One-step solvothermal preparation of TiO2/C composites and their visible-light photocatalytic activities

Preparation of anatase type titania nanoparticles and their carbon modification were synchronously achieved by the solvothermal method with glycerol as the carbon source. The as-prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and diffuse reflectance spectra (DRS). It was found that the glycerol/ethanol ratio affected significantly the morphology and properties of TiO₂/C composites. The TiO₂/C composite which was obtained in the solution with the glycerol/ethanol ratio of 5/75, contained 1.2 mass% carbon and exhibited both superior adsorption capability and visible-light photocatalytic activity. Contrary to this, samples prepared in the solution with higher glycerol/ethanol ratio, exhibited lower photocatalytic activity similar to that of the titania without carbon modification. It was suggested that excess addition of glycerol might contribute to large amounts of carbonaceous species and severe aggregation of the as-prepared samples, and thus reduced the surface area. As a result, the adsorption capability and visible-light photocatalytic activity increased at first and then decreased with the increase of glycerol addition. Present study provided a facile one-step method to obtain TiO₂/C composites with a controllable carbon content and photocatalytic performance under mild temperature.     

Surface reaction characteristics at low temperature synthesis BaTiO3 particles by barium hydroxide aqueous solution and titanium tetraisopropoxide

Well-crystallized cubic phase BaTiO₃ particles were prepared by heating the mixture of barium hydroxide aqueous solution and titania derived from the hydrolysis of titanium isopropoxide (TTIP) at 328 K, 348 K or 368 K for 24 h. The morphology and size of obtained particles depended on the reaction temperature and the Ba(OH)₂/TTIP molar ratio. By the direct hydrolytic reaction of titanium tetraisopropoxide, the high surface area titania (TiO₂) was obtained. The surface adsorption characteristics of the titania particles had been studied with different electric charges OH⁻ ions or H⁺ ions. The formation mechanism and kinetics of BaTiO₃ were examined by measuring the concentration of [Ba²⁺] ions in the solution during the heating process. The experimental results showed that the heterogeneous nucleation of BaTiO₃ occurred on the titania surface, according to the Avrami's equation.     

An investigation of phase transformation of titania slag using microwave heating

The influences of microwave heating on the phase transformation of titania slag were systematically investigated. The thermal stability, surface chemical functional groups and microstructure of the titania slag before and after microwave heating, at a temperature of 950?°C for 60 min, were also analyzed using thermogravimetry and differential thermal analysis (TG-DSC), Fourier transform infrared spectroscopy (FT-IR) spectrum and scanning electron microscope (SEM), respectively. The TG-DSC analysis revealed that the phase transformation of the titania slag from anatase TiO₂ to rutile TiO₂ occurred between 750 and 1000 °C. The FT-IR rustles demonstrate that the banding form of Ti⁴⁺, Ti³⁺ and Ti²⁺ ions and the methyl groups on the surface of the titania slag has changed and a new chemical bond Ti–OH was formed. The results of SEM showed that a large number of regulation rutile TiO₂ crystals were found on the surface of the microwave-treated samples and the synthetic rutile has been synthesized successfully using microwave heating.     

Characterization and corrosion studies of titania-coated NiTi prepared by sol-gel technique and steam crystallization

Nickel titanium (NiTi) was dip-coated with titania via the sol-gel route using titanium butoxide (Ti(OC₄H₉)₄) as precursor. The as-coated titania film was crystallized to form anatase by treatment in steam at 105 °C. The crystallized film was relatively thick (about 750 nm) and even. Atomic force microscopy (AFM) revealed that the film was dense with a surface roughness of about 3 nm, and was composed of particles of about 100 nm. X-ray diffractometry (XRD) showed that these particles were composed of nanocrystallites of a few nanometers. Nanoindentation tests of the titania film indicated that the film was tough, possibly due to the nano-size of the crystallites. The mean hardness H and elastic modulus E of the coating were about 1.5 and 70 GPa, respectively. Direct pull-off test recorded a mean coating-substrate bonding strength larger than 17 MPa. Electrochemical impedance spectroscopic (EIS) study and cyclic polarization tests showed that the corrosion resistance of the coated NiTi samples in Hanks’ solution was increased by about two orders of magnitude compared with the substrate. Taken together, the present study showed that steam crystallization is a feasible low-temperature treatment method for sol-gel derived titania coating on NiTi in biomedical applications.     

An in vitro controlled release study of valproic acid encapsulated in a titania ceramic matrix

Despite the therapeutic efficacy of valproic acid towards numerous diseases, its poor bioavailability and systemic side effects pose significant barriers to long term treatment. In order to take advantage of controlled release implants of valproic acid, the drug was encapsulated into titania ceramic matrices via a sol-gel process. The integrity and structure of valproic acid-containing matrices were characterized through the use of FESEM, TEM, and BET analyses. In vitro controlled release studies and kinetic analyses were performed under ambient conditions (25 °C, atmospheric pressure) and controlled release behaviors were studied using a GC-MS method. Results showed first order dependence in the rate of valproic acid release as a function of drug concentrations in the titania ceramic device. A marked dependence on the surface area and pore size distribution with drug loading was also observed. This research opens new possibilities for the design of novel time-delayed controlled release systems for valproic acid encapsulates.     

Synthesis and characterization of hydroxyapatite/titania nanocomposites using in situ precipitation technique

Hydroxyapatite/titania nanocomposites were successfully synthesized by in situ precipitation of precursor matters from hydroxyapatite and titania at 70 °C with different hydroxyapatite/titania ratios. X-ray diffraction, Fourier transform infrared spectroscopy, Brunauer–Emmett–Teller surface, scanning and transmission electron microscopes were employed to characterize the prepared nanocomposite powders. X-ray diffraction results indicated that hydroxyapatite and anatase (TiO₂) were the major crystalline phases. By increasing the amount of titania nano-particles, Fourier transform infrared spectroscopy revealed that (PO₄)³⁻ bands at 567, 1033 cm⁻¹ decreased. Brunauer–Emmett–Teller surface results also showed a reduction in surface areas of nanocomposites. Transmission electron microscope observations revealed that the aspect ratio of hydroxyapatite/TiO₂ nanocrystals increased by increasing TiO₂ proportion in nanocomposites. The observed nanorod crystals tended to thin, elongated and plate-like in shape.     

Boron and nitrogen co-doped titania with enhanced visible-light photocatalytic activity for hydrogen evolution

A visible-light boron and nitrogen co-doped titania (B-N-TiO₂) photocatalyst was prepared by sol-gel method with titanium tetra-n-butyl oxide, urea and boric acid as precursors. The photocatalyst was characterized by Fourier Transform Infrared (FT-IR), UV-vis diffusive reflectance spectroscopy (DRS), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), BET and electrochemistry method. Photocatalytic activity for hydrogen production over platinized B-N-TiO₂ under visible-light (λ ≥ 420 nm) irradiation was investigated. In nitrogen doped titania (N-TiO₂) NTiO bond is formed, which extends the absorption edge to the visible-light region. A part of doping boron enters into titania lattice and most of the boron exists at the surface of the catalyst. The crystallite size of B-N-TiO₂ decreases compared to N-TiO₂, while its photocurrent and the surface hydroxyl group increase. Furthermore, doping boron could act as shallow traps for photoinduced electrons to prolong the life of the electrons and holes. Therefore, the visible-light activity of B-N-iO₂ increases greatly compared with that of N-TiO₂.     

Photopatternable and refractive-index-tunable sol–gel-derived silica–titania nanohybrid materials

Silica–titania nanohybrid materials were synthesized using functionalized organosilanes and organically chelated titanium alkoxide in a simple sol–gel process. The synthesized silica–titania nanohybrid materials exhibited good solution processability and homogeneous dispersion without any phase separation regardless of the ratio of the mixture of the two components. The silica–titania nanohybrid materials exhibited good photoinitiator solubility and effective photocurability with a high degree of degree under ultraviolet (UV) exposure. Because of their high photocurability and solution processability, the silica–titania nanohybrid materials were readily converted into silica–titania nanohybrid films and were used for direct photopatterning without requiring the developing process used in the photomask method. In particular, the refractive indices of the silica–titania nanohybrid materials could be decreased by decreasing the content of chelated titanium alkoxide in the materials. Moreover, the silica–titania nanohybrid films exhibited high transmittance in the visible wavelength range, and their surface roughnesses were very smooth, exhibiting values <1 nm. On the basis of these observations, the fabricated silica–titania nanohybrid materials can be used in solution-processable materials for producing optical and electro-optical elements.     

Continuous one-step synthesis of N-doped titania under supercritical and subcritical water conditions for photocatalytic reaction under visible light

N-doped titania was prepared continuously by one-step synthetic method under supercritical and subcritical water conditions using titanium(IV)tetraisopropoxide (TTIP) and nitric acid as a titania precursor and nitrogen source, respectively. The synthesized N-doped titania particles were characterized by XRD, N₂-adsorption, TEM, XPS, UV-vis diffuse reflectance spectroscopy. N-doped titania was successfully synthesized and its crystalline structure was homogenous anatase phase with high surface area. The absorption edge of synthesized N-doped titania shifted into the visible light region compared with commercial titania P25. All synthesized N-doped titania have higher photocatalytic activity than P25 under visible light irradiation. The photocatalytic activity of N-doped titania synthesized under supercritical water condition was the highest for the degradation of methyl orange under visible light due to the larger crystallite size compared with the N-doped titania synthesized under subcritical water condition.     

The effect of the deposition parameters on size, distribution and antimicrobial properties of photoinduced silver nanoparticles on titania coatings

Controlled photodeposition of silver nanoparticles (AgNP) on titania coatings using two different sources of UV light is described. Titania (anatase) thin films were prepared by the sol-gel dip-coating method on silicon wafers. AgNPs were grown on the titania surface as a result of UV illumination of titania films immersed in aqueous solutions of silver nitrate. UV xenon lamp or excimer laser, both operating at the wavelength 351 ± 5 nm, was used as illumination sources. The AFM topography of AgNP/TiO₂ nanocomposites revealed that silver nanoparticles could be synthesized by both sources of illumination, however the photocatalysis carried out by UV light from xenon lamp illumination leads to larger AgNP than those synthesized using the laser beam. It was found that the increasing concentration of silver ions in the initial solution increases the number of Ag nanoparticles on the titania surface, while longer time of irradiation results the growth of larger size nanoparticles. Antibacterial tests performed on TiO₂ covered by Ag nanoparticles revealed that increasing density of nanoparticles enhances the inhibition of bacterial growth. It was also found that antibacterial activity drops by only 10-15% after 6 cycles compared to the initial use.     

银/二氧化钛核壳纳米颗粒对碲化镉纳米晶的荧光增强研究

利用新合成的复合纳米结构银/二氧化钛核壳纳米颗粒,研究了金属银纳米颗粒对碲化镉纳米晶层荧光的增强情况.结果表明,这种新型复合金属纳米结构能极大地增强发光纳米晶层的荧光强度.银/二氧化钛核壳纳米颗粒是以水合肼、硝酸银和四异丙氧基钛为原材料,利用胶体化学法在水溶液中合成.透射电子显微镜图片表明这种新合成的银/二氧化钛纳米材料基本上呈球形,有较为明显的核壳结构,中间黑色的核是银纳米颗粒,外层颜色较浅部分是二氧化钛壳层.另外,包裹二氧化钛壳层后,银纳米颗粒的表面等离子吸收带从409 nm红移至430 nm,也证实了这种新型核壳纳米材料的形成.将此合成方法得到的银/二氧化钛纳米颗粒和碲化镉纳米晶用旋转涂覆方法进行直接组合后,得到了银纳米颗粒对碲化镉纳米晶荧光的明显增强,并对其增强的物理过程进行了讨论.这种能够增强荧光团发光的新型复合银纳米结构将在发光器件、荧光成像、生物探测等方面具有一定的应用价值.     

Structural study of sol-gel Au/TiO2 films from nanopowders

TiO₂ represents one of the most important sol-gel materials, due to its photocatalytic properties, in the case of both powders and coatings. Nanostructured titania has been reported to be used in many applications in different fields ranging from optics to gas sensor via solar energy. Recent researches point out the existence of new procedures used in order to enhance the efficiency of the photocatalytic process. The metal ion doping is such an example. Two types of 2 wt.% Au containing TiO₂ powders have been embedded in sol-gel vitreous TiO₂ matrices. Au-doped TiO₂ films have been prepared from these sols, by dipping procedure using quartz microscopic slides, as substrates. The relationship between the synthesis conditions and the properties of titania nanosized materials, such as thermal stability, phase composition, crystallinity, and the influence of dopant was investigated. The hydrophilic properties of the films were correlated with their structure, composition and surface morphology.     

Fabrication, characterization and photoelectrochemical properties of Fe2O3 modified TiO2 nanotube arrays

TiO₂ nanotube (NT) arrays modified by Fe₂O₃ with high sensibility in the visible spectrum were first prepared by annealing anodic titania NTs pre-loaded with Fe(OH)₃ which was uniformly clung to the titania NTs using sequential chemical bath deposition (S-CBD). The photoelectrochemical performances of the as-prepared composite nanotubes were determined by measuring the photo-generated currents and voltages under illumination of UV-vis light. The titania NTs modified by Fe₂O₃ showed higher photopotential and photocurrent values than those of unmodified titania NTs. The enhanced photoelectrochemical behaviors can be attributed to the modified Fe₂O₃ which increases the probability of charge-carrier separation and extends the range of the TiO₂ photoresponse from ultraviolet (UV) to visible region due to the low band gap of 2.2 eV of Fe₂O₃.     

Synthesis of Titania-supported Copper Nanoparticles via Refined Alkoxide Sol-gel Process

Nanoparticles of titania and copper-loaded titania were synthesized by a refined sol-gel method using titanium butoxide. Unlike the conventional sol-gel procedure of adding water directly, the esterification of anhydrous butanol and glacial acetic acid provided the hydrolyzing water. In addition, acetic acid also served as a chelating ligand to stabilize the hydrolysis-condensation process and minimize the agglomeration of titania. Following the hydrolysis, Cu/TiO₂ was prepared by adding copper chloride to titania sol. The sol was dried, then calcined at 500^°C to remove organics and transformed to anatase titania which was verified by XRD. Cu/TiO₂ was further hydrogen-reduced at 300^°C. The recovery of Ti was exceeded by an average of 95% from titanium butoxide. TEM micrographs show that the Cu/TiO₂ particles are near uniform. The average crystallite sizes are 17–20 nm estimated from the peak broadening of XRD spectra. The bandgaps of TiO₂ and reduced Cu/TiO₂ range from 2.70 to 3.15 eV estimated from the diffusive reflective UV-Vis spectra. XPS analysis shows that Cu 2p_3/2 is 933.4 eV indicating primary Cu₂O form on the TiO₂ supports. The binding energy of Ti does not exhibit chemical shift suggesting negligible interaction of Cu cluster and TiO₂ support.     

Photocatalytic characterization of silica coated titania nanoparticles with tunable coatings

Photocatalytic experiments were conducted using the silica coated titania nanoparticles with tunable coatings to photocatalytically degrade methyl orange in water solutions. When the silica loading on titania nanoparticles was 4.67 wt%, the silica coating layer was incomplete and the photocatalytic activity of coated nanoparticles was higher than titania nanoparticles. However, when the silica loading on titania nanoparticles increased to 9.33 wt%, the thickness of silica coatings was 1.5 nm and the photocatalytic activity of coated nanoparticles sharply decreased. When the silica loading on titania nanoparticles increased to 25.19 wt%, the coated nanoparticles still exhibited a certain photacatalytic activity due to the porosity of silica coatings. The change of the effective tiania surface area available for methyl orange caused by silica coatings and the dispersion stability were used to explain the difference in photocatalytic activity.     

Photocatalytic characterization of silica coated titania nanoparticles with tunable coatings

Photocatalytic experiments were conducted using the silica coated titania nanoparticles with tunable coatings to photocatalytically degrade methyl orange in water solutions. When the silica loading on titania nanoparticles was 4.67 wt%, the silica coating layer was incomplete and the photocatalytic activity of coated nanoparticles was higher than titania nanoparticles. However, when the silica loading on titania nanoparticles increased to 9.33 wt%, the thickness of silica coatings was 1.5 nm and the photocatalytic activity of coated nanoparticles sharply decreased. When the silica loading on titania nanoparticles increased to 25.19 wt%, the coated nanoparticles still exhibited a certain photacatalytic activity due to the porosity of silica coatings. The change of the effective tiania surface area available for methyl orange caused by silica coatings and the dispersion stability were used to explain the difference in photocatalytic activity.This revised version was published online in August 2005 with a corrected issue number.     

Titanium dioxide nanoparticles prepared by laser pyrolysis: Synthesis and photocatalytic properties

TiO₂ nanoparticles were synthesized via the laser pyrolysis of titanium tetrachloride-based gas-phase mixtures. In the obtained nanopowders, a mixture of anatase and rutile phases with mean particle size of about 14 nm was identified. Using the thermal heated laser nanopowders, mechanically stable films were produced by immobilizing titania nanopowders on glass substrates (the doctor blading method followed by compression). The photocatalytic activity of the prepared films was tested by the degradation of 4-chlorophenol in an aqueous solution under UV-illumination. By referring to known commercial samples (Degussa P25) similarly prepared, higher photocatalytic efficiency was found for the laser-prepared samples.     

Formation and bioactivity of porous titania containing nanostructured Ag

In this work, porous titania were prepared on bulk Ti via chemical oxidation, and then nanostructured Ag was deposited on the surface of titania by ion beam sputtering. After annealing treatment, the nanostructured Ag titania were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), electron probe micro-analyzer (EPMA), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). The influence of nanostructured Ag on the morphology, grain growth, phase transformation, and bioactivity of titania was investigated.     

Effect of cobalt doping and annealing on properties of titania thin films prepared by sol-gel process

Undoped and cobalt doped titania (TiO₂) thin films have been prepared on Si(1 0 0) monocrystal and quartz substrate using the sol-gel deposition method and annealed in air at 450, 550, 650, 750, 850, 950 and 1050 °C. Several experimental techniques (AFM, XRD, Raman spectroscopy, XRR, EDX, XPS, XAS, UV-VIS spectroscopy) have been used to characterize these films. Further more the degree of light induced hydrophilicity was estimated by measuring the contact angle of a water droplet on the film. Increase of the annealing temperature and in smaller degree also cobalt doping predispose titania crystallite growth. The rutile phase was detected at lower temperatures in the cobalt doped films than in the undoped titania films. Cobalt in the cobalt doped TiO₂ was seen to be in Co²⁺ oxidation state, mainly in CoTiO₃ phase when films were annealed at temperatures higher than 650 °C. Cobalt compounds segregated into the sub-surface region and to the surface of the titania, where they formed islands. Cobalt doping red-shifted the fundamental absorption edge further into the visible range, however it did not enhance the light induced hydrophilicity of the thin film surface as compared to the undoped titania thin films.     

Preparation and characterization of titania based nanowires

A new method for preparation of titania nanowires with diameter around 10 nm and length up to 2–3 μm is described. The precursor was prepared from sodium titanate by adding ethylene glycole (EG) and heating at temperature of 198°C for 6 h under reflux. The sodium titanate glycolate formed by this way aggregated into 1D nanostructures and was subsequently transformed into titania glycolate during a chemical treatment with 98% sulfuric acid. Titania nanowires with variable amount of anatase and rutile were prepared by heating to temperatures in the range 350–1000°C. The precursor as well as titania based samples were characterized by X-ray diffraction, Infrared spectroscopy, Scanning electron microscopy, High resolution transmission microscopy, Thermogravimetry, Differential thermal analysis, Evolved gas analysis and Emanation thermal analysis. The nitrogen adsorption/desorption was used for surface area and porosity determination. The photoactivity of the prepared titania samples was assessed by the photocatalytic decomposition of 4-chlorophenol in an aqueous slurry under UV irradiation of 365 nm wavelength.