The reactive compatibilization of NBR/EVA blends with oxazoline-modified nitrile rubber

The reactive compatibilization of ethylene-vinyl acetate copolymer (EVA)/nitrile rubber (NBR) blends has been performed using partially hydrolyzed EVA (EVALVA) in combination with oxazoline-functionalized NBR (NBROX). The synthesis of the NBROX has been performed in solution. The presence of 5 wt% of EVALVA in combination with 2.5 wt% of NBROX resulted in a substantial improvement of tensile strength of NBR/EVA (50:50 wt%) vulcanized blends, with a little increase of the elongation at break. The morphologies of these blends were examined by the scanning electron microscopy. A finer morphology has been observed in vulcanized and non-vulcanized blends, compatibilized with the co-reactive EVALVA/NBROX copolymers. Blends of NBROX/EVALVA (50:50 wt%) resulted in insoluble material, constituted by both components, as indicated by Fourier transform infrared analysis. This result indicates the reaction of the co-reactive groups (hydroxyl and oxazoline) during blending.     

Oxazoline functionalization of polyethylenes and their blends with polyamides and polyesters

The compatibilization of blends of polyamide‐6 (PA6) with linear low density polyethylene (LLDPE) and of poly(ethylene terephthalate) (PET) with high density polyethylene (HDPE), by functionalization of the polyethylenes with oxazoline groups was investigated. Chemical modification of LLDPE and HDPE was carried out by melt free radical grafting with ricinoloxazoline maleinate. Blends preparation was made either with a two‐steps procedure comprising functionalization and blending, and in a single step in which the chemical modification of polyethylene with the oxazoline monomer was realized in situ, during blending. The characterization of the products was carried out by FTIR spectroscopy and scanning electron microscopy (SEM). The rheological and mechanical properties of the blends were also investigated. The results show that functionalization of the polyethylenes can be achieved by melt blending with ricinoloxazoline maleinate even in the absence of free radical initiators. The compatibilization of the blends enhances the dispersion of the minor phase significantly, increases the melt viscosity, and improves the mechanical properties. The one‐step preparation of the compatibilized blends was also found to be effective, and is thought to be even more promising in view of commercial application.     

On the modification of the nitrile groups of acrylonitrile/butadiene/styrene into oxazoline in the melt

Oxazoline functionality is well known to be highly reactive toward a lot of other functional groups like carboxyls, hydroxyls, mercaptans, and amines. In this work we report the possibility to modify the nitrile groups of an acrylonitrile/butadiene/styrene (ABS) copolymer into oxazoline in the molten state in the presence of aminoethanol as modifier agent and zinc acetate as a catalyst. The reaction has been carried out in a batch mixer and in a corotating twin screw extruder. The conversion of the nitrile groups into oxazoline has been verified by infrared spectroscopy, NMR analysis microanalysis and confirmed by thermomechanical characterization. The results indicate that the kinetic of grafting is fast and the conversion of the nitrile groups into oxazoline relatively high, encouraging the use of this modified polymer in the reactive compatibilization of ABS‐based blends. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1795–1802, 2000     

增容聚苯乙烯共混物的研究进展

综述了增容聚苯乙烯与聚乙烯、聚丙烯、聚酰胺共混物的研究进展。不同共混物采用不同的增容剂,可使增容聚苯乙烯共混物改善分散相尺寸、界面相互作用与粘结,达到提高共混物的力学性能的目的。增容效果与增容剂的类型、用量和分子结构有关。     

Microhardness and thermal stability of compatibilized LDPE/PA6 blends

Microhardness tests, water absorption and thermogravimetric measurements have been performed on blends of low density polyethylene (LDPE) with different molar mass and polyamide 6 (PA6) compatibilized with 2 pph poly(ethylene-co-acrylic acid) (Escor 5001 by Exxon). The negative deviation of Vickers microhardness from the additivity has been interpreted by changes in the crystallinity of the blend components. The hardness values of the compatibilized blends that are lower than those of the corresponding uncompatibilized blends have been explained by the decrease of the degree of crystallinity of PA6 phase in the presence of Escor. The molar mass of LDPE almost does not influence on the hardness values. The lower water absorption of the compatibilized blends, caused by the formation of a copolymer between PA6 and the compatibilizer leads to microhardness values of the wet compatibilized blends higher than those of the corresponding uncompatibilized blends. The thermogravimetric measurements demonstrate that the thermal stability of blends increases in the presence of 2 pph Escor 5001. The results confirm the compatibilizing efficiency of Escor 5001 towards LDPE/PA6 blends in a wide composition range.     

RPS／CPE的反应性共混及其对PS／PE的增容作用

用ＦＴＩＲ、ＤＳＣ等方法研究了含恶唑啉官能力的聚苯乙烯（ＲＰＳ）与氯化聚乙烯（ＣＰＥ）之间的反应。ＲＰＳ、ＣＰＥ、ＰＳ、ＰＥ在不同温度下用反应式挤出要熔融共辊，结果表明，ＲＰＳ／ＣＰＥ对ＰＳ／ＰＥ共混物具有增容作用，提高了共混物的力学性能。此反应性共混适宜在较低温度下进行，对ＲＰＳＣＰＥ共混物还进行了动态力学表征，并与ＲＰＳ进行比较以进一步了解共混物的特征。     

Compatibilization of elastomer-based blends

The reactive compatibilization of ethylene-propylene-diene (EPDM)-based dissimilar elastomer blends has been investigated in terms of mechanical properties and swelling degree. The use of mercapto-functionalized copolymers resulted in an improvement of mechanical properties of natural rubber-EPDM blends. The mercapto-groups are able to react with the carbon-carbon double bonds of the high diene rubber, resulting in a good interaction between phases. These interactions were confirmed by the amount of insoluble material obtained in non-vulcanized blends. From dynamic mechanical properties and swelling degree, one can suggest a covulcanization process in these blends cured with sulfur-based system. Blends composed by nitrile rubber with EPDM displayed good results in terms of mechanical properties when mercapto-functionalized EVA was employed instead of functionalized EPDM, probably because of the higher polarity of the former associated to its lower viscosity. Additionally, an improvement on mechanical properties was also achieved by using EPDM functionalized with mercapto or anhydride groups in combination with nitrile rubber functionalized with epoxy or oxazoline groups.     

PA66/PA12/clay based nanocomposites: structure and thermal properties

In a previous paper the structure and the physical properties of melt mixed polyamide 66 (PA66)/polyamide 12 (PA12) blends characterized by different compositions have been investigated by means of morphological and physical analyses. A low amount of organically‐modified layered silicate (OMLS, 4 wt%) was introduced in order to evaluate its effect on blends structure and components miscibility. This paper completes the characterization of these materials investigating their thermal properties by means of standard and modulated differential scanning calorimetry (DSC, MDSC), dynamic‐mechanical analysis (DMA), and thermogravimetric analysis (TGA). The partial miscibility of PA66 and PA12, with phase separation depending on blend composition, has been confirmed by analyzing the glass transition temperature (T_g) dependence on composition as well as the existence of strong segmental interactions between polymer components. A compatibilizing action of OMLS has been observed because of a lowering of interfacial tension avoiding coalescence phenomena between particles during melt mixing process. Copyright © 2010 John Wiley & Sons, Ltd.     

Melt rheology and morphology of thermoplastic elastomers from polyethylene/nitrile‐rubber blends: The effect of blend ratio,reactive compatibilization,and dynamic vulcanization

A study of the melt‐rheological behavior of thermoplastic elastomers from high‐density polyethylene and acrylonitrile butadiene rubber (NBR) blends was carried out in a capillary rheometer. The effect of the blend ratio and shear rate on the melt viscosity reveals that the viscosity decreases with the shear rate but increases with NBR content. Compatibilization by maleic anhydride modified polyethylene has no significant effect on the blend viscosity, but a finer dispersion of the rubber is obtained, as is evident from scanning electron micrographs. The melt‐elasticity parameters, such as the die swell, principal normal stress difference, recoverable shear strain, and elastic shear modulus of the blends, were also evaluated. The effect of annealing on the morphology of the extrudate reveals that annealing in the extruder barrel results in the coalescence of rubber particles in the case of the incompatible blends, whereas the tendency toward agglomeration is somewhat suppressed in the compatibilized blends. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1104–1122, 2000     

剪切作用下马来酸酐接枝乙烯-辛烯共聚物和乙烯-丙烯酸丁酯-甲基丙烯酸缩水甘油酯共聚物对PA1010/PP共混物的增容作用比较

采用熔体共混的方法制备了两种增容剂增容的聚酰胺1010/聚丙烯(PA1010/PP)共混物,通过扫描电镜(SEM)、力学性能和差示扫描量热(DSC)测试,对动态保压注射成型(动态)和普通注射成型(静态)中增容剂POE-g-MAH(马来酸酐接枝乙烯-辛烯共聚物)和PTW(乙烯-丙烯酸丁酯-甲基丙烯酸缩水甘油酯共聚物)对PA1010/PP共混物的增容作用进行了比较研究.研究结果表明,普通注射成型中,PTW增容体系具有更小的分散相粒子,在DSC测试中出现两个结晶峰,即出现异相成核结晶和均相成核结晶,具有更好的拉伸和冲击性能,增容作用更佳.动态保压注射成型中施加剪切可以提高所有共混物的拉伸强度、拉伸模量和缺口冲击强度,PTW和POE-g-MAH两种增容剂增容体系冲击性能相近,但POE-g-MAH增容体系的分散相相区尺寸减小明显、分布均匀性显著增加,材料冲击强度增加幅度更大,表明剪切更有利于POE-g-MAH增容作用的进行.两种增容剂增容作用的不同源于它们化学组成的不同引起的材料形态差别.     

Improving properties of natural rubber/polyamide 12 blends through grafting of diacetone acrylamide functional group

The aim of the present study was to improve the compatibility in blends of natural rubber (NR) and polyamide 12 (PA12) by grafting NR with hydrophilic monomer, diacetone acrylamide (DAAM), via seeded emulsion polymerization. The increase in polarity of NR after grafting modification was confirmed by a considerable increase in the polar component of its surface energy. Blends of graft copolymers of NR and poly(diacetone acrylamide) prepared using 10 wt% of DAAM (NR‐g‐PDAAM10) and PA12 were prepared at a 60/40 blend ratio (wt%) using simple blend and dynamic vulcanization techniques. The mechanical and rheological properties of the resulting blends were subsequently investigated and compared with those of the corresponding blends based on unmodified NR. The results show that dynamic vulcanization led to a significant increase in both mechanical and rheological properties of the blends. It was also observed that the dynamically cured NR‐g‐PDAAM10/PA12 blend had smaller particle size of vulcanized rubber dispersed in the PA12 matrix than observed for the dynamically cured NR/PA12 blend. This is due to the compatibilizing effect of DAAM groups present in NR‐g‐PDAAM10 molecule, which decreases the interfacial tension between the two polymeric phases. Therefore, it can be stated that the interfacial adhesion between NR and PA12 was improved by the presence of DAAM groups in NR molecule. This was reflected in the higher tensile properties observed in the dynamically cured NR‐g‐PDAAM10/PA12 blend. Copyright © 2017 John Wiley & Sons, Ltd.     

Effect of maleic anhydride-grafted ethylene-propylene rubber on the mechanical, rheological and morphological properties of organoclay reinforced polyamide 6/polypropylene nanocomposites

Polyamide 6/polypropylene (PA6/PP = 70/30 parts) blends containing 4 phr (parts per hundred resin) of organophilic modified montmorillonite (organoclay) were compatibilized with maleic anhydride-grafted ethylene-propylene rubber (EPRgMA). The blends were melt compounded in twin screw extruder followed by injection molding. The mechanical properties of PA6/PP nanocomposites were studied by tensile and flexural tests. The microstructure of the nanocomposite were assessed by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD). The dynamic mechanical properties of the PA6/PP blend-based nanocomposites were analyzed by using a dynamic mechanical thermal analyzer (DMTA). The rheological properties were conducted from plate/plate rheometry via dynamic frequency sweep scans. The melt viscosity in a high shear rate region was performed by using a capillary rheometer. The strength and stiffness of the PA6/PP-based nanocomposites were improved significantly with the incorporation of EPRgMA. Adding EPRgMA to the PA6/PP blends resulted in a finer dispersion of the PP phase. TEM and XRD results revealed that the organoclay was dispersed more homogeneously in the presence of EPRgMA, however, mostly in the PA6 phase of the blends. DMTA results showed that EPRgMA worked as an effective compatibilizer. The storage (G′) and loss moduli (G″) assessed by plate/plate rheometry of PA6/PP blends increased with the incorporation of EPRgMA and organoclay. Furthermore, the apparent shear viscosity of the PA6/PP blend increased significantly for the EPRgMA compatibilized PA6/PP/organoclay nanocomposite. This was traced to the formation of an interphase between PA6 and PP (via PA6-g-EPR) and effective intercalation/exfoliation of the organoclay.     

Quantitative characterization of toughening mechanisms of rubber modified polymers

The volume changes of rubber modified polymers under creep at room temperature were successfully used to characterize the toughening mechanisms of blends with brittle polymer matrices such as high impact polystyrene.This approach cannot be applied to pseudo-ductile polymers such as polypropylene and polyamide,because they are ductile when stretched at low speed at room temperature.Based on the time-temperature equivalence princi ple,the volume change at low temperature is proposed to characterize quantitatively the toughening mechanisms of polymer blends with ductile matrices,which is illustrated by applying this approach to rubber modified polypropylene     

Creation of crosslinkable interphases in polymer blends

A new type of bi- and trifunctional coupling agents containing 2-oxazoline and/or 2-oxazinone as well as hydrosilane moieties has been prepared by hydrosilylation of the corresponding allyl ether containing precursors with poly(methylhydro)siloxanes. In heterogeneous model blends based on mono-carboxylic acid terminated polystyrene (PS) and mono-amine terminated polyamide 12 (PA), the oxazoline and oxazinone units can selectively react with the carboxylic groups or amino groups, respectively. Under this mixing conditions the hydrosilane partially crosslinks. The morphology development of the three-component blends under melt mixing conditions is a rather complex process. We have shown that the coupling agents are immiscible with the polymers and form their own phase. Under proper processing conditions they locate at least partially at the PS/PA interface and can be used for further modification of the blend interphase, e.g. for crosslinking by hydrolysis. This crosslinking can be accelerated by the addition of a Pt-catalyst during the melt mixing.     

Viscoelastic behavior of polypropylene/nitrile rubber thermoplastic elastomer blends: Application of Kerner's models for reactively compatibilized and dynamically vulcanized systems

The viscoelastic properties of binary blends of nitrile rubber (NBR) and isotactic polypropylene (PP) of different compositions have been calculated with mean‐field theories developed by Kerner. The phase morphology and geometry have been assumed, and experimental data for the component polymers over a wide temperature range have been used. Hashin's elastic–viscoelastic analogy principle is used in applying Kerner's theory of elastic systems for viscoelastic materials, namely, polymer blends. The two theoretical models used are the discrete particle model (which assumes one component as dispersed inclusions in the matrix of the other) and the polyaggregate model (in which no matrix phase but a cocontinuous structure of the two is postulated). A solution method for the coupled equations of the polyaggregate model, considering Poisson's ratio as a complex parameter, is deduced. The viscoelastic properties are determined in terms of the small‐strain dynamic storage modulus and loss tangent with a Rheovibron DDV viscoelastometer for the blends and the component polymers. Theoretical calculations are compared with the experimental small‐strain dynamic mechanical properties of the blends and their morphological characterizations. Predictions are also compared with the experimental mechanical properties of compatibilized and dynamically cured 70/30 PP/NBR blends. The results computed with the discrete particle model with PP as the matrix compare well with the experimental results for 30/70, 70/30, and 50/50 PP/NBR blends. For 70/30 and 50/50 blends, these predictions are supported by scanning electron microscopy (SEM) investigations. However, for 30/70 blends, the predictions are not in agreement with SEM results, which reveal a cocontinuous blend of the two. Predictions of the discrete particle model are poor with NBR as the matrix for all three volume fractions. A closer agreement of the predicted results for a 70/30 PP/NBR blend and the properties of a 1% maleic anhydride modified PP or 3% phenolic‐modified PP compatibilized 70/30 PP/NBR blend in the lower temperature zone has been observed. This may be explained by improved interfacial adhesion and stable phase morphology. A mixed‐cure dynamically vulcanized system gave a better agreement with the predictions with PP as the matrix than the peroxide, sulfur, and unvulcanized systems. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1417–1432, 2004     

Radiation induced graft copolymerization of acrylonitrile on natural rubber

Acrylonitrile graft natural rubber was prepared by initiating the polymerization of acrylonitrile in natural rubber field latex using γ-rays. The reaction was carried out at different rubber-monomer concentrations and the properties of the modified rubbers were compared with those of natural rubber and nitrile rubber.     

Ultra‐high molecular weight styrenic block copolymer/TPU blends for automotive applications: Influence of various compatibilizers

Thermoplastic elastomers (TPEs) based on new generation ultrahigh molecular weight styrene‐ethylene‐butylene‐styrene (SEBS) and thermoplastic polyurethane (TPU) are developed and characterized especially for automotive applications. Influence of maleic anhydride grafted styrene‐ethylene‐butylene‐styrene (SEBS‐g‐MA) and maleic anhydride grafted ethylene propylene rubber (EPM‐g‐MA) as compatibilizers has been explored and compared on the blends of SEBS/TPU (60:40). The amount of compatibilizers was varied from 0 to 10 phr. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) studies revealed the dramatic changes from a nonuniform to finer and uniform dispersed phase morphology. This was reflected in various mechanical properties. SEBS‐g‐MA modified blends showed higher tensile strength. EPM‐g‐MA modified blends also displayed considerable improvement. Elongation at break (EB) was doubled for the entire compatibilized blends. Fourier‐transform infrared spectrometry (FTIR) confirmed the chemical changes in the blends brought about by the interactions between blend components and compatibilizers. Both SEBS‐g‐MA and EPM‐g‐MA had more or less similar effects in dynamic mechanical properties of the blends. Additionally, melt rheological studies have also been pursued through a rubber process analyzer (RPA) to get a better insight.     

Deformation of thermotropic liquid crystalline polymer droplets dispersed in a polyamide

The deformation of dispersed droplets of a thermotropic liquid crystalline polymer in a polyamide (nylon 6) matrix was studied by morphological observation. An immiscible binary blend and compatibilized ternary blends were studied. For the uncompatibilized blend, the morphology of the blends was that of a typical immiscible blend showing poor adhesion and no deformation of the dispersed phase. For the compatibilized blend, deformation of the dispersed TLCP phase was observed even if the viscosity of the matrix was lower than that of the TLCP phase. Compatibilizer addition improved the interfacial adhesion, hence enabled TLCP droplets to be deformed. A simple mechanism for the deformation of TLCP droplets was presented considering characteristic rheological properties of the TLCP melt.     

Amide-exchange reactions in mixtures of N-alkyl amides and in polyamide melt blends

The amide-exchange reactions which cause copolymer formation in polyamide melt blends were studied with mixtures of N-ethylcaproamide and N-hexylacetamide containing small concentrations of caproic acid and hexylamine as a model system for melt blends of aliphatic polyamides. Amide exchange was found to involve acidolysis and aminolysis reactions with no detectable contribution of direct reaction between amide groups. Kinetics data are consistent with formation of an anhydride intermediate in amide acidolysis. Rate constants over the range 200–275°C and activation energies for amide acidolysis and aminolysis reactions are given. Equations are given for calculating amide exchange rates in polyamide melt blends and for relating degree of amide exchange to block copolymer composition.     

Preparation and properties of PP/PC/POE blends

In order to develop PP (polypropylene)‐based blends with balanced toughness and rigidity, the poly‐blends of PP/PC (polycarbonate)/POE (ethylene–octene copolymer) were prepared by applying styrene–ethylene–propylene–styrene (SEPS) as the macromolecular compatibilizer. The compatibilizing effect was studied in terms of the mechanical, morphologies and thermal properties, and the compatibilized PP‐based blends presented remarkable improvement in impact toughness and balanced tensile strength due to the formed special morphology structure. Additionally, by preparing the pre‐blend of PC/SEPS, the melt viscosity of the PP matrix can match that of the dispersed phase PC and POE, which led to a further improvement in the mechanical property of the blends. Copyright © 2009 John Wiley & Sons, Ltd.