Enhancement of ethanol sensing of TeO2 nanorods by Ag functionalization

Gas sensors based on Ag–TeO₂ composite nanorods were fabricated using thermal evaporation and sputtering techniques. The morphology, structure and phase composition of the as-prepared nanofibers were characterized by scanning electron microscopy, transmission electron microscopy (TEM), and X-ray diffraction (XRD), respectively. TEM and XRD showed that the nanorods and nanoparticles on them were tetragonal-structured single crystal TeO₂ and a mainly amorphous phase, respectively. The multiple-networked bare TeO₂ nanorod sensors exhibited a response of ～219% at 25 ppm C₂H₅OH at 300 °C, whereas the Ag-functionalized TeO₂ nanorod sensors showed a response of ～808% under the same conditions. The mechanism by which the sensing properties of the TeO₂ nanorods were enhanced by functionalization with Ag is also discussed.     

Selective Synthesis of Mesoporous and Nanorod CeVO<Subscript>4</Subscript> without Template

A simple and efficient method has been established for the selective synthesis of mesoporous and nanorod CeVO₄ with different precursors by sonochemical method. CeVO₄ nanorod can be simply synthesized by ultrasound irradiation of Ce(NO₃)₃ and NH₄VO₃ in aqueous solution without any surfactant or template. While mesoporous CeVO₄ with high specific surface area can be prepared with Ce(NO₃)₃, V₂O₅ and NaOH in the same way. Mesoporous CeVO₄ has a specific surface area of 122 m² g⁻¹ and an average pore size of 5.2 nm; CeVO₄ nanorods have a diameter of about 5 nm, and a length of 100–150 nm. The ultrasound irradiation and ammonia in the reactive solution are two key factors in the formation of such rod-like products. X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), thermogravimetric (TG) and differential thermal analyses (DTA), UV/vis absorption spectroscopy and Brunauer–Emmett–Teller (BET) were applied for characterization of the as-prepared products.     

Controlling the orientation of ZnO nanorod arrays using TiO<Subscript>2</Subscript> thin film templates dip-coated by sol–gel

The oriented ZnO nanorod arrays have been synthesized on a silicon wafer that coated with TiO₂ films by aqueous chemical method. The morphologies, phase structure and the photoluminescence (PL) properties of the as-obtained product were investigated by field-emission scanning electron microscopy (FE-SEM), X-ray diffractometer (XRD), transmission electron microscope (TEM) and PL spectrum. The nanorods were about 100 nm in diameter and more than 1 μm in length, which possessed wurtzite structure with a c axis growth direction. The room-temperature PL measurement of the nanorod arrays showed strong ultraviolet emission. The effect of the crystal structure and the thickness of TiO₂ films on the morphologies of ZnO nanostructures were investigated. It was found that the rutile TiO₂ films were appropriate to the oriented growth of ZnO nanorod arrays in comparison with anatase TiO₂ films. Moreover, flakelike ZnO nanostructures were obtained with increasing the thickness of anatase TiO₂ films.     

Large-scale synthesis of Ag<Subscript>1.8</Subscript>Mn<Subscript>8</Subscript>O<Subscript>16</Subscript> nanorods and their electrochemical lithium-storage properties

Ag_1.8Mn₈O₁₆ nanorods have been synthesized on a large scale by a facile hydrothermal route. The effects of experimental conditions including reaction time and reactant concentration on the phase and morphology of the final products were investigated systematically. The products were characterized by using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and energy-dispersive X-ray (EDX) spectroscopy. Electrochemical lithium-storage capabilities of the as-formed nanostructured Ag_1.8Mn₈O₁₆ were also evaluated. Interestingly, the as-formed Ag_1.8Mn₈O₁₆ nanorods possess the unique one-dimensional structure and in situ silver loading, which are beneficial features for electrochemical lithium-storage applications. The results suggest their potential use as cathode materials for lithium-ion batteries.     

Synthesis and characterization of single crystalline SnO<Subscript>2</Subscript> nanorods by high-pressure pulsed laser deposition

Tin oxide (SnO₂) nanorods were grown by high-pressure pulsed laser deposition (PLD). The nanorods were grown without the use of a catalyst but required high background pressure growth in order to realize small grain columnar growth and nanorod formation, with nanorod formation most favored on non-epitaxial substrates. The structures and morphology were characterized by field emission scanning electron microscopy (FESEM) and high resolution transmission electron microscopy (HRTEM). X-ray diffraction and HRTEM analysis indicate that the as-grown SnO₂ nanorods are single crystals with a rutile structure. The nanorods are approximately 50–90 nm in diameters and 1.5 μm in length. This method provides an approach for large area synthesis of one dimensional SnO₂ nanostructure materials. PACS 81.16.Mk; 61.46.-w; 81.07.-b     

Novel CeO<Subscript>2</Subscript> nanorod framework prepared by dealloying for supercapacitors applications

The CeO₂ nanorod framework was synthesized via a facile-dealloying method coupled with calcination treatment for supercapacitors. X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) characterizations identified the cubic phase and nanorod morphology of the synthesized sample. Their electrochemical performance was also evaluated by cyclic voltammetry, galvanostatic charge-discharge tests, and cycling performances. The results show that CeO₂ nanorod framework possesses high-specific capacitance and superior charge/discharge stability, which are mainly ascribed to its high-Brunauer-Emmett-Tellar surface area (110.6 m² g^?1). Notably, the CeO₂//AC (Active Carbon) asymmetric supercapacitor device exhibits excellent cycling stability with capacity retention of 133.6% after cycling for 30,000 cycles.     

Synthesis of single crystalline layered lithium manganese oxide nanorods

Single-crystalline layered lithium manganese oxide nanorods were prepared via a low-temperature molten salt synthesis method. The material was investigated by a variety of techniques, including X-ray powder diffraction (XRD), transmission electron microscopy (TEM), and X-ray photoelectron spectrum (XPS).     

Submicron Li<Subscript>2</Subscript>MoO<Subscript>4</Subscript> material prepared by rheological phase method and its evaluation of lithium storage performances

In this paper, submicron Li₂MoO₄ material was synthesized via rheological phase method. The structure, composition and morphology of the obtained powders were characterized by X-ray diffraction (XRD), X-ray photoelectron spectrometer (XPS) and scanning electron microscope (SEM), respectively. The key calcination temperature was 700 ^oC. The particle sizes were about from 100 to 300 nm. As anode material of lithium ion batteries, lithium storage performances of the as-prepared Li₂MoO₄ were evaluated at different current densities. The best capacity retention was 75.7% of the initial capacity (592.13 mAh g^-1) after 50 cycles at 0.2 mA cm^-2 in 0.1-2.5 V, and the resistance was about 123.5 Ω, indicating a potential prospect in the application of lithium ions batteries.     

Synthesis of nanorods FePO4 via a facile route

Iron phosphate nanorods were synthesized via a novel facile route. The structure, composition, and morphology of the prepared material were characterized by X-ray diffraction (XRD) and transmission electron microscope (TEM), respectively. The diffraction lines were indexed to the hexagonal structure. The diameter of these nanorods is about in the range of 20–30 nm and the length 50–100 nm. The preferential growth direction of the prepared material was the [100]. The reaction mechanism for the synthesis of FePO₄ nanorods was also primarily discussed. Compared to the bulky and the irregular nanoparticles, the nanometer ones will be more fascinating for application in many areas.     

Two-phase reaction mechanism during chemical lithium insertion into α-MoO<Subscript>3</Subscript>

The phase transition during chemical lithium insertion into α-MoO₃ was investigated by chemical analysis, X-ray diffraction (XRD) and electrochemical characterisation. The samples have been prepared by reaction of various amounts of water-free lithium iodide with fine-particulate orthorhombic molybdenum trioxide in n-hexane (non-aqueous media), which yielded materials with different Li/Mo ratio. XRD investigations of these materials proved that the crystal structure of the layered α-MoO₃ has been changed after the chemical lithiation. The phase transition ranged from 0.25 < x < 0.5 in Li _x MoO₃ upon chemical lithium insertion into α-MoO₃. The XRD lines of lithium inserted phase Li _x MoO₃ grew at the expense of the XRD lines of the pristine α-MoO₃ as lithium ions were chemically inserted until the disappearance of lines related to α-MoO₃. The electrochemical performance of the lithiated samples is improved in comparison with the starting material (non-lithiated α-MoO₃).     

Facile synthesis of Nb2O5 nanorod array films and their electrochemical properties

Nb₂O₅ nanorod array films were synthesized by a facile hydrothermal process using niobium metal foil and NH₄F as precursors. The Nb₂O₅ nanorods stand on the niobium metal foil substrate and are less than 100 nm in diameter and about 1 μm in length. X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM) characterizations indicate that these nanorods have orthorhombic structure and grew longitudinally along 〈0 0 1〉 direction. The nanorod growth mechanism was discussed. Thermal annealing at a temperature below 500 °C did not change the microstructure of nanorods but improve the crystallinity. The Nb₂O₅ nanorod array films have been tested as cathode material for lithium battery, which showed a good specific capacity up to 380 mAh g⁻¹ even after 50 charge/discharge cycles.     

Growth of ZnO nanorods by aqueous solution method with electrodeposited ZnO seed layers

ZnO nanorod arrays on ZnO-coated seed layers were fabricated by aqueous solution method using zinc nitrate and hexamethylenetetramine at low temperature. The seed layers were coated on ITO substrates by electrochemical deposition technique, and their textures were dominated by controlling the deposition parameters, such as deposition potential and electrolyte concentration. The effects of the electrodeposited seed layers and the growing parameters on the structures and properties of ZnO nanorod arrays were primarily discussed. The orientation and morphology of both the seed layer and successive nanorods were analyzed by using X-ray diffraction (XRD), SEM and TEM. The results show that the seed layer deposited at −700 mV has evenly distributed crystallites and (0 0 2) preferred orientation; the density of resultant nanorods is high and ZnO nanorods stand completely perpendicular onto substrates. Meanwhile, the size of nanorods quite also depends on the growth solution, and the higher concentration of growth solution primary leads to a large diameter of the ZnO nanorods.     

Preparation and characterization of SrSnO3 nanorods

Perovskite strontium stannate (SrSnO₃) nanorods were prepared by annealing the precursor SnSr(OH)₆ nanorods at 600 °C for 3 h. The precursor nanorods were hydrothermally synthesized at 160 °C for 16 h using Sr(NO₃)₂ and SnCl₄·5H₂O as starting materials in the presence of surfactant cetyltrimethyl ammonium bromide (CTAB). As-prepared samples were characterized by X-ray diffraction (XRD), thermogravimetric-differential thermal analysis (TG-DTA), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and infrared ray spectroscopy (IR). The results show that the as-synthesized powders are made of SrSnO₃ one-dimensional nanorods of about 0.2-1 μm length and 100-150 nm diameter. Possible formation mechanism of SrSnO₃ with nanorod structure under certain conditions was preliminarily analyzed, in which it was thought that CTAB played an important role in the formation process of the nanorod structure. Electrochemical performance of the samples versus Li metal was also evaluated for possible use in lithium-ion batteries.     

Synthesis and nanostructural investigation of TiO<Subscript>2</Subscript> nanorods doped by SiO<Subscript>2</Subscript>

TiO₂ Nano rods can be used as dye-sensitized solar cells, various sensors and photocatalysts. These nanorods are synthesized by a hydrothermal corrosion process in NaOH solution at 200°C using TiO₂ powder as the source material. In the present work, the synthesis of TiO₂ nanorods in anatase, rutile and Ti₇O₁₃ phases and synthesis of TiO₂ nanorods by incorporating SiO₂ dopant, using the sol–gel method and alkaline corrosion are reported. The morphologies and crystal structures of the TiO₂ nanorods are characterized using field emission scanning electron microscopy (FE-SEM), atomic force microscopy (AFM) and X-ray diffraction (XRD) study. The obtained results show not only an aggregation structure at high calcination temperatures with spherical particles but also Ti–O–Si bonds having four-fold coordination with oxygen in SiO^4 −.     

Synthesis of aligned GaN nanorods on Si (111) by molecular beam epitaxy

Straight and well-aligned GaN nanorods have been successfully synthesized by molecular beam epitaxy (MBE) method. The GaN nanorods have been characterized by field-emission scanning electron microscopy (FE-SEM) equipped with energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), transmission electron microscopy (TEM) and selected area electron diffraction (SAED). SEM images show that GaN nanorods are constituted with two parts of which shapes are different from each other. The upper part of the nanorod is very thin and its lower part is relatively thick. The XRD and EDS analysis have identified that the nanorods are pure hexagonal GaN with single crystalline wurtzite structure. The TEM images indicate that the nanorods are well crystallized and nearly free from defects. The XRD, HRTEM, and SAED pattern reveal that the growth direction of GaN nanorods is 〈0001〉. The photoluminescence (PL) spectra indicate the good emission property for the nanorods. Finally, we have demonstrated about the two-step growth of the nanorods. PACS 81.07.Bc; 81.05.Ea; 81.15.Hi     

Hexagonal nanorods of tungsten trioxide: Synthesis, structure, electrochemical properties and activity as supporting material in electrocatalysis

Tungsten trioxide, unhydrated with hexagonal structure (h-WO₃), has been prepared by hydrothermal method at a temperature of 180 °C in acidified sodium tungstate solution. Thus prepared h-WO₃ has been characterized by X-ray diffraction (XRD) method and using electrochemical techniques. The morphology has been examined by scanning and transmission electron microscopies (SEM and TEM) and it is consistent with existence of nanorods of 50-70 nm diameter and up to 5 μm length. Cyclic voltammetric characterization of thin films of h-WO₃ nanorods has revealed reversible redox behaviour with charge-discharge cycling corresponding to the reversible lithium intercalation/deintercalation into the crystal lattice of the h-WO₃ nanorods. In propylene carbonate containing LiClO₄, two successive redox processes of hexagonal WO₃ nanorods are observed at the scan rate of 50 mV/s. Such behaviour shall be attributed to the presence of at least two W atoms of different surroundings in the lattice structure of h-WO₃ nanorods. On the other hand, in aqueous LiClO₄ solution, only one redox process is observed at the scan rate of 10 mV/s. The above observations can be explained in terms of differences in the diffusion of ions inside two types of channel cavities existing in the structure of the h-WO₃ nanorods. Moreover, the material can be applied as active support for the catalytic bi-metallic Pt-Ru nanoparticles during electrooxidation of ethanol in acid medium (0.5 mol dm⁻³ H₂SO₄).     

Preparation and characterization of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> nanorod by low heating solid state coordination method

Cathode material LiMn₂O₄ nanorod was prepared by annealing of the mixed precursor which was synthesized by low heating solid state coordination method using lithium acetate, manganese acetate and oxalic acid as starting materials. The structures and morphologies of the LiMn₂O₄ nanorod were investigated as a function of annealing temperature and time. The results showed that all samples in different annealing temperatures and time have the same spinel structure. The higher the annealing temperature is, the more complete the crystal structure forms, and the larger the particle size is. In addition, the electrochemical properties of the LiMn₂O₄nanorod were studied in this paper.     

Polymethylmethacrylate/Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> composite nanofiber membranes with ultra-low dielectric permittivity

Ultra-low dielectric permittivity poly (methyl methacrylate)/Fe₃O₄ composite fiber membranes have been successfully prepared using electrospinning. The composite membranes were characterized by SEM (scanning electron microscopy), TEM (transmission electron microscopy), FT-IR (Fourier transform infrared), XRD (X-ray diffraction) and a radio frequency (RF) impedance/capacitance material analyzer. The magnetic measurement showed that the composite membranes displayed the super-paramagnetic property. The results showed that the dielectric permittivity of the composite fiber membranes was decreasing with increasing Fe₃O₄ nanoparticle content.     

Synthesis of SnO<Subscript>2</Subscript> tubular nanostructures on top of a silicon nitride surface using polymeric templates and their characterization as gas sensor

Uniform polycrystalline SnO₂ microtubes formed by sintered nanoparticles (fixed to a surface or in free standing form) were obtained with the infiltration technique using SnCl₄ as precursor and a porous polycarbonate (PC) film as template. The advantage of this synthesis method was based on its simplicity, reproducibility, low cost, and the possible applicability to other complex oxides. The morphology and crystal structure of SnO₂ tubes were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). The crystalline sizes of the nanoparticles assembled in the tube walls obtained at 600 °C were in the range of 5–7 nm, calculated from both the XRD and the TEM data. The length of the microtubes fixed to a silicon nitride surface ranged between 2 and 7 μm. Sensors fabricated with this material showed unusual sensitivity to ethanol at room temperature and fast reversible response, as compared to those obtained by the deposition of metallic tin film and further oxidation (Rheotaxial Growth and Thermal Oxidation method).     

Hydrothermal synthesis of CeF<Subscript>3</Subscript> nanocrystals and characterization

CeF₃ nanocrystals with plate-like and perforated morphologies were successfully synthesized via a facile hydrothermal route. The nanocrystals of CeF₃@silica can dispersed in aqueous solution were also prepared. The effects of fluoride sources on the morphology and microstructure of the nanocrystals were investigated by means of transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), and powder X-ray diffraction (XRD). Results indicate that the morphology of the rare earth compound nanocrystals can be well tuned by selecting proper fluoride sources. The ultraviolet (UV) absorption peak of the CeF₃ nanocrystals is slightly blue shifted along with the decrease of size. And the photoluminescence (PL) intensity of the CeF₃ nanocrystals is closely related to size and microstructure as well.