马来酸酐与乙酸乙烯酯交替共聚合反应的研究

本文研究了马来酸酐（MAn）在过氧化苯甲酰（BP）引发作用下与醋酸乙烯酯（VAc）的交替共聚反应。红外光谱证明了交替共聚物的结构，分析结果表明共聚物是由反应单体技1：1摩尔比例组成。当c（BPO）＝6．8×10~（－3）moi／L，c（VAc）＝3．4×10~（－3）mol／L，p（MAn）＝32．7g／L，63～65℃反应18小时，转化率可达92％以上。     

淀粉/DL-丙交酯接枝共聚物的合成和生物降解性能研究

以淀粉为接枝骨架 ,DL 丙交酯为接枝单体 ,在无水LiCl存在下 ,合成了淀粉 /DL 丙交酯接枝共聚物 .研究了接枝反应的投料比、反应时间、反应温度对单体转化率 (C % )、接枝率 (G % )和接枝效率 (GE % )的影响 .当DL 丙交酯与淀粉结构单元的摩尔比为 10∶1,反应温度为 80～ 85℃ ,反应时间为 4h ,C % ,G %和GE %可分别达到 37 3 %、179 7%和 6 8 0 % .用差示扫描量热 (DSC)分析仪、红外光谱仪和X 射线衍射仪对合成的接枝共聚物进行了表征 ,结果表明 ,淀粉和DL 丙交酯反应生成了淀粉 /DL 丙交酯接枝共聚物 .防水实验结果表明 ,该产物在给定条件下可使纸板的吸水率由 41 1%降低到 1 0 % .降解实验表明该接枝共聚物能够被酸、碱及微生物完全降解     

铬酸引发丙烯酸正丁酯与淀粉接枝共聚反应

作为淀粉改性方法之一 ,不饱和酸及其酯与淀粉接枝共聚反应是一个较新的研究领域 ,其中以 Ce4 +离子作为引发剂的较多[1,2 ] ,也有用Mn3+-H2 SO4 体系 [3]和 Mn[( H2 P2 O7) 3]3-引发体系的[4 ] 。铬酸是一种具有强氧化性的强酸 ,虽然它单独存在时并不引发乙烯类单体的聚合 ,有报道[5] 铬酸可以引发丙烯腈与苎麻纤维素接枝共聚 ,淀粉和纤维素同属于碳水化合物。本文对铬酸引发丙烯酸正丁酯与淀粉接枝共聚反应进行了研究 ,考察了反应条件对接枝反应的影响。1　实验部分1 .1　原料可溶性淀粉 (北京奥特生物技术责任有限公司 ) ,丙烯酸正丁…     

Initiator‐fragment incorporation radical copolymerization of vinyl acetate and 1,2‐polybutadiene as a multivinyl monomer

The copolymerization of vinyl acetate (VAc) with 1,2‐polybutadiene (1,2‐PB; 85.5% 1,2‐units and 14.5% 1,4‐units) as a multivinyl monomer was carried out at 80 °C in dioxane with dimethyl 2,2′‐azobisisobutyrate (MAIB) at high concentrations (0.10–0.50 mol/L) as an initiator. The copolymerization of 1,2‐PB [0.80 mol/L (monomer unit)] and VAc (1.20 mol/L) with MAIB (0.30 mol/L) for 4 h proceeded homogeneously without gelation to yield a soluble copolymer. The resulting copolymer was divided into methanol‐ and n‐hexane‐insoluble parts, of which the yields based on the total weight of the comonomers and initiator were 46 and 20%, respectively. The methanol‐insoluble part consisted of the fractions of the 1,2‐PB units with (9 mol %) and without (39 mol %) an intact double bond, the 1,4‐PB unit (8 mol %), the VAc unit (32 mol %), and the methoxycarbonylpropyl group (12 mol %) as the MAIB fragment, whereas the hexane‐insoluble one was composed of the fraction of the 1,2‐PB units with (4 mol %) and without (17 mol %) a double bond, the 1,4‐PB unit (4 mol %), the VAc unit (60 mol %), and the methoxycarbonylpropyl group (15 mol %). The use of higher concentrations of 1,2‐PB and VAc and lower concentrations of MAIB resulted in gelation. The cast film from a chloroform solution of the methanol‐insoluble part contained spherical pores organized in a hexagonal way with a monodisperse pore size of 3 μm. The copolymer molecules seemed to be arranged in an ordered way on the surface layer of the pores, as shown by an optical microscopy image under crossed polarizers. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2328–2337, 2006     

马来酸二丁基锡的合成及其共聚合

马来酸二丁基锡的合成及其共聚合刘云桥金根河李福绵（北京大学化学与分子工程学院北京１００８７１）关键词马来酸二丁基锡，醋酸乙烯酯，交替共聚物，光聚合关于马来酸酐［１］，马来酰亚胺 Ｎ 取代物［２，３］与富电子烯类单体如苯乙烯，醋酸乙烯酯，乙烯基烷基醚...     

RAFT/MADIX copolymerization of vinyl acetate and 5,6‐benzo‐2‐methylene‐1,3‐dioxepane

The synthesis of well‐defined degradable poly(vinyl acetate) analogues is achieved by RAFT copolymerization of 5,6‐benzo‐2‐methylene‐1,3‐dioxepane (BMDO) and vinyl acetate (VAc) using methyl (ethoxycarbonothioyl)sulfanyl acetate (MEA) as controlling agent. Several monomer mixtures with low BMDO contents (<30 mol %) are employed to prepare different copolymers. In all the cases, the evolution of molar masses and the dispersity values (<1.26) confirm the controlled feature of the polymerization. The livingness of the obtained chains is demonstrated by successful chain extension experiments with VAc, although the presence of dead chains is also shown. The introduction of ester groups into the main chain of these P(VAc‐co‐BMDO) copolymers allows their degradation when treated with a mixture of KOH/MeOH in reflux during 2.5 h. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 104–111     

木薯淀粉与丙烯酸接枝共聚制备淀粉增稠剂

用过硫酸盐 (过硫酸纳、钾或胺盐 )氧化法使木薯淀粉与丙烯酸接枝共聚。探索到最佳反应温度 55℃ ,反应时间 3h ,单体用量 3.1 2 5mol/L ,引发剂浓度 3.5mmol/L ,接枝百分率可达 70 %以上。产品用作淀粉糊的增稠起到明显的效果     

[Mn(H_2P_2O_7)_3]~(3-)引发淀粉与丙烯腈接枝聚合反应的动力学研究

以[Mn(H_2P_2O_7)_3]~(3-)为引发剂,研究了丙烯腈与玉米淀粉的接枝共聚反应。由实验结果求出了反应速率与引发剂浓度、单体浓度、淀粉浓度和反应温度的关系,推导并验证了接枝反应动力学模型,探讨了反应机理,求得了接枝反应活化能。     

Grafting onto Wool. IX. Graft Copolymerization of Vinyl Monomers by Use of Vanadium Oxyacetylacetonate as Initiator

Methyl methacrylate (MMA), acrylic acid (AAc), and vinyl acetate (VAc) were graft copolymerized onto Himachali wool in an aqueous medium by using vanadium oxyacetyl acetonate as initiator. Graft copolymerization was studied at 45, 55, 65, and 75°C for various reaction periods. The percentage of grafting was determined as functions of concentration of monomers, concentration of initiator, time, and temperature. The maximum percentage of grafting with each monomer occurred at 55°. Several grafting experiments were carried out in the presence of various additives which include HNO3, DMSO, and pyridine. Nitric acid was found to promote grafting of MMA. All these additives had adverse effects on grafting of VAc and AAc. MMA, VAc, and AAc were found to differ in reactivity toward grafting and followed the order MMA > AAc > VAc.     

米根霉细胞壁结构性多糖与丙烯酸接枝共聚反应研究

化学改性天然高分子絮凝剂是利用天然高分子物质进行化学改性而成的。与人工合成的有机高分子絮凝剂相比,它具有选择性大、无毒、价廉、易降解等优点,因此将会有广阔的应用前景,近几年,将乙烯基单体接枝到生物高分子上的工作引起了人们的兴趣,这种天然高分子与合成高分子的结合有可能得到理想的性能,获得新的材料：如生物降解塑料、絮凝剂、离子交换剂等,目前这方面的研究主要中在纤维素、淀粉和壳聚糖的接枝共聚上。     

无卤阻燃丙烯腈共聚物的制备及性能

以K₂S₂O₈-NaHSO₃ 氧化还原体系为引发剂, 采用水相沉淀自由基聚合法合成丙烯腈(AN)-醋酸乙烯酯(VAc)无规共聚物[P(AN-co-VAc)], 然后在KOH水溶液中进行P(AN-co-VAc)中VAc单元的选择性水解, 再与磷酸和尿素进行磷酰化反应, 制备无卤阻燃丙烯腈共聚物. 用核磁共振氢谱(¹H NMR)、傅里叶变换红外光谱(FTIR)、差示扫描量热(DSC)和热重分析(TGA)对聚合物结构及热性能进行表征, 用凝胶渗透色谱(GPC)测定了P(AN-co-VAc)的分子量及其分布, 并利用FTIR和扫描电子显微镜(SEM)对无卤阻燃丙烯腈共聚物的炭残渣进行分析. 结果表明, VAc与AN发生共聚反应, 制得了P(AN-co-VAc), 随着KOH水溶液pH值的增大, P(AN-co-VAc)中VAc单元迅速水解; DSC分析结果表明, 随着共聚物中VAc单元含量的增大, 共聚物的环化放热分解峰值温度(T_p)增大, 当VAc单元的质量分数为25%时, T_p最大值高达328 ℃, 而阻燃丙烯腈共聚物的T_p高达340 ℃; TGA分析结果表明, 阻燃共聚物在800 ℃时的炭残渣量高达55%以上, 远高于P(AN-co-VAc)的41%, 具有良好的成炭性; 炭残渣的FTIR及SEM结果表明, 阻燃丙烯腈共聚物的阻燃属于凝聚相阻燃.     

Mn2(CO)10‐induced controlled/living radical copolymerization of vinyl acetate and methyl acrylate: Spontaneous formation of block copolymers consisting of gradient and homopolymer segments

The controlled/living radical polymerization of vinyl acetate (VAc) and its copolymerization with methyl acrylate (MA) were investigated in bulk or fluoroalcohols using manganese complex [Mn₂(CO)₁₀] in conjunction with an alkyl iodide (R? I) as an initiator under weak visible light. The manganese complex induced the controlled/living radical polymerization of VAc even in the fluoroalcohols without any loss of activity. The R? I/Mn₂(CO)₁₀ system was also effective for the copolymerization of MA and VAc, in which MA was consumed faster than VAc, and then the remaining VAc was continuously and quantitatively consumed after the complete consumption of MA. The ¹H and ¹³C NMR analyses revealed that the obtained products are block copolymers consisting of gradient MA/VAc segments, in which the VAc content gradually increases, and homopoly(VAc). The use of fluoroalcohols as solvents increased the copolymerization rate, controllability of the molecular weights, and copolymerizability of VAc. The saponification of the VAc units in poly(MA‐grad‐VAc)‐block‐poly(VAc) resulted in the corresponding poly(MA‐co‐γ‐lactone)‐block‐poly(vinyl alcohol) due to the intramolecular cyclization between the hydroxyl and neighboring carboxyl groups in the gradient segments. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1343–1353, 2009     

Grafting onto Wool. XXVII. Graft Copolymerization of MixeD Vinyl Monomers by Use of Ceric Ammonium Nitrate as Redox Initiator

In order to ascertain the effect of a donor monomer, vinyl acetate (VAc), on the graft copolymerization of acceptor monomers, ethyl acrylate (EA) and butyl acrylate (BA), grafting of mixed vinyl monomers (EA + VAc) and (BA + VAc) was carried out on Himachali wool in aqueous medium using ceric ammonium nitrate (CAN) as a redox initiator. Graft copolymerization was carried out at different temperatures for various reaction periods. Percent grafting and percent efficiency were determined as functions of 1) concentration of mixed vinyl monomers, 2) concentration of CAN, 3) concentration of HNO₃ 4) temperature, and 5) reaction time. VAc, the donor monomer, was found to decrease percent grafting of EA and BA onto wool.     

淀粉-醋酸乙酯-丙烯酸乙酯接枝共聚物

在硝酸铈铵(CAN)以及硫酸亚铁/过氧化氢两种引发体系中，进行了丙烯酸乙酯(EA)、醋酸乙烯酯(VAc)与玉米淀粉的接枝共聚。用质子核磁共振研究了接枝支链的化学组成、用X衍射研究接枝共聚物结晶结构的变化、用扫描电镜研究了材料的微观结构、并研究了共聚物的亲水性。制备了接枝淀粉、聚乙烯醇的生物降解塑料，测定了材料的力学性能以及疏水性。     

腐植酸与苯乙烯的接枝共聚改性

研究了腐植酸(HA)与苯乙烯(St)以H_2O_2-FeCl_2为引发体系的接枝共聚。结果表明,HA对St聚合有阻聚及滞聚作用。接枝度在H_2O_2/FeCl_2=3(摩尔比)时有极大值,提高聚合温度可使接枝效率和接枝度同时增加、增加St-HA的用量比可使接枝度增加,但接枝效率降低,接枝比基本不变。由接枝共聚物的红外光谱分析得出HA与PSt是以C-O-C连接的。接枝共聚物的磺化产物在水和酸性介质中均能溶解。     

Synthesis and Biodegradation of St-g-poly（MMA-co-VAc） Initiated by Manganic Pyrophosphate

Methyl methacrylate (MMA) and vinyl acetate (VAc) were grafted onto corn starch with manganic pyrophosphate { [Mn(H2P2O7)3]^3- } as the initiator and water as the reaction medium, The influences of reaction conditions, including pH value, initiator concentration, monomer concentration and its composition, on percent grafting and grafting efficiency were investigated. The graft copolymer was characterized by means of IR spectroscopy, scanning electron micrograph(SEM) and ^1H NMR spectroscopy. The biodegradation experiment showed that the degradation of corn starch-g-poly(MMA-co-VAc) was mainly from starch. However,after poly VAc in the side chain was transformed into poly vinyl alcohol(PVA), both starch and the grafted side chain could be degraded completely.     

Studies on graft copolymerization onto cellulose derivatives. XXVII. Photo-induced graft copolymerization onto nitrocellulose

Photo-induced graft copolymerization was investigated using nitrocellulose having a different nitrogen content, especially by a noncatalytic method. The effects of a sample nitrogen content, reaction temperature, and monomer, sample, solvent and photosensitizer concentrations on the degree of grafting, the grafting efficiency, and the apparent number of grafted chains were examined. Methyl methacrylate (MMA) and methyl acrylate (MA) easily polymerized, but acrylamide (AAm), vinyl acetate (VAc), and styrene (St) scarcely polymerized. The apparent activation energies were 4.1–11.5 kcal/mol, indicating the small value in the high nitrogen content sample. The degree of grafting and the apparent number of grafted chains increased with increasing monomer and sample concentrations. In every case, the grafting efficiency was at a high level, above 90%. The polymerization did not occur without the sample in the same condition. Furthermore, a part of nitro groups split off by the irradiation of light. With respect to these results, the mechanisms of the photo graft copolymerization was discussed.     

甲基丙烯酸2-N,N-二甲氨基乙酯与甲基丙烯酸甲酯的氧化共聚合的机理研究

研究了CuCl/五甲基二亚乙基三胺(PMDETA)催化的甲基丙烯酸2-N,N-二甲氨基乙酯(DMAEMA)与甲基丙烯酸甲酯(MMA)在氧气存在下的氧化共聚合,通过改变单体配比、催化剂浓度和反应温度对实验条件进行研究.结果显示,在本实验中的单体配比([DMAEMA]∶[MMA]=10∶0～5∶5)、催化剂浓度([CuCl/PMDETA3]=3.1×10-5 mol/L～6×10-3 mol/L)和反应温度(30～80℃)下,聚合均可以顺利发生,而且聚合过程中单体转化率和所得聚合物的分子量都随着反应进行而增加,且分子量呈现宽分布.1H-NMR结果显示所得聚合物中含有DMAEMA和MMA的单体单元.DSC结果显示所得聚合物是一个部分相容体系.利用此方法所得的PDMAEMA进行MMA的原子转移自由基聚合(ATRP)扩链过程则证实,所得聚合物具有C—Cl末端官能团.由此可以认为,在以上过程中,O2先将CuCl氧化成[Cu(Ⅱ)Cl]+,[Cu(Ⅱ)Cl]+再将二甲胺基氧化成N—CH2.自由基,N—CH2.自由基与[Cu(Ⅱ)Cl]+构成反向ATRP体系,从而得到以C—Cl为末端的聚合物.     

RING OPENING COPOLYMERIZATION OF SUCCINIC ANHYDRIDE-ETHYLENE OXIDE BY Al(Ⅲ) ORGANOMETALLIC CATALYSTS

Ring opening copolymerization of succinic anhydride (SA) with ethylene oxide (EO)was successfully carried out by using a series of aluminum-based catalyst in 1,4-dioxane at62±2℃. The results showed that in-situ AlR_3-H_2O (R=ethyl, iso-butyl) catalysts gavehigher molecular weight (M_w～10~4), while Al(OR)_3 catalysts gave the higher alternatingcopolymer structure with slightly lower molecular weight. The in-situ AlR_3-H_2O systemshave been evaluated in more detail for the reaction which showed the optimum H_2O/Almolar ratio to be 0.5. The copolymers with different composition (F_(SA)/F_(EO)= 36/64to 45/55 mol/mol) were synthesized by using different monomer feed ratio. The melt-ing point (T_m), glass transition temperature (T_g) and enthalpy of fusion (ΔH_f) of thesecopolymers are depended on the copolymer composition and in the range of 87～102℃,-12～-18℃, and 37～66J/g, respectively. The second heating scan of DSC also in-dicated that the higher alternating copolymer was more easily recrystallized. The onsetdecomposition temperature was more than 300℃ under nitrogen and influenced by thecopolymer composition.     

醋酸乙烯酯-丙烯酸丁酯乳液共聚乳胶粒形态演化过程的模拟

将簇迁移动力学拓展应用到共聚形态的研究中，对醋酸乙烯酯 丙烯酸丁酯从间歇到不同加料速率下的半连续乳液共聚实验的乳胶粒形态演化过程进行了模拟，模拟从共聚 均聚转折点开始．结果说明：半连续加料时，随着加料速率加快，相分离程度增加，间歇反应时形成了核壳结构．乳胶粒形态模拟结果与文献对此共聚乳胶粒形态的实验表征结果类似．