2-乙基己基膦酸2-乙基己基酯钠皂微乳液

HA( 2-乙基己基膦酸 2-乙基己基酯 )是一种性能优良的萃取剂,经皂化形成微乳液后,能大大提高萃取率 .许多学者对含有中长链醇等助表面活性剂的 HA碱皂微乳液的物理化学性质进行了深入的研究 [1－ 4].　　本文报导了用 NaOH皂化不含任何助表面活性剂的 HA煤油溶液,当体系中的 NaOH与 HA数量比达到一定值时,会形成稳定的 W/O型微乳液 .不同的 nNaOH:nHA形成的微乳液的状态可能有所不同 .对这种不含助表面活性剂的微乳液的相行为、电导、溶水量等物理化学性质进行了初步研究 .1实验部分 （ 1） 仪器和试剂 DDS-11A型电导率仪,上…     

萃取剂HDEHP界面性质研究

萃取剂ＨＤＥＨＰ界面性质研究孙国新，杨永会，孙思修，沈静兰（山东大学化学系，济南，２５０１００）关键词界面性质，二－（２－乙基己基）磷酸，萃取剂二－（２－乙基己基）磷酸（ＨＤＥＨＰ）是应用十分广泛的萃取剂，其萃取金属的热力学及动力学研究均有大量报道［...     

2－乙基己基膦酸单（2－乙基己基）酯从盐酸溶液中萃取Ga（Ⅲ）的机理

２－乙基己基膦酸单（２－乙基己基）酯从盐酸溶液中萃取Ｇａ（Ⅲ）的机理赵经贵，邢美君，刘宏（黑龙江大学化学系哈尔滨１５００８０）关键词溶剂萃取，镓，乙基己基膦酸单（乙基己基）酯２－乙基己基膦酸单（２－乙基己基）酯（Ｐ５０７，ＥＨＰ）在稀有元素、有色金属...     

二(2-乙基己基)磷酸对氨基酸的萃取平衡

二（２－乙基己基）磷酸对氨基酸的萃取平衡曹汉瑾,王德宝,刘沛妍,吴子生,严忠（东北师范大学化学系,长春,１３００２４）关键词氨基酸,二（２－乙基己基）磷酸,萃取平衡,分配比迄今为止,有关氨基酸溶剂萃取的文献报道还不多［１～３］．本实验以二（２－乙基己...     

共聚型2-乙基己基膦酸单2-乙基己基酯萃淋树脂孔结构与分离效能的关系

应用性能优良的２－乙基己基膦酸单２－乙基已基酯ＨＥＨ（ＥＨＰ）萃取剂，首次制备了一系列不同孔结构的萃淋树脂，针对难以分离的镧系元素中最难分离的镨、钕，研究了孔结构等与分离效能之关系，探寻出最适宜的孔结构。其比表面积Ｓ为 ２０９ ｍ２／ｇ，平均孔径为 ７．７ｎｍ，孔体积Ｖｇ ０．４０１ｍＬ／ｇ；ＨＥＨ（ＥＨＰ）最适宜量为４６．５％，从而达到最佳分离。     

两相滴定法研究2-乙基己基膦酸单2-乙基己基酯从盐酸介质中萃取钕(Ⅲ)的动力学

本文利用两相滴定法作为分析手段,用恒界面池搅拌法考察了多种因素对2-乙基己基膦酸单2-乙基己基酯(HEHEHP,HA)从盐酸介质中萃取Nd(Ⅲ)动力学的影响,从实验结果推论出萃取过程为界面化学反应控制型机理。     

气相色谱-串联质谱法测定食用油中两种非邻苯二甲酸酯类增塑剂

建立了气相色谱-串联质谱同时测定食用油中对苯二甲酸二（2-乙基己基）酯和偏苯三甲酸三（2-乙基己基）酯两种非邻苯二甲酸酯类增塑剂的方法。样品采用乙腈提取,于-20℃冷冻除脂净化,用气相色谱-串联质谱选择反应监测模式测定。两种化合物的检出限为0.03 mg/kg,定量限为0.1 mg/kg,线性范围为0.1~10 mg/kg。3个添加水平（0.1、0.3和1.0 mg/kg）下的回收率为81.04%~108.31%,相对标准偏差为0.70%~9.91%。该方法简便、准确,适用于食用油中对苯二甲酸二（2-乙基己基）酯和偏苯三甲酸三（2-乙基己基）酯的检测。     

钾皂化HEHPEHE的谱学性质及微乳液的形成

运用傅立叶变换红外光谱研究了钾皂化2－乙基已基磷酸单2－乙基巴基酯（简称HEHPEHE或P507）的性质，同时配合激光光散射技术研究皂化应对形成微乳液性能的影响．红外光谱的研究表明，皂化度（αs）超过60％时，（K，H）EHPEHE呈现酸盐体系的特殊性质，体系对水的增溶能力迅速增大，该体系开始具有形成微乳液的能力；αs为75％左右时，体系对水的增溶能力最强；大于75％时，随着皂化度的继续增加，体系对水的加溶能力迅速下降．激光光散射的实验结果表明，αs为75％时，微乳体系中的平均液滴半径达到最大值（103.8nm）。红外光谱的结果证明形成微乳液对HEHPEHE分子中的P－O－C、P＝O和P－O－H均与水分子有不同程度的相互作用．     

二—（2—乙基己基聚氧化烯烃）琥珀酸双酯磺酸钠的表面活性及应用

二－（２－乙基己基聚氧化烯烃）琥珀酸双酯磺酸钠的表面活性及应用姚传义吴金川何志敏＊（天津大学化学工程研究所天津３０００７２）关键词二－（２－乙基己基聚氧化烯烃）琥珀酸双酯磺酸钠，表面活性，反胶团酶反应，橄榄油水解１９９７－０９－１９收稿，１９９７－１...     

稀释剂对二（2—乙基己基）磷酸萃取镧（Ⅲ）的影响

二（２－乙基己基）磷酸从硝酸介质中对Ｌａ（Ⅲ）的萃取对不同稀释剂其平衡常数为；正己烷＞环己烷＞四氯化碳＞甲苯＞氯仿＞甲异丁酮，萃取平衡常数与稀释剂的极性参数Ｓ间呈线性关系。     

Effects of Mixed Anionic-Cationic Surfactants and Alcohol on Solubilization of Water-in-oil Microemulsions

The solubilization of water in w/o microemulsions formed with mixed-surfactants containing one anionic and one cationic surfactant and alcohol was studied as a function of alkyl chain length of oil (C6 to C16), mixed-surfactant (sodium dodecyl sulfate, SDS, and cetyltrimethylammonium bromide, CTAB, or cetylpyridinium bromide CPB), and alcohol (1-butanol, 1-pentanol, 1-hexanol). The results show that the solubilization of water in microemulsion systems increases significantly with the mixed-surfactants due to the synergistic effect resulting from the strong Coulombic interactions between cationic and anionic surfactants and the solubilizing efficiency increases as the chain length or concentration of alcohol increases. With increasing the oil chain length the solubilization for water increases, decreases, and has the chain length compatibility effect when the systems contain 1-hexanol, 1-butanol, 1-pentanol, respectively. The total solubilizing capacity increases as the surfactant concentration (keep the ratio of SDS to butanol constant) increases.     

Microemulsion electrokinetic chromatography for the analysis of green tea catechins: effect of the cosurfactant on the separation selectivity

Microemulsion electrokinetic chromatography (MEEKC) was applied to the separation of six catechins and caffeine, the major constituents of the green tea. The developed methods involved the use of sodium dodecyl sulfate (SDS) as surfactant, n-heptane as organic solvent and an alcohol as cosurfactant. The separations were performed under acidic conditions (pH 2.5 phosphate buffer, 50 mM) to ensure good stability of the catechins, with reversed polarity (anodic outlet). The effect of the alcohol nature on the MEEKC selectivity was evaluated; nine alcohols were used as cosurfactant: 1-butanol, tert-butanol, 1-pentanol, 2-pentanol, 3-pentanol, cyclopentanol, 1-hexanol, 2-hexanol, and cyclohexanol. The migration order of (+)-catechin (C), (-)-epicatechin (EC), (-)-epigallocatechin (EGC), (-)-gallocatechin (GC), (-)-epigallocatechin gallate (EGCG), (-)-epicatechin gallate (ECG), caffeine and theophylline was significantly affected by the alcohol used as cosurfactant. Using nine microemulsions, four different selectivities were achieved: A (cyclohexanol); B (2-pentanol, 3-pentanol, 1-hexanol, 2-hexanol); C (1-butanol, 1-pentanol, cyclopentanol); D (tert-butanol). MEEKC methods, based on 2-hexanol and cyclohexanol as cosurfactant were validated and successfully applied to the analysis of catechins and caffeine in commercial green tea products.     

醇添加对钴基催化剂费托合成反应的影响

在固定床微反应器上利用全产物在线分析方法, 研究了钴基催化剂上伯醇C_nH_2n+1OH (n=2, 3, 5, 6)在惰性气氛(Ar)和氢气气氛下的反应行为以及添加C_nH_2n+1OH对费托(FT)合成反应的影响, 并结合原位漫反射傅里叶变换红外光谱(DRIFTS)表征. 结果表明: 碳数为n的醇在Ar 气氛和H₂气氛下反应主要有脱羰和脱水两条反应路径, 分别生成碳数为n-1的烃和相同碳数的烃. 低碳数醇(乙醇和正丙醇)的添加对费托合成产物分布无明显影响; 而较高碳数的醇(正戊醇, 正己醇)的加入使碳数为n-1以上烃的选择性显著增加, 这是由于C_nH_2n+1OH加入后生成的碳数为n-1和n的中间体可进一步发生链引发反应, 生成更多的长链烃.     

Chiral microemulsion electrokinetic chromatography: Effect of cosurfactant identity on enantioselectivity, methylene selectivity, resolution, and other chromatographic figures of merit

The effect of cosurfactant identity on microemulsion size, elution range, retention factor, enantioselectivity, methylene selectivity, efficiency, and resolution in chiral microemulsion formulations was examined. The chiral surfactant dodecoxycarbonylvaline was used in conjunction with the cosurfactants 1-butanol, 1-pentanol, 2-pentanol, 1-hexanol, 2-hexanol, cyclopentanol, and cyclohexanol. The millimolar concentration of cosurfactant was held constant regardless of identity. Ethyl acetate was incorporated as the microemulsion oil core and the buffer utilized was 50 mM phosphate at a pH of 7.0. In general, secondary alcohols improved enantioselectivities and primary alcohols had the opposite effect, with the exception of the 1-butanol. The trends observed varied slightly depending on analyte. Of the six chiral analytes tested, cyclopentanol provided the best enantioselectivity for three, 1-butanol for two compounds, and 2-pentanol for one analyte. The lowest enantioselectivities were achieved with 1-pentanol or 1-hexanol for all compounds. Methylene selectivity was found to decrease with reductions in alcohol chain length. Among equal carbon number alcohols, methylene selectivity was lower for secondary alcohols. Efficiency and resolution values varied with different cosurfactants and depended on analyte identity.     

Dielectric Study of the Miscibility of Binary Liquids, One Being an Alcohol

A dielectric relaxation study has been made over a frequency range of 10⁶–10^–3 Hz in the supercooled liquid state of the binary mixtures of 2-ethyl-1-hexanol (2EHOH) with a wide variety of common liquids. Differential scanning calorimetry measurements have also been made above 100 K. Our studies show compatibility of the methylcyclohexane with 2EHOH over the entire composition range. However, in the case of 1-bromobutane and acetone with 2EHOH, we have clearly seen two liquidlike phases separating out, which indicates incompatibility. In the case of 4-methyl-2-pentanol, the binary liquid shows no heterogeneity over most of the concentration range. In the case of methyl alcohol (MOH), the binary liquid shows some heterogeneity at a molecular level in the MOH-rich region. An attempt has been made to understand miscibility in terms of the preference for ring and chain formation among the alcohol molecules.     

Enzymatic esterification and phase behavior in ionic microemulsions with different alcohols

The esterification of hexanoic acid and 1-pentanol catalyzed by the lipase fromChromobacterium viscosum was studied at 298.2 K using different Winsor systems as reaction medium. The microemulsion systems consisted of brine and alkane stabilized by the anionic surfactant sodium dodecylsulphate and a short-chained alcohol. The alcohol acts both as a reactant and as a part of the reaction medium. Therefore, it is of great fundamental interest to know the phase behavior of the used microemulsion systems. Partial phase diagrams were determined and the efficiency of different alcohols on the transition from a Winsor I system to a Winsor III or a Winsor IV system with bicontinuous structure and further to a Winsor II system was investigated. The investigated alcohols were 2-methyl-1-propanol, 1-butanol, 2-butanol, 2-methyl-1-butanol, 3-methyl-1-butanol, 1-pentanol, 2-pentanol, 3-pentanol, 2-methyl-1-pentanol, 3-methyl-1-pentanol, 4-methyl-1-pentanol, and 1-hexanol. The aqueous medium consisted of 0.5 m NaCl(aq) or a phosphate buffer (pH=7) and the organic medium of octane or 2,2,4-trimethyl pentane. A long alkyl chain of the alcohol or a branching far from the hydroxyl group gives a more efficient cosurfactant and a transition from Winsor I to Winsor III or Winsor IV at lower alcohol contents. In the Winsor III system the yield of 1-pentyl hexanoate is twice as high as the yield in the bicontinuous Winsor IV system.     

Kinetic model for reactivity in quaternary water-in-oil microemulsions

A study was carried out on the nitrosation of piperazine (PIP) and N-methylbenzylamine (MeBzAm) by N-methyl-N-nitroso-p-toluenesulfonamide (MNTS) in quaternary microemulsions of tetradecyltrimethylammonium bromide (TTABr)/isooctane/alcohol/water, varying the nature and the concentration of the following alcohols: 1-pentanol, 1-hexanol, 1-heptanol, 1-octanol and 1-decanol keeping the [1-alcohol]/[TTABr] = 4 relationship constant. In addition a study was carried out on the influence of the alcohol concentration, working with molar relationships [1-hexanol]/[TTABr]=3, 4 and 5. On the basis of the molar volumes of the alcohol and surfactant and the concentration of alcohol at the interface it was possible to calculate the change in its volume with as varying compositions of the microemulsion. In order to interpret the experimental results a kinetic model was devised which takes into account the distribution of the reactants between the different pseudophases and the change in the volume of the interface. The rate constants at the interface of the microemulsion are lower than in pure water and are independent of the nature of the alcohol used as a cosurfactant and the molar relationship [alcohol]/[TTABr]. This independence indicates that the main role of the cosurfactant is to increase the volume of the interface with the consequent dilution of the reactants.     

Solubility of anthracene in binary toluene + alcohol solvent mixtures at 298.15 K

Experimental solubilities are reported for anthracene in eight binary toluene?+?alcohol solvent mixtures at 298.15?K. The alcohol solvents studied were 1-propanol, 1-butanol, 1-pentanol, 1-hexanol, 2-propanol, 2-butanol, 2-methyl-1-propanol and 3-methyl-1-butanol. Results of these measurements were used to test a mathematical representation based on the combined nearly ideal binary solvent (NIBS)/Redlich–Kister equation. For the eight systems studied, the combined NIBS/Redlich–Kister equation was found to accurately describe the experimental data, with an average absolute deviation between the measured and back-calculated values being approximately ±0.4%.     

Effect of 1-hexanol on the phase behavior of SDS/CTAB/NaBr/H2O system

Abstract

The influence of 1-hexanol on the phase behavior of sodium dodecyl sulfate (SDS)/cetyltrimethyl ammonium bromide (CTAB)/NaBr/H₂O system has been systematically investigated in this paper. The results showed 1-hexanol effectively dissolved the precipitate formed by the CTAB and SDS surfactants, while liquid crystal (LC) and aqueous two phase system (ATPS) were formed in a wider range. When the molar ratio of 1-hexanol to surfactant is higher than 1, the precipitation in the system disappeared completely and was transformed into ATPS and LC, indicating that alcohol inserted at least evenly between every two surfactant molecules and hence effectively weakened the electrostatic interaction between the anionic and cationic surfactants and limited the formation of precipitation. Polarizing microscope (POM) with crossed polarizers was employed to investigate the textures of liquid crystals. It was shown that the existence of lamellar LC was confirmed by “Maltese crosses” textures. Additionally, we showed that the thermal stability of LC was promising. The ATPS and LC regions remained stable and changed slightly when the temperature was increased from 40 to 70?°C. The results indicated that ATPS and LC of the system were quiet resistant to temperature with the addition of 1-hexanol.     

Cloud point measurements of 1-butyl-2,3-dimethylimidazolium tetrafluoroborate with alcohols

Mutual solubility data of imidazolium-based ionic liquid, 1-butyl-2,3-dimethylimidazolium tetrafluoroborate ([bmmim][BF₄]) with the alcohols, 1-propanol, 2-propanol, 1-butanol, 1-pentanol, and 1-hexanol were obtained by a cloud point method. The upper critical solution temperatures of the ionic liquid and alcohol mixtures were determined from the mutual solubility data. The upper critical solution temperature of the binary mixtures gradually increased as the chain length of the alcohol increased. The mutual solubility data of binary systems ([bmmim][BF₄] + alcohols) have been correlated by the original UNIQUAC model as well as the extended and modified form of the UNIQUAC model. The temperature dependence of the mutual solubility data could be represented in terms of the temperature dependence of the binary energy parameters obtained from the correlation. Additionally the influence of water contamination on the ionic liquid mixture was shown experimentally by adding pure water into the binary mixture ([bmmim][BF₄] + 1-butanol).