Clopyralid detection by using a molecularly imprinted electrochemical luminescence sensor based on the “gate-controlled” effect

A new strategy for trace analysis was proposed by preparing a molecularly imprinted polymer (MIP) sensor. The template molecules of clopyralid were determined based on “gate-controlled” electrochemiluminescence (ECL) measurement. A dense polymer film was electropolymerized on an electrode surface to fabricate the MIP–ECL sensor. The process of template elution and rebinding acted as a gate to control the flux of probes, which pass through the cavities and react on the electrode surface. ECL measurement was conducted in the luminol–H₂O₂ system. A linear relationship between ECL intensity and clopyralid concentrations in the range of 1?×?10^?9 mol/L to 8?×?10^?7 mol/L exists, and the detection limit was 3.7?×?10^?10 mol/L. The prepared sensor was used to detect clopyralid in vegetables. Recoveries of 97.9 % to 102.9 % were obtained. The sensor showed highly selective recognition, high sensitivity, good stability, and reproducibility for clopyralid detection.     

Preparation of MIP grafts for quercetin by tandem aryl diazonium surface chemistry and photopolymerization

The food antioxidant quercetin was used as a template in an ultrathin molecularly imprinted polymer (MIP) film prepared by photopolymerization. Indium tin oxide (ITO) plates were electrografted with aryl layers via a diazonium salt precursor bearing two terminal hydroxyethyl groups. The latter act as hydrogen donors for the photosensitizer isopropylthioxanthone and enabled the preparation of MIP grafts through radical photopolymerization of methacrylic acid (the functional monomer) and ethylene glycol dimethacrylate (the crosslinker) in the presence of quercetin (the template) on the ITO. The template was extracted, and the remaining ITO electrode used for the amperometric determination of quercetin at a working potential of 0.26 V (vs. SCE). The analytical range is from 5.10^?8 to 10^?4 mol L^?1, and the detection limit is 5.10^?8 mol L^?1.

Molecularly Imprinted Polyresorcinol Based Capacitive Sensor for Sulphanilamide Detection

A molecularly imprinted polymer (MIP) based capacitive sensor for antibiotic detection in drinking water and milk has been developed on a gold coated silicon electrode (Au Electrode). The electrode was fabricated by electropolymerizing monomer resorcinol (RN) on Au surface in presence of sulphanilamide (SN) as a template molecule, to get insulated RN polymer antibiotic composite. The insulation of the polymer film was improved by incubation of electrode in 1‐Dodecanethiol solution. Subsequently MIP sensor was obtained by extraction of SN in ethanol and acetic acid solution. Electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) measurements were performed for characterization of the developed MIP electrode at different steps of fabrication. The surface morphology of MIP electrode was characterized using atomic force microscopy (AFM), X‐ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive x‐ray spectroscopy (EDS). Performance of MIP sensor was evaluated by measuring change in capacitance against varying concentration of SN using EIS. A linear response in the range 1 to 200 μg L^?1 SN was recorded for MIP sensor with a detection limit of 0.1 μg L^?1. The developed MIP sensor exhibited good selectivity towards SN in water and milk with recoveries in the range 92 % to 105 %. The obtained results suggest the usability of MIP based sensor for SN estimation in water and milk samples.     

Formation of a protein monomolecular layer by a combined technique of LB and SA methods

This paper describes a technique developed for the formation of the self-assembled protein monomolecular layer. The main idea is a direct transfer of protein molecules consisting of a Langmuir-Blodgett (LB) film onto the surface of another chemically modified metal substrate and induction of the spontaneous formation of a self-assembled monolayer (SAM) by chemisorption without protein aggregates. In the present experiments, a cytochrome c (cyt c) SAM on a gold substrate was prepared by incubating a EDC/MUA-modified gold substrate overlaid with a cyt c LB film in a phosphate buffer solution. Scanning tunneling microscopy (STM) image of a cyt c SAM shows that the size of cyt c clusters in the most part of the substrate is approximately 5 nm, indicating the cyt c monomolecular layer. The rectifying property of a cyt c monolayer was confirmed to remain by an asymmetric I-V curve in the applied bias from -1 V to 1 V.     

Evaluation of the Analytical Potentialities of a Composite Electrode Modified with Molecularly Imprinted Polymers

Abstract

The preparation of a methacrylate polymer molecularly imprinted (MIP) with paracetamol (APAP) was performed. After extraction of the APAP template molecule, the MIPs were incorporated into a graphite–polyurethane (GPU) matrix, and the resulting composites were used to prepare modified electrodes intended to be used in APAP determination. The best results were found using a 2.5% MIP in the GPU electrode and a 500-µm MIP particle size. This electrode was used in the determination of APAP in pharmaceutical formulations, reaching a 6.7 × 10^?8 mol L^?1 limit of detection. The 2.5% MIP-GPU-modified electrode showed better sensitivity than the nonimprinted methacrylate GPU-modified electrodes. Interference of phenacetin in the APAP response decreased remarkably when the proposed electrode was used.     

pH-Induced changes in adsorbed cytochrome c. voltammetric and surface-enhanced resonance Raman characterization performed simultaneously at chemically modified silver electrodes

The influence of pH on the redox properties of cytochrome c (cyt c) adsorbed on roughened silver electrodes chemically modified with a self-assembled monolayer (SAM) of 11-mercapto-1-undecanoic acid (MUA) was studied with voltammetric techniques in combination with surface-enhanced resonance Raman scattering (SERRS). The experiments were performed simultaneously on the same electrode sample in a homemade spectroelectrochemical cell suitable for such applications. At pH 7.0 cyt c was found in its native state; at higher pH values (ranging from 8.0 to 9.0) the redox properties of the adsorbed protein varied considerably, featuring a redox behavior which does not resemble the one reported for the alkaline transition. Our results instead indicate the presence of an electrochemically inactive 6cLS species immobilized on MUA at pH 9.0. The pH-induced conformational changes observed for cyt c immobilized on the SAM of MUA were found to be repeatable and chemically reversible, meaning that the recovery of the electrochemical signal due to the native protein occurred instantaneously (on the second time scale) when the electrode was switched back to pH 7.0. The pH-induced changes observed were attributed to a conformational change involving a heme reorientation with respect to the electrode surface.     

Electrochemical Sensor Prepared from Molecularly Imprinted Polymer for Recognition of 1,3-Dinitrobenzene (DNB)

An electrochemical sensor was modified with multi‐wall carbon nanotubes (MWCNT) and molecularly imprinted polymer (MIP) material synthesized with acrylamide and ethylene glycol dimethacrylate (EGDMA) in the presence of 1,3‐dinitrobenzene (DNB) as the template molecule. The MWCNT and MIP layers were successively modified on the surface of a glassy carbon electrode (GCE), of which the MIP film works as an artificial receptor due to its specific molecular recognition sites. The MIP material was characterized by FT‐IR and electrochemical methods of square wave voltammetry (SWV). The interferences of other nitroaromatic compounds (NAC) such as 2,4,6‐trinitrotoluene (TNT), 1,3,5‐trinitrobenzene (TNB) and 2,4‐dinitrotoluene (DNT) to DNB were also investigated by the prepared MIP/MWCNT electrode. Compared with other traditional sensors, the MIP/MWCNT modified electrode shows good selectivity and sensitivity. In addition, the current responses to DNB are linear with the concentration ranging from 4.5×10^?8 to 8.5×10^?6 mol/L with the detection limits of 2.5×10^?8 (?0.58 V) and 1.5×10^?8 mol/L (?0.69 V) (S/N=3). The construction process of MIP/MWCNT modified electrode was also studied as well. All results indicate that the MIP/MWCNT modified electrode established an improving way for simple, fast and selective analysis of DNB.     

Interfacial potentiometry with double poles sensor based on molecularly imprinted polymer for monitoring of 4-aminoazobenzene

A 4-aminoazobenzene (4-AAB) molecularly imprinted polymer (MIP) film was synthesised on the surface of a pencil graphite electrode (PGE) through electropolymerisation technique. After removing the template molecular 4-AAB with ultrasonic clean, 4-AAB-MIP-PGE was obtained. Under interfacial potentiometry with double poles (IPDP), the factors influencing the performance of this electrode were studied and optimised. Based on the rebinding of MIP to template molecular, which resulted in the changing of the interfacial potential at the corresponding interface, an IPDP sensor for the selective determination of 4-AAB was prepared. By recording the zero current potential E_ZCP, where circuit current I was equal to zero in the I–E curve, the changing of interfacial potential of this sensor was monitored. With the concentrations of 4-AAB increasing, the I–E curve shifted positively. And, the zero current potential was linearly related with the logarithm of the 4-AAB concentration in the range from 0.197 to 197 µg L^?1 with a detection limit of 0.135 µg L^?1 (S/N = 3). The sensor was used to determine the concentration of 4-AAB in waste water samples with the recoveries from 98.8% to103.0%.     

Electrochemical Investigation of Cytochrome c Immobilized onto Self‐Assembled Monolayer of Captopril

The electrochemical behavior of cytochrome c (cyt‐c) that was electrostatically immobilized onto a self‐assembled monolayer (SAM) of captopril (capt) on a gold electrode has been investigated. Cyclic voltammetry, scanning electrochemical microscopy (SECM) and electrochemical impedance spectroscopy were employed to evaluate the blocking property of the capt SAM. SECM was used to measure the bimolecular electron transfer (ET) kinetics (k_BI) between a solution‐based redox probe and the immobilized protein. In addition, the tunneling ET between the immobilized protein and the underlying gold electrode was calculated. A k_BI value of (5.0±0.6)×10⁸ mol^?1 cm³ s^?1 for the bimolecular ET and a standard tunneling rate constant (k⁰) of 46.4±0.2 s^?1 for the tunneling ET have been obtained.     

Enhanced electrochemiluminescence of luminol at the gold nanoparticle/carbon nanotube/electropolymerised molecular imprinting composite membrane interface for selective recognition of triazophos

This paper reports a surface molecular self-assembly strategy for imprinting triazophos in the electropolymerised poly(aminthiophenol) (PATP) membranes at the surface of gold nanoparticle (AuNP)/carbon nanotube (CNT) composites modified glassy (GC) electrode for electrochemiluminescent (ECL) detection of pesticide triazophos. The electrochemical and ECL behaviours of luminol at the imprinted PATP/AuNP/CNT/GC electrode were investigated before and after the rebinding of triazophos. It was also found that the ECL intensity was strikingly enhanced by the adsorbed triazophos molecules in the imprinted PATP/AuNP/CNT composite membranes, which was about 5.2-fold as compared with the blank ECL intensity. On this basis, the molecularly imprinted polymer (MIP)-ECL sensor is established for high sensitive and selective detection of triazophos residues in vegetable samples. The resulting MIP-ECL sensor shows wide linear ranges from 3.1 × 10^?8 to 3.1 × 10^?5 g L^?1 with lower detection limit of 3.1 × 10^?9 g L^?1 for triazophos. Moreover, the MIP-ECL sensor has the advantages of high sensitivity, speed, specificity, stability and can become a promising technique for organophosphate pesticide detection.     

Electrochemical sensor for determination of aflatoxin B1 based on multiwalled carbon nanotubes-supported Au/Pt bimetallic nanoparticles

A sensitive and selective imprinted electrochemical sensor for the determination of aflatoxin B₁ (AFB₁) was constructed on a glassy carbon electrode by stepwise modification of functional multiwalled carbon nanotubes (MCNTs), Au/Pt bimetallic nanoparticles (Au/PtNPs), and a thin imprinted film. The fabrication of a homogeneous porous poly o-phenylenediamine (POPD)-grafted Au/Pt bimetallic multiwalled carbon nanotubes nanocomposite film was conducted by controllable electrodepositing technology. The sensitivity of the sensor was improved greatly because of the nanocomposite functional layer; the proposed sensor exhibited excellent selectivity toward AFB₁ owing to the porous molecular imprinted polymer (MIP) film. The surface morphologies of the modified electrodes were characterized using a scanning electron microscope. The performance of the imprinted sensor was investigated by cyclic voltammetry, differential pulse voltammetry, and electrochemical impedance spectroscopy in detail. A linear relationship between the sensor response signal and the logarithm of AFB₁ concentrations ranging from 1?×?10^?10 to 1?×?10^?5 mol L^?1 was obtained with a detection limit of 0.03 nmol L^?1. It was applied to detect AFB₁ in hogwash oil successfully.     

Capacitive Chemical Sensor for Thiopental Assay Based on Electropolymerized Molecularly Imprinted Polymer

A novel capacitive sensor based on electropolymerized molecularly imprinted polymer (MIP) for thiopental detection is described. The molecularly imprinted film as a recognition element was prepared by electropolymerization of phenol on a gold electrode in the presence of thiopental (template). Cyclic voltammetry and capacitive measurements were used for characterization and evaluation of the polymeric film. The template molecules were removed from the modified electrode surface by washing with an ethanol:water solution. The sensor’s linear response range was between 3 and 20 µM, with a detection limit of 0.6 µM. The proposed sensor exhibited good selectivity, reproducibility. Satisfactory results were obtained in the direct detection of real samples.     

Preparation of MIP grafts for quercetin by tandem aryl diazonium surface chemistry and photopolymerization

The food antioxidant quercetin was used as a template in an ultrathin molecularly imprinted polymer (MIP) film prepared by photopolymerization. Indium tin oxide (ITO) plates were electrografted with aryl layers via a diazonium salt precursor bearing two terminal hydroxyethyl groups. The latter act as hydrogen donors for the photosensitizer isopropylthioxanthone and enabled the preparation of MIP grafts through radical photopolymerization of methacrylic acid (the functional monomer) and ethylene glycol dimethacrylate (the crosslinker) in the presence of quercetin (the template) on the ITO. The template was extracted, and the remaining ITO electrode used for the amperometric determination of quercetin at a working potential of 0.26 V (vs. SCE). The analytical range is from 5.10⁻⁸ to 10⁻⁴ mol L⁻¹, and the detection limit is 5.10⁻⁸ mol L⁻¹.

This work describes the grafting of a molecularly imprinted polymer (MIP) film by combining diazonium surface chemistry and surface-initiated photopolymerization. The MIP grafts specifically and selectively recognize quercetin in pure solution in THF and in real green tea infusion.

     

Nanoporous gold electrode prepared from gold compact disk as the anode for the microbial fuel cell

The electrodes (anode and cathode) have an important role in the efficiency of a microbial fuel cell (MFC), as they can determine the rate of charge transfer in an electrochemical process. In this study, nanoporous gold electrode, prepared from commercially available gold-made compact disk, is utilized as the anode in a two-chamber MFC. The performance of nanoporous gold electrode in the MFC is compared with that of gold film, carbon felt and acid-heat-treated carbon felt electrodes which are usually employed as the anode in the MFCs. Electrochemical surface area of nanoporous gold electrode exhibits a 7.96-fold increase rather than gold film electrode. Scanning electron microscopy analysis also indicates the homogeneous biofilm is formed on the surface of nanoporous gold electrode, while the biofilm formed at the surface of acid-heat-treated carbon felt electrode shows rough structure. Electrochemical studies show although modifications applied on carbon felt electrodes improve its performance, nanoporous gold electrode, due to its structure and better electrochemical properties, acts more efficiently as the MFC’s anode. The maximum power density produced by nanoporous gold anode is 4.71 mW m^?2 at current density of 16.00 mA m^?2, while this value for acid-heat-treated carbon felt anode is 3.551 mW m^?2 at current density of 9.58 mA m^?2.     

Novel Screen-Printed Gold Nano Film Electrode for Trace Mercury(II) Determination Using Anodic Stripping Voltammetry

Integrating the screen printing technique with the vacuum evaporation method, we developed a novel and disposable screen-printed gold film electrode (SPGFE) in the present work. First, a conductive silver layer, a connection graphite-carbon layer, and an insulating polymer layer were successively printed onto a flexible polyethylene terephthalate (PET) substrate. Then, a gold thin film was achieved on the scheduled vacant site by use of the vacuum evaporation method. In order to enhance the electroanalytical performance of the SPGFE, the thickness of the gold film was controlled in the range of 70–80 nm under optimum conditions. The fabricated SPGFE was applied to detect trace mercury(II) based on the square-wave anodic stripping voltammetry (SWASV). The results indicated that the proposed SPGFE exhibited higher sensitivity to trace mercury(II) than the gold disc electrode. The stripping current was linearly related to the concentration of mercury(II) in the range of 16–280 µg/L (R² = 0.9919) and 1.2–8.0 µg/L (R² = 0.9977), with a detection limit of 0.8 µg/L (S/N = 3) under 180 s accumulation. The SPGFE was further used to detect mercury in real samples, and the obtained results revealed a good agreement with those of inductively coupled plasma atomic emission spectrometry (ICP-AES) and atomic absorption spectroscopy (AAS). The highly sensitive and environmental friendly electrode, as another type of “mercury-free” electrode, holds great promise in stripping measurements.     

Selective Electrochemical Determination of Salicylic Acid in Wheat Using Molecular Imprinted Polymers

Salicylic acid is a phytohormone, playing crucial roles in signal transduction, crop growth, and development, and defense to environmental challenges. In this study, a highly selective electrochemical sensor was designed and used to determine salicylic acid using molecularly imprinted polymers for recognition. The electrochemical sensor was fabricated via stepwise modification of gold nanoparticle–graphene–chitosan and molecularly imprinted polymers on a glassy carbon electrode. With electrochemical deposition, a gold nanoparticle–graphene–chitosan film was deposited on the glassy carbon electrode and enhanced the sensitivity. Molecularly imprinted polymers with adsorbed template salicylic acid were added to the surface of the modified electrode. Cyclic voltammetry and electrochemical impedance spectroscopy were used to characterize the modified electrodes. Salicylic acid in wheat was quantified by the sensor using the molecularly imprinted polymer/gold nanoparticle–graphene–chitosan/glassy carbon electrode. Concentrations of salicylic acid from 5?×?10^?10 to 5?×?10^?5?mol?L^?1 were determined showing that the developed sensor was suitable for the analysis of food.     

An Electrochemical Sensor for L-Tryptophan Using a Molecularly Imprinted Polymer Film Produced by Copolymerization of o-Phenylenediamine and Hydroquinone

An electrochemical sensor for L-tryptophan based on a molecularly imprinted polymer was developed. The sensing film was prepared by the co-electropolymerization of o-phenylenediamine and hydroquinone on a gold electrode in the presence of L-tryptophan as the template. The performance of the L-tryptophan sensor was characterized by cyclic voltammetry, differential pulse voltammetry, and alternating current impedance. Under the optimal experimental conditions, the relative current change was linear to the concentration of L-tryptophan in the range of 1.0 × 10^?8 to 1.0 × 10^?6 mol/L and a detection limit of 0.50 × 10^?8 mol/L was obtained. The sensor showed high sensitivity and selectivity for L-tryptophan. The imprinting factor was 3.58 and selectivity factors of L-tryptophan compared to analogs were larger than 2. The sensor also demonstrated good resistance to acidic, basic, and organic environments.     

Development of a cytochrome c-based screen-printed biosensor for the determination of the antioxidant capacity of orange juices

This paper describes the development of an amperometric cytochrome c (cyt c)-based biosensor and its later application to the quantification of the scavenging capacity of antioxidants. The enzymatic biosensor was constructed by covalently co-immobilizing both cyt c and XOD on a mercaptoundecanol/mercaptoundecanoic acid (MU/MUA) mixed self-assembled monolayer (SAM)-modified screen-printed gold electrode. The applicability of this method was shown by analyzing the antioxidant capacity of pure substances, such as ascorbic acid and Trolox, and natural sources of antioxidants, particularly 5 orange juices.     

Preparation and Adsorption Ability of Molecularly Imprinted Polymer Microspheres for Malachite Green

Molecularly imprinted polymer (MIP) microspheres were synthesized through precipitation polymerization using malachite green (MG) as template, methacrylic acid (MAA) as monomer, and trimethylolpropane trimethacrylate (TRIM) as cross-linker. The microsphere structure of MIP was characterized by IR spectroscopy and SEM. The influence of preparation conditions such as monomer and cross-linker dosages on the polymer absorption of MG in acetonitrile solution was also explored. Under the optimum synthesis conditions (0.25 mmol MG, 1.5 mmol MAA, 2.5 mmol TRIM, 40 mL acetonitrile), the prepared MIP microspheres have a binding capacity as high as 2000 µg g^?1 of MG with an imprinting factor of above 4.0. The result suggests that the prepared MIP microspheres are promising material for the selective extraction of MG in complicated matrix solutions.