L‐Cysteine Voltammetry at a Carbon Paste Electrode Bulk‐Modified with Ferrocenedicarboxylic Acid

The electrochemical behavior of L ‐cysteine studied at the surface of ferrocenedicarboxylic acid modified carbon paste electrode (FDCMCPE) in aqueous media using cyclic voltammetry, differential pulse voltammetry and double potential step chronoamperometry. It has been found that under optimum condition (pH 8.00) in cyclic voltammetry, the oxidation of L ‐cysteine occurs at a potential about 200 mV less positive than that of an unmodified carbon paste electrode. The kinetic parameters such as electron transfer coefficient, α, and catalytic reaction rate constant, k_h were also determined using electrochemical approaches. The electrocatalytic oxidation peak current of L ‐cysteine showed a linear dependent on the L ‐cysteine concentration and linear analytical curves were obtained in the ranges of 3.0×10^?5 M–2.2×10^?3 M and 1.5×10^?5 M–3.2×10^?3 M of L ‐cysteine concentration with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods respectively. The detection limits (3σ) were determined as 2.6×10^?5 M and 1.4×10^?6 M by CV and DPV methods.     

Estimation of Coupling Rate Constant of L‐Cysteine Radical Studied by Concentration‐Step Coulometry Using Porous Carbon Felt Electrode Impregnated with an Electrolyte

Controlled potential coulometry using carbon felt electrode impregnated with electrolytic solution realizes very rapid complete electrolysis and can be used to measure the faster reaction rate constant than that using conventional electrolytic cell. In this research, concentration step method was adopted to investigate coupling reaction rate of L ‐cysteine radical. The coupling reaction rate of L ‐cysteine radical becomes much larger than further electrode reaction rate of L ‐cysteine radical at high L ‐cysteine concentration, because the coupling reaction rate is proportional to the second order of L ‐cysteine radical concentration although the further electrode reaction rate is proportional to the first order of L ‐cysteine radical concentration. At a low constant potential value, apparent number of electrons (n_app) increased from 1 (L ‐cystine is produced) to 2 (L ‐cysteine sulfenic acid, RSOH, may be produced) according to decrease in concentration of L ‐cysteine to be electrolyzed. The second order rate constant of coupling reaction was estimated to be about 1200 dm³ mol^?1 s^?1 at 20 °C by curve fitting method for n_app vs. logarithm of L ‐cysteine concentration. Apparent number of electrons (n_app) consumed in the electrode oxidation of L ‐cysteine gradually increased as an applied potential increases, because the consecutive electrode reaction steps with different electrode reaction rates were involved in the electrode oxidation of L ‐cysteine. In the present method, the constant limited electrolytic current was observed at high electrode potential range, which suggests that electrode oxidation rate of L ‐cysteine is kinetically controlled.     

Electrochemical oxidation of isoniazid catalyzed by (FcM)TMA at the platinum electrode and its practical analytical application

The electrocatalytic oxidation of isoniazid (INH) by (ferrocenylmethyl)trimethylammonium [(FcM)TMA] at the platinum electrode in 0.10 M Na₂SO₄ aqueous solution was studied by cyclic voltammetry (CV). Although INH itself showed a very poor electrochemical response at the platinum electrode, the response could be greatly enhanced by using (FcM)TMA as a mediator, which enables a sensitive electrochemical determination of the substrate INH. The reaction rate constant for catalytic oxidation reaction was evaluated as (3.98±0.10)×10³ M⁻¹ s⁻¹ by using chronoamperometry (CA). Experimental conditions such as supporting electrolyte and its concentration, solution pH, and the concentrations of the catalyst (FcM)TMA and the substrate INH were investigated to maximize the current efficiency of the electrocatalytic oxidation. The method can be used for the sensitive practical determination of INH, and also opens an avenue for using (FcM)TMA as a mediator in electroanalytical determination which is very simple, cheap, and rapid. Furthermore, no sample pretreatment or time-consuming extraction steps are required prior to the analysis.     

Electrocatalytic Characteristics of Ferrocenecarboxylic Acid Modified Carbon Paste Electrode in the Oxidation and Determination of L‐Cysteine

The electrochemical behavior of L ‐cysteine studied at the surface of ferrocenecarboxylic acid modified carbon paste electrode (FCMCPE) in aqueous media using cyclic voltammetry and double step potential chronoamperometry. It has been found that under optimum condition (pH 7.00) in cyclic voltammetry, the oxidation of L ‐cysteine is occurs at a potential about 580 mV less positive than that an unmodified carbon paste electrode. The kinetic parameters such as electron transfer coefficient, α and catalytic reaction rate constant, K′_h were also determined using electrochemical approaches. The electrocatalytic oxidation peak current of L ‐cysteine showed a linear dependent on the L ‐cysteine concentration and linear calibration curves were obtained in the ranges of 10^?5 M–10^?3 M and 4.1×10^?8 M–3.7×10^?5 M of L ‐cysteine concentration with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods respectively. The detection limits (2δ) were determined as 2.4×10^?6 M and 2.5×10^?8 M by CV and DPV methods. This method was also examined for determination of L ‐cysteine in some samples, such as Soya protein powder, serum of human blood by using recovery and standard addition methods.     

In Vivo Monitoring of the Thiols in Rat Striatum by Liquid Chromatography with Amperometric Detection at a Functionalized Multi‐Wall Carbon Nanotubes Modified Electrode

A new chemically modified electrode (CME) was fabricated, which was based on the immobilization of multi‐wall carbon nanotubes fuctionalized with carboxylic group (MWNT‐COOH). The results indicated that the CME exhibited efficiently electrocatalytic oxidation for L ‐cysteine and glutathione with relatively high sensitivity, stability and long‐life. Coupled with HPLC, the MWNT‐COOH CME was utilized for amperometric detection of the thiols. The peak currents of L ‐cysteine and glutathione were linear to their concentrations ranging from 3.0×10^?7 to 1.0×10^?3 mol/L with the calculated detection limit (S/N=3) of 1.2×10^?7, 2.2×10^?7 mol/L, respectively. The method had been successfully applied to assess the contents of L ‐cysteine and glutathione in rat striatal microdialysates.     

Development of a Carbon Paste Electrode Modified with Reduced Graphene Oxide and an Imidazole Derivative for Simultaneous Determination of Biological Species of N‐acetyl‐L‐cysteine,Uric Acid and Dopamine

In this work, the modified carbon paste electrode (CPE) with an imidazole derivative 2‐(2,3 dihydroxy phenyl) 4‐methyl benzimidazole (DHPMB) and reduced graphene oxide (RGO) was used as an electrochemical sensor for electrocatalytic oxidation of N‐acetyl‐L‐cysteine (NAC). The electrocatalytic oxidation of N‐acetyl‐L‐cysteine on the modified electrode surface was then investigated, indicating a reduction in oxidative over voltage and an intensive increase in the current of analyte. The scan rate potential, the percentages of DHPMB and RGO, and the pH solution were optimized. Under the optimum conditions, some parameters such as the electron transfer coefficient (α) between electrode and modifier, and the electron transfer rate constant) k_s) in a 0.1 M phosphate buffer solution (pH=7.0) were obtained by cyclic voltammetry method. The diffusion coefficient of species (D) 3.96×10^?5 cm² s^?1 was calculated by chronoamperometeric technique and the Tafel plot was used to calculate α (0.46) for N‐ acetyl‐L‐cysteine. Also, by using differential pulse voltammetric (DPV) technique, two linear dynamic ranges of 2–18 µM and 18–1000 µM with the detection limit of 61.0 nM for N‐acetyl‐L‐cysteine (NAC) were achieved. In the co‐existence system of N‐acetyl‐L‐cysteine (NAC), uric acid (UA) and dopamine (DA), the linear response ranges for NAC, UA, and DA are 6.0–400.0 µM, 5.0–50.0 µM and 2.0–20.0 µM, respectively and the detection limits based on (C=3s_b/m) are 0.067 µM, 0.246 µM and 0.136 µM, respectively. The obtained results indicated that DHPMB/RGO/CPE is applicable to separate NAC, uric acid (UA) and dopamine (DA) oxidative peaks, simultaneously. For analytic performance, the mentioned modified electrode was used for determination of NAC in the drug samples with acceptable results, and the simultaneous determination of NAC, UA and DA oxidative peaks was investigated in the serum solutions, too.     

Preparation and Electrochemical Behaviour of Silver Pentacyanonitrosylferrate Film Modified Glassy Carbon Electrode and Its Electrocatalytic Oxidation to L‐cysteine

A glassy carbon (GC) electrode modified with silver pentacyanonitrosylferrate (AgPCNF) film as a redox mediator was fabricated. Cyclic voltammetry was used to study the redox property of AgPCNF modified electrode. The modified electrode showed a well‐defined redox couple due to [Ag^IFe^III/II(CN)₅NO]^1‐/2‐system. The effects of scan rates, supporting electrolytes and solution pHs were studied on the electrochemical behavior of the modified electrode. The feasibility of using the AgPCNF modified electrode to measure L ‐cysteine was investigated. It showed an excellent electrocatalytic activity towards the oxidation of L ‐cysteine and the anodic currents were proportional to the L ‐cysteine concentration in the range of 0.1 μM to 20 μM, the linear regression equation is I_pa(μA) = ‐68.58 ‐ 5.78C_{L ‐cysteine} (μM), with a correlation coefficient 0.998 for N = 23. The detection limit was down to 3.5 × 10^‐8 M (three times the ratio of signal to noise).     

Electrocatalytical Oxidation of Nitrite and Its Determination Based on Au@Fe3O4 Nanoparticles

A promising electrochemical nitrite sensor was fabricated by immobilizing Au@Fe₃O₄ nanoparticles on the surface of L ‐cysteine modified glassy carbon electrode, which was characterized by scanning electron microscopy, X‐ray photoelectron spectroscopy, electrochemical impedance spectroscopy and cyclic voltammetry. The proposed sensor exhibited excellent electrocatalytic activity toward nitrite oxidation. The kinetic parameters of the electrode reaction process were calculated, (1–α)n_α was 0.38 and the heterogeneous electron transfer coefficient (k) was 0.13 cm s^?1. The detection conditions such as supporting electrolyte and pH value were optimized. Under the optimized conditions, the linear range for the determination of nitrite was 3.6×10^?6 to 1.0×10^?2 M with a detection limit of 8.2×10^?7 M (S/N=3). Moreover, the as‐prepared electrode displayed good stability, repeatability and selectivity for promising practical applications.     

The Electrocatalytic Oxidation of Thymine at α‐Cyclodextrin Incorporated Carbon Nanotube‐Coated Electrode

Electrocatalytic oxidation of thymine at α‐cyclodextrin (α‐CD) incorporated carbon nanotube‐coated electrode (CNT/CE) was thoroughly studied in alkaline media. CNT showed an electrocatalytic effect on the oxidation of thymine, formation of a supramolecular inclusion complex between α‐CD and thymine at CNT/CE further enhanced the sensitivity to thymine. The electrocatalytic behavior was further developed as a sensitive detection scheme for thymine by differential pulse voltammetry. A linear calibration over the concentration range from 2.5×10^?5 to 1.8×10^?3 mol/L in pH 10.8 NaHCO₃‐Na₂CO₃ buffer solution was obtained with a detection limit of 5×10^?6 mol/L.     

Synthesis and Characterization of Chromium Hexacyanoferrate/Multiwalled Carbon Nanotube Composite and Its Biosensing for L‐Cysteine

This work describes the electrochemical properties of glassy carbon electrodes (GCE) modified with chromium(III) hexacyanoferrate(II) (Crhf) nanoparticles attached multiwalled carbon nanotube (MWNTs). The morphological characterization of Crhf/MWNTs nanocomposites was examined by scanning electron microscopy (SEM), UV‐vis spectroscopy, and Fourier transform infrared spectrometry (FT‐IR). The electrocatalytic activity of these nanocomposites was investigated and showed a good electrocatalytic effect for oxidation of L ‐cysteine (L ‐Cys) in 0.1 M phosphate buffer solution (pH 3.0). Under optimum conditions linear calibration graphs were obtained over the L ‐Cys concentration range 5.0×10^?7 to 6.0×10^?5 M with a correlation coefficient of 0.9998 and a detection limit (signal‐to‐noise ratio was 3) of 1.0×10^?8 M. The proposed method is simple and it also showed excellent sensitivity and stability. The excellent electrocatalytic ability of the modified electrode towards L ‐Cys manifests that the Crhf/MWNTs can provide a new platform for biosensors and other biology.     

Electrocatalytic Oxidation and Voltammetric Determination of L‐Cysteic Acid at the Surface of p‐Bromanil Modified Carbon Paste Electrode

The electrochemical properties of L ‐cysteic acid studied at the surface of p‐bromanil (tetrabromo‐p‐benzoquinone) modified carbon paste electrode (BMCPE) in aqueous media by cyclic voltammetry (CV) and double step potential chronoamperometry. It has been found that under optimum condition (pH 7.00) in cyclic voltammetry, the oxidation of L ‐cysteic acid at the surface of BMCPE occurs at a half‐wave potential of p‐bromanil redox system (e.g., 100 mV vs. Ag|AgCl|KCl_sat), whereas, L ‐cysteic acid was electroinactive in the testing potential ranges at the surface of bare carbon paste electrode. The apparent diffusion coefficient of spiked p‐bromanil in paraffin oil was also determined by using the Cottrell equation. The electrocatalytic oxidation peak current of L ‐cysteic acid exhibits a linear dependency to its concentration in the ranges of 8.00×10^?6 M–6.00×10^?3 M and 5.2×10^?7 M–1.0×10^?5 M using CV and differential pulse voltammetry (DPV) methods, respectively. The detection limits (2σ) were determined as 5.00×10^?6 M and 4.00×10^?7 M by CV and DPV methods. This method was used as a new, selective, rapid, simple, precise and suitable voltammetric method for determination of L ‐cysteic acid in serum of patient's blood with migraine disease.     

Electrocatalytic Oxidation of Hydrogen Peroxide on Poly(m‐toluidine)‐Nickel Modified Carbon Paste Electrode in Alkaline Medium

The poly(m‐toluidine) film was prepared by using the repeated potential cycling technique in an acidic solution at the surface of carbon paste electrode. Then transition metal ions of Ni(II) were incorporated to the polymer by immersion of the modified electrode in a 0.2 M NiSO₄, also the electrochemical characterization of this modified electrode exhibits stable redox behavior of the Ni(III)/Ni(II) couple. The electrocatalytic ability of Ni(II)/poly(m‐toluidine)/modified carbon paste electrode (Ni/PMT/MCPE) was demonstrated by electrocatalytic oxidation of hydrogen peroxide with cyclic voltammetry and chronoamperometry methods in the alkaline solution. The effects of scan rate and hydrogen peroxide concentration on the anodic peak height of hydrogen peroxide oxidation were also investigated. The catalytic oxidation peak current showed two linear ranges with different slopes dependent on the hydrogen peroxide concentration and the lower detection limit was 6.5 μM (S/N=3). The catalytic reaction rate constant, (k_h), was calculated 5.5×10² M^?1 s^?1 by the data of chronoamperometry. This modified electrode has many advantages such as simple preparation procedure, good reproducibility and high catalytic activity toward the hydrogen peroxide oxidation. This method was also applied as a simple method for routine control and can be employed directly without any pretreatment or separation for analysis cosmetics products.     

Electrochemical Properties of the Oxo‐Manganese‐Phenanthroline Complex Immobilized on Ion‐Exchange Polymeric Film and Its Application as Biomimetic Sensor for Sulfite Ions

A biomimetic sensor containing the oxo‐bridged dinuclear manganese‐phenanthroline complex incorporated into a cation‐exchange polymeric film deposited onto glassy carbon electrode for detection of sulfite was studied. Cyclic voltammetry at the modified electrode in universal buffer showed a two electron oxidation/reduction of the couple Mn^IV(μ‐O)₂Mn^IV/Mn^III(μ‐O)₂Mn^III. The sensor exhibited electrocatalytic property toward sulfite oxidation with a decrease of the overpotential of 450 mV compared with the glassy carbon electrode. A plot of the anodic current versus the sulfite concentration for potential fixed (+0.15 V vs. SCE) at the sensor was linear in the 4.99×10^?7 to 2.49×10^?6 mol L^?1 concentration range and the concentration limit was 1.33×10^?7 mol L^?1. The mediated mechanism was derived by Michaelis? Menten kinetics. The calculated kinetics values were Michaelis? Menten rate constant= =1.33 µmol L^?1, catalytic rate constant=6.06×10^?3 s^?1 and heterogeneous electro‐chemical rate constant=3.61×10^?5 cm s^?1.     

Ruthenium(III)‐mediated oxidation of D‐mannitol by cerium(IV) in aqueous sulfuric acid medium: A kinetic and mechanistic approach

The oxidation of D ‐mannitol by cerium(IV) has been studied spectrophotometrically in aqueous sulfuric acid medium at 25°C at constant ionic strength of 1.60 mol dm^?3. A microamount of ruthenium(III) (10^?6 mol dm^?3) is sufficient to enhance the slow reaction between D ‐mannitol and cerium(IV). The oxidation products were identified by spot test, IR and GC‐MS spectra. The stoichiometry is 1:4, i.e., [D ‐mannitol]: [Ce(IV)] = 1:4. The reaction is first order in both cerium(IV) and ruthenium(III) concentrations. The order with respect to D ‐mannitol concentration varies from first order to zero order as the D ‐mannitol concentration increases. Increase in the sulfuric acid concentration decreases the reaction rate. The added sulfate and bisulfate decreases the rate of reaction. The active species of oxidant and catalyst are Ce(SO₄)₂ and [Ru(H₂O)₆]³⁺, respectively. A possible mechanism is proposed. The activation parameters are determined with respect to a slow step and reaction constants involved have been determined. © 2010 Wiley Periodicals, Inc. Int J Chem Kinet 42: 440–452, 2010     

Electrochemical Behavior and Determination of L‐Tyrosine at Single‐walled Carbon Nanotubes Modified Glassy Carbon Electrode

Based on single‐walled carbon nanotubes (SWCNTs) modified glassy carbon electrode (GCE/SWCNTs), a novel method was presented for the determination of L ‐tyrosine. The GCE/SWCNTs exhibited remarkable catalytic and enhanced effects on the oxidation of L ‐tyrosine. In 0.10 mol/L citric acid‐sodium citrate buffer solution, the oxidation potential of L ‐tyrosine shifted negatively from +1.23 V at bare GCE to +0.76 V at GCE/SWCNTs. Under the optimized experimental conditions, the linear range of the modified electrode to the concentration of L ‐tyrosine was 5.0×10^?6–2.0×10^?5 mol/L (R₁=0.9952) and 2.7×10^?5–2.6×10^?4 mol/L (R₂=0.9998) with a detection limit of 9.3×10^?8 mol/L. The kinetic parameters such as α (charge transfer coefficient) and D (diffusion coefficient) were evaluated to be 0.66, 9.82×10^?5 cm² s^?1, respectively. And the electrochemical mechanism of L ‐tyrosine was also discussed.     

Modified Carbon Paste Electrode for Kinetic Investigation and Simultaneous Determination of Ascorbic and Uric Acids

The present work explores, for the first time, the electrocatalytic oxidation of ascorbic acid (AscH₂) and its determination in the presence of uric acid (UA) on the in situ activated 4‐nitrophthalonitrile modified carbon paste electrode. The kinetic constant κ for the catalytic reaction for the electrocatalytic oxidation of ascorbic acid, evaluated by cyclic voltammetry, chronoamperometry and RDE voltammetry provided values around 10⁶ L mol^?1 s^?1. The sensor provided a linear response range for AscH₂ and UA from 5.0 up to 120.0 μmol L^?1 with detection limits of 1.6 μmol L^?1and 1.3 μmol L^?1, respectively. The sensor was applied for the simultaneous determination of AscH₂ and UA in urine samples and the average recoveries for these samples were 99.8 (±3.1)% and 99.9 (±2.1)%, respectively .     

Electrocatalytic Oxidation of Sulfite on a Cobalt Pentacyanonitrosylferrate Film Modified Glassy Carbon Electrode

The electrocatalytic oxidation of sulfite has been studied on the cobalt pentacyanonitrosylferrate modified glassy carbon electrode (CoPCNF). The CoPCNF films on the glassy carbon electrodes show an excellent electrocatalytic activity toward the oxidation of sulfite in 0.5 M KNO₃. The kinetics of the catalytic reaction was investigated by using cyclic voltammetry, rotating disk electrode (RDE) voltammetry and chronoamperometry. The average value of the rate constant, K, for the catalytic reaction and the diffusion coefficient, D, were evaluated by different approaches for sulfite and found to be 2.9×10² M^?1s^?1 and 4.6×10^?6 cm²s^?1, respectively. At a fixed potential under hydrodynamic conditions (stirred solutions), the oxidation current is proportional to the sulfite concentration and the calibration plot was linear over the concentration range 5×10^?6–1×10^?4 M. The detection limit of the method is 3×10^?6 M., low enough for the trace sulfite determination.     

Electrocatalytic Oxidation of Sulfite on a Nickel Aquapentacyanoferrate Modified Electrode: Application for Simple and Selective Determination

An electroactive metal cyanometallate complex, nickel aquapentacyanoferrate (NAPCF) was synthesized and characterized using XRD and UV‐vis spectral studies. The solid complex was then mechanically immobilized on the surface of a paraffin impregnated graphite electrode (PIGE) and the NAPCF modified electrode was characterized using cyclic voltammetry. The dependence of the modified electrode was tested in terms of supporting electrolyte, scan rate and pH of the medium. The electrocatalytic oxidation of sulfite at the modified electrode was investigated by cyclic voltammetry, hydrodynamic voltammetry and chronoamperometry techniques. It was found that the NAPCF modified electrode efficiently exhibited electrocatalytic activity for the oxidation of sulfite with relatively high sensitivity, selectivity and long life of activity. Based on the electrocatalytic oxidation, the NAPCF modified electrode was used as a sensor for the determination of sulfite. The linear working range for the determination of sulfite was 2.78×10^?6 M to 3.00×10^?3 M with a detection limit of 9.26×10^?7 M. The electrode was applied for the determination of sulfite in real samples satisfactorily.     

Fabrication of an Electrochemical L‐Cysteine Sensor Based on Graphene Nanosheets Decorated Manganese Oxide Nanocomposite Modified Glassy Carbon Electrode

The graphene nanosheets/manganese oxide nanoparticles modified glassy carbon electrode (GC/GNSs/MnOx) was simply prepared by casting a thin film of GNSs on the GC electrode surface, followed by performing electrodeposition of MnOx at applied constant potential. The GC/GNSs/MnOx modified electrode shows high catalytic activity toward oxidation of L ‐cysteine. Hydrodynamic amperometry determination of L ‐cysteine gave linear responses over a concentration range up to 120 µM with a detection limit of 75 nM and sensitivity of 27 nA µM^?1. The GC/GNSs/MnOx electrode appears to be a highly efficient platform for the development of sensitive, stable and reproducible L ‐cysteine electrochemical sensors.     

Electrocatalytic oxidation of sulfite by acetylferrocene at glassy carbon electrode

The electrochemical oxidation of sulfite catalyzed by acetylferrocene (AFc) at a glassy carbon electrode (GCE) in 0.2 M NaClO₄ aqueous solution has been studied by cyclic voltammetry. Although sulfite itself showed a sluggish electrochemical response at the GCE, the response could be enhanced greatly by using AFc as a mediator, which enables a sensitive determination of the substrate (sulfite). The reaction rate constant for catalytic oxidation was evaluated as (7.02 ± 0.05) × 10⁴ M ^?1 s^?1 by chronoamperometry. Experimental conditions that maximize the current efficiency of the electrocatalytic oxidation, such as the pH and both the catalyst (AFc) and substrate (sulfite) concentrations, were also investigated. The electrochemical kinetics of electrocatalytic oxidation of sulfite by AFc has been studied by cyclic voltammetry. In the presence of 5 × 10^?4 M AFc, the oxidation current is proportional to the sulfite concentration and the calibration plot was linear over the concentration range 2 × 10^?4–2.4 × 10^?3 M . This result can be applied in the determination of real samples. Copyright © 2005 John Wiley & Sons, Ltd.