GF-AAS法和HG-AFS法测定土壤中铅的分析方法比较

为验证土壤中铅的氢化物发生原子荧光光谱法(HG-AFS)的有效性,对3种土壤标准样品(GSS-2,GSS-3及GSS-7)进行测定,同时用国家标准方法GB/T 17141—1997[石墨炉原子吸收光谱法(GF-AAS)]进行比较测定。试验结果表明:两种方法的测定结果均与认定值一致。在精密度、回收率及检出限等方面,HG-AFS法均达到与GF-AAS法相当的水平。但HG-AFS法具有操作简单、分析快速等优势。     

Determination of copper, lead, cadmium, zinc, and iron in calcium fluoride and other fluoride-containing samples by means of direct solid sampling GF-AAS

Direct solid sampling graphite furnace AAS (SS-GF-AAS) provides an advantageous alternative to the conventional AAS which requires wet digestion of the samples. This method is suitable for trace element determination in calcium fluoride and other fluoride-containing samples. Matrix effects were studied by using calibration standards, certified reference materials with different matrices and by means of three-dimensional calibration. 3D calibration is suitable for selection of calibration samples for more reliable analyses. Cu, Pb, Cd, Zn, and Fe were determined by means of calibration with variation of sample weight using certified reference materials and suitable fluoride-containing calibration samples. Received: 25 July 1997 / Revised: 15 December 1997 / Accepted: 20 December 1997     

Determination of copper, lead, cadmium, zinc, and iron in calcium fluoride and other fluoride-containing samples by means of direct solid sampling GF-AAS

Direct solid sampling graphite furnace AAS (SS-GF-AAS) provides an advantageous alternative to the conventional AAS which requires wet digestion of the samples. This method is suitable for trace element determination in calcium fluoride and other fluoride-containing samples. Matrix effects were studied by using calibration standards, certified reference materials with different matrices and by means of three-dimensional calibration. 3D calibration is suitable for selection of calibration samples for more reliable analyses. Cu, Pb, Cd, Zn, and Fe were determined by means of calibration with variation of sample weight using certified reference materials and suitable fluoride-containing calibration samples. Received: 25 July 1997 / Revised: 15 December 1997 / Accepted: 20 December 1997     

Certification of 22 elements in a pure copper (99.5%) sample for spark emission and X-ray fluorescence spectrometry (CRM BAM-376)

 The element contents of Ag, Al, As, Be, Bi, Cd, Co, Cr, Fe, Mg, Mn, Ni, P, Pb, S, Sb, Se, Sn, Te, Ti, Zn and Zr in a pure copper (99.5%) sample (CRM BAM-376) for use in spark emission and X-ray fluorescence spectrometry were certified and the certified values are given. For Si, the certification has not yet been completed, the content of this element will be certified later. The sample was produced and certified in collaboration with the Committee of Chemists of the GDMB Gesellschaft für Bergbau, Metallurgie, Rohstoff- und Umwelttechnik. Data of the homogeneity testing and the certification campaign with 14 participating laboratories using different analytical methods are reported. Received: 3 February 1997/Revised: 21 February 1997/Accepted: 5 March 1997     

Influence of storage time and temperature of air-dried soils on pH and extractable nutrients using 0.01 mol/L CaCl2

The stability of pH and certified amounts of nitrate, ammonia, total soluble nitrogen, total soluble organic carbon, magnesium, sodium, potassium and phosphorus obtained by extraction from air-dried (40 °C) soil samples by 0.01 mol/L CaCl₂ solution during storage at –18 °C, 4 °C, ambient temperature, 40 °C and 70 °C was investigated in one calcareous soil and one acid sandy soil. Even at storage times of 45 and 90 days, extractable amounts changed. Extractable amounts of P, NH₄-N, total soluble N and soluble organic C increased even at a storage temperature of 40 °C. The pH was lower for samples stored at a temperature of 70 °C and also the Mg concentration became lower at elevated storage temperatures after 45 days in both soils. It is suggested that reference materials certified for values using unbuffered extractants should be stored at a temperature not higher than 4 °C. Received: 13 May 1997 / Revised: 16 July 1997 / Accepted: 18 July 1997     

Development of porous and dispersed CRM

Porous and finely dispersed certified reference materials (CRM) were certified using the gas adsorption method. The special certification procedure for IUPAC isotherm classification types I, II, and IV is presented for meso- and macroporous materials with special emphasis on specific surface area, specific pore volume and pore width according to standards DIN 66 131, 66 134, and 66 135. Four CRMs (SiO₂, α-Al₂O₃, two transition aluminas) with a macro- and mesopore range are presented. Certification was made on the basis of BCR guidelines in connection with interlaboratory tests (altogether 38 participating laboratories, 44 various gas adsorption apparatus). Received: 25 April 1997 / Revised: 22 August 1997 / Accepted: 28 August 1997     

Reference materials for PAHs in foodstuffs: Results of the certification exercise of two coconut oil reference materials

This certification exercise was the final stage of a stepwise interlaboratory study approach, organized within the SMT-program of the EC, for the development of certified reference materials (CRMs) for the determination of PAHs in foodstuffs. The certification exercise was carried out by thirteen European laboratories using a variety of extraction and clean-up procedures and different analytical procedures. Two different coconut oil materials were certified for their mass fractions of six selected PAHs. Received: 25 May 1997 / Revised: 5 September 1997 / Accepted: 28 September 1997     

Efficiency of decomposition procedures for the determination of some elements in soils by atomic spectroscopic methods

Nine decomposition procedures for soil samples, such as via acid mixtures and fusion in open systems and microwave and autoclave dissolution (in closed systems under elevated temperature and pressure) were assessed using certified soil reference materials. The determination of various elements in solutions was performed by FAAS and ICP-OES and the results were compared with certified values and with direct current arc OES analysis.     

ICP-MS – A powerful analytical technique for the analysis of traces of Sb, Bi, Pb, Sn and P in steel

The determination of Sb, Bi, Sn, Pb and P in steel using quadrupole- and double-focusing-sector-field-ICP-MS is described. Simple and fast methods for sample preparation were developed with regard to requirements of ICP-MS. Several certified steel reference materials were analyzed in order to verify the accuracy and precision of the applied methods. Received: 22 April 1997 / Revised: 19 June 1997 / Accepted: 23 June 1997     

The effect of sample preparation on metal determination in soil by FAAS

Different methods for the determination of several metals in soils by flame atomic absorption spectrometry (FAAS) were investigated. Different procedures for total dissolution of soil: I – HF+HClO₄, H₃BO₃, HCl digestion (conventional heating), II – HF+HClO₄, H₃BO₃ digestion followed by fusion with LiBO₂ (conventional heating) and III – HF+HCl+HNO₃, H₃BO₃ digestion (microwave heating), as well as a leaching procedure with HNO₃+HClO₄, HCl were tested and compared. For quality assessment, the certified reference material S-1 soil was used. For most of the investigated metals, the best accuracy and precision were achieved when the procedure I or III were used. The developed procedure was applied to the analysis of soil samples from crude oil refinery and dump of petroleum origin wastes regions. Received: 22 Dezember 1997 / Revised: 9 February 1998 / Accepted: 12 February 1998     

Chlorobiphenyls in sewage sludge; comparison of extraction methods

Six extraction methods for the analysis of PCBs (CB-28, CB-52, CB-101, CB-118, CB-138, CB-153 and CB-180) in sewage sludge were tested. A certified reference material (CRM 392) was used for the evaluation of the performance of the methods. Soxhlet-Dean-Starch with toluene as solvent, Soxhlet with hexane:acetone (2:3), cold digestion/saponification with 2 mol/L KOH in methanol followed by partition with hexane, and sonicated liquid-solid extraction with hexane:acetone (1:1) produced accurate results (97%, 93%, 104%, and 88%, respectively) with acceptable precisions (6.2%, 6.8%, 15% and 12%, respectively). Results in close agreement with the certified value for all congeners were obtained by treatment with BF₃-methanol prior to partition with dichloromethane. However, this is a tedious procedure and involves the use of hazardous compounds. Cyclic steam distillation produced results with an accuracy of around 80% and a good precision (5.2%). The very low consumption of solvents and other expensive chemicals by this technique and the possibility of analyzing the extract directly without clean-up make it an interesting alternative to the more sophisticated methods. Column elution with dichloromethane was found to be less efficient (61%), but it is a rapid, direct method with a low consumption of solvents and it may therefore serve as screening method. Received: 29 April 1997 / Revised: 30 July 1997 / Accepted: 6 August 1997     

Chlorobiphenyls in sewage sludge; comparison of extraction methods

Six extraction methods for the analysis of PCBs (CB-28, CB-52, CB-101, CB-118, CB-138, CB-153 and CB-180) in sewage sludge were tested. A certified reference material (CRM 392) was used for the evaluation of the performance of the methods. Soxhlet-Dean-Starch with toluene as solvent, Soxhlet with hexane:acetone (2:3), cold digestion/saponification with 2 mol/L KOH in methanol followed by partition with hexane, and sonicated liquid-solid extraction with hexane:acetone (1:1) produced accurate results (97%, 93%, 104%, and 88%, respectively) with acceptable precisions (6.2%, 6.8%, 15% and 12%, respectively). Results in close agreement with the certified value for all congeners were obtained by treatment with BF₃-methanol prior to partition with dichloromethane. However, this is a tedious procedure and involves the use of hazardous compounds. Cyclic steam distillation produced results with an accuracy of around 80% and a good precision (5.2%). The very low consumption of solvents and other expensive chemicals by this technique and the possibility of analyzing the extract directly without clean-up make it an interesting alternative to the more sophisticated methods. Column elution with dichloromethane was found to be less efficient (61%), but it is a rapid, direct method with a low consumption of solvents and it may therefore serve as screening method. Received: 29 April 1997 / Revised: 30 July 1997 / Accepted: 6 August 1997     

Optimization of digestion methods for sewage sludge using the Plackett-Burman saturated design

The Plackett-Burman saturated factorial design was used to select optimized dissolution conditions for sewage sludge samples. Three different digestion methods were applied: i) microwave oven digestion in a domestic oven with Parr-type reactors; ii) microwave oven digestion with controlled-pressure reactors; iii) pressure bomb reactor heated on a hot plate. The three methods were validated by statistically comparing the metal contents found with the certified ones of the sewage sludge sample (BCR 145R). No significant differences were obtained and the RSD values were lower than 3% in all cases. The metals were determined by flame-AAS. The variables studied were the following: microwave power; digestion time; predigestion; volume of hydrochloric acid; volume of hydrofluoric acid; volume of nitric acid. The operative advantages offered by microwave digestion with controlled-pressure reactors were also considered. Received: 23 July 1997 / Revised: 31 October 1997 / Accepted: 5 November 1997     

Optimization of digestion methods for sewage sludge using the Plackett-Burman saturated design

The Plackett-Burman saturated factorial design was used to select optimized dissolution conditions for sewage sludge samples. Three different digestion methods were applied: i) microwave oven digestion in a domestic oven with Parr-type reactors; ii) microwave oven digestion with controlled-pressure reactors; iii) pressure bomb reactor heated on a hot plate. The three methods were validated by statistically comparing the metal contents found with the certified ones of the sewage sludge sample (BCR 145R). No significant differences were obtained and the RSD values were lower than 3% in all cases. The metals were determined by flame-AAS. The variables studied were the following: microwave power; digestion time; predigestion; volume of hydrochloric acid; volume of hydrofluoric acid; volume of nitric acid. The operative advantages offered by microwave digestion with controlled-pressure reactors were also considered. Received: 23 July 1997 / Revised: 31 October 1997 / Accepted: 5 November 1997     

Production and certification of environmental reference materials in Romania

Preparation techniques for single-element and multielement standard solutions, with special emphasis on the potential progress in this field are presented. A short review of locally available reference materials is given. Some aspects of the experience accumulated in Romania regarding the various certification approaches of reference materials are presented and the main characteristics of these certified reference materials are listed. Received: 23 May 1997 / Revised: 15 August 1997 / Accepted: 15 August 1997     

Sequential determination of tin, arsenic, bismuth and antimony in marine sediment material by inductively coupled plasma atomic emission spectrometry using a small concentric hydride generator and L-cysteine as prereductant

A hydride generation system using a small concentric hydride generator combined with inductively coupled plasma atomic emission spectrometry (ICP-AES) was established to determine tin, arsenic, bismuth and antimony in a marine sediment material with L-cysteine as a pre-reductant. Influences of concentrations of three kinds of acids (HCl, HNO₃ and HClO₄), L-cysteine, and sodium tetrahydroborate(III) as well as sodium hydroxide were investigated. The interferences from transition ions were found to be insignificant for determination of the four elements in presence of L-cysteine. Under optimized conditions the detection limits were 0.6 ng/mL for arsenic(III), 0.8 ng/mL for antimony(III), 1.7 ng/mL for tin(IV), and 1.2 ng/mL for bismuth(III). The method was applied to determine the four elements in standard marine sediment materials and the results were in agreement with certified values. Received: 4 September 1997 / Revised: 14 October 1997 / Accepted: 7 November 1997     

Estimation of tungsten in complex matrices using toluene 3,4-dithiol and thiocyanate

 A rapid less labour-intensive procedure for complete decomposition of tungsten bearing complex matrices by potassium pyrosulphate and its determination using toluene 3,4-dithiol and thiocyanate is reported. The analytical results of various standard reference materials are presented (Jasperoid GXR-1, Deposit GXR-3, copper mill head GXR-4, tin-tungsten ore IGS-26, Mo-W ore IGS-27, tungsten concentrate SRM-277, scheelite ore SRM-2430, reference tungsten ore TLG-1, CT-1, BH-1 and Mo-W ore MP-2) along with two manganese nodules (GSPN-2 and GSPN-3) recently introduced by the Chinese Academy of Geological Sciences and one Polish soil sample (SRM-2710). For most of the samples the agreement between the observed value and the published data have been found to be extremely good. Derivations have been noted in some samples where published concentrations are indicative values only, indicating that more data are still required to upgrade the status from proposed/unspecified to the certified level. Results of various statistical analyses (intermethod comparison, F-test and regression analysis) reveal that the methods are matrix dependent. Separation of tungsten from molybdenum is straightforward, hence can be used for a quality control programme and in the evaluation of reference materials. Received: 30 December 1996 / Revised: 12 March 1997 / Accepted: 15 March 1997     

Definitive method certification of clinical analytes in lyophilized human serum: NIST Standard Reference Material (SRM) 909b

The National Institute of Standards and Technology (NIST) has developed several Standard Reference Materials (SRMs) based on human serum. NIST SRM 909b, Human Serum, is a lyophilized human serum material with concentrations for seven organic and six inorganic analytes at two levels certified solely by definitive methods (DMs). This material provides the vehicle by which high precision, high accuracy measurements made with DMs at NIST can be transferred through the measurement hierarchy to other laboratories. Isotope dilution gas chromatographic-mass spectrometric (GC-IDMS) methods were applied to measure cholesterol, creatinine, glucose, urea, uric acid, triglycerides, and total glycerides. Thermal ionization isotope dilution mass spectrometry (TI-IDMS) was used for determination of lithium, magnesium, potassium, calcium, and chloride. In addition, chloride was determined by coulometry, providing a comparison between two DMs. Sodium, which lacks a stable isotope that would permit isotope dilution mass spectrometric (IDMS) measurement, was determined by gravimetry. SRM 909b includes certified values for total glycerides and triglycerides, which were not certified in the previous lot of this material (SRM 909a). Improvement in uniformity of vial fill weight in the production of SRM 909b resulted in smaller certified uncertainties over previous freeze-dried serum SRMs. Uncertainties at the 99% level of confidence for relative expanded uncertainty (%) for certification of the organic analytes on a mmol/L/g basis ranged from 0.44% for urea (level II) to 5.04% for glucose (level II). (In-house studies have shown glucose to be a relatively unstable analyte in similar lyophilized serum materials, degrading at about 1% per year.) Relative expanded uncertainties (99% C.I.) for certification of inorganic analytes on a mmol/L/g basis ranged from 0.25% for chloride (level I) to 0.49% for magnesium (level II). Received: 30 July 1997 / Revised: 24 October 1997 / Accepted: 31 October 1997     

测定土壤中重金属元素时前处理方法的改进

建立了一种微波消解前处理技术的半消解法消解样品,采用原子吸收光谱法和原子荧光光谱法同时测定土壤中主要重金属元素铜、锌、镉、砷、汞的方法,检测土壤标准物质GSS-3、GSS-5、GSS-20,结果显示测定均值在标准差允许范围内,相对标准偏差小于8.5%(n=4),是土壤重金属元素快速检测的可选方法。     

Micelle formation for improvement of continuous subcritical water extraction of polycyclic aromatic hydrocarbons in soil prior to high-performance liquid chromatography-fluorescence detection

A new method for the extraction-individual separation-determination of polycyclic aromatic hydrocarbons (PAHs) in soil is reported. The method is based on the integration of three steps: continuous subcritical extraction, solid-phase clean-up/preconcentration, and HPLC separation with post-column fluorimetric determination. Sodium dodecyl sulfate (SDS) was added to the water for favouring the extractability of the low-polarity analytes. Soil samples spiked with the target PAHs were subjected to static-dynamic extraction with SDS-water at 50 bar, 150 degrees C, for 15 min of static extraction and 10 min dynamic extraction at a flow-rate of 3 ml/min. Recoveries from 73.6 to 110.4% were obtained in the presence of SDS versus 30 to 80% obtained with water as extractant. The calibration graphs provided by HPLC-fluorimetric detection were run between 0.031 and 0.375 microg/ml for each analyte with regression coefficients between 0.917 and 0.999 and precision, expressed as RSD, between 1.2 and 11.5%. The method was applied to a certified reference material [CRM 524, BCR (Community Bureau of Reference), industrial soil/organic] for validation and the results obtained were in agreement with the certified values.