Surfactants treatment of crude oil contaminated soils

This study reports experimental measurements investigating the ability of a biological (rhamnolipid) and a synthetic (sodium dodecyl sulfate, SDS) surfactant to remove the North Sea Ekofisk crude oil from various soils with different particle size fractions under varying washing conditions. The washing parameters and ranges tested were as follows: temperature (5 to 50 degrees C), time (5 to 20 min), shaking speed (80 to 200 strokes/min), volume (5 to 20 cm3), and surfactant concentration (0.004 to 5 mass%). The contaminated soils were prepared in the laboratory by mixing crude oil and soils using a rotating cylindrical mixer. Two contamination cases were considered: (1) weathered contamination was simulated by keeping freshly contaminated soils in a fan assisted oven at 50 degrees C for 14 days, mimicking the weathering effect in a natural hot environment, and (2) nonweathered contamination which was not subjected to the oven treatment. The surfactants were found to have considerable potential in removing crude oil from different contaminated soils and the results were comparable with those reported in literature for petroleum hydrocarbons. The removal of crude oil with either rhamnolipid or SDS was within the repeatability range of +/-6%. The most influential parameters on oil removal were surfactant concentration and washing temperature. The soil cation exchange capacity and pH also influenced the removal of crude oil from the individual soils. However, due to the binding of crude oil to soil during weathering, low crude oil removal was achieved with the weathered contaminated soil samples.     

Formation and properties of reverse micellar cubic liquid crystals and derived emulsions

The structure of the reverse micellar cubic (I2) liquid crystal and the adjacent micellar phase in amphiphilic block copolymer/water/oil systems has been studied by small-angle X-ray scattering (SAXS), rheometry, and differential scanning calorimetry (DSC). Upon addition of water to the copolymer/oil mixture, spherical micelles are formed and grow in size until a disorder-order transition takes place, which is related to a sudden increase in the viscosity and shear modulus. The transition is driven by the packing of the spherical micelles into a Fd3m cubic lattice. The single-phase I2 liquid crystals show gel-like behavior and elastic moduli higher than 104 Pa, as determined by oscillatory measurements. Further addition of water induces phase separation, and it is found that reverse water-in-oil emulsions with high internal phase ratio and stabilized by I2 liquid crystals can be prepared in the two-phase region. Contrary to liquid-liquid emulsions, both the elastic modulus and the viscosity decrease with the fraction of dispersed water, due to a decrease in the crystalline fraction in the sample, although the reverse emulsions remain gel-like even at high volume fractions of the dispersed phase. A temperature induced order-disorder transition can be detected by calorimetry and rheometry. Upon heating the I2 liquid crystals, two thermal events associated with small enthalpy values were detected: one endothermic, related to the "melting" of the liquid crystal, and the other exothermic, attributed to phase separation. The melting of the liquid crystal is associated with a sudden drop in viscosity and shear moduli. Results are relevant for understanding the formation of cubic-phase-based reverse emulsions and for their application as templates for the synthesis of structured materials.     

Determination of aromatic amines in environmental water samples using solid-phase extraction modified with sodium dodecyl sulphate and micellar liquid chromatography

Extraction and determination of seven aromatic amines in environmental water samples were performed with solid-phase extraction (SPE) and micellar liquid chromatography (MLC) using experimental design. Extraction of aromatic amines was carried out with a C₁₈ cartridge modified with sodium dodecyl sulphate (SDS). The washing solution and elution solvent for extraction of aromatic amines were aqueous solution containing 5% (v/v) acetonitrile and 5% (v/v) acetone and 3 mL methanol, respectively. The chemometrics approach was applied for the separation optimisation of these compounds using MLC. Different mobile phase compositions were used for modelling based on retention times to obtain the best separation using central composite design. The optimum mobile phase composition for separation and determination of analytes in water samples was 69 mM SDS, 9% v/v 1-propanol and pH = 6.4. Recoveries were between 84.8–93.5% with relative standard deviation (RSD) less than 5.8% (n = 5). Limits of detection and linear range were 1–4.5 and 3.1–125.0 µg/L, respectively. The proposed method was applied to determine the aromatic amines in real samples (river and well waters). Amount of 4-nitroaniline and 3-nitroaniline in river water sample were 2.15 and 1.91 µg/L, respectively.     

Determination of antifungal proteins in soil by liquid chromatography

A liquid chromatography method was developed for the determination of antifungal/antimicrobial proteins Rs-AFP1 and Dm-AMP1 in sandy loam soils. The extraction of these highly basic proteins was achieved by mechanical shaking with aqueous Tris buffer pH 9 containing guanidinium thiocyanate salt (4.1 M), EDTA and nonionic polyoxyethylene 20 cetyl ether, Brij-58 detergent. The extracts were cleaned up on Oasis HLB polymer solid-phase extraction cartridges and quantified by liquid chromatography fluorescence detection based on the fluorescence properties of the tryptophan content of these proteins. The detector response was linear for 0.3-10 microg mL(-1). Procedural recoveries were tested in the range 10-100 mg kg(-1). The limit of quantification was 10 mg kg(-1 )protein in the soil sample representing the lowest validated fortification level. The antifungal proteins were found to be stable in soil extract tested up to 9 days when stored at 4 degrees C.     

Speciation of vanadium in soil

A method for speciation of vanadium in soil is presented in this work. The sequential extraction analysis procedure of Tessier et al. for heavy metals was used for the vanadium separation. The method consists of sequential leaching of the soil samples to separate five fractions of metals: (1) exchangeable, (2) bound to carbonates, (3) bound to Fe-Mn oxides, (4) bound to organic matter and (5) residual. The leaching solutions of Tessier were used for the vanadium extraction, only for the residual fraction the HClO₄ was replaced with H₂SO₄. The optimum conditions for leaching of vanadium from soil (weight of sample, concentration and volume of extractants, time of extraction) were chosen for each fraction. A sensitive, spectrophotometric method based on the ternary complex V(IV) with Chrome Azurol S and benzyldodecyldimethylammonium bromide (ε=7.1×10⁴ l mol⁻¹ cm⁻¹) was applied for the vanadium determination after separation of V(V) by solvent extraction using mesityl oxide and reduction of V(V) using ascorbic acid. This method was applied for vanadium speciation in soil from two different regions of Poland: Upper Silesia (industrial region) and Podlasie (agricultural region). The content of vanadium in the fractions of Upper Silesia soil was respectively (in 10⁻³%): I, 3.39; III, 4.53; IV, 10.70; V, 8.70 and it was the highest in the organic fraction, indicating input by anthropogenic activities. The content of vanadium in Podlasie soil was clearly lower and it was (in 10⁻³%): I, 2.07; III, 0.92; IV, 0.69; V, 1.23. The concentration of vanadium in fraction 2 of both soils was less than detection limit of applied method. The total content of vanadium in the five soil fractions was in good correlation with the total content of this element in both soils found after HF-H₂SO₄ digestion. Analysis using the ICP-AES method gave comparable results.     

Combination of micellar extraction and GC-ECD for the determination of polychlorinated biphenyls (PCBs) in water

 The application of the solvent-free micellar extraction as an alternative method to the liquid–liquid extraction for the enrichment of polychlorinated biphenyls (PCBs) from ultrapure and natural water is presented. A nonionic surfactant was used to preconcentrate the PCBs. After a clean-up consisting of two columns (silica gel and Florisil) the analytes were identified and quantified by GC-ECD. Recoveries for spiked water were up to 100%. For highly contaminated seepage water of landfills liquid–liquid extraction is involving great problems with the phase separation of water and solvent. According to our results, the micellar extraction is superior to the liquid–liquid extraction for this difficult kind of aqueous matrix. Received: 20 February 1996/Revised: 20 May 1996/Accepted: 30 May 1996     

Combination of micellar extraction and GC-ECD for the determination of polychlorinated biphenyls (PCBs) in water

 The application of the solvent-free micellar extraction as an alternative method to the liquid–liquid extraction for the enrichment of polychlorinated biphenyls (PCBs) from ultrapure and natural water is presented. A nonionic surfactant was used to preconcentrate the PCBs. After a clean-up consisting of two columns (silica gel and Florisil) the analytes were identified and quantified by GC-ECD. Recoveries for spiked water were up to 100%. For highly contaminated seepage water of landfills liquid–liquid extraction is involving great problems with the phase separation of water and solvent. According to our results, the micellar extraction is superior to the liquid–liquid extraction for this difficult kind of aqueous matrix. Received: 20 February 1996/Revised: 20 May 1996/Accepted: 30 May 1996     

AB-DTPA浸提-原子荧光法测定土壤中有效砷和有效硒

硒和砷是土壤中重要元素,目前关于提取测定有效硒和有效砷的报道还比较缺乏。本文采用原子荧光光谱法,以AB-DTPA为浸提剂,建立了一种准确测定本地区土壤中有效硒和有效砷的分析方法。通过考察浸提剂加入量,即土液比（m/v）;浸提时的振荡时间和振荡频率的影响,确立了适用于本地区土壤有效硒和有效砷提取分析的有效方法,结果表明：随着浸提剂的不断加入,所测土壤中有效硒和有效砷含量逐渐增大,当土壤称样量和浸提剂使用体积比为1:5时,所测土壤有效硒和有效砷含量最高,继续加入浸提剂后形成稀释效应导致测量结果偏低,故将土液比（m/v）定位1:5;当振荡时间不断增大时,所测所测土壤中有效硒和有效砷含量逐渐增大,振荡时间在30min时,浸提效果最佳,继续增加振荡时间到50min时对浸提效果影响不大,故将30min确立为最佳振荡时间;随着振荡频率的增大,有效硒和有效砷提取量逐渐增加,振荡频率在90-130r/min之间时,浸提效果最好,继续增大振荡频率,所测土壤中有效硒和有效砷含量变化不大。通过上述条件探索,选取五种土壤标准物质（GBW07441,GBW07442,GBW07443,GBW07444,GBW07445）进行验证,结果表明五种不同的土壤标准物质中有效硒和有效砷含量测定值准确,测定误差在-2.84~1.03mg/Kg,相对标准偏差为5.32%~8.85%,精密度和准确度均满足国家相关标准要求。     

Continuous microwave-assisted extraction, solvent changeover and preconcentration of monophenols in agricultural soils

An automatic extraction, preconcentration and clean-up module for the extraction of phenolic compounds from soils was developed; the separation and quantitation of each phenol is accomplished by GC-MS. The sorption-desorption of thirteen phenols on soils containing variable amounts of organic carbon (0.05-3.4%) and clay minerals (2-43%) at pH 5.7-8.6 was investigated. For this purpose, uncontaminated soils were spiked with 5 or 20 microg of each phenol per g of soil; the soils were then stored at 4 degrees C for at least 3 months prior to analysis in order to simulate analyte-matrix interactions other than material losses and environmental degradation in actual contaminated soils. The organic carbon content in acid and alkaline soils affects the sorption of chlorophenols but not that of alkylphenols. On the other hand, alkylphenols are preferentially sorbed by neutral soils, the process being influenced by the clay mineral content. Based on the results, alkylphenols interact more strongly with agricultural soils than do chlorophenols; also, both types of compound are less strongly sorbed by loamy sand soils owing to their increased sand contents.     

Phase behavior of a mixture of poly(isoprene)-poly(oxyethylene) diblock copolymer and poly(oxyethylene) surfactant in water

The phase behavior of a mixture of poly(isoprene)-poly(oxyethylene) diblock copolymer (PI-PEO or C250EO70) and poly(oxyethylene) surfactant (C12EO3, C12EO5, C12EO6, C12EO7, and C12EO9) in water was investigated by phase study, small-angle X-ray scattering, and dynamic light scattering (DLS). The copolymer is not soluble in surfactant micellar cubic (I1), hexagonal (H1), and lamellar (Lalpha) liquid crystals, whereas an isotropic copolymer fluid phase coexists with these liquid crystals. Although the PI-PEO is relatively lipophilic, it increases the cloud temperatures of C12EO3-9 aqueous solutions at a relatively high PI-PEO content in the mixture. Most probably, in the copolymer-rich region, PI-PEO and C12EOn form a spherical composite micelle in which surfactant molecules are located at the interface and the PI chains form an oil pool inside. In the C12EO5/ and C12EO6/PI-PEO systems, one kind of micelles is produced in the wide range of mixing fraction, although macroscopic phase separation was observed within a few days after the sample preparation. On the other hand, small surfactant micelles coexist with copolymer giant micelles in C12EO7/ and C12EO9/PI-PEO aqueous solutions in the surfactant-rich region. The micellar shape and size are calculated using simple geometrical relations and compared with DLS data. Consequently, a large PI-PEO molecule is not soluble in surfactant bilayers (Lalpha phase), infinitely long rod micelles (H1 phase), and spherical micelles (I1 phase or hydrophilic spherical micelles) as a result of the packing constraint of the large PI chain. However, the copolymer is soluble in surfactant rod micelles (C12EO5 and C12EO6) because a rod-sphere transition of the surfactant micelles takes place and the long PI chains are incorporated inside the large spherical micelles.     

高效液相色谱法分析环境样品中的苯基胂化合物

二苯氯胂和二苯氰胂是刺激性毒剂,在环境中易于降解,其产物苯胂酸、苯胂氧、二苯胂酸、氧联双二苯胂和三苯胂比较稳定,对环境危害大。建立了同时测定这5种含胂产物的反相高效液相色谱方法,选择了最佳色谱条件,提供了各组分的紫外光谱图。5种化合物的线性范围分别为8~30,5~40,20~4000,120~8000,1~60 mg/L,检测限分别为0.1,0.1,0.2,10,0.1 mg/L。对实际环境样品进行了分析,结果较好。     

煤直接液化油中混合酚的分离研究

利用分子筛择形特点，对煤直接液化油中的混合酚实施高效分离。本研究选取间甲酚和对甲酚作为分离煤直接液化油馏分段混合酚的模型化合物，采用化学液相沉积法对HZSM-5吸附剂的孔口结构进行改变，分析分子筛硅铝比及颗粒粒径对模型化合物间甲酚和对甲酚吸附分离性能的影响，以获得高性能固相吸附剂，并将其应用于180-190℃馏分段混合酚分离。结果表明，当分子筛硅铝比为25、粒径为3-5 μm时，分子筛的孔口结构调节效果最优；当正硅酸乙酯的最小用量为0.2 mL/g时，固相吸附剂的吸附量为0.03 g/g，对甲酚选择性高于95%。由于外表面沉积物对吸附剂的孔口结构变化，导致对甲酚选择性的提高。进一步采用HZSM-5（1）吸附剂对真实煤直接液化油混合酚的分离中发现，苯酚和对甲酚的选择性均达到100%。     

气相色谱-质谱联用鉴定基于水酶法制备的虹鳟鱼骨油组分

采用水酶法制备虹鳟鱼骨油,单因素分析法优化虹鳟鱼骨酶解的工艺条件,考察了料液比、pH值、酶解时间、酶解温度、加酶量5个因素对鱼油提取率的影响,采用气相色谱-质谱联用 (GC-MS) 技术对鱼骨油的脂肪酸组成和含量进行了分析鉴定.结果表明,在55℃、pH 7.5、酶解时间为3 h、料液比为1∶1、加酶量为2000 U/g的条件下,利用碱性蛋白酶提取的虹鳟鱼骨油中的油脂含量最高.GC-MS分析结果表明,虹鳟鱼骨油中主要成分是不饱和脂肪酸,含量为脂肪酸总量的80.4% (w/w),其中单不饱和脂肪酸和多不饱和脂肪酸分别约占不饱和脂肪酸的76.9%和23.1% (w/w), DHA和EPA的总量为3.4% (w/w).本研究优化了虹鳟鱼油的提取技术,对虹鳟鱼油的主要挥发性物质进行了分析鉴定,初步确定了其中对鱼油风味起主要贡献的物质,对鱼油产品的分析与鉴别具有参考价值.     

Establishment of an immunoaffinity chromatography for simultaneously selective extraction of Sudan I, II, III and IV from food samples

The establishment of an immunoaffinity chromatography (IAC) for simultaneously selective extraction of four illegal colorants Sudan dyes (Sudan I, II, II and IV) from food samples was described. The IAC column was constructed by covalently coupling monoclonal antibody (mAb) against Sudan I to CNBr-activated Sepharose 4B and packed into a common solid phase extraction (SPE) cartridge. It was observed that IAC column was able to separately capture Sudan I, II, III and IV with maximum capacity of 295, 156, 184 and 173ng, respectively. The extraction conditions including loading, washing and eluting solutions were carefully optimized. Under optimal conditions, the extraction recoveries of the IAC column for Sudan I-IV at two different spiked concentrations were within 95.3-106.9%. After 50 times repeated usage, 64% of the maximum capacity was still remained. Six food samples randomly collected from local supermarket without spiking Sudan dyes were extracted with IAC column and detected by high performance liquid chromatography (HPLC). It was found that there was no detectable Sudan II, III and IV in all six food samples, but Sudan I with the content of 2.7-134.5ngg(-1) was detected in three food samples. To further verify the extraction efficiency, other three negative samples were spiked with Sudan I-IV at the concentrations of 20ngg(-1) and 50ngg(-1), which were then extracted with IAC column. The extraction recoveries and relative standard deviation (RSD) were 68.6-96.0% and 4.8-15.2%, respectively, demonstrating the feasibility of the prepared IAC column for Sudan dyes extraction.     

Determination of thallium in soils by flame atomic absorption spectrometry

A method is described for the determination of Tl in soils by FAAS, involving extraction of Tl from 5 g of soil by digestion with HClO₄/HNO₃ followed by separation of the extracted Tl into 5 mL of diisopropylether from HBr solution, including Ce(SO₄)₂. Tl in the organic phase is determined by direct aspiration into the spectrophotometer. The percentage relative standard deviation (% RSD) for 5 replicate samples is about 1%. The detection limits (S/N = 3) of this method are 0.001 mg/L for aqueous solution and 0.02 mg/kg DW for soil, when 50 mL of soil solution corresponding to 2.5 g soil are used. The Tl concentration even of unpolluted soils can be determined. The method was shown to be unaffected by the presence of various ions in soil and was able to recover nearly 100% Tl added to soils. The arithmetic mean (range) of 18 Japanese unpolluted surface soils was 0.33 (0.10–0.56)mgTl/kg DW.     

Determination of N-nitroso derivatives of hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) in soils by pressurized liquid extraction and liquid chromatography-electrospray ionization mass spectrometry

To aid in the evaluation of the potential toxicity of N-nitroso derivatives of hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), we describe a pressurized liquid extraction (PLE) followed by liquid chromatography-electrospray ionization-mass spectrometry (LC-ESI-MS) method for determination of RDX and its N-nitroso derivatives: hexahydro-1-nitroso-3,5-dinitro-1,3,5-triazine (MNX), hexahydro-1,3-dinitroso-5-nitro-1,3,5-triazine (DNX), and hexahydro-1,3,5-trinitroso-1,3,5-triazine (TNX) in soils. Sandy loam soil was spiked with RDX and its N-nitroso derivatives (MNX, DNX, and TNX). Acetonitrile was used as the PLE extraction solvent at 100 degrees C and 1500 psi for 15 min. Florisil was used to cleanup extracts following PLE. Instrumental analysis employed LC-ESI-MS, in which 1mM acetic acid was added to the mobile phase to facilitate formation of acetate adduct ions [M+CH(3)COO](-). The method detection limits (MDLs) for RDX, MNX, DNX, and TNX were 1.46, 1.46, 1.69, and 1.93 ng/g, respectively. High recovery (91.1-108.3%), good precision (RSD: 3.2-12.4%), and reproducibility were achieved. This method proved effective and was applied to monitor the reductive biotransformation of MNX in soils with the presence of earthworms (Eisenia fetida).     

Liquid chromatographic determination of triasulfuron in soil

Two extraction methods were developed for the determination of triasulfuron in soil. Method I included extraction with methanol-phosphate buffer at pH 7 (2 + 1, v/v), liquid-liquid partition with dichloromethane, and cleanup on a liquid chromatographic Si adsorption solid-phase extraction tube. In Method II, Extrelut was added and the sample was then extracted with acetonitrile. In both cases, the extracts were analyzed by liquid chromatography (LC) with UV detection and the LC peak was confirmed by LC/mass spectrometry (MS). The 2 methods were tested on 3 soils having different physicochemical characteristics. Method I gave 83% average recovery and a determination limit of 0.4 microg/kg soil. Method II gave 67% average recovery and a determination limit of 2 microg/kg soil. Examples of application of Method I to field samples are reported.     

How can temperature affect reverse micellar extraction using sucrose fatty acid ester?

The reverse micellar extraction of lysozyme using sucrose fatty acid ester was found to be greatly affected by the temperature in the extraction process. For example, lysozyme was perfectly extracted from the feed aqueous phase to the reverse micellar organic phase at 25°C, while it was not extracted at 5°C at all. After entrapping lysozyme into the reverse micelles, lysozyme was recovered from the reverse micellar organic phase to the recovery aqueous phase only by decreasing the temperature in the backward extraction. Moreover, lysozyme solubilized in the reverse micellar organic solution could be recovered without the recovery aqueous solution at 3°C, and its activity was retained at 95%.     

Retention modelling in liquid chromatographic separation of simvastatin and six impurities using a microemulsion as eluent

A novel and unique approach was used for retention modelling in the separation of simvastatin and six impurities by liquid chromatographic using a microemulsion as mobile phase. A microemulsion is a modification of a micellar system where a lipophilic organic solvent is dissolved in the micelles; for that reason, microemulsions are usually treated as solvent-modified micellar solutions. When microemulsions are used as eluents in HPLC separations, solutes partition between the charged oil droplets and the aqueous buffer phase. The complexity of the composition of the microemulsion permits extensive manipulations to be made during method development in order to achieve acceptable resolution of such a complex mixture of substances. In order to avoid a laborious "trial and error" procedure, a 2(3) full factorial design was applied for choosing an optimal microemulsion composition to obtain good separation in a reasonable run time. Organic solvent, sodium dodecyl sulphate, and n-butanol content were varied within defined experimental domain. Optimal conditions for the separation of simvastatin and its six impurities were obtained using an X Terra 50 x 4.6 mm, 3.5 microm particle size column at 30 degrees C. The mobile phase consisted of 0.9% w/w of diisopropyl ether, 2.2% w/w of sodium dodecylsulphate (SDS), 7.0% w/w of co-surfactant such as n-butanol, and 89.9% w/w of aqueous 25 mM disodium phosphate pH 7.0.     

以TTA—TBPO为协同流动载体的液膜法富集钪(Ⅲ)

提出用TTA-TBPO为协同流动载体的乳状液膜分离它集抗（Ⅲ）的方法。其最佳液膜体系的组成为4％Span80.5％TTA、3％TBPO、4％液体石蜡、84％煤油和内相水溶液（4mol/L），最优实验条件，提取钪（Ⅲ）的外相试液为pH=1．3～2．3，Roi（油内比）为1：1，Rew（乳水比）为20：100。本法用于分离富集稀土元素中的微量钪（Ⅲ），其回收率可达99．1％以上，相对标准偏差为3．5％以下，结果十分满意。