Thermodynamic and quantum chemistry characterization of the adsorption of triazole derivatives during Muntz corrosion in acidic and neutral solutions

Some triazole derivatives (4-amino-5-mercapto-3-methyl 1,2,4-triazole (AMMT), 4-amino-5-mercapto-3-ethyl 1,2,4-triazole (AMET) and 4-amino-5-mercapto-3-propyl 1,2,4-triazole (AMPT)) have been evaluated as new corrosion inhibitors for the corrosion of muntz alloy (60Cu-40Zn) in acidic and neutral solutions. The adsorption of these compounds has been tested thermodynamically which was found to be of a physisorption mode. Furthermore, some activation thermodynamic parameters such as ΔH^*, ΔS^* and ΔG^* of activation have been estimated. In addition, a trial to find a quantitative relationship between the inhibition efficiency and the electronic properties of the inhibitor molecules was carried out.     

Parallel synthesis of 1,2,4-triazole derivatives using microwave and continuous-flow techniques

Abstract  

An efficient and convenient solution-phase synthesis of a 1H-1,2,4-triazole library with potential agrochemical activity is reported employing microwave-assisted organic synthesis (MAOS) and continuous-flow microfluidic synthetic methods starting from commercially available 3,5-dibromo-1H-1,2,4-triazole (1). MAOS was used for the synthesis of 5-amino-3-bromo-1,2,4-triazole analogs 3 and for their 3-aryl derivatives 4 via Suzuki–Miyaura coupling with polymer-supported catalyst. A microfluidic hydrogenation reactor integrated into an automated parallel synthesis platform was built and utilized for the reductive dehalogenation reactions providing 5-aminotriazoles (5).     

Inhibiting effects of some oxadiazole derivatives on the corrosion of mild steel in perchloric acid solution

The efficiency of 3,5-bis(n-pyridyl)-1,3,4-oxadiazole (n-POX, n = 1, 2, 3), as corrosion inhibitors for mild steel in 1 M perchloric acid (HClO₄) have been determined by weight loss measurements and electrochemical studies. The results show that these inhibitors revealed a good corrosion inhibition even at very low concentrations. Comparison of results among those obtained by the studied oxadiazoles shows that 3-POX was the best inhibitor. Polarisation curves indicate that n-pyridyl substituted-1,3,4-oxadiazoles are mixed type inhibitors in 1 M HClO₄. The adsorption of these inhibitors follows a Langmuir isotherm model. The electronic properties of n-POX, obtained using the AM1 semi-empirical quantum chemical approach, were correlated with their experimental efficiencies using the linear resistance model (LR).     

Enhanced corrosion resistance of mild steel in normal sulfuric acid medium by 2,5-bis(n-thienyl)-1,3,4-thiadiazoles: Electrochemical, X-ray photoelectron spectroscopy and theoretical studies

The inhibitive action of some thiadiazole derivatives, namely 2,5-bis(2-thienyl)-1,3,4-thiadiazole (2-TTH) and 2,5-bis(3-thienyl)-1,3,4-thiadiazole (3-TTH) against the corrosion of mild steel in 0.5 M H₂SO₄ solution has been investigated using weight loss measurements, Tafel polarisation and electrochemical impedance spectroscopy (EIS) techniques. The experimental results obtained revealed that these compounds inhibited the steel corrosion in acid solution. The protection efficiency increased with increasing inhibitors concentration and the ability of the molecule to adsorb on the steel surface was dependent on the position of the sulphur atom on the thienyl substituent. Inhibition efficiency values obtained from various methods employed were in reasonable agreement. Potentiodynamic polarisation studies clearly showed that 2-TTH and 3-TTH acted as mixed inhibitors. Adsorption of these inhibitors on steel surface obeyed to Langmuir adsorption isotherm. X-ray photoelectron spectroscopy and the thermodynamic data of adsorption showed that inhibition of steel corrosion in normal sulphuric solution by n-TTH is due to the formation of a chemisorbed film on the steel surface. Molecular modelling was used to gain some insight, about structural and electronic effects in relation to the inhibiting efficiencies.     

Thermodynamic investigations of ternary o-toluidine + tetrahydropyran + N,N-dimethylformamide mixture and its binaries at 298.15, 303.15 and 308.15 K

The densities ρ, speed of sound u, data of o-toluidine (i) + tetrahydropyran (j) + N,N-dimethylformamide (k) and its {tetrahydropyran (j) + N,N-dimethylformamide (k); o-toluidine (i) + N,N-dimethylformamide (k)} binaries have been measured as a function of composition at 298.15, 303.15 and 308.15 K. The excess molar enthalpies, H^E data of same set of binary mixtures have also been measured over entire composition at 308.15 K. The densities and speeds of sound data of binary and ternary mixtures have been utilized to determine their excess molar volumes, V^E and excess isentropic compressibilities, κ_S^E. The observed thermodynamic properties of binary and ternary mixtures have been analyzed in terms of Graph theory. It has been observed that Graph theory correctly predicts the sign as well as magnitude of thermodynamic properties.     

A luminescent dinuclear Eu(III) complex based on 2,8-bis(4′,4′,4′,-trifluoro-1′,3′-dioxobutyl)-dibenzothiophene for light-emitting diodes

A dinuclear Eu (III) complex Eu₂(dbt)₃·4H₂O was synthesized, where H₂dbt was 2,8-bis(4′,4′,4′,-trifluoro-1′,3′-dioxobutyl)-dibenzothiophene. The complex emits the characteristic red luminescence of Eu³⁺ ion due to the ⁵D₀→⁷F_J(J=0-4) transitions under 395 nm-light excitation with a luminescent quantum efficiency of 17%. The complex is thermally stable up to 280 °C. It was found that the complex can be effectively excited by a 395 nm-emitting InGaN chip. Bright red light was obtained using the complex as light color-conversion material.     

Experimental and theoretical study for corrosion inhibition of mild steel in hydrochloric acid solution by some new hydrazine carbodithioic acid derivatives

The corrosion inhibition of mild steel in 0.5 M hydrochloric acid solutions by some new hydrazine carbodithioic acid derivatives namely N′-furan-2-yl-methylene-hydrazine carbodithioic acid (A), N′-(4-dimethylamino-benzylidene)-hydrazine carbodithioic acid (B) and N′-(3-nitro-benzylidene)-hydrazine carbodithioic (C) was studied using chemical (weight loss) and electrochemical (potentiodynamic and electrochemical impedance spectroscopy, EIS) measurements. These measurements show that the inhibition efficiency obtained by these compounds increased by increasing their concentration. The inhibition efficiency follow the order C > B > A. Polarization studies show that these compounds act as mixed type inhibitors in 0.5 M HCl solutions. These inhibitors function through adsorption following Langmuir isotherm. The electronic properties of these inhibitors, obtained using PM3 semi-empirical self-consistence field method, have been correlated with their experimental efficiencies using non-linear regression method.     

Non-doped-type white organic light-emitting diodes for lighting purpose

We demonstrate a non-doped white organic light-emitting diode (WOLED) in which the blue-, green- and red-emissions are generated from 4,4′-bis(2,2′-diphenylvinyl)-1,1′-biphenyl, tris(8-hydroxyquinoline)aluminum (Alq) and 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethyl-julolidyl 9-enyl)-4H-pyran (DCJTB), which is used as an ultrathin layer. The DCJTB ultrathin layer plays the chromaticity tuning role in optimizing the white spectral band by modulating the location of the DCJTB ultrathin layer in the green emissive Alq layer. The optimized WOLED gives the Commission Internationale de l’Eclairage-1931 xy coordinates of (0.319, 0.335), a color rendering index of 91.2 at 10 V, a maximum brightness of 21010 cd/m² at 12 V and a maximum current efficiency of 5.17 cd/A at 6.6 V. The electroluminescence mechanism of the white device is also discussed.     

Synthesis,measurements, and theoretical analysis of carbazole derivatives with high-triplet-energy

In order to obtain the blue light-emitting organic materials with high triplet state energy, two 3,5-diphenyl-4H-1,2,4-triazole (Tz) containing carbazole (Cz) derivatives of 9-(4-(3,5-diphenyl-4H-1,2,4-triazol-4-yl)phenyl)-9H-carbazole (TzCz1) and 3,6-di-tert-butyl-9-(4-(3,5-diphenyl-4H-1,2,4-triazol-4-yl)phenyl)-9H-carbazole (TzCz2) are synthesized using Cz acting as the starting material, as well as characterized by the ¹H NMR spectra, ultraviolet–visible (UV–vis) absorption spectra, and the IR absorption spectra. The luminescence quantum yields (LQYs) of TzCz1 and TzCz2 are measured in CH₂Cl₂ solution to be 32.1% and 47.5%, respectively. The electrochemical analysis and the photophysical measurements suggest that the triplet energy levels and the energy gaps of the highest-occupied orbital and the lowest-unoccupied orbital are 2.83 eV and 3.59 eV for TzCz1, and 2.80 eV and 3.43 eV for TzCz2. At last, the theoretical analyses of their ground state geometries and the simulated UV–vis absorption spectra are carried out at B3LYP1/6-31G? level. The studies mentioned above indicate that both TzCz1 and TzCz2 are suitable for the host materials of blue light-emitting diodes.     

The corrosion inhibition and gas evolution studies of some surfactants and citric acid on lead alloy in 12.5 M H2SO4 solution

The inhibition action of the citric acid and three surfactants: sodium dodecyl sulfate (SDS), t-octyl phenoxy polyethoxyethanol (Triton X-100), sodium dodecyl benzene sulphonate (SDBS) on the corrosion behavior and gas evolution of Pb-Sb-As-Se was investigated in 12.5 M H₂SO₄ solution with linear sweep polarization, cyclic voltammetry and weight loss measurements methods. The results drawn from different techniques are comparable. It was found that these surfactants and citric acid act as good inhibitors for the corrosion of lead alloy in H₂SO₄ solution. SDS inhibited most effectively the lead alloy corrosion among the three surfactants and citric acid. The inhibition efficiency for the inhibitors decreases in the order: SDS > SDBS > Triton X-100 > citric acid > blank. The inhibition efficiency increases with rising of the inhibitor concentration. In this work, the effect of the inhibitors on hydrogen and oxygen evolution was studied. In addition, it was found that the adsorption of used inhibitors on lead alloy surface follows Langmuir isotherm.     

Methyl concentration time-histories during iso-octane and n-heptane oxidation and pyrolysis

Methyl radical concentration time-histories were measured during the oxidation and pyrolysis of iso-octane and n-heptane behind reflected shock waves. Initial reflected shock conditions covered temperatures of 1100-1560 K, pressures of 1.6-2.0 atm and initial fuel concentrations of 100-500 ppm. Methyl radicals were detected using cw UV laser absorption near 216 nm; three wavelengths were used to compensate for time- and wavelength-dependent interference absorption. Methyl time-histories were compared to the predictions of several current oxidation models. While some agreement was found between modeling and measurement in the early rise, peak and plateau values of methyl, and in the ignition time, none of the current mechanisms accurately recover all of these features. Sensitivity analysis of the ignition times for both iso-octane and n-heptane showed a strong dependence on the reaction C₃H₅ + H = C₃H₄ + H₂, and a recommended rate was found for this reaction. Sensitivity analysis of the initial rate of CH₃ production during pyrolysis indicated that for both iso-octane and n-heptane, reaction rates for the initial decomposition channels are well isolated, and overall values for these rates were obtained. The present concentration time-history data provide strong constraints on the reaction mechanisms of both iso-octane and n-heptane oxidation, and in conjunction with OH concentration time-histories and ignition delay times, recently measured in our laboratory, should provide a self-consistent set of kinetic targets for the validation and refinement of iso-octane and n-heptane reaction mechanisms.     

A perturbation theory study of H2 on LiF(0 0 1)

In response to recent helium atom scattering (HAS) results, Monte Carlo (MC) simulations and perturbation theory have been performed for H₂ on LiF(0 0 1). MC simulations predict that H₂ molecules form a series of structures, p(2 × 2), p(8 × 2), p(4 × 2) with coverages Θ = 0.5, 0.625 and 0.75, respectively, that are stable up to 8 K. This is in partial agreement with the HAS results that report c(2 × 2) and c(8 × 2) structures; they agree in terms of coverage and stability, but disagree in terms of symmetry. To reconcile the results of the simulations and experiments, the orientation of the adsorbed H₂ molecules was studied using perturbation theory. These calculations show that the adsorbed H₂ molecules are azimuthally delocalized and that the structures are c-type rather then p-type. The calculations also indicate that p-H₂ and helicoptering o-H₂ prefer cationic sites, while cartwheeling o-H₂ prefers anionic sites.     

The n-butyl amine TPD measurement of Brönsted acidity for solid catalysts by simultaneous TG/DTG-DTA

The method for Brönsted acidity measurement based on TPD of alkyl amines desorption by gas-chromatography or thermogravimetry was adapted for simultaneous TG/DTG-DTA analysis. The acidity measurements were focused on the 12-tungstophosphoric acid (H₃PW₁₂O₄₀) and its salts, especially with Cesium since these posses the highest Brönsted acidity and they are among the most interesting catalysts. The n-butyl amine (NBA) desorption takes place in three steps for Cs_xH_3−xPW₁₂O₄₀, x = 0-2, and four steps for the Cs_2.5H_0.5PW₁₂O₄₀. The steps of desorption correspond to the release of NBA molecules in stages, as NBA or butene molecules resulted from the Hofmann elimination reaction and NH₃ + H₂O formed by decomposition of ammonium salt. The quantities of desorption products, C₄H₈ and NH₃ + H₂O, corresponding to the stages with the maximum desorption rates at 400-420 °C, respectively 560-600 °C, are in the stoichiometric ratio with the Brönsted acidity.     

Electrochemical and quantum chemical studies of some Schiff bases on the corrosion of steel in H2SO4 solution

The efficiency, as steel-corrosion inhibitors in 0.1 M and 1 M H₂SO₄, of two Schiff bases, 2-{[(4-methoxyphenyl)imino]methyl}phenol and 1-{[(4-methoxyphenyl)imino]methyl}-2-naphthol, (abbreviated SB-1 and SB-2, respectively) was investigated by Tafel extrapolation and linear polarization methods. Corrosion parameters and adsorption isotherms were determined from current-potential curves. It was found that the percent inhibition efficiencies (η%) and surface coverage (θ) increase with an increases in the concentrations of inhibitors. The results showed that these compounds act as good corrosion inhibitors especially at high concentrations. The adsorption of used compounds on the steel surface obeys Langmuir's isotherm. Obvious correlation was found between corrosion inhibition efficiency and quantum chemical parameters obtained by B3LYP/6-31g(d) method. The obtained theoretical results have been compared with the experimental findings.     

Efficient red organic light-emitting diode sensitized by a phosphorescent Ir compound

The efficiencies of red organic light-emitting diode (OLED) using tris-(8-hydroxy-quinoline)aluminum (Alq₃) as host and 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB) as dopant were greatly increased by adding a small amount (0.3 wt%) of Ir compound, iridium(III) bis(3-(2-benzothiazolyl)-7-(diethylamino)-2H-1-benzopyran-2-onato-N′,C⁴) (acetyl acetonate) (Ir(C6)₂(acac)), as a sensitizer. The device has a sandwiched structure of indium tin oxide (ITO)/4,4′,4″-tris(N-(2-naphthyl)-N-phenyl-amino)triphenylamine (T-NATA) (40 nm)/N,N′-bis(1-naphthyl)-N,N′-diphenyl-1,1′-biphenyl-4,4′ diamine (NPB) (40 nm)/Alq₃:DCJTB (0.7 wt%):Ir(C6)₂(acac) (0.3 wt%) (40 nm)/Alq₃ (40 nm)/LiF (1 nm)/Al (120 nm). It can be seen that the current efficiencies of this device remained almost (13.8±1) cd/A from 0.1 to 20,000 cd/m² and the Commission International d’Eclairage (CIE) coordinates at (0.60, 0.37) in the range of wide brightness. The significant improvement was attributed to the sensitization effect of the doped Ir(C6)₂(acac), thus the energy of singlet and triplet excitons is simultaneously transferred to the DCJTB.     

1,3-Bis(3-hyroxymethyl-5-methyl-1-pyrazole) propane as corrosion inhibitor for steel in 0.5 M H2SO4 solution

The effect of addition of 1,3-bis(3-hyroxymethyl-5-methyl-1-pyrazole) propane (M = 264 g). HMPP on steel corrosion in 0.5 M sulphuric acid is studied by weight-loss, electrochemical polarisation and electrochemical impedance spectroscopy (EIS) measurements at various temperatures. The results obtained showed that HMPP acts as a good corrosion inhibitor. The inhibition efficiency increases with the bipyrazole compound to attain 88%. It acts as a mixed-type inhibitor. Trends in the increase of charge-transfer resistance and decrease of capacitance values also show the adsorption of the molecule on the metal surface. The bipyrazole adsorbs on the steel surface according to the Langmuir isotherm adsorption model. Effect of temperature indicates that inhibition efficiency decreases with temperature between 25 and 85 °C.     

Berberine as a natural source inhibitor for mild steel in 1 M H2SO4

Berberine was abstracted from coptis chinensis and its inhibition efficiency on corrosion of mild steel in 1 M H₂SO₄ was investigated through weight loss experiment, electrochemical techniques and scanning electronic microscope (SEM) with energy disperse spectrometer (EDS). The weight loss results showed that berberine is an excellent corrosion inhibitor for mild steel immersed in 1 M H₂SO₄. Potentiodynamic curves suggested that berberine suppressed both cathodic and anodic processes for its concentrations higher than 1.0 × 10⁻⁴ M and mainly cathodic reaction was suppressed for lower concentrations. The Nyquist diagrams of impedance for mild steel in 1 M H₂SO₄ containing berberine with different concentrations showed one capacitive loop, and the polarization resistance increased with the inhibitor concentration rising. A good fit to Flory-Huggins isotherm was obtained between surface coverage degree and inhibitor concentration. The surface morphology and EDS analysis for mild steel specimens in sulfuric acid in the absence and presence of the inhibitor also proved the results obtained by the weight loss and electrochemical experiments. The correlation of inhibition effect and molecular structure of berberine was then discussed by quantum chemistry study.     

Study of interaction of butyl p-hydroxybenzoate with human serum albumin by molecular modeling and multi-spectroscopic method

Study of the interaction between butyl p-hydroxybenzoate (butoben) and human serum albumin (HSA) has been performed by molecular modeling and multi-spectroscopic method. The interaction mechanism was predicted through molecular modeling first, then the binding parameters were confirmed using a series of spectroscopic methods, including fluorescence spectroscopy, UV-visible absorbance spectroscopy, circular dichroism (CD) spectroscopy and Fourier transform infrared (FT-IR) spectroscopy. The thermodynamic parameters of the reaction, standard enthalpy ΔH⁰ and entropy ΔS⁰, have been calculated to be −29.52 kJ mol⁻¹ and −24.23 J mol⁻¹ K⁻¹, respectively, according to the Van’t Hoff equation, which suggests the van der Waals force and hydrogen bonds are the predominant intermolecular forces in stabilizing the butoben-HSA complex. Results obtained by spectroscopic methods are consistent with that of the molecular modeling study. In addition, alteration of secondary structure of HSA in the presence of butoben was evaluated using the data obtained from UV-visible absorbance, CD and FT-IR spectroscopies.     

A Monte Carlo simulation study of H2 layers on NaCl(0 0 1)

Monte Carlo simulations show that, at one monolayer coverage, H₂ molecules adsorbed on a NaCl(0 0 1) surface occupy all Na⁺ sites and form a commensurate c(2 × 2) structure. If the Cl⁻ sites are occupied as well, a bi-layer p(2 × 1) structure forms. An examination of the H₂ molecules’ rotational motion shows the molecular axes are azimuthally delocalized and so both of the structures acquire (1 × 1) symmetry in accord with experimental observations. These calculations also show that helicoptering o-H₂ (J = 1, m = ±1) prefer to sit on top of Na⁺ sites, while cartwheeling o-H₂ (J = 1, m = 0) prefers to locate over Cl⁻ sites, in agreement with other work.