末端可裁切碳纳米管薄膜电极的制备及其双酚A电化学检测应用

通过真空抽滤方法得到均匀致密的高导电多壁碳纳米管(MWCNTs)薄膜,利用聚二甲基硅氧烷(PDMS)对其进行封闭处理,制备出末端可裁切的PDMS基柔性碳纳米管薄膜电极,其裁切端面为电化学传感界面。在十六烷基三甲基溴化铵(CTAB)的增敏作用下,所制备的电化学传感器对双酚A(BPA)具有灵敏的电化学响应,其峰电流与BPA浓度在0.05~0.5μmol/L和0.5~12μmol/L范围内呈良好的线性关系,检测限为50nmol/L。通过电极末端的重复裁切可避免电极污染,并实现电极表面的快速更新和重复使用。对同一支电极进行13次连续裁切,用于10μmol/L BPA的检测,其相对标准偏差为3.4%。将该传感器应用于热敏纸样品中BPA的检测,加标回收率在95%~105%之间。     

二氧化硅/金复合膜修饰玻碳电极用于双酚A的检测

该文制备了二氧化硅/金复合膜修饰玻碳电极(SiO_2/Au/GCE),提出了一种简便检测双酚A(BPA)的电化学分析方法。采用扫描电镜(SEM)和红外光谱(FT-IR)对SiO_2和SiO_2/Au的形貌和结构进行了表征,循环伏安法(CV)和交流阻抗法(EIS)研究了SiO_2/Au/GCE的表面电化学特性,同时用CV、计时库仑法(CC)、控制电位电解库仑法、线性扫描伏安法(LSV)和差分脉冲伏安法(DPV)等研究了BPA在SiO_2/Au/GCE上的电化学行为,优化了实验参数,并得到电化学动力参数。实验发现:SiO_2/Au/GCE对BPA具有良好的电催化活性,BPA在该修饰电极上的氧化峰电流为GCE上的3倍,且BPA在SiO_2/Au/GCE上的氧化过程为2电子2质子的完全不可逆电极过程。在最佳条件下,BPA的氧化峰电流分别在0.01~0.50μmol/L和0.50~25μmol/L浓度范围内呈良好的线性关系,检出限为1.9×10-8mol/L。用于一次性手套中BPA含量的测定,回收率为98.9%~105.3%,与高效液相色谱法(HPLC)进行对照,结果满意。     

电化学沉积纳米金和石墨烯修饰离子液体碳糊电极检测芦丁的研究

以六氟磷酸正己基吡啶为粘合剂和修饰剂,制备了离子液体修饰碳糊电极(CILE)。用电化学方法依次将纳米金和石墨烯(GR)电沉积在CILE表面制备了相应的修饰电极(GR/Au/CILE)。电极表面纳米金和GR的存在极大地提高了电极的电化学性能。进一步用循环伏安法、示差脉冲伏安法和计时库仑法等电化学方法研究了芦丁在GR/Au/CILE上的电化学行为,求解了相关的电化学参数。在最佳实验条件下,芦丁的氧化峰电流与其浓度在8.0×10"8～8.0×10"5mol/L范围内呈现良好的线性关系,检出限为2.55×10"8mol/L(3σ)。将本方法应用于复方芦丁片样品的测定,结果令人满意。     

聚中性红纳米金功能化石墨烯修饰电极的制备及其对多巴胺的电化学检测

以离子液体1-乙基-3-甲基咪唑四氟硼酸盐为粘合剂制备了离子液体修饰碳糊电极(CILE)。采用循环伏安沉积法一步制备了聚中性红-纳米金功能化石墨烯复合材料修饰CILE (p NR-nAu-GR/CILE),并用循环伏安法、交流阻抗法、电子扫描电镜法对电极进行了表征,表明pNR-nAu-GR/CILE具有良好的导电能力。研究了多巴胺(DA)在pNR-nAu-GR/CILE上的电化学行为,考察了扫描速度、溶液pH等参数对DA检测的影响,计算了相关的电化学参数,电子转移数为1.7,电子传递系数为0.60,表观异相电子转移速率常数为1.65 s~(-1)。考察了常见干扰物质对DA的检测影响,结果良好。在最优实验条件下,采用示差脉冲法获得了DA在0.05～800.0μmol/L范围内的工作曲线,检测限为12 nmol/L。将pNRn Au-GR/CILE进一步用于人尿的检测,样品回收率为96.3%～105.9%,相对标准偏差小于4.3%。     

Hb/Fe3O4/CILE修饰电极的制备及应用

以类离子液体碳糊电极(CILE)为基体电极,采用滴涂法和利用静电吸附作用,制备了Hb/Fe3O4/CILE修饰电极,研究了Hb的直接电化学及其电催化行为,建立了H2O2的计时安培测定新方法。结果表明:Hb在该修饰电极上,Hb呈现了一对准可逆的氧化还原峰,且其在该修饰电极表面表观覆盖度为2.65×10-9moL/cm2;电子转移速率常数为1.35/s;表观米氏常数为1.59×10-5mol/L。在1.0×10-6~4.0×10-5mol/L范围内,催化电流与H2O2浓度呈线性关系(r=0.9976),检出限为3.0×10-7mol/L(S/N=3)。     

三磷酸腺苷在TiO2掺杂碳纳米纤维修饰电极上的电化学行为

采用循环伏安法和示差脉冲伏安法研究了三磷酸腺苷(ATP)在TiO2掺杂碳纳米纤维(TiO2@CNF)修饰的碳离子液体电极表面(TiO2@CNF/CILE)的电化学行为。结果表明,ATP在TiO2@CNF/CILE表面有一个明显的氧化峰,在pH 3.0的Britton-Robinson(BR)缓冲溶液中修饰电极对ATP具有显著的电催化作用。纤维状的TiO2@CNF能够有效促进电子转移,增加电化学信号。当ATP浓度分别在4.0×10^-9~2.0×10^-6mol/L和2.0×10^-6~1.0×10^-4mol/L范围时,氧化峰电流与ATP浓度呈良好的线性关系,检测限为1.4 nmol/L。修饰电极可用于注射液中ATP的测定。     

PB/Au/CILE的制备与应用

混合离子液体(N-丁基吡啶六氟磷酸盐,[BuPy][PF6])与石墨粉,制备了离子液体碳糊电极(CILE),再采用电沉积法制得PB/Au/CILE修饰电极,研究了该修饰电极的电化学行为及其对H2O2的电催化,建立了H2O2的计时安培测定新方法。结果表明:在该修饰电极上PB产生了一对准可逆的氧化还原峰,并对H2O2表现出良好电催化作用,安培法测定H2O2的线性范围为5.0×10-6～1.55×10-4mol/L,检出限为1.0×10-6mol/L(S/N=3)。连续10次测定5.0×10-6mol/L H2O2峰电流的RSD为2.1%。     

双酚A在SDS现场自组装膜与[bupy]PF6复合修饰碳糊电极上的电催化氧化及电分析方法

研究了双酚A(BPA)在十二烷基硫酸钠(SDS)现场自组装膜与离子液体N-丁基吡啶夫氟磷酸盐([ bupy]PF6)复合修饰碳糊电极(SDS-[ bupy]PF6/CPE)上的电催化氧化行为和电化学动力学性质.实验结果表明,在SDS-[ bupy]PF6/CPE上BPA发生了一受扩散控制的不可逆电化学氧化过程,用循环伏安(CV)法和计时电流(CA)法测得BPA在SDS-[bupy]PF6/CPE上的电极反应过程动力学参数.用方波伏安(SWV)法测得BPA氧化峰电流(Ipa)与其浓度在1.0×10-5～ 1.0×10-3 mol/L范围内呈良好的线性关系,线性方程为Ipa(μA) =2.635 +51.30c( 10-3 mol/L),r =0.998 1,检测限(S/N=3)为3.01×10-7 mol/L,同时运用SWV法对湖水样品中双酚A的含量进行了电化学定量测定.     

石墨烯修饰电化学适配体传感器测定双酚A

构建了一种检测双酚A(BPA)的电化学适配体传感器。利用在线电化学方法将氧化石墨烯还原为石墨烯,通过石墨烯与单链DNA之间的相互作用,将BPA适配体单链DNA吸附固定在修饰电极上,制备了BPA电化学适配体传感器。以铁氰化钾-亚铁氰化钾平衡电对为电化学探针,利用电化学循环伏安法和差分脉冲伏安法对BPA传感器的性能进行了研究。结果表明,在最优化实验条件下,传感器对BPA的检测线性范围在1.0×10~(-15)~1.0×10~(-10)mol/L之间,检出限为3.3×10~(-16)mol/L(S/N=3)。     

植酸镁基修饰电极的制备及其对双酚A的检测

采用水热法制备了植酸基材料（PAC）和植酸镁基复合材料（PA-Mg）,并用扫描电镜（SEM）, X射线衍射（XRD）, X射线光电子能谱（XPS）对PAC和PA-Mg进行了表征。分别采用循环伏安法（CV）和交流阻抗法（EIS）探究了2种材料的电化学性能,采用微分脉冲伏安法（DPV）探究了2种材料对双酚A(BPA)的响应。结果表明,相比PAC, PA-Mg表现出更优异的电化学性能,分别以PA-Mg和PAC为修饰材料,以玻碳电极（GCE）为基底电极构建PA-Mg/GCE和PAC/GCE。PA-Mg/GCE对BPA的响应电流值是PAC/GCE的2.2倍。PA-Mg/GCE在最佳检测条件下对BPA的线性响应范围为0.8～50μmol/L,检出限为0.1μmol/L,相关系数为0.996。将PA-Mg/GCE用于模拟废水中BPA浓度的测定,加标回收率在92.5%～101.5%之间。     

氧化石墨烯修饰碳离子液体电极同时测定鸟嘌呤和腺嘌呤

以离子液体1-丁基-3-甲基咪唑六氟磷酸盐为粘合剂制备了碳糊电极,然后将氧化石墨烯滴涂到碳糊电极表面制成了一种新型的氧化石墨烯修饰碳离子液体电极。研究了鸟嘌呤和腺嘌呤在修饰电极上的电化学行为。实验结果表明,在0.1 mol/L醋酸盐缓冲溶液中(pH4.5),鸟嘌呤和腺嘌呤在该修饰电极上具有良好的电化学行为,在2.0×10-7～1.5×10-5mol/L浓度范围内鸟嘌呤和腺嘌呤的浓度在该电极上与电化学响应信号呈良好的线性关系,相关系数分别为为0.992和0.996。信噪比为3时,检出限为1.0×10-8mol/L。     

Sensitive and Simple Electrochemical Detection of Lead(II) with Carbon Ionic Liquid Electrode

In this paper a carbon ionic liquid electrode (CILE) was fabricated by using ionic liquid 1‐ethyl‐3‐methylimidazolium ethylsulphate ([EMIM]EtOSO₃) as the modifier and further used as the working electrode for the sensitive anodic stripping voltammetric detection of Pb²⁺. The characteristics of the CILE were investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). In pH 4.5 NaAc‐HAc buffer Pb²⁺ was accumulated on the surface of CILE due to the extraction effect of IL and reduced at a negative potential (‐1.20 V). Then the reduced Pb was oxidized by differential pulse anodic stripping voltammetry with an obvious stripping peak appeared at ?0.67 V. Under the optimal conditions Pb²⁺ could be detected in the concentration range from 1.0 × 10^?8 mol/L to 1.0 × 10^?6 mol/L with the linear regression equation as I_p(μA) = ?0.103 C (μmol/L) + 0.0376 (γ = 0.999) and the detection limit as 3.0 × l0^?9 mol/L (3σ). Interferences from other metal ions were investigated and Cd²⁺ could be simultaneously detected in the mixture solution. The proposed method was further applied to the trace levels of Pb²⁺ detection in water samples with satisfactory results.     

Electrochemistry and Voltammetric Determination of Adenosine with N‐Hexylpyridinium Hexafluorophosphate Modified Electrode

An ionic liquid N‐hexylpyridinium hexafluorophosphate (HPPF₆) modified carbon paste electrode was fabricated for the sensitive voltammetric determination of adenosine in this paper. Carbon ionic liquid electrode (CILE) was prepared by mixing graphite powder and HPPF₆ together and the CILE was characterized by scanning electron microscopy (SEM) and electrochemical methods. The electrochemical behaviors of adenosine on the CILE were studied carefully. Compared with the traditional carbon paste electrode (CPE), a small negative shift of the oxidation peak potential appeared with greatly increase of the oxidation peak current, which indicated the presence of ionic liquid in the carbon paste not only as the binder but also as the modifier and promoter. Under the optimal conditions the oxidation peak current increased with the adenosine concentration in the range from 1.0×10^?6 mol/L to 1.4×10^?4 mol/L with the detection limit of 9.1×10^?7 mol/L (S/N=3) by differential pulse voltammetry. The proposed method was applied to the human urine samples detection with satisfactory results.     

A sensitive electrochemical sensor for detection of rutin based on a gold nanocage‐modified electrode

In this article, an electrochemical sensor based on a gold nanocage (AuNC)‐modified carbon ionic liquid electrode (CILE) was fabricated and applied to the sensitive rutin determination. The presence of AuNCs on the electrode surface greatly improved the electrochemical performance of the working electrode due to its specific microstructure and high metal conductivity. Electrochemical behavior of rutin on AuNCs/CILE was studied using cyclic voltammetry and differential pulse voltammetry with the related electrochemical parameters calculated. Under the optimal experimental conditions, the oxidation peak current of rutin and its concentration had good linear relationship in the range from 4.0 × 10^?9 to 7.0 × 10^?4 mol/L with a low detection limit of 1.33 × 10^?9 mol/L (3σ). This fabricated AuNCs/CILE was applied to direct detection of the rutin concentration in drug samples with satisfactory results, showing the real application of AuNCs in the field of chemically modified electrodes.     

Direct electrocatalvtic reduction of p-nitrophenol at room temperature ionic 1iquid modified electrode

Direct electrochemical reduction of p-nitrophenol(PNP)was investigated on a room temperature ionic liquid N-butylpyridinium hexafluorophosphate(BPPF6)modified carbon paste electrode(CILE).The cathodic peak potential was positively shifted and the peak currents were increased compared to that obtained on traditional carbon paste electrode(CPE).The results indicated that the presence of ionic liquid BPPF6 on the electrode surface showed excellent catalytic ability to the electrochemical reduction of PNP.The electrochemical behaviors of PNP on the CILE were investigated by cyclic voltammetry and the conditions such as the scan rate,the buffer pH,the substrate concentration were optimized.The electrochemical parameters were further calculated with the results of the electron transfer number(n),the charge-transfer coefficient(α)and the surface concentration(ΓΥ)as 1.76,0.37 and 2.47×10-9 mol/cm2,respectively,for the selected reducfive peak.The results indicated that PNP showed all irreversible adsorption-controlled electrode process on the CILE.     

Direct electrocatalytic reduction of p-nitrophenol at room temperature ionic liquid modified electrode

Direct electrochemical reduction ofp-nitrophenol （PNP） was investigated on a room temperature ionic liquid N-butylpyridinium hexafluorophosphate （BPPF6） modified carbon paste electrode （CILE）. The cathodic peak potential was positively shifted and the peak currents were increased compared to that obtained on traditional carbon paste electrode （CPE）. The results indicated that the presence of ionic liquid BPPF6 on the electrode surface showed excellent catalytic ability to the electrochemical reduction of PNP. The electrochemical behaviors of PNP on the CILE were investigated by cyclic voltammetry and the conditions such as the scan rate, the buffer pH, the substrate concentration were optimized. The electrochemical parameters were further calculated with the results of the electron transfer number （n）, the charge-transfer coefficient （α） and the surface concentration （Гr） as 1.76, 0.37 and 2.47 × 10^-9 mol/cm^2, respectively, for the selected reductive peak. The results indicated that PNP showed an irreversible adsorption-controlled electrode process on the CILE.     

Electrochemical aptamer sensor for highly sensitive detection of mercury ion with Au/Pt@carbon nanofiber‐modified electrode

In this paper, an electrochemical aptamer sensor was proposed for the highly sensitive detection of mercury ion (Hg²⁺). Carbon nanofiber (CNF) was prepared by electrospinning and high‐temperature carbonization, which was used for the loading of platinum nanoparticles (PtNPs) by the hydrothermal method. The Pt@CNF nanocomposite was modified on the surface of carbon ionic liquid electrode (CILE) to obtain Pt@CNF/CILE, which was further decorated by gold nanoparticles (AuNPs) through electrodeposition to get Au/Pt@CNF/CILE. Self‐assembling of the thiol‐based aptamer was further realized by the formation of Au‐S bond to get an electrochemical aptamer sensor (Aptamer/Au/Pt@CNF/CILE). Due to the specific binding of aptamer probe to Hg²⁺ with the formation of T‐Hg²⁺‐T structure, a highly sensitive quantitative detection of Hg²⁺ could be achieved by recording the changes of current signal after reacting with Hg²⁺ within the concentration range from 1.0 × 10^?15 mol/L to 1.0 × 10^?6 mol/L and the detection limit of 3.33 × 10^?16 mol/L (3σ). Real water samples were successfully analyzed by this method.