Nanocrystalline formation and optical properties of germanium thin films prepared by physical vapor deposition

Amorphous and nanocrystalline germanium thin films were prepared on glass substrates by physical vapor deposition (PVD). The influence of thermal annealing on the characteristics of the Ge thin films has been investigated. X-ray diffraction (XRD) and SEM show amorphous structure of films deposited at room temperature. After thermal annealing, the crystallinity was improved when the annealing temperature increases. The Ge thin films annealed at different temperatures in air were nanocrystalline, having the face-centered cubic structure with preferred orientation along the 〈1 1 1〉 direction. The nanostructural parameters have been evaluated by using a single-order Voigt profile analysis. Moreover, the analysis of the optical transmission and reflection behavior was carried out. The values of direct and indirect band gap energies for amorphous and nanocrystalline phases are 0.86±0.02, 0.65±0.02 and 0.79±0.02, 0.61±0.02 eV, respectively. In addition, the complex optical functions for the wavelength range 600-2200 nm are reported. The refractive index of the nanocrystalline phase drops from 4.80±0.03 to 2.04±0.02, and amorphous phase changes from 5.18±0.03 to 2.42±0.02 for the whole wavelength range. The dielectric functions ε₁ and ε₂ of the deposited films were recorded as a function of wavelength within the range from 600 to 2200 nm.     

Growth, structural and optical properties of non-stoichiometric CuIn(S1−xSex)2 thin films deposited by solution growth technique for photovoltaic application

Polycrystalline thin films of p-CuIn(S_1−xSe_x)₂ have been deposited by a solution growth technique. The deposition parameters such as pH, temperature and time have been optimized. In order to achieve uniformity of thin film, triethanolamine (TEA) has been used. As deposited films have been annealed at 450 °C in air for 5 min. The surface morphology, compositional ratio, structural properties have been studied by SEM, EDAX and XRD technique, respectively. It has been found that films have chalcopyrite structure with the lattice parameters a=5.28 Å and c=11.45 Å at composition x=0.5. The grain size of all composition x measured from SEM and XRD is varied in between 450 and 520 nm. The optical transmittance spectra have been recorded in the range 350-1000 nm. The absorption coefficient has been calculated at the absorption edge for each of the composition x and it is in the range of 10⁴ cm⁻¹. The material shows the direct allowed band gap, which varies from 1.07 to 1.44 eV with change in composition (0≤x≤1.0). These parameters are useful for the photovoltaic application.     

The ferroelectric and ferromagnetic characterization of CoFe2O4/Pb(Mg1/3Nb2/3)O3-PbTiO3 multilayered thin films

The multiferroic (PMN-PT/CFO)_n (n = 1,2) multilayered thin films have been prepared on SiO₂/Si(1 0 0) substrate with LNO as buffer layer via a rf magnetron sputtering method. The structure and surface morphology of multilayered thin films were determined by X-ray diffraction (XRD) and atom force microscopy (AFM), respectively. The smooth, dense and crack-free surface shows the excellent crystal quality with root-mean-square (RMS) roughness only 2.9 nm, and average grain size of CFO thin films on the surface is about 44 nm. The influence of the thin films thickness size, periodicity n and crystallite orientation on their properties including ferroelectric, ferromagnetic properties in the (PMN-PT/CFO)_n multilayered thin films were investigated. For multilayered thin films with n = 1 and n = 2, the remanent polarization Pr are 17.9 μC/cm² and 9.9 μC/cm²; the coercivity H_c are 1044 Oe and 660 Oe, respectively. In addition, the relative mechanism are also discussed.     

Structural and optical properties of thermal evaporated magnesium phthalocyanine (MgPc) thin films

X-ray powder diffraction (XRD) of MgPc indicated that the material in the powder form is polycrystalline with monoclinic structure. Miller indices, h k l, values for each diffraction peak in XRD spectrum were calculated. Thermal evaporation technique was used to deposit MgPc thin films. The XRD studies were carried out for MgPc thin films where the results confirm the amorphous nature for the as-deposited films. While, polycrystalline films orientated preferentially to (1 0 0) plane with an amorphous background were obtained for films annealed at 623 K for 3 h. Optical properties of MgPc thin films were characterised by using spectrophotometric measurements of transmittance and reflectance in the spectral range from 190 to 2500 nm. The refractive index, n, and the absorption index, k, were calculated. According to the analysis of dispersion curves, the parameters, namely; the optical absorption coefficient (α), molar extinction coefficient (?_molar), oscillator energy (E_os), oscillator strength (f), and electric dipole strength (q²) were also evaluated. The recorded absorption measurements in the UV-vis region show two well defined absorption bands of phthalocyanine molecule; namely the Q-band and the Soret (B-band). The Q-band showed its splitting characteristic (Davydov splitting), and ΔQ was obtained as 0.15 eV. The analysis of the spectral behaviour of the absorption coefficient (α), in the absorption region revealed indirect transitions. The transport and the near onset energy gaps were estimated as respectively 2.74 ± 0.02 and 1.34 ± 0.01 eV.     

Microstructure and electrical properties of Mn-doped barium strontium titanate thin films prepared on copper foils

Ba_0.7−xSr_0.3Mn_xTiO₃ (x = 0, 0.025, 0.05) thin films have been prepared on copper foils using sol-gel method. The films were processed in an atmosphere with low oxygen pressure so that the substrate oxidation is avoided and the formation of the perovskite phase is allowed. XRD and SEM results showed that Mn doping enhanced the crystallization of the perovskite phase in the films. The Mn substitution prevents the reduction of Ti⁴⁺ to Ti³⁺, which is supported by XPS analysis. The Ba_0.7−xSr_0.3Mn_xTiO₃ film with x = 0.025 (BSMT25) exhibits preferred dielectric behavior and a lower leakage current density among the three thin films. The dielectric constant and loss of the BSMT25 film are 1213.5 and 0.065 at 1 MHz and around zero field, which are mostly desired for embedded capacitor applications. The mechanism of Mn doping on improving the electrical properties of barium strontium titanate (BST) thin films was investigated.     

Effect of solution molarity on the characteristics of vanadium pentoxide thin film

Vanadium pentoxide (V₂O₅) thin films have been prepared by spray pyrolysis technique. The influence of solution molarity on the characteristics of the V₂O₅ has been investigated. X-ray diffraction analysis (XRD) showed that, the films deposited at ≥0.1 M were orthorhombic structure with a preferential orientation along 〈0 0 1〉 direction. Moreover, the crystallinity was improved by increasing solution molarity. The microstructure parameters have been evaluated by using a single order Voigt profile method. The optical band gaps, determined by using Tauc plot, have been found to be 2.50 ± 0.02 and 2.33 ± 0.02 eV for the direct and indirect allowed transition, respectively. Also the complex optical constants for the wavelength range 300-2500 nm are reported. At room temperature, the dark conductivity as a function of solution molarity showed the range of 5.74 × 10⁻² ± 0.03 to 3.36 × 10⁻¹ ± 0.02 Ω⁻¹ cm⁻¹. While at high temperature, the behaviour of electrical conductivity dominated by grain boundaries. The values of activation energy and potential barrier height were 0.156 ± 0.011 and 0.263 ± 0.012 eV, respectively.     

Fabrication and characterization of sputtered titanium dioxide films

TiO₂ thin films were prepared under various conditions by using a reactive RF sputtering technique. The structural, optical and electrical characteristics of the films have been investigated. All as-deposited films were amorphous. After annealing at T > 673 K, the crystallinity of the observed tetragonal anatase phase appeared improved. The optical band gap, determined by using Tauc plot, has been found to amount to 3.38 ± 0.03 and 3.21 ± 0.03 eV for the direct and indirect transition, respectively. Also the complex optical constants for the wavelength range 300-2500 nm are reported. Using the two-point probe technique, the dark resistivity has been measured as a function of the film thickness, d. The resistivity, ρ, of the samples has been found to decrease markedly with increasing thickness, but only for d < 100 nm. The behaviour of ρd versus d was found to fit properly with the Fuchs and Sondheimer relation with parameters ρ_o = 4.95 × 10⁶ Ω cm and mean free path, l = 310 ± 2 nm. The log ρ versus 1/T curves show three distinct regions with values for the activation energy of 0.03 ± 0.01, 0.17 ± 0.01 and 0.50 ± 0.02 eV, respectively.     

Study of the structure and electrical properties of the copper nitride thin films deposited by pulsed laser deposition

Copper nitride thin films were prepared on glass and silicon substrates by ablating a copper target at different pressure of nitrogen. The films were characterized in situ by X-ray photoelectron spectroscopy (XPS), Auger electron spectroscopy (AES) and ex situ by X-ray diffraction (XRD). The nitrogen content in the samples, x = [N]/[Cu], changed between 0 and 0.33 for a corresponding variation in nitrogen pressure of 9 × 10⁻² to 1.3 × 10⁻¹ Torr. Using this methodology, it is possible to achieve sub-, over- and stoichiometric films by controlling the nitrogen pressure. The XPS results show that is possible to obtain copper nitride with x = 0.33 (Cu₃N) and x = 0.25 (Cu₄N) when the nitrogen pressure is 1.3 × 10⁻¹ and 5 × 10⁻² Torr, respectively. The lattice constants obtained from XRD results for copper nitride with x = 0.25 is of 3.850 Å and with x = 0.33 have values between 3.810 and 3.830 Å. The electrical properties of the films were studied as a function of the lattice constant. These results show that the electrical resistivity increases when the lattice parameter is decreasing. The electrical resistivity of copper nitride with x = 0.25 was smaller than samples with x = 0.33.     

Enhanced luminescent characteristics of laser-ablated GdVO4:Eu thin films by Li-doping

Li-doping has been used to improve luminescent characteristics of thin films. Influence of Li-doping on the crystallization, surface morphology and luminescent properties of GdVO₄:Eu³⁺ films have been investigated. Crystallinity and surface morphology of thin films have been very important factors to determine luminescent characteristics and depended on the deposition conditions. The GdVO₄:Eu³⁺ and Li-doped GdVO₄:Eu³⁺ thin films have been grown using pulsed laser deposition method on Al₂O₃ (0 0 0 1) substrates at a substrate temperature of 600 °C under an oxygen pressure of 13.33-53.33 Pa. The crystallinity and surface morphology of the films were investigated using X-ray diffraction (XRD) and atomic force microscope (AFM), respectively. A broadband incoherent ultraviolet light source with a dominant excitation wavelength of 310 nm and a luminescence spectrometer have been used to measure photoluminescence spectra at room temperature. The emitted radiation was dominated by the red emission peak at 619 nm radiated from the transition of ⁵D₀-⁷F₂ of Eu³⁺ ions. Particularly, the peak intensity of Li-doped GdVO₄ films was increased by a factor of 1.7 in comparison with that of GdVO₄:Eu³⁺ films. The enhanced luminescence results not only from the improved crystallinity but also from the reduced internal reflections caused by rougher surfaces. The luminescent intensity and surface roughness exhibited similar behavior as a function of oxygen pressure.     

Crystallization and electrical properties of V2O5 thin films prepared by RF sputtering

V₂O₅ thin films were prepared under various conditions by using reactive RF sputtering technique. The microstructure and electrical properties of the films are have been investigated. X-ray diffraction data revealed the films deposited at low O₂/Ar ratio are amorphous. The orthorhombic structure of film improved after post annealing at 873 K. The microstructure parameters (crystallite/domain size and macrostrain) have been evaluated by using a single order Voigt profile method. Using the two-point probe technique, the dark conductivity as a function of the condition parameters such as film thickness, oxygen content and temperature are discussed. It was also found that, the behaviour of ρd versus d was found to fit properly with the Fuchs-Sondheimer relation with the parameters: ρ_o = 2.14 × 10⁷ Ω cm and ?_o = 112 ± 2 nm. At high temperature, the electrical conductivity is dominated by grain boundaries, the values of activation energy and potential barrier height were 0.90 ± 0.02 eV and 0.92 ± 0.02 V, respectively.     

Novel chemical synthetic route and characterization of zinc selenide thin films

Zinc selenide (ZnSe) thin film have been deposited using chemical bath method on non-conducting glass substrate in a tartarate bath containing zinc sulfate, ammonia, hydrazine hydrate, sodium selenosulfate in an aqueous alkaline medium at 333 K. The deposition parameter of the ZnSe thin film is interpreted in the present investigation. The films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), optical absorption, electrical measurements, atomic absorption spectroscopy (AAS). The ZnSe thin layers grown with polycrystalline zinc blende system along with some amorphous phase present in ZnSe film. The direct optical band gap ‘E_g’ for the film was found to be 2.81 eV and electrical conductivity in the order of 10⁻⁸(Ω cm)⁻¹ with n-type conduction mechanism.     

Structural characterization and optical properties of ZnSe thin films

Zinc selenide (ZnSe) thin films (d = 0.11-0.93 μm) were deposited onto glass substrates by the quasi-closed volume technique under vacuum. Their structural characteristics were studied by X-ray diffraction (XRD) and atomic force microscopy (AFM). The experiments showed that the films are polycrystalline and have a zinc blende (cubic) structure. The film crystallites are preferentially oriented with the (1 1 1) planes parallel to the substrate surface. AFM images showed that the films have a grain like surface morphology. The average roughness, R_a = 3.3-6.4 nm, and the root mean square roughness, R_rms = 5.4-11.9 nm, were calculated and found to depend on the film thickness and post-deposition heat treatment.The spectral dependence of the absorption coefficient was determined from transmission spectra, in the range 300-1400 nm.The values of optical bandgap were calculated from the absorption spectra, E_g = 2.6-2.7 eV.The effect of the deposition conditions and post-deposition heat treatment on the structural and optical characteristics was investigated.     

Enhanced field emission from Si doped nanocrystalline AlN thin films

Si doped and undoped nanocrystalline aluminum nitride thin films were deposited on various substrates by direct current sputtering technique. X-ray diffraction analysis confirmed the formation of phase pure hexagonal aluminum nitride with a single peak corresponding to (1 0 0) reflection of AlN with lattice constants, a = 0.3114 nm and c = 0.4986 nm. Energy dispersive analysis of X-rays confirmed the presence of Si in the doped AlN films. Atomic force microscopic studies showed that the average particle size of the film prepared at substrate temperature 200 °C was 9.5 nm, but when 5 at.% Si was incorporated the average particle size increased to ∼21 nm. Field emission study indicated that, with increasing Si doping concentration, the emission characteristics have been improved. The turn-on field (E_to) was 15.0 (±0.7) V/μm, 8.0 (±0.4) V/μm and 7.8 (±0.5) V/μm for undoped, 3 at.% and 5 at.% Si doped AlN films respectively and the maximum current density of 0.27 μA/cm² has been observed for 5 at.% Si doped nanocrystalline AlN film. It was also found that the dielectric properties were highly dependent on Si doping.     

C-V studies on metal-ferroelectric bismuth vanadate (Bi2VO5.5)-semiconductor structure

Ferroelectric bismuth vanadate Bi₂VO_5.5 (BVO) thin films have been successfully grown on p-type Si(100) substrate by using chemical solution decomposition (CSD) technique followed by rapid thermal annealing (RTA). The crystalline nature of the films has been studied by X-ray diffraction (XRD). Atomic force microscopy (AFM) was used to study the microstructure of the films. The dielectric properties of the films were studied. The capacitance-voltage characteristics have been studied in metal-ferroelectric-insulator-semiconductor (MFIS) configuration. The dielectric constant of BVO thin films formed on Si(100) is about 146 measured at a frequency of 100 kHz at room temperature. The capacitance-voltage plot of a Bi₂VO_5.5 MFIS capacitor subjected to a dc polarizing voltages shows a memory window of 1.42 V during a sweep of ±5 V gate bias. The flatband voltage (V_f) shifts towards the positive direction rather than negative direction. This leads to the asymmetric behavior of the C-V curve and decrease in memory window. The oxide trap density at a ramp rate of 0.2 V/s was estimated to be as high as 1.45×10¹² cm⁻².     

Effect of growth parameters on the structure and magnetic properties of thin polycrystalline Fe films fabricated on Si〈1 0 0〉 substrates

This paper deals with the experimental investigation of the structure and magnetic properties of thin polycrystalline Fe films. Two sets of 50 ± 2 nm thick Fe films were fabricated on Si〈1 0 0〉 substrates with native oxides in place by varying (i) the sputter pressure p_Ar and (ii) the Fe sputter power P_Fe. X-ray diffraction (XRD) study revealed that all films grew with strong 〈1 1 0〉 texture normal to the film plane. No higher order peaks were observed in any of the films studied. For both film sets, the lattice constant (a) was less than the bulk Fe lattice constant (a₀ = 2.866 Å), which suggested the existence of compressive strain in all films. Two regions of homogeneous strain were observed over the range of p_Ar studied. Magneto-optical Kerr effect (MOKE) measurements showed that all films exhibited magnetically isotropic behaviour. The magnetic properties were observed to be influenced strongly by p_Ar. The film grown at p_Ar = 4 μbar was the most softest (H_s = 100 ± 8 kA m⁻¹, M_r/M_s = 0.87 ± 0.02) film among all the films studied. The magnetic properties were found to be independent of P_Fe. The effective saturation magnetostriction constant λ_eff determined (using the Villari method) was positive (4 ± 1 ppm) and observed to vary within the calculated error.     

Influences of the iron ion (Fe)-doping on structural and optical properties of nanocrystalline TiO2 thin films prepared by sol-gel spin coating

Titanium dioxide (TiO₂) thin films doping of various iron ion (Fe³⁺) concentrations were deposited on silicon (Si) (100) and quartz substrates by sol-gel Spin Coating technique followed by a thermal treatment at 600 °C. The structure, surface morphology and optical properties, as a function of the doping, have been studied by X-ray diffractometer (XRD), Raman, ultraviolet-visible (UV-vis) and Spectroscopic Ellipsometry (SE). XRD and Raman analyzes of our thin films show that the crystalline phase of TiO₂ thin films comprised only the anatase TiO₂, but the crystallinity decreased when the Fe³⁺ content increased from 0% to 20%. During the Fe³⁺ addition to 20%, the phase of TiO₂ thin film still maintained the amorphous state. The grain size calculated from XRD patterns varies from 29.3 to 22.6 nm. The complex index and the optical band gap (E_g) of the films were determined by the spectroscopic ellipsometry analysis. We have found that the optical band gap decreased with an increasing Fe³⁺ content.     

Ferromagnetism in amorphous Ge1−xMnx grown by low temperature vapor deposition

Magnetic properties of amorphous Ge_1−xMn_x thin films were investigated. The thin films were grown at 373 K on (100) Si wafers by using a thermal evaporator. Growth rate was ∼35 nm/min and average film thickness was around 500 nm. The electrical resistivities of Ge_1−xMn_x thin films are 5.0×10⁻⁴∼100 Ω cm at room temperature and decrease with increasing Mn concentration. Low temperature magnetization characteristics and magnetic hysteresis loops measured at various temperatures show that the amorphous Ge_1−xMn_x thin films are ferromagnetic but the ferromagnetic magnetizations are changing gradually into paramagnetic as increasing temperature. Curie temperature and saturation magnetization vary with Mn concentration. Curie temperature of the deposited films is 80-160 K, and saturation magnetization is 35-100 emu/cc at 5 K. Hall effect measurement at room temperature shows the amorphous Ge_1−xMn_x thin films have p-type carrier and hole densities are in the range from 7×10¹⁷ to 2×10²² cm⁻³.     

Influence of air annealing on the structural, morphological, optical and electrical properties of chemically deposited ZnSe thin films

Zinc selenide nanocrystalline thin films are grown onto amorphous glass substrate from an aqueous alkaline medium, using chemical bath deposition (CBD) method. The ZnSe thin films are annealed in air for 4 h at various temperatures and characterized by structural, morphological, optical and electrical properties. The as-deposited ZnSe film grew with nanocrystalline cubic phase alongwith some amorphous phase present in it. After annealing metastable nanocrystalline cubic phase was transformed into stable polycrystalline hexagonal phase with partial conversion of ZnSe into ZnO. The optical band gap, E_g, of as-deposited film is 2.85 eV and electrical resistivity of the order of 10⁶-10⁷ Ω cm. Depending upon annealing temperature, decrease up to 0.15 eV and 10² Ω cm were observed in the optical band gap, E_g, and electrical resistivity, respectively.     

Chemical bath-deposited ZnS thin films: Preparation and characterization

Chemical bath deposition of ZnS thin films from NH₃/SC(NH₂)₂/ZnSO₄ solutions has been studied. The effect of various process parameters on the growth and the film quality are presented. The influence on the growth rate of solution composition and the structural, optical properties of the ZnS thin films deposited by this method have been studied. The XRF analysis confirmed that volume of oxygen of the as-deposited film is very high. The XRD analysis of as-deposited films shows that the films are cubic ZnS structure. The XRD analysis of annealed films shows the annealed films are cubic ZnS and ZnO mixture structure. Those results confirmed that the as-deposited films have amorphous Zn(OH)₂. SEM studies of the ZnS thin films grown on various growth phases show that ZnS film formed in the none-film phase is discontinuous. ZnS film formed in quasi-linear phase shows a compact and a granular structure with the grain size about 100 nm. There are adsorbed particles on films formed in the saturation phase. Transmission measurement shows that an optical transmittance is about 90% when the wavelength over 500 nm. The band gap (E_g) value of the deposited film is about 3.51 eV.     

Effect of pH value on the structural and magnetic properties of nanocrystalline strontium hexaferrite thin films

Strontium hexaferrite SrFe₁₂O₁₉ thin films have been synthesized at different pH, adjusted by NH₄OH, on the Si (1 0 0) substrate using a spin coating sol-gel process. Fourier transform infrared spectroscopy analysis and theoretical calculations were conducted for determination and controlling metal citrates in solution precursors. X-ray diffraction, scanning electron microscopy and vibrating sample magnetometer were applied to evaluate the composition, microstructure, crystallite size and magnetic properties of the SrFe₁₂O₁₉ thin films. Using the solution with pH 7, the approximately single phase strontium hexaferrite thin films with optimum physical properties can be obtained at calcination temperature of 800 °C. The SrFe₁₂O₁₉ thin films derived from the solution with pH 7 after calcination at 800 °C exhibited crystallite size of 42 nm and magnetic properties of M_s=267 emu/cm³ (at 10 kOe), M_r=134 emu/cm³ and H_c=4290 Oe.