Ionic conductance of composite electrolytes based on network polymer with ceramic powder

Effects of ceramic fillers (α-Al₂O₃, γ-Al₂O₃ and BaTiO₃) have been investigated on the ionic conductance of polymeric complexes consisting of poly(ethylene oxide)-modified poly(methacrylate) (PEO-PMA) and lithium bis(trifluoromethylsulfonyl)imide, Li(CF₃SO₂)₂N, and ceramic powder. The addition of ceramic powder increased the ionic conductivity over an ambient temperature range. Conductivity of 4.9 × 10^− 5 S cm^− 1 at 333 K (60 °C) was obtained for the composite containing 15 wt.% α-Al₂O₃ prepared by photo-polymerization. The optimum content of Al₂O₃ was different among the methods of polymerization. The highest conductivity was obtained for the composite containing 5 wt.% of α-, or γ-Al₂O₃ prepared by thermal polymerization. The addition of the ceramic filler scarcely influenced the thermal properties of the polymer matrix. XRD and NMR experiments showed that the ionic mobility could be enhanced in the composites by addition of α-Al₂O₃. The addition of small amounts of ferroelectric BaTiO₃ also increased the ionic conductivity of the polymeric complex, but its extent was smaller than the case of the Al₂O₃ addition.     

Adsorption and dehydrogenation of 2-propanol on the surface of γ-Al2O3-supported gold

The adsorption and reactions of 2-propanol on γ-Al₂O₃ and γ-Al₂O₃-supported gold samples were investigated by infrared (IR) spectroscopy, modulated differential scanning calorimetry (MDSC) and mass spectrometry. Adsorption of the alcohol on the samples at room temperature led to formation of molecularly adsorbed 2-propanol and 2-propoxide species bonded to Al³⁺ sites. Treatment of γ-Al₂O₃ after alcohol adsorption in flowing He from 25 to 300 °C led to 2-propanol desorption, without evidence of surface reactions. In contrast, when supported gold samples were exposed to the same thermal treatment, formation of acetone and H₂ was observed by mass spectra of the effluent gases from the flow reactor. Concomitantly, IR spectra of the samples showed the appearance of a band at 1698 cm^? 1, assigned to ν_CO vibrations of adsorbed acetone. The formation of acetone occurred by the dehydrogenation of 2-propoxide species bonded to Al³⁺ sites, as evidenced by (a) the decrease in the intensities of their IR bands and (b) the presence of a MDSC peak at approximately the same temperature as that at which acetone was formed and the 2-propoxide species were consumed. It is proposed that gold particles on the γ-Al₂O₃ surface facilitate breaking of the β-CH bond of neighboring surface 2-propoxide species to give acetone. Our results emphasize the bifunctional character of supported gold catalysts for the dehydrogenation of alcohols.     

Fabrication and luminescent properties of Al2O3:Cr3 + microspheres via a microwave solvothermal route followed by heat treatment

AlOOH:Cr^3 + powders were synthesized via a microwave solvothermal route at 433 K for 30 min and were used as the precursor and template for the preparation of γ-Al₂O₃:Cr^3 + by thermal transformation at 773 K for 2 h in air. The obtained γ-Al₂O₃ based powders were microspheres with an average diameter about 1.9 μm. Photoluminescence (PL) spectra showed that the Al₂O₃:Cr^3 + particles presented a symmetric broad R band at 696 nm without appreciable splitting when excited at 462 nm. It is shown that the 0.04 mol% of doping concentration of Cr^3 + ions in γ-Al₂O₃:Cr^3 + is optimum. According to Dexter's theory, the critical distance between Cr^3 + ions for energy transfer was determined to be 47.54 Å. Based on the corresponding PL spectrum, full width at half maximum (FWHM) of Al₂O₃:Cr^3 + (0.04 mol%) was calculated to be 3.35 nm.     

XRD and Mössbauer spectroscopy investigation of Fe2O3–Al2O3 nano-composite

Fe₂O₃–Al₂O₃ nano-composites were synthesized by sol–gel means. The properties of samples sintered at various thermal treatment temperatures were investigated by X-ray diffraction (XRD) and Mössbauer spectroscopy (MS). The experimental results show that the γ- to α-Al₂O₃ transformation occurs at lower temperature after iron oxide doping. The samples obtained at 1173 K contained poorly crystallized γ-Al₂O₃ phase and an amorphous iron oxide. When the temperature of heating was increased to 1373 K, the sample was composed of α-Fe₂O₃/α-Al₂O₃ nano-composite and some solid solution. A superparamagnetic phenomenon was observed until the thermal treatment temperature reached 1373 K.     

Synthesis of alumina supported nickel nanoparticle catalysts and evaluation of nickel metal dispersions by temperature programmed desorption

The purpose of this study was to synthesize highly dispersed Ni/Al₂O₃ catalysts and to develop a suitable hydrogen-temperature programmed desorption (H₂-TPD) method for the determination of nickel metal surface area, dispersion, and crystallite sizes. Several highly dispersed Ni/Al₂O₃ catalysts with a Ni loading between 15 and 25 wt.% were synthesized. The reducibility of catalysts was determined by temperature programmed reduction (TPR) experiments. All catalysts exhibited a single reduction peak with a maximum rate of H₂ consumption (T_max in TPR) occurring below 450 °C. Three different H₂-TPD methods were employed to determine the amount of H₂ chemisorbed. In TPD-1, a 10% H₂/Ar mixture was used for catalyst pre-reduction and surface saturation by cooling down from T_max in TPR to room temperature. In TPD-2, the catalyst surface after pre-reduction was flushed with Ar at T_max in TPR + 10 °C. The TPD-3 was similar to the TPD-2, but used 100% H₂ instead of 10% H₂/Ar mixture. In all three TPD methods, the profiles exhibited 2 domains of H₂ desorption peaks, one below 450 °C, referred to as type-1 peaks, and attributed to H₂ desorbed from exposed fraction of Ni atoms, and the other above 450 °C, denoted as type-2 peaks, and assigned to the desorption of H₂ located in the subsurface layers and/or to spillover H₂. Flushing the reduced catalyst surface in Ar at T_max in TPR + 10 °C in TPD-2 and TPD-3 removed most of the H₂ located in the subsurface layers/ spillover H₂. The amount of H₂ chemisorbed to form a monolayer on the reduced Ni/Al₂O₃ catalysts was determined quantitatively from the TPD peak areas of type-1 peaks in TPD-1, and from both type-1 and type-2 peaks in TPD-2 and TPD-3. The Ni metal surface area, dispersions and crystallite sizes were calculated from the chemisorption data and the values were compared with those obtained using the static chemisorption method. Both TPD-2 and TPD-3 gave chemisorption results similar to that obtained from the static method.     

Surface properties of palladium catalysts supported on ternary ZrO2–Al2O3–WOx oxides prepared by the sol–gel method: Study of the chemical state of the support

The surface properties of Pd and Pd–Pt catalysts supported on binary ZrO₂–WOx and ternary ZrO₂–Al₂O₃–WOx oxides prepared by the sol–gel method were studied. Special attention was paid to the study of the texture of the catalysts as well as the chemical state of tungstated zirconia and tungstated zirconia promoted with alumina in the palladium catalysts. The catalysts were tested in the isomerization of n-hexane and were characterized by N₂ physisorption, XRD, TPR, Raman spectroscopy, XPS and FT-IR of adsorbed pyridine. The catalysts had bimodal pore size distributions with mesopores in the range 55–70 Å and macropores of 1000 Å in diameter. The catalysts had a surface WOx coverage (4.4–6.0 W nm^?2) lower than that of the theoretical monolayer (7.0 W nm^?2). A lower acidity of the ternary ZrO₂–Al₂O₃–WOx oxide as compared to the binary ZrO₂–WOx oxide was found. Higher activity in the isomerisation of n-hexane was obtained in the Pd–Pt catalysts supported on ternary ZrAlW oxides prepared by sol–gel that is correlated with the coexistence on the surface of W⁴⁺ (WO₂) or W⁰ and W⁶⁺ (Al₂(WO₄)₃) species, ZrO₂ in the tetragonal phase and a high amount of ZrOx suboxides species in a low oxidation state (Zr³⁺ and Zr²⁺).     

DFT study of carbon monoxide adsorption on α-Al2O3(0001)

The adsorption of CO on α-Al₂O₃(0001) was studied using the DFT-GGA computational method and on α-Al₂O₃ powder experimentally by Infra red spectroscopy. The core and valence level regions of α-Al₂O₃(0001) single crystal surface were also studied experimentally. Ar ions sputtering of the surface results in a slight but reproducible decrease in the XPS O2p lines in the valence band regions due to preferential removal of surface (and near surface) O atoms. Core level XPS O1s and Al2p further confirmed oxygen depletion with an associated surface stoichiometry close to Al₂O_2.9. The adsorption energy of CO was computed and found equal to 0.52 eV for θ = 0.25, it decreased to 0.42 eV at θ = 1. The IR frequency of νCO was also computed and in all cases it was blue shifted with respect to gas phase CO. The shift, Δν, decreased with increasing coverage where it was found equal to 56 cm^? 1 for θ = 0.25 and decreased to 30 cm^? 1 for θ = 1. Structural analyses indicated that the change in the adsorption energy and the associated frequency shift is due to surface relaxation upon adsorption. Experimentally the adsorption of CO gave rise to one main IR peak at 2154 cm^? 1 at 0.3 Torr and above. Two far smaller peaks are also seen at lower pressures of 0.03–0.2 Torr at 2189 and 2178 cm^? 1. The isosteric heat of adsorption was computed for the IR band at 2154 cm^? 1 and was found equal to 0.2 eV which did not change with coverage in the investigated range up to θ = 0.6.     

Fabrication and luminescence properties of Al2O3:Tb3+ microspheres via a microwave solvothermal route

Al₂O₃:Tb³⁺ green phosphors were synthesized via a microwave solvothermal and thermal decomposition route, and characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), photoluminescence (PL) spectra, and decay curves. XRD results indicate that Tb³⁺ doped samples are γ-Al₂O₃ after being calcined at 773 K. SEM results show that the particles of Al₂O₃:Tb³⁺ are hierarchically nanostructured microspheres assembled from nanosheets. The PL spectra indicate that the ⁵D₄→⁷F₅ (545 nm) electric dipole transition is the most intensive when excited at 235 nm. It is shown that 0.7 mol% of doping concentration of Tb³⁺ ions in γ-Al₂O₃:Tb³⁺ is optimum. According to Dexter's theory, the critical distance between Tb³⁺ ions for energy transfer was determined to be 18.4 Å. It is found that the curve followed the single-exponential decay. The excellent chromaticity coordinates of Al₂O₃:Tb³⁺ phosphors, as defined by the International Commission on Illumination (CIE), indicate that it is a good candidate for use in light display systems and optoelectronic devices.     

Dependence of sonochemical parameters on the platinization of rutile titania – An observation of a pronounced increase in photocatalytic efficiencies

Using a standing wave sonochemical reactor (SWSR), the influences of parameters of ultrasonic power input, sonication time, sonication temperature and the amount of propanol (which generates the reducing radicals) were systemically investigated to ascertain and optimize the best conditions for the sonochemical reduction of Pt from its precursor hexachloroplatinic acid and then its deposition on rutile TiO₂ (platinization of rutile titania) catalysts. Catalytic activity of the prepared platinized catalysts was tested in the reaction of methyl orange degradation. The results of photocatalytic activity study in the degradation of methyl orange further demonstrate that sonochemically as-prepared Pt/TiO₂ catalysts show a pronounced increase (～2 times) in photodegradation, even with a deposition of small amounts of platinum (1.4 wt.%), as compared to the unsupported or naked rutile titania. Although there are various parameters that influence the sonochemical platinization of rutile titania, the present optimization results clearly indicate that the best photocatalytic degradation of methyl orange can be obtained when the experimental conditions of the preparation were with an input power of 50 W, an initial hexachloroplatinic acid volume of 70 ml (which results into 1.4 wt.% Pt on TiO₂), sonication time of 90 min, 0.18 g of propanol and a temperature of 10 °C were adopted. The method of ultrasound application to prepare metal supported semiconductors has many advantages such as convenience, safety and high efficiency. Furthermore, it is hopeful that this optimization study can also be extended to the generation of similar metal supported semiconductors.     

A versatile sonication-assisted deposition–reduction method for preparing supported metal catalysts for catalytic applications

This work aims to develop a rapid and efficient strategy for preparing supported metal catalysts for catalytic applications. The sonication-assisted reduction–precipitation method was employed to prepare the heterogeneous mono- and bi-metallic catalysts for photocatalytic degradation of methyl orange (MO) and preferential oxidation (PROX) of CO in H₂-rich gas. In general, there are three advantages for the sonication-assisted method as compared with the conventional methods, including high dispersion of metal nanoparticles on the catalyst support, the much higher deposition efficiency (DE) than those of the deposition–precipitation (DP) and co-precipitation (CP) methods, and the very fast preparation, which only lasts 10–20 s for the deposition. In the AuPd/TiO₂ catalysts series, the AuPd(3:1)/TiO₂ catalyst is the most active for MO photocatalytic degradation; while for PROX reaction, Ru/TiO₂, Au–Cu/SBA-15 and Pt/γ-Al₂O₃ catalysts are very active, and the last one showed high stability in the lifetime test. The structural characterization revealed that in the AuPd(3:1)/TiO₂ catalyst, Au–Pd alloy particles were formed and a high percentage of Au atoms was located at the surface. Therefore, this sonication-assisted method is efficient and rapid in the preparation of supported metal catalysts with obvious structural characteristics for various catalytic applications.     

Solid state interactions in nano-sized oxides

Comparative study of reactivity of nano- and micro-sized alumina and nickel oxide, obtained by the electrical explosion of metal wires in oxidizing atmosphere, was carried out for the reactions NiO + MoO₃, NiO + Al₂O₃, and Al₂O₃ + Bi₂O₃ by coupled anneals of ceramics, measurements of the conductivity of individual oxides and raw oxide mixtures, X-ray diffraction and differential thermal analysis. The total conductivity of nano-structured oxides was found lower than that of micro-structured ceramics. Mixing bismuth oxide with nano-structured alumina leads to stabilization of the low temperature polymorph α-Bi₂O₃ up to 780 °C. The diffusion permeability of NiMoO₄ layer grown at the surface of NiO ceramics, having submicron grains, was found 2 times lower if compared to NiMoO₄ grown at micro-sized NiO ceramics. NiO and Al₂O₃ nano-powders preserve the high reactivity even when heated up to 1000 °C. The results are discussed in terms of size effects on the solid state reactivity of oxides.     

Recovery properties of hydrogen gas sensor with Pd/titanate and Pt/titanate nanotubes photo-catalyst by UV radiation from catalytic poisoning of H2S

Recovery properties after H₂S catalytic poisoning of catalytic-type gas sensor with photo-catalysts and UV radiation have been examined. Each sensing material of the sensor consists of Pd, Pt supported on γ-Al₂O₃ and Pd/titanate, Pt/titanate nanotubes or TiO₂ particles. Pd/titanate and Pt/titanate nanotubes photo-catalyst were synthesized by hydrothermal synthesis method. All the sensors were deactivated after 500 ppm H₂S exposure for 20 h. The sensors with Pd/titanate or Pt/titanate nanotubes showed regenerated voltage response under UV radiation. However the sensor with TiO₂ particles showed negligible regenerated voltage response. Regenerated voltage response with Pd/titanate or Pt/titanate nanotubes may stem from location of Pd or Pt catalyst on the titanate nanotube photo-catalyst.     

Luminescent vacuum ultraviolet spectroscopy of Cr3+ ions in nanostructured aluminum oxide

Impurity Cr³⁺ centers in submicron and nanostructured Al₂O₃ crystals of different phase compositions at temperatures of 300 and 7.5 K were studied by a luminescent vacuum ultraviolet (VUV) spectroscopy method. Photoluminescence (PL) spectra and the energies of ²E, ⁴T₂, and ⁴T₁ excited states of Cr³⁺ ion depend on the type of crystalline samples phase. The PL excitation spectrum of R-line in α-Al₂O₃ nanoscale crystals is formed by intracenter transitions (2.5–5.5 eV region), by charge transfer band (6.9 eV) and by effective formation of impurity-bound excitons (9.0 eV region). Such impurity-bound excitons correspond to O₂p→Al₃s electron transition in surroundings of an impurity Cr³⁺ center. The efficiency of impurity-bound excitons formation decreases with the increase of the grain size above 100 nm. The size dependence is noticeably shown in PL excitation spectra in VUV region. Excitons bound to impurity centers do not appear in nanostructured δ+θ-Al₂O₃ crystals. The effect of the electron excitation multiplication is observed distinctly in nanostrucured α-Al₂O₃ at an excitation energy above 19 eV (more than 2E_g).     

Influence of hydrothermally modified γ-Al2O3 on the properties of NiMo/γ-Al2O3 catalyst

The influence of hydrothermal modification of γ-Al₂O₃ on the properties of NiMo/γ-Al₂O₃ catalyst was investigated in this paper. The experimental results showed that the use of the modified γ-Al₂O₃ in the preparation of the NiMo/γ-Al₂O₃ catalyst led to the increase of the dispersion of the surface Mo and Ni oxides, favored the formation of the poly-molybdates and promoted the reduction of the active Mo oxides owing to the increase of the surface acidity of the modified γ-Al₂O₃. Therefore, the NiMo/γ-Al₂O₃ catalyst supported on the modified γ-Al₂O₃ exhibited a higher hydrodenitrogenation (HDN) activity than that supported on the untreated γ-Al₂O₃ in the temperature range of 300-340 °C.     

Oxygen-rich Ti1−xO2 pillar growth at a gold nanoparticle–TiO2 contact by O2 exposure

In-situ gas-injection transmission electron microscopy revealed that a pillar grew at the edge of the interface of a gold nanoparticle and a TiO₂ substrate during exposure to O₂ gas at 100 Pa. The pillar was found to have a titanium-deficient chemical composition of Ti_1 ? xO₂ (x > 0) by electron energy loss spectroscopy (EELS). The spectra showed a chemical shift of oxygen and titanium ions to have ionic states of Ti³⁺ and O^y? (y < 3/2). The formation of the Ti_1 ? xO₂ at the contact edge of gold–Ti_1 ? xO₂ interface is discussed from the perspective of an O₂ affinity, which plays an important role in CO oxidation process of supported gold particle.     

Surface oxides of Ir(111) prepared by gas-phase oxygen atoms

The Ir(111) surface is oxidized with gas-phase oxygen atoms under vacuum condition to achieve an oxidation level beyond its saturation coverage for chemisorption. Two surface oxides, rutile IrO₂ of (100) domain and corundum Ir₂O₃ of (001) domain, have been grown at 550 K with different oxygen exposure of 3.6 × 10⁵ L and 7.2 × 10⁵ L respectively. The temperature programmed desorption (TPD) experiment of rutile IrO₂(100) shows its desorption curve (at 4 K s^? 1) peaks at 750 K, followed by a long tail of less pronounced desorption features. On the other hand, TPD of corundum Ir₂O₃(001) displays a symmetric trace, peaking at 880 K. Carbon monoxide titration experiments show that adsorbed CO reduces corundum Ir₂O₃(001) at 400 K, but CO does not adsorb on rutile IrO₂(100) and no reduction reaction occurs. Evidently, among the two surface oxides, corundum Ir₂O₃(001) involves in catalysis of carbon monoxide oxidation, while rutile IrO₂(100) does not. The formation of two surface oxides is also compared, we conclude that the atom arrangement favors Ir₂O₃(001) at the oxide/metal interface.     

Adsorption and diffusion of an Au atom and dimer on a θ-Al2O3 (001) surface

With density-functional calculations we have investigated adsorption and diffusion of an Au atom and an Au₂ dimer on a θ-Al₂O₃(001) surface. The surface structure of θ-Al₂O₃(001) has an armchair-like configuration containing flat and trench areas and the Au_n (n = 1 or 2) cluster prefers to adsorb on the flat area. A single Au atom adsorbs on an O–Al bridge site with adsorption energy 0.35 eV, whereas an Au₂ dimer bonds to the oxide with adsorption energy 0.78 eV, with one Au coordinated singly to a surface O. Formation of Au₂ from Au₁ is favored, with a negligible energy barrier. The calculated energy barriers for diffusion indicate that an Au atom diffuses more rapidly than an Au₂ dimer but both prefer to diffuse anisotropically, along the flat area of the θ-Al₂O₃(001) surface.     

STM observation of the origin of electrochemical promotion on metal catalyst-electrodes interfaced with YSZ and β″-Al2O3

Scanning tunneling microscopy (STM) was used to investigate the surfaces of Pt(111) single crystals interfaced with YSZ and β″-Al₂O₃ at atmospheric pressure. In both cases the STM imaged the reversible electrochemically controlled dosing (backspillover) of O²⁻ species and of Na⁺ species on Pt(111) surface respectively, which both form a (12 × 12) hexagonal structure on the Pt(111) surface. On the mechanistic side, the STM has confirmed the backspillover mechanism of electrochemical promotion and metal support interactions.     

Effect of nano γ-Al2O3 addition on ion dynamics in polymer electrolytes

Polymer electrolytes, which hold the key of successful operation of all solid state ionic devices, have been investigated. An amorphous polymer was used to facsimile fast ion transport in the gel polymer electrolytes (GPE) and room temperature conductivity >10⁻³ S/cm can be attained. Further, these electrolytes were transformed into composites by dispersing inorganic particles of γ-Al₂O₃ (11 nm in size) in varying wt.%. An enhancement in the conductivity for an optimum concentration using LiClO₄ as a salt can be obtained and is described in terms of free charge carrier concentration, while the other family of Lithium salts viz. LiTf, LiIm, LiBETI decreases the conductivity marginally. FTIR spectroscopy supports the observed decrease in terms of more association between fillers and salts. It has been realized that the mechanical integrity of these composites increases manifold, without affecting the conductivity, significantly.     

Synthesis of magnetic γ-Fe2O3-based nanomaterial for ultrasonic assisted dyes adsorption: Modeling and optimization

γ-Fe₂O₃ nanoparticles were synthesized and loaded on activated carbon. The prepared nanomaterial was characterized by field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDX), Fourier transforms infrared spectroscopy (FT-IR) and X-ray diffraction (XRD). The γ-Fe₂O₃ nanoparticle-loaded activated carbon (γ-Fe₂O₃-NPs-AC) was used as novel adsorbent for the ultrasonic-assisted removal of methylene blue (MB) and malachite green (MG). Response surface methodology and artificial neural network were applied to model and optimize the adsorption of the MB and MG in their individual and binary solutions followed by the investigation on adsorption isotherm and kinetics. The individual effects of parameters such as pH, mass of adsorbent, ultrasonication time as well as MB and MG concentrations in addition to the effects of their possible interactions on the adsorption process were investigated. The numerical optimization revealed that the optimum adsorption (>99.5% for each dye) is obtained at 0.02 g, 15 mg L⁻¹, 4 min and 7.0 corresponding to the adsorbent mass, each dye concentration, sonication time and pH, respectively. The Freundlich, Langmuir, Temkin and Dubinin–Radushkevich isotherms were studied. The Langmuir was found to be most applicable isotherm which predicted maximum monolayer adsorption capacities of 195.55 and 207.04 mg g⁻¹ for the adsorption of MB and MG, respectively. The pseudo-second order model was found to be applicable for the adsorption kinetics. Blank experiments (without any adsorbent) were run to investigate the possible degradation of the dyes studied in presence of ultrasonication. No dyes degradation was observed.