功能梯度板条的热弹性力学解

本文利用推广后的Mian 和Spencer 功能梯度板理论,研究了功能梯度板条在非均布温度场作用下的热弹性问题．采用该理论中的位移展开公式,在板厚度方向上考虑热传导引起的稳态温度场,材料常数沿板厚方向可以任意连续变化,从而得到了基于弹性理论的功能梯度板条在温度场作用下的解析解．通过数值算例分析,验证了本文理论的正确性并讨论了边界条件和梯度变化程度对功能梯度板条热弹性响应的影响．     

梯度功能材料热弹性应变场分析

本文采用显微数字散斑相关方法，对梯度材料在稳态梯度温度场分布状态下应变场进行了实验与理论计算的研究，并对结果进行了比较与分析，从而为研究、设计、制备梯度功能材料提供了实验方法，并可以梯度材料理论研究的发展提供依据。     

石墨烯增强功能梯度材料板条的热弹性响应

研究了石墨烯增强功能梯度复合材料板条的热弹性问题。基于推广后的Mian和Spencer功能梯度板理论,在板厚度方向上考虑热传导引起的稳态温度场,沿板厚方向考虑了三种石墨烯纳米片的分布形式,最终给出了不同边界条件下石墨烯增强功能梯度板条在温度场作用下的解析解。通过算例分析验证了本文方法的有效性,并讨论了边界条件和石墨烯的分布形式等因素对板条热弹性响应的影响。计算结果表明:石墨烯增强功能梯度材料板条在温度场作用下的热响应与在机械力作用下的弹性响应有较大不同。     

轴对称任意梯度圆筒的弹性动力学解

基于轴对称平面应变问题的运动方程及弹性梯度材料的应力和位移关系,通过将圆筒分层使材料性质离散为分段常数函数,同时在时域内应用有限差分格式,求得了材料性质沿径向梯度变化的圆筒弹性动力学解。本文解不仅适合任意梯度的弹性圆筒,而且容易满足多种形式的初始条件和边界条件。通过对材料性质沿径向为连续函数分布和分段函数分布的梯度圆筒数值分析,并与已有文献结果比较,得出本文解与已有文献的解吻合较好,验证了本文解的正确性和有效性。对材料性质为分段函数的三层组合圆筒分析发现,中间功能梯度层的指数分布因子对圆筒的径向位移和应力随时间变化都会产生显著影响。     

功能梯度材料剪切板屈曲后的自由振动

基于Reddy高阶剪切变形理论和广义K偄rm偄n型方程,对热环境中功能梯度材料剪切板屈曲后的自由振动进行了分析,分析中同时考虑材料热物参数对温度变化的依赖性及热传导.数值算例给出均匀和非均匀温度场中功能梯度材料剪切板在轴向压缩荷载作用下的振动特性,并讨论了材料组分指数、温度场等参数变化所带来的影响.     

与温度相关的非均质圆筒的非线性耦合广义热弹性分析

基于能量守恒方程和L–S广义热弹性理论,借助状态空间技术和Newmark法求解了材料性质沿径向任意梯度分布同时又与温度相关的非均质圆筒非线性耦合广义热弹性问题。通过对材料性质与温度无关和相关功能梯度圆筒的算例分析,给出了在线性和非线性耦合下圆筒内温度和应力沿径向和随时间的变化关系,验证了本文解的正确性和有效性。数值结果表明,考虑材料性质是否与温度相关,能量守恒方程中耦合项是线性还是非线性,得到的温度与应力均存在不同程度的差异。本文解可方便地应用于不同边界条件和初始条件下圆筒的广义热弹性分析。     

一类功能梯度材料表面接触力学研究进展

针对一类杨氏模量梯度变化的功能梯度材料, 考虑摩擦、微动磨损和黏附等因素, 综述了梯度材料有限尺寸、梯度变化规律、梯度涂层厚度、界面摩擦热、压头形状等对表面接触力学性能的影响; 根据不同接触模型中接触界面应力场分布, 分析多种因素影响下功能梯度材料表面抵抗磨损的能力; 最后给出了功能梯度材料接触力学研究中仍存在的主要科学问题及进一步研究展望.      

热流密度/对流换热边界下双向梯度板的瞬态温度场分析

采用有限单元-有限差分法研究了热流密度/对流换热边界条件下双向梯度板的瞬态热传导问题。采用细观力学方法结合混合律准则描述了材料的热物理属性,通过推导一种8节点高阶双向梯度单元建立了结构的连续梯度有限元模型。计算给出了在考虑组份属性的温度效应下,温度场的时间响应历程以及不同时刻温度场的空间分布形式,并与材料属性温度无关时的计算结果进行了比较,最后讨论了相关参数对瞬态温度场的影响规律。结果表明：温度较低时,组份属性的温度效应对瞬态温度场影响很小;在 y 方向热流密度载荷的作用下,温度场沿 x、y 方向均存在明显的梯度;x 方向组份体积分布系数的增大,延长了温度场达到稳态需要的时间,绝对温度梯度沿 x、y 方向均增大,稳态温度场升高;增大 y 方向组份体积分布系数的值,情况相反。     

功能梯度材料热传导问题的近场动力学模型

当材料中存在不连续性缺陷的时候,传统的基于连续介质理论的方法在研究热传导问题时存在诸多不便．我们基于近场动力学方法(Peridynamics)建立了功能梯度材料的热传导模型,并且研究了在温度荷载作用下功能梯度材料的温度场的变化表现．该文概述了PD方法应用于热传导问题时的详细理论基础,描述了其建模思路以及计算体系,给出了使用PD方法模拟结构承受温度荷载时的计算格式,讨论了不同梯度形式对功能梯度材料内热传导的影响．算例结果表明：通过PD模型所得到的温度场与解析解吻合较好,证明了PD方法在分析功能梯度材料热传导行为等问题时的可行性．     

梯度材料二维轴对称问题的弹性解析解

为了研究梯度材料在静荷载下的响应,首先推导出极坐标下轴对称问题的相容方程;再通过选取特殊的应力函数和弹性模量简化该方程,得到了弹性模量呈幂函数形式分布的梯度圆环内、外受均布压力问题的弹性解;在此基础上,引入接触条件,推得均布荷载下双层梯度圆筒和具有梯度界面层的双材料圆筒的弹性解;最后对各解析解进行了算例分析。分析结果表明:对于双层梯度圆筒,材料的梯度分布不改变其应力正负,并能使筒内应力分布更均匀,缓解应力集中;但对于具有梯度界面层的双材料圆筒,并非梯度层厚度越大应力状态越理想,也存在周向正应力虽然更加平均,最大应力值却有所提升的情况。     

Pressure distribution in an elastomer confined by a long thin-walled flexible hollow cylinder under the assumption of a hydrostatic stress state

The stress distribution in a pressurized elastomer confined by a hollow cylinder is of interest in various applications of material testing and manufacturing. A relatively accurate closed form solution for the pressure distribution inside an elastomer confined by a rigid hollow cylinder was presented by Yu et al. (2001). But in many practical applications the assumption of a rigid hollow cylinder is not appropriate, because the cylinder deformations have a significant influence on the stresses inside the elastomer. Thus in this paper a solution for an elastomer confined by a deformable hollow cylinder is derived. Both axial and radial deformations of the hollow cylinder are taken into account, while the bending stiffness of the cylinder wall is neglected, i.e. the cylinder wall is treated according to the membrane theory. The accuracy of the proposed closed form solution is verified by a parametric finite element simulation.     

Elastodynamic solution of a non-homogeneous orthotropic hollow cylinder

A theoretical method for analyzing the axisymmetric plane strain elastodynamic problem of a non-homogeneous orthotropic hollow cylinder is developed. Firstly, a new dependent variable is introduced to rewrite the governing equation, the boundary conditions and the initial conditions. Secondly, a special function is introduced to transform the inhomogeneous boundary conditions to homogeneous ones. By virtue of the orthogonal expansion technique, the equation with respect to the time variable is derived, of which the solution can be obtained. The displacement solution is finally obtained, which can be degenerated in a rather straightforward way into the solution for a homogeneous orthotropic hollow cylinder and isotropic solid cylinder as well as that for a non-homogeneous isotropic hollow cylinder. Using the present method, integral transform can be avoided and it can be used for hollow cylinders with arbitrary thickness and subjected to arbitrary dynamic loads. Numerical results are presented for a non-homogeneous orthotropic hollow cylinder subjected to dynamic internal pressure. The project supported by the National Natural Science Foundation of China (10172075 and 10002016)     

Axisymmetric circumferential internal crack problem of a thick-walled cylinder with inner and outer claddings

The elastostatic axisymmetric problem for a long thick-walled cylinder containing an axisymmetric circumferential internal crack with two claddings is considered. The claddings having different elastic properties than the hollow cylinder are assumed to be bonded to inner and outer wall of the hollow cylinder. The problem is formulated in terms of a singular integral equation of a well known type, the derivative of the crack surface displacement being the density function, using the standard transform technique. By using appropriate quadrature formulas, the integral equation is reduced to a system of linear algebraic equations. This system is solved numerically and the related stress-intensity factors are calculated for the cases of hollow cylinder with two claddings bonded to inner and outer wall of the cylinder, a cladding bonded to inner wall of the cylinder, a cladding bonded to outer wall of the cylinder and no cladding under axial tensile load. The influence of the geometrical configuration, the claddings and internal crack length on the stress-intensity factors is shown graphically.     

Periodic heat conduction with relaxation time in cylindrical geometry

Steady-periodic heat conduction with relaxation time in an infinitely long hollow cylinder is considered. Four boundary value problems, with boundary conditions of the first and of the second kind, are solved analytically. The solution for a solid cylinder with a sinusoidally varying surface temperature is obtained as a special case of a solution found for the hollow cylinder. The effects of the relaxation time on the steady-periodic temperature field are analysed, in details, for a solid cylinder with a sinusoidally varying surface temperature and for a hollow cylinder with a sinusoidally varying heat flux at the inner surface and with a constant temperature at the outer surface. The results show that thermal resonances may occur and suggest that accurate measurements of the relaxation time could be obtained by means of experiments on steady-periodic heat conduction in cylindrical geometry. Received on 15 April 1997     

Elastic analyses of heterogeneous hollow cylinders

Two different kinds of heterogeneous elastic hollow cylinders are studied in the present paper. One is a multi-layered cylinder with different values in different layers for both elastic modulus and Poisson’s ratio. Another is an elastic hollow cylinder with continuously graded material properties. By introducing two recursive algorithms, the extrusion stresses between two neighbor layers in the multi-layered cylinder submitted to uniform pressures on the inner and outer surfaces can be simply determined. Then the exact solutions of the multi-layered structure can be found based on Lamé’s solution. For the hollow cylinder with continuously graded properties, the displacement method is used. Both Whittaker equation and hyper-geometric equation are derived and successfully solved, and then the exact solutions are found. The results obtained in the present paper are compared with the numerical solutions and good agreements are found. At the end of the present paper, some inherent properties of these two different kinds of heterogeneous elastic hollow cylinders are presented and discussed. The results obtained in the present paper are useful in the design and analysis for composites reinforced by unidirectional fiber layers.     

Stress intensity factors of a crack in a composedcircular cylinder

A composed circular cylinder, formed by a core circular cylinder, containing a crackand enclosed by a layered hollow circular cylinder, is investigated in regard to the evaluation ofstress intensity factors. Analytic solutions to the problem are provided, with which the upper andlower bounds of stress intensity factors in a cracked circular cylinder, the stress distribution in alayered hollow circular cylinder, and the stress intensity factors for a crack in the composedcircular cylinder can precisely be determined. Numerical materials, demonstrating the discretevalues of the stress intensity factors, as well as the general pattern according to which the stressintensity factors vary with the material and geometric constants, are presented. The solutions aredeveloped based on a simplified and modified solution to the Hilbert problem, and the matrixpresentation and manipulation of functions and variables, used in the circuit theory.     

A SOLUTION OF COSINE PRESSURES ON A HOLLOW CYLINDER AND THE LIMIT WHEN k→0

A new stress function is found in this paper and then the problems of cosine pressures on a hollow cylinder are solved with the new stress function,which provides the basis for the solution of the problems of space symmetrical deformation of a hollow cylinder.When the pressures do not vary in the axial direction,that is,when k→0,the lame formulae can be deduced.     

Effect of rotation in magneto-thermoelastic transversely isotropic hollow cylinder with three-phase-lag model

This article deals with the various heat source responses in a transversely isotropic hollow cylinder under the purview of three-phase-lag (TPL) generalized thermoelasticity theory. In presence of magnetic field and due to the rotating behavior of the cylinder, the governing equations are redefined for generalized thermoelasticity with thermal time delay. In order to obtain the stress, displacement and temperature field, the field functions are expressed in terms of modified Bessel functions in Laplace transformed domain. When the outer radius of hollow cylinder tends to infinity, the corresponding results are discussed. Finally an appropriate Laplace transform inversion technique is adopted.     

导弹适配器受压及弹射时摩擦力研究

针对导弹适配器的结构特征,分别建立了可压缩橡胶泡沫和不可压橡胶圆筒轴对称平面应变问题有限变形的平衡方程,基于Blatz-Ko应变能函数和三次缩减多项式应变能函数,得到了相应的位移和应力模式;在此基础上求解了适配器受压问题的非线性方程组和导弹发射时适配器所受到的摩擦力.算例分析与有限元数值模拟比较表明:解析解与数值解非常吻合,径向应力在发射筒内外表面误差最大为0.558%,周向应力在粘合面误差最大为0.246%,导弹发射时的最大量纲为一的摩擦力为1.0228.适配器径向应力在材料粘合交界面上最小,在适配器外表面最大,均为压应力;橡胶泡沫和不可压橡胶的周向应力均为压应力,橡胶泡沫的周向应力由内向外变大,不可压橡胶的周向应力由内向外变小.橡胶泡沫的径向受压大于周向受压,不可压橡胶的周向受压大于径向受压.研究不同过盈量对应力和摩擦力的影响表明:过盈量每增加0.0013,橡胶泡沫 层和不可压橡胶层的径向应力约增加0.13,不可压橡胶层的周向应力约增加2.14,而摩擦力约增加0.22.过盈量对不可压橡胶层的周向应力和导弹所受到的摩擦力影响非常大,对橡胶泡沫的径向应力有一定的影响,周向应力变化很小.     

A SOLUTION OF COSINE PRESSURES ON A HOLLOW CYLINDER AND THE LIMIT WHEN k→0

A new stress function is found in this paper and then the problems of cosine pressures on a hollow cylinder are solved with the new stress function, which provides the basis for the solution of the problems of space symmetrical deformation of a hollow cylinder. When the pressures do not vary in the axial direction, that is, when k→0 the lame formulae can be deduced.