高价小分子型分散剂在Al2O3表面的吸附研究

采用5-硝基水杨酸合铁()分光光度法测定了2-膦酸丁烷-1,2,4-三羧酸(PBTCA)及柠檬酸在Al₂O₃表面的等温吸附线,发现二者的饱和吸附量均随pH值的升高而减小,且PBTCA比柠檬酸的饱和吸附量高.ζ电位及沉降实验亦表明,与柠檬酸相比,PBTCA的吸附使Al₂O₃表面的有效负电荷量更高,且其分散作用也更佳.采用FTIR及AES研究了PBTCA在Al₂O₃表面的吸附机理.膦酸基的存在提高了PBTCA在碱性条件下的吸附能力.     

NOx/CO2/H2O在BaO(001)表面吸附的理论研究

采用密度泛函理论(DFT)研究了NOx/CO2/H2O在BaO(001)表面不同覆盖度下的吸附情况.计算表明NO以N端吸附在表面氧位,形成NO22-吸附物种;CO2以C端吸附在表面氧位,形成表面CO32-;而H2O在表面发生解离吸附,导致BaO表面的羟基化.NO2有两种主要的吸附模式:以N端吸附在表面氧位,或以O端吸附表面Ba位.各物种在表面的吸附顺序为:NO≈H2O相似文献   

Zr掺杂对La（Ba）ZrxCo1-xO3-δ钙钛矿催化N2O分解性能的影响（英文）

采用溶胶凝胶法制备了Zr掺杂的钴基钙钛矿La(Ba)ZrxCo1-xO3-δ,并将其用于航天推进剂领域的高浓度N2O催化分解反应.发现Zr的引入明显提高了钙钛矿La(Ba)ZrxCo1-xO3-δ的催化活性,尤其是当Zr掺杂量分别为0.05和0.2时,LaZrxCo1-xO3-δ和BaZrxCo1-xO3-δ催化剂性能较为优异.应用N2物理吸附、X射线衍射、H2程序升温还原、O2程序升温脱附和氧脉冲吸附技术表征了Zr掺杂对La(Ba)ZrxCo1-xO3-δ催化剂的物化性质的影响.结果表明,Zr掺杂增大了钴基钙钛矿的比表面积,改善了晶格结构,从而提高了钴物种的还原及氧吸附脱附能力,因而催化剂上N2O分解活性增加.     

Zr掺杂对La(Ba)Zr_xCo_(1-x)O_(3-δ)钙钛矿催化N_2O分解性能的影响(英文)

采用溶胶凝胶法制备了Zr掺杂的钴基钙钛矿La(Ba)ZrxCo1-xO3-δ,并将其用于航天推进剂领域的高浓度N2O催化分解反应.发现Zr的引入明显提高了钙钛矿La(Ba)ZrxCo1-xO3-δ的催化活性,尤其是当Zr掺杂量分别为0.05和0.2时,LaZrxCo1-xO3-δ和BaZrxCo1-xO3-δ催化剂性能较为优异.应用N2物理吸附、X射线衍射、H2程序升温还原、O2程序升温脱附和氧脉冲吸附技术表征了Zr掺杂对La(Ba)ZrxCo1-xO3-δ催化剂的物化性质的影响.结果表明,Zr掺杂增大了钴基钙钛矿的比表面积,改善了晶格结构,从而提高了钴物种的还原及氧吸附脱附能力,因而催化剂上N2O分解活性增加.     

Ru/Ba-ZrO2催化剂的制备及其氨合成性能研究

分别采用柠檬酸络合法、改性共沉淀法和湿浸渍法制备了掺Ba纳米ZrO2材料,负载Ru后用于催化氨合成反应.采用X射线衍射、CO2程序升温脱附(CO2-TPD)、N2物理低温吸附、H2程序升温还原技术(H2-TPR)、扫描电镜(SEM)、透射电镜(TEM)、X射线光电子能谱(XPS)和CO化学吸附对载体材料和催化剂进行了表征.结果表明,不同方法制备载体的物相结构和织构性能均有明显差别,负载Ru后催化剂的氨合成性能差别也较大.其中,以柠檬酸络合法制备的载体材料中Ba以BaZrO3的形式存在,钙钛矿型BaZrO3具有较强的供电子能力,电子可以通过Ru与载体间强相互作用传递到Ru表面,有效地促进N≡N的断裂,使催化剂的低温活性显著提高.在425℃,3 MPa,空速为10000 h-1条件下,出口氨浓度为5.72%.其氨合成活性分别是改性共沉淀法和湿浸渍法制备催化剂的3.8倍和14.3倍.     

CuO-ZnO-ZrO2的柠檬酸燃烧法制备及其催化CO2加氢合成甲醇的性能

采用柠檬酸燃烧法制备了CuO-ZnO-ZrO2(CZZ)催化剂,并将其用于CO2加氢合成甲醇反应.按推进剂化学原理对燃烧反应进行了分析,并采用热重-差热分析(TG-DTA)技术记录了其燃烧行为.采用X射线衍射(XRD)、氮吸附、程序升温还原(TPR)及氧化亚氮(N2O)反应吸附技术对制得的催化剂进行了表征.结果表明:柠檬酸燃烧法的燃烧过程比较温和,燃料用量对催化剂物化和催化性能的影响不大,并结合燃烧反应的特点进行了解释.此外,还对三种燃料(柠檬酸、尿素和甘氨酸)的用量与CZZ性能之间的关系进行了比较,表明柠檬酸作燃料具有更好的工艺可控性.柠檬酸燃烧法是一种简单、快速且有效的制备CZZ催化剂的方法.     

碱土金属对锆基钙钛矿材料负载钌催化剂氨合成性能的影响

采用柠檬酸络合法制备了含Ca,Sr和Ba的锆基钙钛矿材料,负载Ru后用于催化氨合成反应;研究了碱土金属对催化剂织构性能和载体材料表面碱性的影响,并与催化剂活性相关联.同时,采用程序升温脱附技术对催化剂表面H2脱附性能进行了表征.结果显示,碱土金属对催化剂活性的促进顺序为Ba>Sr>Ca.研究发现,不同锆基碱土金属钙钛矿材料表面均具有较强的碱性位,碱土金属的加入影响了载体碱性强度以及金属-载体的相互作用,其中BaZrO3可有效抑制H2的吸附.因此,Ru/BaZrO3催化剂表现出优异的氨合成活性.     

BaX分子筛的阳离子分布及其吸附分离对二甲苯的机理

 BaX分子筛是用于从C8芳烃中分离高纯度对二甲苯的吸附剂. 应用多晶XRD技术,通过电子密度函数法和Rietveld法,对吸附速率和分离度不同的两个BaX分子筛样品进行了结构的测定,并通过结构分析探讨了BaX分子筛的吸附机理. 结果表明,不同工艺制备的BaX分子筛中Ba2+离子的定位略有不同. BaX分子筛中Ba2+离子主要分布在SⅠ′ 和SⅡ位置上,定位于SⅠ′ 位的Ba2+离子稳定了分子筛的骨架; 而定位于超笼的SⅡ位置的Ba2+离子,当其接近占满并且每个Ba2+极化两个配位水时,可在超笼中产生一个对称性为D2群的吸附力场,这是BaX分子筛吸附分离对二甲苯的必要条件. 若Ba2+离子在SⅡ位置的占有率下降或在超笼中存在着SⅡ位置以外的低占有率的阳离子,则破坏了上述吸附力场的对称性,削弱了分子筛的选择吸附能力.     

碳纳米管-氧化铝:高抗硫及再生性能的Pt基催化剂载体及在NO_x还原反应中的应用(英文)

通过乙炔在Al2O3上的分解制备碳纳米管-氧化铝(Al2O3-CNTs)载体.采用浸渍法,分别制备了Pt/Ba/Al2O3-CNTs和Pt/Ba/Al2O3催化剂.利用XRD,SEM,TEM,低温N2物理吸附,XPS和in-situ DRIFTS等手段对催化剂的物化性质进行了表征.结果表明,在SO2存在下的NOx还原反应中,Pt/Ba/Al2O3-CNTs比Pt/Ba/Al2O3具有更高的抗SO2性能和再生性能.In-situ DRIFTS表明SO2的存在对NOx储存还原的途径没有影响.     

柠檬酸对Ru/AC氨合成催化剂结构和活性的影响

使用柠檬酸(CA)修饰石墨化活性炭(AC)和钌以改善Ru/AC催化剂中钌粒子的尺寸分布和催化剂的活性, 并通过透射电镜(TEM)、热重分析(TGA)、CO化学吸附和N2物理吸附等方法研究了柠檬酸对AC和Ru/AC催化剂织构、钌的分散度和催化剂的活性等性质的影响. 结果表明, 负载的柠檬酸优先吸附于活性炭微孔, 少量柠檬酸即可大幅度降低活性炭的比表面积, 增加活性炭表面含氧官能团的数量, 改善了钌粒子分布. 最佳负载顺序是柠檬酸和氯化钌依次负载. 在活性炭中添加适量的柠檬酸对催化剂的低温活性有显著影响. 柠檬酸处理后的Ru/AC催化剂活性最大提高幅度为21.4%.     

制备方法对Ni/CeO2-Al2O3催化剂甲烷部分氧化催化性能的影响

采用浸渍-沉淀法、水热合成法、共沉淀法和柠檬酸络合法制备了Ni/CeO₂-Al₂O₃催化剂,考察了制备方法对该催化剂的物理结构和甲烷部分氧化(POM)催化性能的影响。利用N₂物理吸附、X射线粉末衍射(XRD)、H₂-程序升温还原(H₂-TPR)、NH₃-程序升温脱附(NH₃-TPD)、热重(TG)分析等手段对反应前后催化剂的物理化学性质进行了表征。实验结果表明,浸渍-沉淀法制备催化剂的活性和产物H₂和CO的选择性最低。而柠檬酸络合法制备的Ni/CeO₂-Al₂O₃表现出最大的CH₄转化率和最高的CO、H₂选择性。BET和XRD表征结果表明,柠檬酸络合法制备的Ni/CeO₂-Al₂O₃的比表面积最大,且CeO₂晶粒粒径小、分散均匀;H₂-TPR测试表明,该催化剂负载的Ni物种和Ni与Al₂O₃相互作用产生的尖晶石NiAl₂O₄都较容易被还原成金属Ni,产生更多的活性中心;NH₃-TPD和TG分析表明,该催化剂具有较多酸性位点和表面积炭,但相比较于它的高反应活性,积炭速率较低、稳定性较高。     

Interaction between low molecular weight organic acids and hydroxyapatite with different degrees of crystallinity

In this study, two types of hydroxyapatite (HAP) with different degrees of crystallinity were prepared by a sol-gel method and a chemical precipitation method. Influences of crystallinity on the adsorption and dissolution properties of HAP, and the release of phosphorus (total phosphorus) during the adsorption of organic acid were investigated. Results showed that crystallinity had a great effect on the adsorption capacity and dissolution properties of HAP, as well as the adsorption mechanisms of organic acids on HAP surfaces. The poorly crystallized (the degree of crystallinity X_c = 0.23) HAP adsorbed greater amounts of oxalic, citric, or malic acid than the well crystallized (X_c = 0.86) HAP, and the former could release more phosphorus in the presence of organic acids. The adsorption capacity of oxalic acid was much higher than citric and malic acids on both the well and the poorly crystallized HAP, which was due to the strong coordination of oxalic acid with calcium on HAP surface, and that physical adsorption was more inclined to dominate the adsorption of malic or citric acid on the well crystallized HAP. These findings might be of importance in understanding the effects of crystallinity and organic acid binding on the dissolution of calcium phosphates and the adsorption characteristics of HAP.     

Effects of Citric Acid Concentration and Activation Temperature on the Synthesis of Carbon Nanotubes

A series of Ni-La-Mg catalyst samples were prepared by citric acid complex method, and carbonnanotubes were synthesized by catalytic decomposition of CH4 on these catalysts. The effects of the citricacid concentration and the activation temperature on catalytic activity were investigated by CO adsorption,TEM and XRD techniques. The experimental results showed that the particle size of the catalysts preparedthrough gel auto-combustion varied with the concentration of citric acid. Therefore carbon nanotubes with different diameters were obtained correspondingly. The effect of activation temperature on the activity of catalyst was negligible from 500 to 700℃, but it became pronounced at lower or higher temperatures.     

无溶剂高度分散Ni/MCM-41催化剂的制备及其萘加氢性能

分别用机械研磨无溶剂法、添加柠檬酸无溶剂法制备了Ni/MCM-41催化剂,对所制催化剂进行了分析表征,探究其萘加氢反应性能并与常规浸渍法进行了对比。与常规浸渍法相比,机械研磨无溶剂法所制催化剂的物理性质相近,金属镍分散度和萘加氢性能略有提高;添加柠檬酸无溶剂法则显著提升了催化剂的分散度和萘加氢性能,金属镍分散度由6.9%大幅提高至67.9%,萘加氢性能提高了近1倍。通过红外光谱、紫外光谱和热重分析,提出了添加柠檬酸对无溶剂法制备催化剂性能的促进作用机制。     

Improved Cellulose Adsorption Method for the Preparation of Perovskite Oxides with Large Specific Surface Area at Low Temperature

Wet chemical methods have lots of advantages over the traditional solid state reaction for the synthesis of mixed oxides1. In this letter, we report the preparation of La1-xSrxMO3-( (x=0,0.1,0.2, M=Co,Fe,Mn) functional oxide powders by improved cellulose adsorption method, i.e., pyrolysis of metal salt(-organic acid)-cellulose compounds, which takes both the advantages of Pechini method (high surface area and low pyrolysis temperature) and cellulose adsorption method (simplicity). Several m…     

Modeling the adsorption of Cd(II) onto goethite in the presence of citric acid

The adsorption of cadmium onto goethite in the presence of citric acid was measured as a function of pH and cadmium concentration at 25 degrees C. Potentiometric titrations were also performed on the system. Cadmium adsorption onto goethite was enhanced above pH 4 in the presence of 50 microM, 100 microM and 1 mM citric acid. While there was little difference between the enhancements caused by 50 and 100 microM citric acid below pH 6, above pH 6 further enhancement is seen in the presence of 100 microM citric acid. When 1 mM citric acid was present, the enhancement of cadmium adsorption was greater below pH 6, with increased Cd(II) adsorption down to pH 3.5. However, above pH 6, 1 mM of citric acid caused slightly less enhancement than the lower citric acid concentrations. ATR-FTIR spectra of soluble and adsorbed citrate-cadmium species were measured as a function of pH. At pH 4.6 there was very little difference between the ternary Cd(II)-citric acid-goethite spectrum and the binary citric acid-goethite spectrum. However, spectra of the ternary system at pH 7.0 and 8.7 indicated the presence of additional surface species. Further analysis of the spectra suggested that these were metal-ligand outer-sphere complexes. Data from the adsorption experiments and potentiometric titrations of the ternary Cd(II)-citric acid-goethite system were fitted by an extended constant-capacitance surface complexation model. The spectroscopic data were used to inform the choice of surface species. Three reactions in addition to those for the binary Cd(II)-goethite and citric acid-goethite systems were required to describe all of the data. They were [formula in text], [formula in text], and [formula in text]. Neither the spectroscopy nor the modeling suggested the formation of a ternary inner-sphere complex or a surface precipitate under the conditions used in this study.     

柠檬酸盐凝胶法制备纳米CuO-ZnO-ZrO_2的工艺分析及CO_2加氢制甲醇的性能

采用柠檬酸盐凝胶法制备出纳米CuO-ZnO-ZrO_2(CZZ)催化剂,应用XPS、BET、XRD、H_2-TPR、H_2-TPD、CO_2-TPD和TG-DTA等检测手段对催化剂及前驱体的结构进行表征。研究了湿凝胶干燥时间和柠檬酸用量对催化剂结构的影响,并与燃烧法制得的催化剂进行对比,考察了不同催化剂CO_2加氢制甲醇的性能。研究表明,延长湿凝胶干燥时间可有效防止催化剂焙烧时发生喷溅,有利于催化剂中各组分的分散,提高催化剂对H_2和CO_2的吸附能力;112℃干燥48h制得的催化剂(CZZ-48h)BET比表面积为43.5m~2/g,高于燃烧法;柠檬酸用量等于化学计量比时催化剂的性能最佳,在240℃、2.6MPa、空速为3600h-1、H_2/CO_2(体积比)为3的条件下甲醇时空收率达109.4g/(kg·h);柠檬酸过量会影响催化剂组分的分散度,并造成分解残留覆盖催化剂表面活性位而不利于CO_2加氢反应。     

Adsorption of citrate ions on hydroxyapatite synthetized by various methods

The specific adsorption of citric acid ions at hydroxyapatite interface was investigated by the means of radioisotope method (¹⁴C) as a function of citric acid ions concentration, NaCl concentration and pH. Application of the hydroxyapatite has become wide in the biomaterial field as the Ca₁₀(OH)₂(PO₄)₆ possess biocompatibility with human hard tissue. Hydroxyapatite was synthesized using three different methods. The physical properties of the resulting powder were characterized by DTA/TG, XRD, AFM and SEM microscopy. Physicochemical qualities characterizing the electrical double layer of the hydroxyapatite/NaCl solution interface were determined. The zeta potential and the adsorption of citric acid molecule were studied as a function of pH. The point of zero charge and the isoelectric point of samples were determined. Electrical double layer parameters of hydroxyapatite/NaCl interface are influenced by a synthesis method. The points pH_pzc and pH_IEP for sample 1 are pH_pzc 7.5 and pH_IEP 3; for sample 2 pH_pzc 7.05 and pH_IEP 3, for smaple 3 pH_pzc 6.7 and pH_IEP 3. Temperature has weak influence both on pure substance and with citric acid adsorbed, as derivatographic analysis has shown, and characterization of hydroxyapatite structure may be carried out by this thermal analysis. Two phenomena are responsible for citric acid adsorption: phosphate group’s replacement at hydroxyapatite surface by citric ions parallel to intraspherical complexes formation.     

聚苯乙烯包覆Y_2O_3:Eu~(3 )颗粒及表征

采用柠檬酸表面修饰 Y2 O3:Eu3 颗粒 ,苯乙烯乳液聚合的方法 ,制备出核 -壳型的 Y2 O3:Eu3 /聚苯乙烯颗粒 .在 FTIR谱图上 ,羰基伸缩振动峰向低波数位移 ;在 XPS谱图上 ,Y3d5 / 2 的电子结合能向高能方向移动 ,表明柠檬酸和颗粒表面发生键合作用 .说明此过程符合吸附层媒介作用机理 :柠檬酸使颗粒表面变成两亲性 ,从而使苯乙烯可吸附在颗粒表面形成包覆无机核的乳液结构 .EDS谱图表明聚苯乙烯均匀地包覆在颗粒表面