Morphological and structural characterizations of CrSi2 nanometric films deposited by laser ablation

The structure and morphology of chromium disilicide (CrSi₂) nanometric films grown on 〈1 0 0〉 silicon substrates both at room temperature (RT) and at 740 K by pulsed laser ablation are reported. A pure CrSi₂ crystal target was ablated with a KrF excimer laser in vacuum (∼3 × 10⁻⁵ Pa). Morphological and structural properties of the deposited films were investigated using Rutherford backscattering spectrometry (RBS), grazing incidence X-ray diffraction (GID), X-ray reflectivity (XRR), scanning (SEM) and transmission electron microscopy (TEM). From RBS analysis, the films’ thickness resulted of ∼40 nm. This value is in agreement with the value obtained from XRR and TEM analysis (∼42 and ∼38 nm, respectively). The films’ composition, as inferred from Rutherford Universal Manipulation Program simulation of experimental spectra, is close to stoichiometric CrSi₂. GID analysis showed that the film deposited at 740 K is composed only by the CrSi₂ phase. The RT deposited sample is amorphous, while GID and TEM analyses evidenced that the film deposited at 740 K is poorly crystallised. The RT deposited film exhibited a metallic behaviour, while that one deposited at 740 K showed a semiconductor behaviour down to 227 K.     

Laser synthesis of nanostructures based on transition metal oxides

Nanostructures based on iron oxides in the form of thin films were synthesized while laser chemical vapor deposition (LCVD) of elements from iron carbonyl vapors (Fe(CO)₅) under the action of Ar⁺ laser radiation (λ_L = 488 nm) on the Si substrate surface with power density about 10² W/cm² and vapor pressure 666 Pa. Analysis of surface morphology and relief of the deposited films was carried out with scanning electron microscopy (SEM) and atomic force microscopy (AFM). This analysis demonstrated their cluster structure with average size no more than 100 nm. It was found out that the thicker the deposited film, the larger sizes of clusters with more oxides of higher oxidized phases were formed. The film thickness (d) was 10 and 28 nm. The deposited films exhibited semiconductor properties in the range 170-340 K which were stipulated by oxide content with different oxidized phases. The width of the band gap E_g depends on oxide content in the deposited film and was varied in the range 0.30-0.64 eV at an electrical field of 1.6 × 10³ V/m. The band gap E_g was varied in the range 0.46-0.58 eV at an electrical field of 45 V/m. The band gap which is stipulated by impurities in iron oxides E_i was varied in the range 0.009-0.026 eV at an electrical field of 1.6 × 10³ V/m and was varied in the range 0-0.16 eV at an electrical field 45 V/m. These narrow band gap semiconductor thin films displayed of the quantum dimensional effect.     

Laser synthesis of semiconductor nanostructures with narrow band gap

Semiconductor nanostructures with narrow band gap were synthesized by means of laser chemical vapor deposition (LCVD) of elements from iron carbonyl vapors [Fe(CO)₅] under the action of Ar⁺ laser radiation (λ_L = 488 nm) on the Si substrate surface. The temperature dependence of the specific conductivity of these nanostructures in the form of thin films demonstrated typical semiconductor tendency and gave the possibility to calculate the band gap for intrinsic conductivity (E_g) and the band gap assigned for impurities (E_i), which were depended upon film thickness and applied electrical field. Analysis of deposited films with scanning electron microscopy (SEM) and atomic force microscopy (AFM) demonstrated their cluster structure with average size not more than 100 nm. Semiconductor properties of deposited nanostructures were stipulated with iron oxides in different oxidized phases according to X-ray photoelectron spectroscopy (XPS) analysis.These deposited nanostructures were irradiated with Q-switched YAG laser (λ_L = 1064 nm) at power density about 6 × 10⁷ W/cm². This irradiation resulted in the crystallization process of deposited films on the Si substrate surface. The crystallization process resulted in the synthesis of iron carbide-silicide (FeSi_2−xC_x) layer with semiconductor properties too. The width of the band gap E_g of the synthesized layer of iron carbide-silicide was less than for deposited films based on iron oxides Fe₂O_3−x (0 ≤ x ≤ 1).     

Optical properties of single-phase β-FeSi2 films fabricated by electron beam evaporation

Single-phase semiconducting iron disilicide (β-FeSi₂) films on silicon substrate were fabricated by electron beam evaporation (EBE) technique. For preventing the oxidation of Fe film, silicon/iron/silicon sandwich structure films with different thickness of silicon and iron were deposited and then annealed at different temperatures. X-ray diffraction (XRD), Raman and Fourier transform infrared spectroscopy (FTIR) measurements were carried out to study the phase distribution and crystal quality of the films. Single-phase β-FeSi₂ with high crystal quality was achieved after annealing at 800 °C for 5 h. An apparent direct bandgap E_g of approximately 0.85-0.88 eV was observed in the β-FeSi₂ films. It is considered that the silicon/iron/silicon sandwich structure is suited for formation of single-phase β-FeSi₂ with high crystal quality.     

Physical properties of ZnO thin films deposited by spray pyrolysis technique

Thin films of ZnO have been prepared on glass substrates at different thicknesses by spray pyrolysis technique using 0.2 M aqueous solution of zinc acetate. X-ray diffraction reveals that the films are polycrystalline in nature having hexagonal wurtzite type crystal structure. The resistivity at room temperature is of the order 10⁻² Ω cm and decreased as the temperature increased. Films are highly transparent in the visible region. The dependence of the refractive index, n, and extinction coefficient, k, on the wavelength for a sprayed film is also reported. Optical bandgap, E_g, has been reported for the films. A shift from E_g = 3.21 eV to 3.31 eV has been observed for deposited films.     

Optical properties of ITO/TiO2 single and double layer thin films deposited by RPLAD

Indium tin oxide (ITO) and titanium dioxide (TiO₂) single layer and double layer ITO/TiO₂ films were prepared using reactive pulsed laser ablation deposition (RPLAD) with an ArF excimer laser for applications in dye-sensitized solar cells (DSSCs). The films were deposited on SiO₂ substrates either at room temperatures (RT) or heated to 200-400 °C. Under optimized conditions, transmission of ITO films in the visible (vis) range was above 89% for films produced at RT and 93% for the ones deposited at higher temperatures. Increasing the substrate temperature from RT to 400 °C enhances the transmission of TiO₂ films in the vis-NIR from about 70% to 92%. High transmission (≈90%) was observed for the double layer ITO/TiO₂ with a transmission cut-off above 900 nm. From the transmission data, the energies gaps (E_g), as well as the refractive indexes (n) for the films were estimated. n ≈ 2.03 and 2.04, respectively for ITO films and TiO₂ film deposited at 400 °C in the visible region. Post-annealing of the TiO₂ films for 3 h at 300 and 500 °C was performed to enhance n. The refractive index of the TiO₂ films increases with the post-annealing temperature. The direct band gap is 3.6, 3.74 and 3.82 eV for ITO films deposited at RT, 200, and 400 °C, respectively. The TiO₂ films present a direct band gap of 3.51 and 3.37 eV for as deposited TiO₂ films and when annealed at 400 °C, respectively. There is a shift of about 0.1 eV between ITO and ITO/TiO₂ films deposited at 200 °C. The shift decreases by half when the TiO₂ film was deposited at 400 °C. Post-annealing was also performed on double layer ITO/TiO₂.     

Study of structural and optical properties of ZnO films grown by pulsed laser deposition

Wurtzite zinc oxides films (ZnO) were deposited on silicon (0 0 1) and corning glass substrates using the pulsed laser deposition technique. The laser fluence, target-substrate distance, substrate temperature of 300 °C were fixed while varying oxygen pressures from 2 to 500 Pa were used. It is observed that the structural properties of ZnO films depend strongly on the oxygen pressure and the substrate nature. The film crystallinity improves with decreasing oxygen pressure. At high oxygen pressure, the films are randomly oriented, whereas, at low oxygen pressures they are well oriented along [0 0 1] axis for Si substrates and along [1 0 3] axis for glass substrates. A honeycomb structure is obtained at low oxygen pressures, whereas microcrystalline structures were obtained at high oxygen pressures. The effect of oxygen pressure on film transparency, band gap E_g and Urbach energies was investigated.     

Annealing effect on CdS/SnO2 films grown by chemical bath deposition

The extensive investigation of the annealing effect in nitrogen atmosphere on the structural optical and electrical properties of chemically deposited CdS films on SnO₂ has been performed. The as-deposited film shows 2.45 eV band gap (E_g) and decreases with increasing annealing temperature. The film annealed at 623 K having pure hexagonal phase (a = 4.14 Å, c = 6.71 Å for [1 0 0] plane) and E_g = 2.36 eV shows 10 times higher conductivity for all temperature range, and shows two different activation energies E_a = 0.114 eV and E_a = 0.033 eV for the temperature range 395 K ≤ T ≤ 515 K and 515 K ≤ T ≤ 585 K, respectively. The structural parameters such as dislocation density, strain and optical parameters such as absorption and extinction coefficient are calculated and compared for all the films.     

Fabrication and characterization of La-doped HfO2 gate dielectrics by metal-organic chemical vapor deposition

La-doped HfO₂ gate dielectric thin films have been deposited on Si substrates using La(acac)₃ and Hf(acac)₄ (acac = 2,4-pentanedionate) mixing sources by low-pressure metal-organic chemical vapor deposition (MOCVD). The structure, thermal stability, and electrical properties of La-doped HfO₂ films have been investigated. Inductive coupled plasma analyses confirm that the La content ranging from 1 to 5 mol% is involved in the films. The films show smaller roughness of ∼0.5 nm and improved thermal stability up to 750 °C. The La-doped HfO₂ films on Pt-coated Si and fused quartz substrates have an intrinsic dielectric constant of ∼28 at 1 MHz and a band gap of 5.6 eV, respectively. X-ray photoelectron spectroscopy analyses reveal that the interfacial layer is Hf-based silicate. The reliable value of equivalent oxide thickness (EOT) around 1.2 nm has been obtained, but with a large leakage current density of 3 A/cm² at V_g = 1V + V_fb. MOCVD-derived La-doped HfO₂ is demonstrated to be a potential high-k gate dielectric film for next generation metal oxide semiconductor field effect transistor applications.     

Characterization of ZnO-SnO2 thin film composites prepared by pulsed laser deposition

Thin films of ZnO-SnO₂ composites have been deposited on Si(1 0 0) and glass substrates at 500 °C by pulsed laser ablation using different composite targets with ZnO amount varying between 1 and 50 wt%. The effect of increasing ZnO-content on electrical, optical and structural properties of the ZnO-SnO₂ films has been investigated. X-ray diffraction analysis indicates that the as-deposited ZnO-SnO₂ films can be both crystalline (for ZnO <1 wt%) and amorphous (for ZnO ≥ 10 wt%) in nature. Atomic force microscopy studies of the as-prepared composite films indicate that the surfaces are fairly smooth with rms roughness varying between 3.07 and 2.04 nm. The average optical transmittance of the as-deposited films in the visible range (400-800 nm), decreases from 90% to 72% for increasing ZnO concentration in the film. The band gap energy (E_g) seems to depend on the amount of ZnO addition, with the maximum obtained at 1 wt% ZnO. Assuming that the interband electron transition is direct, the optical band gap has been found to be in the range 3.24-3.69 eV for as-deposited composite films. The lowest electrical resistivity of 7.6 × 10⁻³ Ω cm has been achieved with the 25 wt% ZnO composite film deposited at 500 °C. The photoluminescence spectrum of the composite films shows a decrease in PL intensity with increasing ZnO concentration.     

Structural-optical study of high-dielectric-constant oxide films

High-k polycrystalline Pr₂O₃ and amorphous LaAlO₃ oxide thin films deposited on Si(0 0 1) are studied. The microstructure is investigated using X-ray diffraction and scanning electron microscopy. Optical properties are determined in the 0.75-6.5 eV photon energy range using spectroscopic ellipsometry. The polycrystalline Pr₂O₃ films have an optical gap of 3.86 eV and a dielectric constant of 16-26, which increases with film thickness. Similarly, very thin amorphous LaAlO₃ films have the optical gap of 5.8 eV, and a dielectric constant below 14 which also increases with film thickness. The lower dielectric constant compared to crystalline material is an intrinsic characteristic of amorphous films.     

Influence of air annealing on the structural, morphological, optical and electrical properties of chemically deposited ZnSe thin films

Zinc selenide nanocrystalline thin films are grown onto amorphous glass substrate from an aqueous alkaline medium, using chemical bath deposition (CBD) method. The ZnSe thin films are annealed in air for 4 h at various temperatures and characterized by structural, morphological, optical and electrical properties. The as-deposited ZnSe film grew with nanocrystalline cubic phase alongwith some amorphous phase present in it. After annealing metastable nanocrystalline cubic phase was transformed into stable polycrystalline hexagonal phase with partial conversion of ZnSe into ZnO. The optical band gap, E_g, of as-deposited film is 2.85 eV and electrical resistivity of the order of 10⁶-10⁷ Ω cm. Depending upon annealing temperature, decrease up to 0.15 eV and 10² Ω cm were observed in the optical band gap, E_g, and electrical resistivity, respectively.     

Chemical bath-deposited ZnS thin films: Preparation and characterization

Chemical bath deposition of ZnS thin films from NH₃/SC(NH₂)₂/ZnSO₄ solutions has been studied. The effect of various process parameters on the growth and the film quality are presented. The influence on the growth rate of solution composition and the structural, optical properties of the ZnS thin films deposited by this method have been studied. The XRF analysis confirmed that volume of oxygen of the as-deposited film is very high. The XRD analysis of as-deposited films shows that the films are cubic ZnS structure. The XRD analysis of annealed films shows the annealed films are cubic ZnS and ZnO mixture structure. Those results confirmed that the as-deposited films have amorphous Zn(OH)₂. SEM studies of the ZnS thin films grown on various growth phases show that ZnS film formed in the none-film phase is discontinuous. ZnS film formed in quasi-linear phase shows a compact and a granular structure with the grain size about 100 nm. There are adsorbed particles on films formed in the saturation phase. Transmission measurement shows that an optical transmittance is about 90% when the wavelength over 500 nm. The band gap (E_g) value of the deposited film is about 3.51 eV.     

Structural, morphological and optical properties of CuAlS2 films deposited by spray pyrolysis method

The structural, morphological and optical properties of CuAlS₂ films deposited by spray pyrolysis method have been investigated. CuAlS₂ in the form of films is prepared at different deposition conditions by a simple and economical spray pyrolysis method. The structural, surface morphology and optical properties of the films were analyzed by X-ray diffraction (XRD), scanning electron microscope (SEM), atomic force microscope (AFM) and absorbance spectra, respectively. The films were polycrystalline, crystallized in a tetragonal structure, and are preferentially orientated along the (1 1 2) direction. Grain size values, dislocation density, and d% error of CuAlS₂ films were calculated. The optical band gap of the CuAlS₂ film was found to be 3.45 eV. The optical constants such as refractive index, extinction coefficient and dielectric constants of the CuAlS₂ film were determined. The refractive index dispersion curve of the film obeys the single oscillator model. Optical dispersion parameters E_o and E_d developed by Wemple-DiDomenico were calculated and found to be 3.562 and 12.590 eV.     

Characteristics of filtered vacuum arc deposited ZnO-SnO2 thin films on room temperature substrates

ZnO, SnO₂ and zinc stannate thin films were deposited using filtered vacuum arc deposition (FVAD) system on commercial microscope glass and UV fused silica substrates (UVFS) at room temperature (RT). The structural and morphological analyses were performed using X-ray diffraction (XRD) and Atomic Force Microscopy (AFM), respectively. XRD patterns of ZnO films deposited at RT had strongly c-axis orientation, whereas SnO₂ and zinc stannate films had amorphous structure as they did not have any defined patterns. Average crystalline size and surface grain size of ZnO films were ∼16 nm, as determined from diffraction line broadening and AFM images, respectively. Optical constants in the 250-1100 nm wavelength range were determined by variable angle spectroscopic ellipsometry and transmission measurements. The transmission of the deposited films in the VIS was 80-90%, affected by interference. The refractive indices and the extinction coefficients of deposited ZnO, SnO₂ and zinc stannate films were in the range 1.87-2.15 and 0.02-0.04, depending on wavelengths and deposition parameters. The optical band gap (E_g) was determined by the dependence of the absorption coefficient on the photon energy at short wavelengths. Its values for ZnO, SnO₂ and zinc stannate were in the range 3.25-3.30 eV, 3.60-3.98 eV and 3.43-3.52 eV, respectively, depending on the deposition pressure.     

Characterization of chemically deposited ZnSe/SnO2/glass films: Influence of annealing in Ar atmosphere on physical properties

The Zinc Selenide (ZnSe) thin films have been deposited on SnO₂/glass substrates by a simple and inexpensive chemical bath deposition (CBD). The structural, optical and electrical properties of ZnSe films have been characterized by X-ray diffraction (XRD), Energy Dispersive X-ray Analysis (EDAX), optical absorption spectroscopy, and four point probe techniques, respectively. The films have been subjected to different annealing temperature in Argon (Ar) atmosphere. An increase in annealing temperature does not cause a complete phase transformation whereas it affects the crystallite size, dislocation density and strain. The optical band gap (E_g) of the as-deposited film is estimated to be 3.08 eV and decreases with increasing annealing temperature down to 2.43 eV at 773 K. The as-deposited and annealed films show typical semiconducting behaviour, dρ/dT > 0. Interestingly, the films annealed at 373 K, 473 K, and 573 K show two distinct temperature dependent regions of electrical resistivity; exponential region at high temperature, linear region at low temperature. The temperature at which the transition takes place from exponential to linear region strongly depends on the annealing temperature.     

Synthesis and characterization of Zn(O,OH)S and AgInS2 layers to be used in thin film solar cells

In this paper AgInS₂ and Zn(O,OH)S thin films were synthesized and characterized. AgInS₂ layers were grown by co-evaporation from metal precursors in a two-step process, and, Zn(O,OH)S thin films were deposited from chemical bath containing thiourea, zinc acetate, sodium citrate and ammonia. X-ray diffraction measurements indicated that AgInS₂ thin films grown with chalcopyrite structure, and the as-grown Zn(O,OH)S thin films were polycrystalline. It was also found that the AgInS₂ films presented p-type conductivity, a high absorption coefficient (greater than 10⁴ cm⁻¹) and energy band-gap E_g of about 1.95 eV, Zn(O,OH),S thin films presented E_g of about 3.89 eV. Morphological analysis showed that under this synthesis conditions Zn(O,OH),S thin films coated uniformly the absorber layer. Additionally, the Zn(O,OH)S kinetic growth on AgInS₂ layer was studied also. Finally, the results suggest that these layers possibly could be used in one-junction solar cells and/or as top cell in a tandem solar cell.     

Growth dynamics of pulsed laser deposited indium oxide thin films: a substrate dependent study

Indium oxide films are deposited by pulsed laser deposition in the presence of oxygen atmosphere, on different substrates, namely GaAs, Si, quartz, and glass. The structural, morphological, and interface characteristics are studied. Cubic In₂O₃ phase is confirmed by high resolution X-ray diffraction measurements. While the films on Si, glass, and quartz substrates are polycrystalline, the films on GaAs exhibit a preferred orientation along (2 2 2) plane. The structure and crystalline nature of the films are also confirmed by Raman spectroscopy. Furthermore, Raman spectra show the appearance of gallium oxide modes arising due to Ga diffusion from the substrate. The morphology of the films deposited on different substrates is studied by atomic force microscopy and rms roughness values are obtained. A two-dimensional power spectral density analysis has been used to calculate the growth exponent (α). A value of α > 1 (α < 1) for films grown on GaAs/Si (quartz/glass) substrates suggests that the growth on crystalline substrates is governed by the linear diffusion model, whereas the growth on amorphous substrates follows the dynamic scaling behaviour. UV-visible study shows a high optical transmittance of >90% and a band gap value of 3.64 and 3.79 eV for the films deposited on quartz and glass substrates, respectively.     

Deposition of potassium-oxygen on silicon surfaces by pulsed laser ablation of potassium superoxide: Study of work function changes

Potassium-oxygen species were deposited on pure, Si nanoparticles coated and H-terminated Si nanoparticles coated p-Si(1 0 0) surfaces by pulsed laser ablation of potassium superoxide (KO₂) target. The deposition properties, composition and the work function changes of the deposited species were investigated in situ using an X-ray photoelectron spectroscopy (XPS) and a Kelvin probe measurement. The deposited species were assigned to K₂O₂ and KO₂, and they can be selectively deposited by controlling the laser fluence: i.e., at 200 mJ/cm² and at those more than 300 mJ/cm², respectively. Experimental results showed that the work function decreased drastically with depositing of KO_x (x = 1 or 2), and the minimum work function values observed were 1.0 eV and 0.7 eV for pure p-Si(1 0 0) and Si nanoparticles coated substrates, respectively. The study demonstrates the formation of the surface species with minimum work function can be identified by XPS.     

Iron disilicide formation by Au-Si eutectic reaction on Si substrate

We have investigated the growth of iron disilicide on Au-coated Si(0 0 1) substrates and its photoluminescence behaviour. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy observations revealed that the Si surface above 380 °C was melted as a result of the Au-Si eutectic reaction and that coarse island disilicide grains with sizes of several micrometres were formed on the Si surface. The full width at half maximum of 0.056° on the rocking curve of α-FeSi₂004 was observed on the sample deposited at 800 °C, and indicated the high crystal quality in perfection of orientation. The photoluminescence spectrum of β-FeSi₂ grains, which were deposited at 750 °C, was observed. The melted Si surface contributed to the improved crystallinity of α-FeSi₂ and β-FeSi₂.