appear near 4.3 V in the electrolyte without FEC. In addition, the effect of FEC on surface of LiNi_0.6Co_0.2Mn_0.2O₂ is elucidated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). The analysis result indicates that FEC facilitates the formation of a more stable surface film on the LiNi_0.6Co_0.2Mn_0.2O₂ cathode. The electrochemical impedance spectroscopy (EIS) result evidences that the stable surface film could improve cathode electrolyte interfacial resistance. These results demonstrate that the FEC can apply as an additive for 4.5 V high voltage electrolyte system in LiNi_0.6Co_0.2Mn_0.2O₂/Li cells.     

Electrochemical properties of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> prepared with tartaric acid chelating agent

Lithium manganese oxide (LiMn₂O₄) has been prepared using sol-gel technique under acidic (pH = 5.8) and alkaline (pH = 9) conditions with tartaric acid as chelating agent. X-ray studies show that under acidic condition, an Mn₂O₃ peak was observed indicating the presence of impurities. No impurity was observed for LiMn₂O₄ under alkaline conditions. The particle size is mostly in the range of 124 to 185 nm from HR-TEM. The lithium diffusion coefficient, D _Li+ in LiMn₂O₄ is of the order 10^?9 cm² s^?1. By using density functional theory (DFT) calculations, structural properties have been obtained. The specific discharge capacity of the cells with LiMn₂O₄ prepared under alkaline condition and with LiMn₂O₄ prepared under acidic condition discharged at 0.5 C is in the ranges of 132 to 142 and 128 to 139 mAh g^?1, respectively.     

Synthesis,structure, and electrochemistry of Ag-modified LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cathode materials for lithium-ion batteries

The composite of silver-modified lithium manganese oxide were prepared using thermal decomposition method of different mole ratio. Structural characterization was carried out by X-ray diffraction (XRD). XRD analysis revealed different patterns as the content of the dopant in the spinel increases. Phase analysis shows that Ag particles were dispersed on the LiMn₂O₄ surface instead of entering the spinel structure. On the other hand, the electrochemical behavior of cathode powder was examined by using two-electrode test cells consisting of a cathode, metallic lithium as anode, and a solid polymer electrolyte of 0.87PEO-0.13LiCF₃SO₃-0.10DBP. According to the electrochemical tests results, the influence of the Ag additive content on the electrochemical properties of Ag/LiMn₂O₄ composites is clearly shown.     

Preparation and characterization of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> nanorod by low heating solid state coordination method

Cathode material LiMn₂O₄ nanorod was prepared by annealing of the mixed precursor which was synthesized by low heating solid state coordination method using lithium acetate, manganese acetate and oxalic acid as starting materials. The structures and morphologies of the LiMn₂O₄ nanorod were investigated as a function of annealing temperature and time. The results showed that all samples in different annealing temperatures and time have the same spinel structure. The higher the annealing temperature is, the more complete the crystal structure forms, and the larger the particle size is. In addition, the electrochemical properties of the LiMn₂O₄nanorod were studied in this paper.     

An approach to improve the electrochemical performance of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> at high temperature

In order to overcome the severe capacity decay of LiMn₂O₄ at high temperature, TiN is used as an active materials additive in this paper. The XRD and XPS test results indicate that the TiN can effectively prevent Mn from dissolving in electrolyte; galvanostatic charge-discharge test shows that LiMn₂O₄ electrode with TiN exhibits remarkably improved capacity retention at high temperature with capacity of 105.1 mAh g^?1 at 1 C in the first cycle at 55 °C and the capacity maintains 88.9% retention after 150 cycles. And the electrochemical impedance spectroscopy result demonstrates TiN’s effectiveness in easing the increase of charge-transfer resistance during cycling. Therefore, we can conclude that TiN, as an addictive, made obvious contribution to the greatly improved electrochemical cycling performance of LiMn₂O₄.     

Synthesis and characterization of spinel LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles prepared by high-energy milling and hydrothermal method

Spinel LiMn₂O₄ has been known to be a technologically important, environmental-friendly, and low-cost cathode material used in Li-based rechargeable batteries, and it is also widely available. Nanoparticle spinel LiMn₂O₄ has been synthesized by the top-down, high-energy milling, and hydrothermal methods. SEM images, X-ray diffraction patterns, and neutron high-resolution powder diffraction patterns have confirmed the nanocrystalline nature of the spinel LiMn₂O₄ samples. Raman and Fourier transform infrared (FTIR) measurements show typical absorption and vibration spectra typical for the spinel LiMn₂O₄ showing the formation of various metallic bonds in the sample. The strongest Raman and FTIR signals come from the higher frequency region, with weaker signals appearing in the lower frequency range.     

Elevated electrochemical property of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> originated from nano-sized Mn<Subscript>3</Subscript>O<Subscript>4</Subscript>

By employment of nano-sized pre-prepared Mn₃O₄ as precursor, LiMn₂O₄ particles have been successfully prepared by facile solid state method and sol-gel route, respectively. And the reaction mechanism of the used precursors of Mn₃O₄ is studied. The structure, morphology, and element distribution of the as-synthesized LiMn₂O₄ samples are characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). Compared with LiMn₂O₄ synthesized by facile solid state method (SS-LMO), LiMn₂O₄ synthesized by modified sol-gel route (SG-LMO) possesses higher crystallinity, smaller average particle size (~175 nm), higher lithium chemical diffusion coefficient (1.17 × 10^?11 cm² s^?1), as well as superior electrochemical performance. For example, the cell based on SG-LMO can deliver a capacity of 85.5 mAh g^?1 at a high rate of 5 °C, and manifests 88.3% capacity retention after 100 cycles at 0.5 °C when cycling at 45 °C. The good electrochemical performance of the cell based on SG-LMO is ascribed mainly to its small particle size, high degree of dispersion, and uniform element distribution in bulk material. In addition, the lower polarization potential accelerates Li⁺ ion migration, and the lower atom location confused degree maintains integrity of crystal structure, both of which can effectively improve the rate capability and cyclability of SG-LMO.     

ZnO-coated LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cathode material for lithium-ion batteries synthesized by a combustion method

ZnO-coated LiMn₂O₄ cathode materials were prepared by a combustion method using glucose as fuel. The phase structures, size of particles, morphology, and electrochemical performance of pristine and ZnO-coated LiMn₂O₄ powders are studied in detail by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), galvanostatic charge-discharge test, and X-ray photoelectron spectroscopy (XPS). XRD patterns indicated that surface-modified ZnO have no obvious effect on the bulk structure of the LiMn₂O₄. TEM and XPS proved ZnO formation on the surface of the LiMn₂O₄ particles. Galvanostatic charge/discharge test and rate performance showed that the ZnO coating could improve the capacity and cycling performance of LiMn₂O₄. The 2 wt% ZnO-coated LiMn₂O₄ sample exhibited an initial discharge capacity of 112.8 mAh g^?1 with a capacity retention of 84.1 % after 500 cycles at 0.5 C. Besides, a good rate capability at different current densities from 0.5 to 5.0 C can be acquired. CV and EIS measurements showed that the ZnO coating effectively reduced the impacts of polarization and charge transfer resistance upon cycling.     

Hydrothermal synthesis of pure LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> from nanostructured MnO<Subscript>2</Subscript> precursors for aqueous hybrid supercapacitors

Pure LiMn₂O₄ samples with high crystallinity (LMO-1# and LMO-2#) were successfully synthesized by a facile hydrothermal method using δ-MnO₂ nanoflowers and α-MnO₂ nanowires as the precursors. The as-prepared samples were analyzed by XRD, SEM, and Brunauer-Emmett-Teller (BET), and their capacitive properties were investigated by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge/discharge test. Two LiMn₂O₄ samples showed good capacitive behavior in aqueous hybrid supercapacitors. AC//LMO-1# and AC//LMO-2# delivered the initial specific capacitance of 45.4 and 40.7 F g^?1 in 1 M Li₂SO₄ electrolyte at a current density of 200 mA g^?1 in the potential range of 0～1.5 V, respectively. After 1000 cycles, the capacitance retention was 97.6% for AC//LMO-1# and 93.7% for AC//LMO-2#. Obviously, LMO-1# from δ-MnO₂ nanoflowers exhibited higher specific capacitance and better cycling performance than LMO-2#, so LMO-1# was more suitable as the positive electrode material in hybrid supercapacitors.     

Effect of sulfolane and lithium bis(oxalato)borate-based electrolytes on the performance of spinel LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cathodes at 55 °C

To seek a promising candidate electrolyte at elevated temperature for lithium manganese oxide (LiMn₂O₄)/Li cells, the electrochemical performance of 0.7 mol L^?1 LiBOB (lithium bis(oxalate)borate)-SL (sulfolane)/DEC (diethyl carbonate) (1:1, in volume) electrolyte was studied at 55 °C. The Mn dissolution in electrolyte was analyzed by inductively coupled plasma (ICP) analysis. AC impedance measurement and scanning electron microscopy (SEM) analysis were used to analyze the formation of the surface film on the LiMn₂O₄ electrode. The results demonstrate that the LiBOB-SL/DEC electrolyte can slow down the dissolution and erosion of Mn ions, and decrease the interface impedance. Moreover, the LiBOB-SL/DEC electrolyte could obviously improve the capacity retention, the operating voltage (4.05 V), and the rate performance of LiMn₂O₄/Li cells.     

Synthesis and electrochemical performance of LiFePO<Subscript>4</Subscript>/C cathode materials from Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> for high-power lithium-ion batteries

Carbon-coated olivine-structured LiFePO₄/C composites are synthesized via an efficient and low-cost carbothermal reduction method using Fe₂O₃ as iron source at a relative low temperature (600 °C). The effects of two kinds of carbon sources, inorganic (acetylene black) and organic (sucrose), on the structures, morphologies, and lithium storage properties of LiFePO₄/C are evaluated in details. The particle size and distribution of the carbon-coated LiFePO₄ from sucrose (LiFePO₄/SUC) are more uniform than that obtained from acetylene black (LiFePO₄/AB). Moreover, the LiFePO₄/SUC nanocomposite shows superior electrochemical properties such as high discharge capacity of 156 mAh g^?1 at 0.1 C, excellent cyclic stability, and rate capability (78 mAh g^?1 at 20 C), as compared to LiFePO₄/AB. Cyclic voltammetric test discloses that the Li-ion diffusion, the reversibility of lithium extraction/insertion, and electrical conductivity are significantly improved in LiFePO₄/SUC composite. It is believed that olivine-structured LiFePO₄ decorated with carbon from organic carbon source (sucrose) using Fe₂O₃ is a promising cathode for high-power lithium-ion batteries.     

Synthesis of macroporous LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> with avian egg membrane as a template

Avian eggshell membrane as a template for the synthesis of a macroporous network of crystalline LiMn₂O₄ is demonstrated. Well-formed crystals of average size 600 nm formed a network structure whose average pore size was 2–4 μm. The unique porous structure should make it an attractive cathode material for lithium-ion batteries. In fact, for an 80% cutoff in capacity retention, LiMn₂O₄ obtained by a 10-h calcination at 800°C sustained 83 cycles.     

A lithium salt additive Li<Subscript>2</Subscript>ZrF<Subscript>6</Subscript> for enhancing the electrochemical performance of high-voltage LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode

In this work, Li₂ZrF₆, a lithium salt additive, is reported to improve the interface stability of LiNi_0.5Mn_1.5O₄ (LNMO)/electrolyte interface under high voltage (4.9 V vs Li/Li⁺). Li₂ZrF₆ is an effective additive to serve as an in situ surface coating material for high-voltage LNMO half cells. A protective SEI layer is formed on the electrode surface due to the involvement of Li₂ZrF₆ during the formation of SEI layer. Charge/discharge tests show that 0.15 mol L^?1 Li₂ZrF₆ is the optimal concentration for the LiNi_0.5Mn_1.5O₄ electrode and it can improve the cycling performance and rate property of LNMO/Li half cells. The results obtained by electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS) demonstrate that Li₂ZrF₆ can facilitate the formation of a thin, uniform, and stable solid electrolyte interface (SEI) layer. This layer inhibits the oxidation decomposition of the electrolyte and suppresses the dissolution of the cathode materials, resulting in improved electrochemical performances.     

Lithiated c-V<Subscript>2</Subscript>O<Subscript>5</Subscript> thin-film as positive electrode for rocking-chair solid-state lithium microbattery

We report for the first time the use of lithiated crystalline V₂O₅ thin films as positive electrode in all-solid-state microbatteries. Crystalline Li_xV₂O₅ films (x ≈ 0.8 and 1.5) are obtained by vacuum evaporation of metallic lithium deposited on sputtered c-V₂O₅. An all-solid-state lithium microbattery of Li_1.5V₂O₅/LiPON/Li exhibited a typical reversible capacity of 50 μAh/cm² in the potential range 3.8/2.15 V which exceeds by far the results known on all-solid-state lithium batteries using amorphous V₂O₅ films and lithiated amorphous Li_xV₂O₅ thin films as positive electrode. Hence, the present work opens the possibility of using high performance crystalline lithiated V₂O₅ thin films in rocking-chair solid-state microbatteries.     

Structural disordering in Cr-doped Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> spinels

The processes of lithium redistribution in the structure of cubic Li₄Ti₅O₁₂ spinel, caused by both chromium doping and thermal activation, have been investigated by nuclear magnetic resonance. It is shown that Li ions migrate from tetra- to octahedral crystallographic positions with an increase in temperature. This process becomes more pronounced at temperatures above 400 K. In contrast, the fraction of tetrahedrally coordinated Li increases as a result of doping with chromium.