Effect of Li excess content and Ti dopants on electrochemical properties of LiFePO<Subscript>4</Subscript> prepared by thermal reduction method

Carbon coated Li_{1 + x} FePO₄ (x = 0, 0.01, 0.02, 0.03, 0.04) and doped compositions Li_1.03Fe_0.99Ti_0.01PO₄ have been synthesized by thermal reduction method in this paper. The results showed that increasing the content in Li_{1 + x} FePO₄ result in better electrochemical properties and cyclic performances until x = 0.03, which had similar change law with the particle size of samples; and the initial discharge capacity and cycle life of Li_1.03Fe_0.9Ti_0.01PO₄ was better than other samples under 1 C rate. When the Li_1.03Fe_0.99Ti_0.01PO₄/C sample cycled before 60 times, this sample exhibited a trend of increased capacity, and reached the highest discharging rate capacity of 156 mA h g⁻¹ at 60 cycles. The electrochemical performances of LiFePO₄ compositions synthesized by thermal reduction method, to some extent, can be improved by Li excess content and Ti doping.     

Preparation and electrochemical properties of Li<Subscript>0.97</Subscript>Er<Subscript>0.01</Subscript>FePO<Subscript>4</Subscript>/C composite for lithium-ion batteries

Li_0.97Er_0.01FePO₄/C composite was prepared by solid-state reaction, using particle modification with amorphous carbon from the decomposition of glucose and lattice doping with supervalent cation Er³⁺. All samples were characterized by X-ray diffraction, scanning electron microscopy, multi-point Brunauer Emmett and Teller methodes. The electrochemical tests show Li_0.97Er_0.01FePO₄/C composite obtains the highest discharge specific capacity of 154 mAh g⁻¹ at C/10 rate and the best rate capability. Its specific capacity reaches 131 mAh g⁻¹ at 2C rate. Its capacity loss is only 14.9 % when the rate varies from C/10 to 2C.     

Polyethylene Glycol for LiFePO<Subscript>4</Subscript>/C Composites Preparation: Large or Small Molecular Weight

Olivine LiFePO₄ is challenged by its poor electronic and ionic conductivities for lithium-ion batteries. Polyethylene glycol (PEG) has been applied for LiFePO₄ preparation by different research groups, but there is no consensus on the influence of the mean molecular weight of PEG on the structure and electrochemical performances of LiFePO₄/C composites. In this work, LiFePO₄/C composites were prepared by using micronsized FePO₄·2H₂O powder as starting material, PEG (mean molecular weight of 200, 400, 4000 or 10000) and citric acid as complex carbon source. The structure and electrochemical performances of LiFePO₄/C composites would be decided considerably by the mean molecular weight of PEG, and the sample using PEG200 exhibited the least inter-particle agglomeration, the smallest charge transfer resistance and the highest discharge capacity. A probable growth mechanism is also proposed based on SEM images and electrochemical results: with the assistance of citric acid, PEG molecule with small molecular weight tends to cover one or only a few micron-sized FePO₄·2H₂O particles, significantly suppress the agglomeration of primary LiFePO₄ particles and thus result in uniform particle-size distribution and carbon coating.     

Preparation and characterization of LiFePO<Subscript>4</Subscript> from NH<Subscript>4</Subscript>FePO<Subscript>4</Subscript>·H<Subscript>2</Subscript>O under different microwave heating conditions

Olivine-type LiFePO₄ is a very promising polyanion-type cathode material for lithium-ion batteries. In this work, LiFePO₄ with high specificity capacity is obtained from a novel precursor NH₄FePO₄·H₂O via microwave processing. The grains grow up in the duration of sintering until they reach the decomposition temperature. The apparent conductivity of the samples rises rapidly with the irradiation time and influences the electrochemical performance of the material greatly at high current density. As a result, the LiFePO₄ cathode material obtained with a sintering time of 15 min has good electrochemical performance. Between 2.5 and 4.2 V versus Li, a reversible capacity is as high as 156 mAh g⁻¹ at 0.05 C.     

Effects of carbon coating from sucrose and PVDF on electrochemical performance of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>/C composites in different potential ranges

The carbon coated nanoflower-like Li₄Ti₅O₁₂/C composites were prepared via hydrothermal method followed by surface modification using sucrose or polyvinylidene fluoride (PVDF) as carbon sources. X-ray diffraction, SEM, TEM, Raman spectroscopy, TGA, and the electrochemical measurements were used for the materials characterization. Such modification leads to the formation of a high-conductive carbon coating. In the case of polyvinylidene fluoride use, fluorination of Li₄Ti₅O₁₂ surface takes place also. As a result, electrochemical performance of the obtained composites is improved. In the potential range of 1–3 V, Li₄Ti₅O₁₂, Li₄Ti₅O₁₂/C_PVDF, and Li₄Ti₅O₁₂/C_sucrose exhibit, respectively, the discharge capacities of 142.5, 154.3, and 170.4 mAh/g at a current of 20 mA/g and 57.2, 82.1, and 89.3mAh/g at a current of 3200 mA/g. When cycled in a potential range of 0.01–3 V, the discharge capacity of Li₄Ti₅O₁₂/C_PVDF increases up to 252 mAh/g at 20 mA/g.     

Electrospun Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>/Li<Subscript>2</Subscript>TiO<Subscript>3</Subscript> composite nanofibers for enhanced high-rate lithium ion batteries

Li₄Ti₅O₁₂/Li₂TiO₃ composite nanofibers with the mean diameter of ca. 60 nm have been synthesized via facile electrospinning. When the molar ratio of Li to Ti is 4.8:5, the Li₄Ti₅O₁₂/Li₂TiO₃ composite nanofibers exhibit initial discharge capacity of 216.07 mAh g^?1 at 0.1 C, rate capability of 151 mAh g^?1 after being cycled at 20 C, and cycling stability of 122.93 mAh g^?1 after 1000 cycles at 20 C. Compared with pure Li₄Ti₅O₁₂ nanofibers and Li₂TiO₃ nanofibers, Li₄Ti₅O₁₂/Li₂TiO₃ composite nanofibers show better performance when used as anode materials for lithium ion batteries. The enhanced electrochemical performances are explained by the incorporation of appropriate Li₂TiO₃ which could strengthen the structure stability of the hosted materials and has fast Li⁺-conductor characteristics, and the nanostructure of nanofibers which could offer high specific area between the active materials and electrolyte and shorten diffusion paths for ionic transport and electronic conduction. Our new findings provide an effective synthetic way to produce high-performance Li₄Ti₅O₁₂ anodes for lithium rechargeable batteries.     

Chelation-assisted method for the preparation of cathode material LiFePO<Subscript>4</Subscript>

LiFePO₄/C composite cathode material is prepared by ball milling with the assistance of EDTA chelation with using water as the media of ball mill procedure. FePO₄ and LiOH are used as starting materials; a certain amount of glucose is used as carbon sources and reduction agent. The structure and morphology of the composite are characterized by X-ray diffraction and scanning electron microscopy. Cyclic voltammetry, AC impedance measurements, and galvanostatic charge–discharge and cycling performances are used to characterize its electrochemical properties. The results indicate that the performances of composites prepared by chelation-assisted method are much better than common ball milling method which using alcohol or acetone as the media of ball mill procedure. The stable discharge capacity of the prepared composite is 150 and 105 mAh g⁻¹ at 1 and 10 C rate, respectively.     

Pouch-typed cell from Li-rich LiFePO<Subscript>4</Subscript> prepared by low-cost carbothermal reduction method

Lithium iron phospho-olivine cathode material with optimized lithium amount for lithium-ion batteries was successfully prepared from low cost Fe₂O₃ as raw materials by thermal reduction method. The as-obtained material showed a reversible discharge capacity of 153.8 mAh g^–1 in the voltage window of 2.0–4.2 V at half-cell level. The pouch-typed cells with prepared Li_1.05FePO₄ were assembled to investigate electrochemical performance at level of full-cell. The results show that the assembled pouch-typed full-cells present better rate capability and cycle life. The low-cost approach reported here firstly sheds light on application of mass production of olivinestructured LiFePO₄ at level of full-cell.     

Effects of molecular weight,heating rate,synthetic temperature and sintering duration on electrochemical properties of a LiFePO<Subscript>4</Subscript>/C cathode material pyrolyzed from lithium polyacrylate

A LiFePO₄/C composite was obtained by a polymer pyrolysis reduction method, using lithium polyacrylate (LiPAA) as carbon source and fractional lithium source, and FePO₄·2H₂O as iron and phosphorus source. The structure of the LiFePO₄/C composites was investigated by X-ray diffraction (XRD). The micromorphology of the precursors and LiFePO₄/C powders was observed using scanning electron microscopy (SEM). Laser particle analyzer and BET were also used to characterize the materials. It was found that the micromorphology, particle size distribution and specific surface area of LiFePO₄/C composites were greatly influenced by the molecular weight of LiPAA. The electrochemical properties of the LiFePO₄/C composites were evaluated by cyclic voltammograms (CVs), electrochemical impedance spectra (EIS) and constant current charge/discharge cycling tests. The results showed that the molecular weight of LiPAA, heating rate, synthetic temperature and sintering duration directly affected the electrochemical properties of LiFePO₄/C composites. The sample with the optimized electrochemical properties were obtained in the following conditions, i.e., LiPAA with the molecular weight of 20,000, heating rate of 10 °C min⁻¹, synthetic temperature of 700 °C and sintering duration of 15 h.     

Effect of starting materials on electrochemical performance of sol-gel-synthesized Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode materials for lithium-ion batteries

In this study, the effect of the sol-gel starting materials with different particle sizes on the sol-gel-synthesized spinel Li₄Ti₅O₁₂ (LTO) was systematically investigated. The physical and electrochemical properties of the synthesized materials were characterized by X-ray diffraction, scanning electron microscopy, Brunauer-Emmett-Teller-specific surface area analyses, galvanostatic charge/discharge tests, cyclic voltammetry, and electrochemical impedance spectroscopy. It was found that the initial particle size of sol-gel starting material played a crucial role on the properties of as-prepared LTOs. The LTO synthesized with the relatively finer particle size of starting materials possessed relatively smaller particle size and larger specific surface area and therefore resulted in the superior electrochemical properties. The initial discharge capacity of the as-prepared LTO exhibited 168.2, 150.6, and 142.7 mAh g^?1 at current densities of 1, 5, and 10 C, respectively, and up to 95, 95, and 90 % of the corresponding initial discharge capacity was retained after 50 cycles.     

LiFePO4的软化学合成及锂快离子导体修饰

采用溶剂热法制备正极材料LiFePO_4,采用溶胶凝胶法制备Li_(0.5)La_(0.5)TiO_3(LLTO)粉体,并通过酒精悬浮法对LiFePO_4进行修饰,修饰量为LiFePO_4质量的1%~4%,获得了薄壁蜂窝状自组装结构的LiFePO_4上修饰有球状LLTO纳米颗粒的复合正极材料。通过进行充放电测试、交流阻抗测试及循环伏安测试,研究了不同修饰量对电池的充放电比容量、循环性能及可逆性的影响,发现当LLTO含量为3%(w/w)时,以2C和5C倍率放电相对于没有修饰LLTO的LiFePO_4的比容量分别提高29.7%和31.6%,30次循环之后,容量损失率较未改性前减小4.13%,循环伏安曲线上氧化还原峰之间的电位差仅为0.117 V,以3%的LLTO修饰改性的LiFePO_4显著提高了电池的倍率性能、循环性能和低温性能。     

Electrochemical performance of LiFePO<Subscript>4</Subscript>/C doped with F synthesized by carbothermal reduction method using NH<Subscript>4</Subscript>F as dopant

The effect of fluorine doping on the electrochemical performance of LiFePO₄/C cathode material is investigated. The stoichiometric proportion of LiFe(PO₄)_1−x F_3x /C (x = 0.01, 0.05, 0.1, 0.2) materials was synthesized by a solid-state carbothermal reduction route at 650 °C using NH₄F as dopant. X-ray diffraction, scanning electron microscope, energy-dispersive X-ray, and X-ray photoelectron spectroscopy analyses demonstrate that fluorine can be incorporated into LiFePO₄/C without altering the olivine structure, but slightly changing the lattice parameters and having little effect on the particle sizes. However, heavy fluorine doping can bring in impurities. Fluorine doping in LiFePO₄/C results in good reversible capacity and rate capability. LiFe(PO₄)_0.95 F_0.15/C exhibits highest initial capacity and best rate performance. Its discharge capacities at 0.1 and 5 C rates are 156.1 and 119.1 mAh g⁻¹, respectively. LiFe(PO₄)_0.95 F_0.15/C also presents an obviously better cycle life than the other samples. We attribute the improvement of the electrochemical performance to the smaller charge transfer resistance (R _ct) and influence of fluorine on the PO₄³⁻ polyanion in LiFePO₄/C.     

Physical and electrochemical properties of La-doped LiFePO4/C composites as cathode materials for lithium-ion batteries

Olivine-type LiFePO₄ is one of the most promising cathode materials for lithium-ion batteries, but its poor conductivity and low lithium-ion diffusion limit its practical application. The electronic conductivity of LiFePO₄ can be improved by carbon coating and metal doping. A small amount of La-ion was added via ball milling by a solid-state reaction method. The samples were characterized by X-ray diffractometer (XRD), scanning electron microscopy (SEM)/mapping, differential scanning calorimetry (DSC), transmission electron microscopy (TEM)/energy dispersive X-ray spectroscopy (EDS), and total organic carbon (TOC). Their electrochemical properties were investigated by cyclic voltammetry, four-point probe conductivity measurements, and galvanostatic charge and discharge tests. The results indicate that these La-ion dopants do not affect the structure of the material but considerably improve its rate capacity performance and cyclic stability. Among the materials, the LiFe_0.99La_0.01PO₄/C composite presents the best electrochemical behavior, with a discharge capacity of 156 mAh g^?1 between 2.8 and 4.0 V at a 0.2 C-rate compared to 104 mAh g^?1 for undoped LiFePO₄. Its capacity retention is 80% after 497 cycles for LiFe_0.99La_0.01PO₄/C samples. Such a significant improvement in electrochemical performance should be partly related to the enhanced electronic conductivities (from 5.88?×?10^?6 to 2.82?×?10^?3 S cm^?1) and probably the mobility of Li⁺ ion in the doped samples. The LiFe_0.99La_0.01PO₄/C composite developed here could be used as a cathode material for lithium-ion batteries.     

Particle size effects of carbon sources on electrochemical properties of LiFePO<Subscript>4</Subscript>/C composites

Carbon-coated LiFePO₄ cathode materials were prepared by a solid-state method incorporating different sizes of polystyrene (PS) spheres as carbon sources. In scanning electron microscope images, small PS spheres appear more effective at preventing aggregation of LiFePO₄ particles. From transmission electron microscopy images, it was found that the LiFePO₄ particles were completely uniformly coated with 5-nm carbon layer when the carbon source was 0.22 μm PS spheres. When the size of PS sphere was increased to 2.75 μm, a network of carbon was formed and wrapped around the LiFePO₄ to create a conductive web. Raman spectroscopy and four-point probe conductivity measurement showed that using larger sizes of PS spheres as carbon sources leads to greater conductivity of LiFePO₄/C. The LiFePO₄ precursor sintered with 0.22 μm PS spheres delivered an initial discharge capacity of 145 mAh g^?1 at a 0.2 C rate, but it only sustained 289 cycles at 80% capacity. When the diameter of PS spheres was increased to 2.75 μm, the discharge capacity of LiFePO₄/C decreased, but the cycle life reached 755 cycles, the highest number in this work probably due to the network formation of carbon wrapping around LiFePO₄ particles.     

Synthesis of LiFePO<Subscript>4</Subscript> nanoparticles and electrochemical studies at full-cell level

LiFePO₄ nanoparticles have been successfully obtained by a solid-phase synthesis method using nanoscaled FePO₄ as starting materials. Three-electrode system using as-prepared LiFePO₄ as cathode was assembled to monitor the variation of voltage and impedance in the anode or cathode. The pouch-typed cells with prepared LiFePO₄ were assembled to investigate electrochemical performance at level of full-cell. The results show that the assembled pouch-typed full-cells present higher power density and favorable cycle life.     

A novel method with low-cost Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> to synthesize small size LiFePO<Subscript>4</Subscript> by carbothermal reduction method

The phase-pure LiFePO₄/C cathode materials have been successfully fabricated by precursor containing Fe₂O₃ coated with polyaniline through carbothermal reduction method. The polyaniline coating at Fe₂O₃ could restrict the growth of crystal and subsequently become electric carbon at higher synthesis temperature. Compared with conventional carbothermal reduction method, the sample showed a better capacity and less than 3% capacity fading after 30 cycles at various charge and discharge rate.     

Electrochemical and magnetic characterization of LiFePO<Subscript>4</Subscript> and Li<Subscript>0.95</Subscript>Mg<Subscript>0.05</Subscript>FePO<Subscript>4</Subscript> cathode materials

A series of lithium iron phosphates was synthesized via the sol–gel route. Iron phosphides, which are electronic conductors, were formed when sintered at 850°C. Magnetic susceptibility measurements on the samples show antiferromagnetic behaviour with T _N=50±2 K for LiFePO₄ and Li_0.95Mg_0.05PO₄ sintered at temperatures below 850°C. The LiFePO₄ and Li_0.95Mg_0.05FePO4 cathodes show a stable electrochemical capacity in the range of 150–160 mA h/g on cycling. The cyclability deteriorates with increasing sample sintering temperature due to the increased crystal size and impurities.     

Natural graphite enhanced the electrochemical performance of Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript> cathode material for lithium ion batteries

Natural graphite treated by mechanical activation can be directly applied to the preparation of Li₃V₂(PO₄)₃. The carbon-coated Li₃V₂(PO₄)₃ with monoclinic structure was successfully synthesized by using natural graphite as carbon source and reducing agent. The amount of activated graphite is optimized by X-ray diffraction, scanning electron microscope, transmission electron microscope, Raman spectrum, galvanostatic charge/discharge measurements, cyclic voltammetry, and electrochemical impedance spectroscopy tests. Our results show that Li₃V₂(PO₄)₃ (LVP)-10G exhibits the highest initial discharge capacity of 189 mAh g^?1 at 0.1 C and 162.9 mAh g^?1 at 1 C in the voltage range of 3.0–4.8 V. Therefore, natural graphite is a promising carbon source for LVP cathode material in lithium ion batteries.     

Impact of carbon coating thickness on the electrochemical properties of Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>/C composites

A series of Li₃V₂(PO₄)₃/C composites with different amounts of carbon are synthesized by a combustion method. The physical and electrochemical properties of the Li₃V₂(PO₄)₃/C composites are investigated by X-ray diffraction, element analysis, Raman spectroscopy, scanning electron microscopy, transmission electron microscopy and electrochemical measurements. The effects of carbon content of Li₃V₂(PO₄)₃/C composites on its electrochemical properties are conducted with cyclic voltammetry and electrochemical impedance. The experiment results clearly show that the optimal carbon content is 4.3 wt %, and more or less amount of carbon would be unfavorable to electrochemical properties of the Li₃V₂(PO₄)₃/C electrode materials. The results would provide some basis for further improvement on the Li₃V₂(PO₄)₃ electrode materials.     

High loading LiFePO<Subscript>4</Subscript> on activated carbon fiber cloth as a high capacity cathode for Li-ion battery

The LiFePO₄/carbon fiber (LFP/CF) cathodes were prepared by using activated carbon fiber cloth as current collector in place of conventional Al foil. The electrochemical properties of LFP/CF electrodes were analyzed by the cyclic voltammetry and galvanostatic charge/discharge tests. The results indicate that the activated carbon fiber cloth with high specific surface area and high porosity makes the LFP/CF electrode that possesses higher mass loading of 18–21 mg cm^–2 and stronger redox reaction ability compared with Al foil-based electrode. The LFP/CF electrode shows excellent rate performance and cycle stability. At 0.1C, the discharge capacity is up to 190.1 mAh g^–1 that exceeds the theoretical capacity due to the combination effect of battery and capacitor. Furthermore, the LFP/CF electrode shows an initial capacity of 150.4 mAh g^–1 at 1C with a capacity retention of 74.7% after 425 cycles, which is higher than 62.4% for LFP/Al foil electrode, and an initial discharge capacity of 130 mAh g^–1 at 5C with a capacity retention of 61.5% after 370 cycles. But this composite electrode is not suitable for charging/discharging at higher rate as 10C due to too much mass loading.