Effect of fluoride and hydroxyl group on bioactivity of the anodized films prepared by two-step anodization at low current density

Titanium and its alloys are promising dental implant materials. In order to improve the bioactivity of the anodized films, the two-step anodization was performed to produce the films. The steps were performed at 0.2 mA/cm² for 30 min in electrolytes containing H₃PO₄/C₂H₅OH and H₃PO₄/C₂H₅OH/NH₄F, respectively. The anodized films were soaked in a simulated body fluid (SBF). The effects of surface roughness, hydroxyl groups, fluoride, and hydrophilicity groups on the bioactivity were investigated and were found on the anodized films formed under two-step anodization using 1 M H₃PO₄ + 80% V/V C₂H₅OH + 0.75 wt% NH₄F. The bioactivity evaluation showed that the combination of two-step anodization in NH₄F as an electrolyte induced a formation of apatite on the anodized films. The surface roughness, hydroxyl groups, and fluoride formed on the hydrophilic anodized films are found to be responsible for the rapid formation of hydroxyapatite during SBF soaking. This will be useful in various biomedical applications especially in dental implant procedures.     

钛、铝和玻璃上TiO2光催化膜的失活研究

采用浸渍提拉法，在平行条件下制备了钛、铝和玻璃载体上的TiO₂膜TiO₂ / Ti、TiO₂ / Al和TiO₂ / G，利用X射线光电子能谱(XPS)、原子力显微镜(AFM)和光催化降解实验等手段对膜样品进行了表征和活性评价。实验结果表明，在铝和玻璃基材上制膜时发生了显著的基材元素溢出，使各膜样品的化学组成不同，同时TiO₂粒子和膜表面形貌也因前驱物烧结行为不同而差异较大。TiO_{2相似文献}   

Effect of the anodization voltage on the dimensions and photoactivity of titania nanotubes arrays

This work compares the behaviors of TiO₂ nanotube (TNTs) array obtained by anodization of Ti foils in an ethylene glycol/NH₄F/water electrolyte with different applied voltages during a constant anodization time, and for the same electrolyte composition. The crystal structure and surface morphology of the annealed anodic films are investigated by X‐Ray diffraction system, Raman spectroscopy and scanning electron microscopy, respectively. The TiO₂ nanotubes obtained at potentials of 20–40–60 V show different inner diameters (42–89–124 nm), tube length (1.2–3.3–12.7 µm) and wall thicknesses (12–15–18 nm). The influence of these geometric parameters on the photoelectrochemical properties and the photocatalytic activity were investigated in detail. The results showed that the photocatalytic performances of TNT films are improved when the specific surface, the tube length and the solid fraction are increased, but the increase is slowed down when a limiting thickness of the layer is reached. The surface states which usually show high density in nanostructured layers do not seem to influence significantly the photocatalytic activity of the layers. Copyright © 2013 John Wiley & Sons, Ltd.     

Fabrication of self-organized TiO2 nanotubes from columnar titanium thin films sputtered on semiconductor surfaces

Self-organized nanotube arrays of TiO₂ have been grown from titanium (Ti) thin films deposited on p-type Si(1 0 0) substrates. Structural and morphological characterizations carried out by X-ray diffraction and scanning electron microcopy indicate that the sputtered crystalline Ti thin films used for subsequent anodization are hexagonally closed packed (hcp-Ti) and show a columnar morphology. Electrochemical anodization of the Ti films was carried out by potentiostatic experiments in 1 M H₃PO₄ + 1 M NaOH + 0.5 wt% HF electrolyte at room temperature. The TiO₂ nanotubes on a semiconductor substrate have an average tube length of approximately 560 nm, diameter in the order of 80 nm and wall thickness approximately 20 nm.     

Photocatalytic Oxidation of Aniline in the Gas Phase Using Porous TiO2 Thin Films

The gas-phase photocatalytic oxidation of aniline on a new kind of porous nano-TiO₂ composite films is investigated. The composite film was prepared on glass fiber with the water glass as binders and dilute H₂SO₄ solution as solidifying reagent. The surface characters were observed by scanning electron microscope. The photocatalytic degradation of aniline on the composite films was carried out in a TiO₂/UV system. Some important factors affecting the photodegradation, such as the concentration of TiO₂, the initial concentration of aniline, and the existing water vapor, are also studied. The product of photocatalytic oxidation was detected by Fourier transform-Infrared. The partial intermediate products were absorbed on TiO₂ surface, which resulted in catalyst deactivation. But when it was irradiated under UV illumination or solar irradiation for some time, the catalyst could be reused without loss of catalytic activity. Translated from the Journal of Wuhan University (Natural Science Edition), 2005, 51(2) (in Chinese)     

含氯离子电解液中二氧化钛纳米管的阳极氧化形成机理及应用

采用电化学阳极氧化的方法,以氯化铵(NH₄Cl)水溶液为电解液,在纯钛表面制备了二氧化钛(TiO₂)纳米管。考察了制备电压、氧化时间、Cl^-浓度和钛基体的退火处理对阳极氧化过程的影响规律,探讨了在含氯离子电解液中纳米管的形成机理,并基于上述含氯离子电解液中纳米管形成机制,通过两步阳极氧化法得到无支撑纳米管薄膜。     

RE/TiO2光催化剂的谱学特性与气相光催化性能的研究

采用改进的sol-gel法和浸渍法制备了TiO₂掺杂稀土离子La³⁺、Y³⁺、Gd³⁺、Er³⁺、Nd³⁺、Pr³⁺的RE/TiO₂光催化剂,运用FTIR、XRD、TEM、低温氮吸附/脱附、TG/DTA、UV-Vis DRS、表面光电压谱(SPS)等进行表征,以气相光催化降解乙烯、溴代甲烷作为探针反应,阐明了RE/TiO₂光催化剂的谱学特性与气相光催化性能的关系。结果显示,稀土离子掺杂后,TiO₂的锐钛矿含量增加,比表面积增大,粒径变小,吸收边发生蓝移,表面光电压的响应阈值增大,此外,Pr³⁺除外的其它稀土离子掺杂的TiO₂的表面光电压信号增强;光催化降解实验表明,与纯TiO₂相比,La³⁺、Y³⁺、Gd³⁺、Er³⁺、Nd³⁺掺杂TiO₂样品上乙烯、溴代甲烷的光催化活性均有不同程度的增强,而且表现出较强的矿化能力。但是,掺杂Pr³⁺的TiO₂的光催化性能降低恰好对应较弱的表面光电压信号。所以,本文认为提高光生电子-空穴对的分离效率是改善光催化性能的关键因素。     

阳极氧化法制备二氧化钛纳米管及其荧光性质

室温下采用电化学阳极氧化法在NaF、Na₂SO₄和H₂SO₄的混合溶液中用化学处理后的纯Ti片表面组装了一层结构高度有序的高密度TiO₂纳米管阵列。考察了几种主要的实验参数(阳极氧化电压、温度、电解液浓度)对TiO₂纳米管阵列形貌和尺寸的影响，探讨了二次阳极氧化对纳米管形貌的改善。对TiO₂纳米管阵列进行扫描电子显微镜(SEM)和荧光(PL)分析，探讨其生长机理。结果表明，孔径随阳极氧化电压的升高而变大，温度、电解液浓度影响反应过程中电流密度的大小；二次阳极氧化得到的纳米管的有序性有所改善，孔径大小更为均一，并且发现TiO₂纳米管的荧光具有量子效应。     

Preparation and characterization of Zr doped TiO2 nanotube arrays on the titanium sheet and their enhanced photocatalytic activity

This paper described a new method for the preparation of Zr doped TiO₂ nanotube arrays by electrochemical method. TiO₂ nanotube arrays were prepared by anodization with titanium anode and platinum cathode. Afterwards, the formed TiO₂ nanotube arrays and Pt were used as cathode and anode, respectively, for preparation of Zr/TiO₂ nanotube arrays in the electrolyte of 0.1 M Zr(NO₃)₄ with different voltage and post-calcination process. The nanotube arrays were characterized by field-emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), X-ray photoelectron spectra (XPS) and UV-Vis diffusion reflection spectra (DRS). The photocatalytic activities of these nanotubes were investigated with Rhodamine B as the model pollutant and the results demonstrated that the photocatalytic efficiency of Zr doped TiO₂ nanotubes was much better than that of TiO₂ nanotubes under UV irradiation. Zr/TiO₂ nanotube arrays doped at 7 V and calcined at 600 °C (denoted as TiO₂-7 V-600) achieved the best photocatalytic efficiency and the most optimal doping ratio was 0.047 (Zr/Ti). TiO₂-7 V-600 could be reused for more than 20 times and maintained good photocatalytic activities.     

Effect of dopant concentration on photocatalytic activity of TiO2 film doped by Mn non-uniformly

The thin films of TiO₂ doped by Mn non-uniformly were prepared by sol-gel method under process control. In our preceding study, we investigated in detail, the effect of doping mode on the photocatalytic activity of TiO₂ films showing that Mn non-uniform doping can greatly enhance the activity. In this study we looked at the effect of doping concentration on the photocatalytic activity of the TiO₂ films. In this paper, the thin films were characterized by UV-vis spectrophotometer and electrochemical workstation. The activity of the photocatalyst was also evaluated by photocatalytic degradation rate of aqueous methyl orange under UV radiation. The results illustrate that the TiO₂ thin film doped by Mn non-uniformly at the optimal dopant concentration (0.7 at %) is of the highest activity, and on the contrary, the activity of those doped uniformly is decreased. As a comparison, in 80 min, the degradation rate of methyl orange is 62 %, 12 % and 34 % for Mn non-uniform doping film (0.7 at %), the uniform doping film (0.7 at %) and pure titanium dioxide film, respectively. We have seen that, for the doping and the pure TiO₂ films, the stronger signals of open circuit potential and transient photocurrent, the better photocatalytic activity. We also discusse the effect of dopant concentration on the photocatalytic activity of the TiO₂ films in terms of effective separation of the photon-generated carriers in the semiconductor.     

Effect of surface finishing on the formation of nanostructure and corrosion behavior of Ni–Ti alloy

In the present work, we have investigated the formation of nanostructured oxide layers by anodic oxidation on different surface finished (mirror finished, 600 and 400 grit polished) nickel–titanium alloy (Ni–Ti) in electrolyte solution containing ethylene glycol and NH₄F_. The anodized surface has been characterized by field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS) and X‐ray photoelectron spectroscopy (XPS). The corrosion behaviors of the Ni–Ti substrate and anodized samples have been investigated by electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization in simulated body fluid (Hanks' solution). The results show that the native oxide on the substrate is replaced by nanostructures through anodization process. XPS of Ni–Ti substrate shows the presence of Ni⁰, NiO, Ti⁰ and TiO₂ species, whereas Ni₂O₃ and Ni(OH)₂ and TiO₂ are observed in the samples after anodization. Corrosion resistance of the anodized sample is comparable with that of the untreated sample. Copyright © 2016 John Wiley & Sons, Ltd.     

超临界流体干燥法制备纳米TiO2-SnO2-SiO2复合光催化剂及其光催化性能研究

半导体多相光催化法作为一种污染治理新技术越来越受到人们的重视,在所使用的半导体光催化剂中,TiO2以无毒,催化活性高,价廉,无污染等特点,成为最具有前途的绿色环保型催化剂之一[1],但其自身具有局限性,如禁带宽度大,需在近紫外光下才能激发产生电子空穴对,对太阳光的利用率仅     

Ni控制掺杂TiO2薄膜的光电化学及光催化活性

采用溶胶-凝胶法通过分步控制工艺制备了镍离子不同掺杂方式的TiO₂薄膜。通过甲基橙的光催化降解动力学来表征其光催化活性。结果表明：镍离子非均匀掺杂在掺杂量0.5%时可以明显增强TiO₂的光催化活性，而均匀掺杂提高TiO₂的光催化活性较小。光电化学表征结果显示：镍离子非均匀掺杂TiO₂薄膜的瞬时光电流信号较强，说明其光生载流子易于生成且分离效果较好；循环伏安曲线表明，光照时Ni非均匀掺杂的TiO₂薄膜改变了体系的氧化还原电位，说明了薄膜内建电场的建立。基于半导体的P-N结原理探讨了镍离子非均匀掺杂TiO₂薄膜的光催化活性机理。     

Controllable synthesis of well-ordered TiO2 nanotubes in a mixed organic electrolyte for high-efficiency photocatalysis

Well-ordered TiO 2 nanotube arrays (TNAs) were fabricated by electrochemical anodization in a mixed organic electrolyte consisting of ethylene glycol and glycerol. The morphology, structure, crystalline phase, and photocatalytic properties of TNAs were characterized by using TEM, SEM, XRD and photodegradation of methylene blue. It was found that the morphology and structure of TNAs could be significantly influenced by the anodization time and applied voltage. The obtained tube length was found to be proportional to anodization time, and the calculated growth rate of nanotubes was 0.6 m/h. The microstructure analysis demonstrated that the diameter and thickness of the nanotubes increased with the increase of anodization voltage. The growth mechanism of TNAs was also proposed according to the observed relationship between current density and time during anodization. As expected, the obtained TNAs showed a higher photocatalytic activity than the commercial TiO 2 P25 nanoparticles.     

Preparation and Characterization of TiO2 Nanotube Arrays via Anodization of Titanium Films Deposited on FTO Conducting Glass at Room Temperature

Self-organized TiO₂ nanotube arrays with micro-scale length were prepared on fluorine-doped tin oxide (FTO) conducting glass in NH₄F/glycerol electrolyte by electrochemical anodization of pure titanium films deposited by radio frequency magnetron sputtering (RFMS) at room temperature. The samples were characterized by means of field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), and photoelectrochemistry methods. The results showed that Ti films prepared at the condition of Ar pressure 0.5 Pa, power 150 W, and 0.5 h at room temperature possessed the zone T model structure with good homogeneity and high denseness. When the anodization time was prolonged from 1 to 3 h at the voltage of 30 V, the pore diameter of TiO₂ nanotubes increased from 50 to 75 nm, and the length increased from 750 to 1100 nm and then gradually decreased to 800 nm, while their wall morphology changed from smooth to rough. Also with increasing the anodization voltage, the pore diameter became larger, and the remaining oxide layer reduced, which could be easily removed by ultrasonic-chemical cleaning in 0.05% (w, mass fraction) diluted HF solution. Moreover, the photocurrent response curves and electrochemical impedance spectroscopy (EIS) results indicated that UV-illumination clearly enhanced the effective separation of the electron-hole pairs and the crystallized electrodes from the annealing treatment of as-anodized electrodes at 450 °C exhibited a better photoelectrochemical performance.     

Surface properties and photocatalytic activity of nanocrystalline titania films

In this work the efficiency and physicochemical details of a thin film produced by help of a microwave assisted sol gel technique is compared to different commercial powders (Degussa P25 and Hombikat UV100) deposited on glass substrates. Furthermore, a supercritical produced TiO₂ powder (SC 134) was included in the comparison.The prepared TiO₂ films were characterized using XRD, XPS, AFM, DSC and DLS. The photocatalytic activity was determined using stearic acid as a model compound. Investigation of the prepared films showed that the Degussa P25 film and the sol–gel film were the most photocatalytic active films. The activity of the films was found to be related to the crystallinity of the TiO₂ film and the amount of surface area and surface hydroxyl groups. Based on the XPS investigation of the films before and after UV irradiation it was suggested that the photocatalytic destruction of organic matter on TiO₂ films proceeds partly through formation of hydroxyl radicals which are formed from surface hydroxyl groups created by interactions between adsorbed water and vacancies on the TiO₂ surface. Furthermore a correlation between the amount of OH groups on the surface of the different TiO₂ films and the photocatalytic activity was found.     

Fabrication of self-organized TiO2 nanotube arrays for photocatalytic reduction of CO2

The photocatalytic conversion of CO₂ and H₂O to alcohols was achieved using self-organized TiO₂ nanotube arrays (TNAs), which were prepared by electrochemical anodization of Ti foils in 1 M (NH₄)₂SO₄ electrolyte containing 0.5 wt% NH₄F. Experimental results revealed that the morphology and structure of self-organized TNAs could be strongly influenced by the applied voltage and anodization temperature, and the optimized TNAs were prepared by electrochemical anodization of Ti foils under optimal conditions (i.e., at 20 V for 2 h at 30 °C). The as-prepared TNAs were amorphous and could be transformed to anatase phase during the thermal treatment at 450 °C in air for 3 h. By using the annealed TNAs as a photocatalyst, the photocatalytic reduction of CO₂ to alcohol, predominately methanol and ethanol, was demonstrated under Xenon lamp illumination. Based on the photocatalytic measurements, the production rates of methanol and ethanol were calculated to be ～10 and ～9 nmol cm^?2 h^?1, respectively. In addition, the formation mechanism of methanol and ethanol was also tentatively proposed.     

B离子掺杂TiO2催化剂(TiO2－xBx)光催化活性的研究

采用溶胶-凝胶法制备出纳米TiO₂和TiO_2－xB_x催化剂. 光催化实验证明, TiO_2－xB_x催化剂的紫外、可见光催化活性均高于TiO₂. XRD, XPS和Raman结果表明, B离子是以取代式掺杂占据了TiO₂的O^2－的晶格位置. UV-Vis和PL谱的结果表明, B离子的2p轨道与O的2p轨道形成混合价带, 产生可见光响应, B离子的掺入有效地阻止了光生载流子的复合, 促进了其分离, 是TiO_2－xB_x催化剂紫外、可见光催化活性提高的主要原因.     

High photocatalytic activity and stability for decomposition of gaseous acetaldehyde on TiO2/Al2O3 composite films coated on foam nickel substrates by sol-gel processes

A set of anatase titanium dioxide (TiO₂) films coated on foam nickel that modified by Al₂O₃ films as transition layer (indicated as TiO₂/Al₂O₃ films) were synthesized via sol-gel route. The bulk and surface properties of the TiO₂/Al₂O₃ films were characterized by thermal gravimetric and differential scanning calorimetry (TG-DSC), X-ray diffraction (XRD), field-emission scanning electron microscope (FE-SEM), and BET. The photocatalytic activities of TiO₂/Al₂O₃ films were investigated based on the degradation of gaseous acetaldehyde under ultraviolet (UV) irradiation. The foam nickel is a promising substrate material in practical applications because of its excellent hydrodynamic properties for gas passing. The TiO₂/Al₂O₃ composite films showed much higher photocatalytic activity and stability for degradation of gaseous acetaldehyde than the onefold TiO₂ films. The significant enhancement in photocatalytic activity and stability can be ascribed to the coating of Al₂O₃ transition layer, which concentrates the target substances around TiO₂ particles and increases the specific surface area (SSA) of the substrate (the SSAs of bare foam nickel and Al₂O₃ modified foam nickel are 0.12 and 113.7 m²/g, respectively) to provide more sites for TiO₂ loading.     

钛基TiO2纳米管阵列电极的光电催化性能

应用电化学阳极氧化法在纯Ti基底上制备高度有序的TiO2纳米管阵列,考察了Ti/TiO2光阳极的光电化学响应.以苯酚溶液为目标污染物,研究Ti/TiO2电极的光电催化性能,并与光催化性能进行比较.结果表明,该电极光电催化性能优于光催化性能.施加0.6 V电压时,光电催化性能最好.电化学阻抗谱分析显示,光电催化和光催化降解过程的速控步骤均为表面反应步骤,外加偏压减小了界面电荷转移阻抗,提高了光生载流子的分离效率.