Preparation and characterization of Ni(II)/polyacrylonitrile and carbon nanotube composite modified electrode and application for carbohydrates electrocatalytic oxidation

A nickel(II) into porous polyacrylonitrile–carbon nanotubes composite modified glassy carbon electrode (Ni/PAN-CNT/GCE) was fabricated by simple drop-casting and immersing technique. The unique electrochemical activity of Ni/PAN-CNT composite modified glassy carbon electrode was illustrated in 0.10?M NaOH using cyclic voltammetry. The Ni/PAN-CNT/GCE exhibits the characteristic of improved reversibility and enhanced current responses of the Ni(III)/Ni(II) couple compared with Ni/PAN/GCE and Ni/CNT/GCE. The results of electrochemical impedance spectroscopy and scanning electron microscopy indicated the successful immobilization for PAN-CNT composite film. Kinetic parameters such as the electron transfer coefficient, α, and rate constant, k _s, of the electrode reaction were determined. Ni/PAN-CNT/GCE also shows good electrocatalytic activity toward the oxidation of carbohydrates (glucose, sucrose, fructose, and sorbitol). The electrocatalytic response showed a wide linear range (10–1,500, 12–3,200, 7–3,500, and 16–4,200?μM for glucose, sucrose, fructose, and sorbitol, respectively) as well as its experimental limit of detection can be achieved 6, 7, 5, and 11?μM for glucose, sucrose, fructose, and sorbitol, respectively. The modified electrode for carbohydrates determination is of the property of simple preparation, good stability, and high sensitivity.     

Direct electrochemistry of glucose oxidase immobilized on TiO2–graphene/nickel oxide nanocomposite film and its application

A novel electrochemical platform based on nickel oxide (NiO) nanoparticles and TiO₂–graphene (TiO₂–Gr) was developed for the direct electrochemistry of glucose oxidase (GOD). The electrochemical behavior of the sensor was studied using cyclic voltammetry and chronoamperometry. The experimental results demonstrated that the nanocomposite well retained the activity of GOD and the modified electrode GOD/NiO/TiO₂–Gr/GCE exhibited excellent electrocatalytic activity toward the redox of GOD as evidenced by the significant enhancement of redox peak currents in comparison with bare GCE. The biosensor responded linearly to glucose in the range of 1.0–12.0?mM, with a sensitivity of 4.129?μA?mM^?1 and a detection limit of 1.2?×?10^?6?M under optimized conditions. The response time of the biosensor was 3?s. In addition, the developed biosensor possessed good reproducibility and stability, and there was negligible interference from other electroactive components.     

NiO/MnO_2分级纳米片阵列复合材料的制备与超电容性能

通过化学浴沉积和水热法在泡沫镍上制备了NiO/MnO_2分级纳米片阵列复合材料,XRD和SEM测试表明NiO纳米片垂直生长在泡沫镍上,交叉形成网状阵列结构;MnO_2纳米介孔泡沫进一步生长在NiO纳米片两侧,与NiO形成了壳核式的复合结构。循环伏安和恒流充放电测试发现,NiO/MnO_2分级纳米片阵列复合材料的电化学性能相比复合前得到明显改善,在1 A·g~(-1)的电流密度下,比电容提高至1 297 F·g~(-1);2 A·g~(-1)下循环1 000次,比电容保持率高达97%,比电容和循环性能的改善是由于分级纳米片阵列复合结构方便了电解液传质,扩大了活性材料与电解液的接触,促进了赝电容反应,提高了NiO和MnO_2的结构稳定性。     

NiO/MnO2分级纳米片阵列复合材料的制备与超电容性能

通过化学浴沉积和水热法在泡沫镍上制备了NiO/MnO₂分级纳米片阵列复合材料,XRD和SEM测试表明NiO纳米片垂直生长在泡沫镍上,交叉形成网状阵列结构;MnO₂纳米介孔泡沫进一步生长在NiO纳米片两侧,与NiO形成了壳核式的复合结构。循环伏安和恒流充放电测试发现,NiO/MnO₂分级纳米片阵列复合材料的电化学性能相比复合前得到明显改善,在1 A·g^-1的电流密度下,比电容提高至1 297 F·g^-1;2 A·g^-1下循环1 000次,比电容保持率高达97%,比电容和循环性能的改善是由于分级纳米片阵列复合结构方便了电解液传质,扩大了活性材料与电解液的接触,促进了赝电容反应,提高了NiO和MnO₂的结构稳定性。     

Synthesis and Enhanced Photocatalytic Activity of a Hierarchical Porous Flowerlike p–n Junction NiO/TiO2 Photocatalyst

Hierarchical flowerlike β‐Ni(OH)₂ superstructures composed of intermeshed nanoflakes are synthesized by hydrothermal treatment with a mixed solution of C₂H₄(NH₂)₂, NaOH, and Ni(NO₃)₂. The as‐prepared β‐Ni(OH)₂ superstructures could be easily changed into NiO superstructures without great morphology change by calcination at 400 °C for 5 h. Furthermore, the TiO₂ nanoparticles can be homogeneously deposited on the surface of NiO superstructures by dispersing β‐Ni(OH)₂ powders in Ti(OC₄H₉)₄–C₂H₅OH mixed solution and then vaporizing to remove the ethanol at 100 °C, and finally calcination at 400 °C for 5 h. The prepared NiO/TiO₂ p–n junction superstructures show much higher photocatalytic activity for photocatalytic degradation of p‐chlorophenol aqueous solution than conventional TiO₂ powders and NiO superstructures prepared under the same experimental conditions. An obvious enhancement in the photocatalytic activity can be related to several factors, including formation of hierarchical porous structures, dispersion of TiO₂ particles on the surface of NiO superstructures, and production of a p–n junction. Further results show that NiO/TiO₂ composite superstructures can be more readily separated from the slurry system by filtration or sedimentation after photocatalytic reaction and re‐used, compared with conventional powder photocatalysts. After many recycling experiments for the photodegradation of p‐chlorophenol, the NiO/TiO₂ composite sample does not exhibit any great activity loss, confirming that NiO/TiO₂ sample is stable and not photocorroded.     

Fabrication of Ni Nanoclusters-Modified Brookite TiO2 Quasi Nanocubes and Its Photocatalytic Hydrogen Evolution Performance

The development of low-cost, earth-abundant and highly-efficient cocatalysts is still important to promote the photocatalytic H₂ evolution reaction over semiconductors. Herein, a series of Ni nanoclusters (NCs) modified brookite TiO₂ quasi nanocubes (BTN) (marked as Ni/BTN) are fabricated via a chemical reduction process. It is found that the loading content and oxidation state of Ni NCs can significantly influence the optical absorption, photocat-alytic activity, and stability of Ni/BTN composites. Among the resultant Ni NCs-loaded products, 0.1%Ni/BTN composite delivers the best H₂ evolution activity (156 μmol/h), which is 4.3 times higher than that of the BTN alone (36 μmol/h). Furthermore, the Ni NCs with ultra ne size (∽2 nm) and high dispersity enable shorter charge transfer distance by quickly capturing the photoexcited electrons of BTN, and thus result in the improved activity even though the oxidization of some Ni NCs on BTN is harmful to the activity for H₂ evolution due to the much lower electron capturing capability of NiO than metallic Ni. This study not only clari es that brookite TiO₂ would be a promising high-efficient photo-catalyst for H₂ evolution, but also reveals vital clues for further improving its photocatalytic performance using low-cost Ni-based cocatalyst.     

Ni/NiCo2O4电极的制备及其析氧反应性能

采用溶胶-凝胶法制备NiCo₂O₄尖晶石粉体, 然后以多孔Ni 为基体, 通过复合溶胶涂覆结合烧结制备Ni/NiCo₂O₄ 涂层电极. 运用扫描电子显微镜(SEM)、能量色散谱(EDS)和X 射线衍射(XRD)表征粉体以及Ni/NiCo₂O₄涂层电极的组成和结构. 采用循环伏安(CV), 稳态极化(LSV), 电化学阻抗谱(EIS), 恒电位阶跃以及恒电位长时间电解研究涂层电极在5 mol·L^-1 KOH溶液中的电催化析氧反应(OER). 结果表明: Ni/NiCo₂O₄涂层电极与多孔Ni 电极对比, 具有低的析氧过电位、高的比表面积和高的稳定性能; 其中比表面积增大了28.69倍,表观活化能在不同过电位分别降低了166.78和162.15 kJ·mol^-1.     

Effect of atomic-layer-deposited TiO2 on carbon-supported Ni catalysts for electrocatalytic glycerol oxidation in alkaline media

Thin TiO₂ layers were deposited onto a carbon-supported Ni catalyst (Ni/C) through atomic layer deposition (ALD) and the resulting TiO₂-coated Ni/C (ALD(TiO₂)-Ni/C) was utilized for electrochemical glycerol oxidation in alkaline media. X-ray photoelectron spectroscopy analysis demonstrated that the Ni surface phase of ALD(TiO₂)-Ni/C mainly consisted of Ni(OH)₂ while that of uncoated Ni/C was a mixed phase of NiO and Ni(OH)₂. The ALD(TiO₂)-Ni/C exhibited electrocatalytic activity at least 2.4 times higher than that of Ni/C. Density functional theory calculations were used to investigate how the modified Ni surface with the TiO₂ coating affects the adsorption/desorption of glycerol.     

Construction of hierarchical nanostructures and NiO nanosheets@nanorods for efficient urea electrooxidation

Hierarchical NiO nanosheets@nanorods have been rationally designed and constructed for efficient urea electrooxidation in an alkaline solution. The critical synthetic strategy, engaging the one-step anion-competitive reaction, precisely integrates two nickel-based materials into a heterostructure with Ni(OH)₂ nanosheets and NiC₂O₄ nanorods. Benefiting from the hierarchically porous structure and high specific surface area, the NiO NNs can improve the escape efficiency of gas in electrochemical reactions and maintain sustainability. Furthermore, this distinctive structure can expose highly dispersed active sites for enhancing urea molecules' adsorption, surface-dependent redox reactions, and electrical conductivities. As a result, these hierarchical NiO nanosheets@nanorods exhibit superior activity with a low overpotential of 156 mV at 10 mA/cm², and a slight Tafel slope of 40.7 mV/dec, and high stability with almost no decay of 12,000 s for urea electrooxidation. This work promotes the application of well-designed hierarchical structure in electrooxidizing urea and provides a possibility for highly efficient electrolysis of alkaline urea wastewater.     

NiO/ZnO Composite Derived Metal-Organic Framework as Advanced Electrode Materials for Zinc Hybrid Redox Flow Battery

NiO/ZnO composite derived metal-organic framework (MOF) is used as to modify carbon felt (CF) via a conventional solid-state reaction followed by ultrasonication. The prepared electrode material is used in zinc-hybrid redox flow batteries (RFBs) due to their high redox activity of Zn²⁺/Zn. The electrochemical performance of composite modified CF and pre-treated CF was studied by cyclic voltammetry (CV) in 0.5 M aqueous zinc chloride with 5 M potassium hydroxide solutions showed clear confirmation for enhanced electrocatalytic activity. The unique porous structure of NiO/ZnO-derived MOF with increased surface area improves the battery behavior significantlyThe peak current ratio for the as-prepared material is about 3 times higher than that of the pre-treated CF due to more active sites. Zinc-based RFB with modified CF electrode exhibited better electrochemical performance with voltage efficiency (VE, 88 %), which is higher than true redox flow batteries.     

Preparation of nickel oxide and carbon nanosheet array and its application in glucose sensing

Nickel oxide and carbon (NiO/C) nanosheet array was fabricated on Ti foil for the first time by calcining the precursor, which was synthesized through the hydrothermal reaction of nickel acetate, urea and glucose. The slow release of OH⁻ by the hydrolysis of urea aided in the direct nucleation and adhesion of precursor seeds on Ti substrate. The presence of carbon ensured a large specific surface area and good conductivity of the final NiO/C composite. The prepared NiO/C nanosheet array exhibited higher catalytic oxidation activity of glucose compared with the pure NiO nanosheet at a detection limit of 2 μM, linear range up to 2.6 mM (R²=0.99961), and sensitivity of 582.6 μAm M⁻¹ cm⁻². With good analytical performance, simple preparation and low cost, this composite is promising for nonenzymatic glucose sensing.     

Fabrication,characterization of polyaniline intercalated NiO nanocomposites and application in the development of non-enzymatic glucose biosensor

Determination of glucose plays very important part in diagnostics and management of diabetes. Nowadays, determination of glucose is necessary in human health. In order to develop the glucose biosensor, polymer modified catalytic composites were fabricated and used to detect glucose molecules. In this work, NiO nanostructure metal oxide (NMO) was fabricated via thermal decomposition method and polyaniline (wt% = 2, 4 and 6) assisted nanocomposites (NiO/PANI) were also prepared. The morphology and structure of synthesized nanocomposites were characterized by UV–visible diffusion reflectance spectroscopy (UV–vis-DRS), Fourier transform- infra red spectroscopy (FT-IR), X-ray powder diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), high resolution transmission electron microscopy (HR-TEM), X-ray photoelectron spectroscopy (XPS) and N₂ adsorption-desorption isotherm measurement. The modified NiO/6%PANI/GCE had higher catalytic activity toward the oxidation of glucose than NiO/GCE, PANI/GCE, NiO/2%PANI/GCE and NiO/4%PANI/GCE. This is due to the larger surface area of NiO/6%PANI nanocomposites provide a ploform for faster electron transfer to the detection of glucose. The constructed glucose biosensor have been exhibited a high sensitivity of 606.13 µA mM⁻¹ cm⁻², lowest detection limit of 0.19 µM, high selectivity, stability, simplicity and low cost for the quick detection of glucose in real sample as well.     

Amperometric nonenzymatic determination of glucose via a glassy carbon electrode modified with nickel hydroxide and N-doped reduced graphene oxide

The authors describe a nonenzymatic glucose sensor that was obtained by electrochemical deposition and oxidization of metallic nickel on the surface of nitrogen-doped reduced graphene oxide (N-RGO) placed on a glassy carbon electrode (GCE). An analysis of the morphology and chemical structure indicated the composite to possess a well-defined vermicular Ni(OH)₂ nanorods combined with N-RGO. The electrochemical performance of the modified GCE with respect to the detection of glucose in 0.1 M NaOH was investigated by cyclic voltammetry and amperometry. The wrinkle and protuberance of N-RGO for loading of nanostructured Ni(OH)₂ are found to increase electrical conductivity, surface area, electrocatalytical activity and stability. The modified GCE displays a high electrocatalytic activity towards the oxidation of glucose in 0.1 M NaOH solution. The lower detection limit is 0.12 μM at an applied potential of +0.45 V (vs Ag/AgCl) (S/N=3), and the sensitivity is 3214 μA mM^?1 cm^?2. The modified GCE possesses long-term stability, good reproducibility and high selectivity over fructose, sucrose and lactose.

Open image in new window

Graphical abstract The composite of vermicular Ni(OH)₂ nanorods combined with N-doped reduced graphene oxide is a viable catalyst for non-enzymatic electrochemical sensing of glucose.

     

A highly sensitive nonenzymatic glucose sensor based on nickel oxide–carbon nanotube hybrid nanobelts

In this study, we demonstrated a highly sensitive electrochemical sensor for the determination of glucose in alkaline aqueous solution by using nickel oxide single-walled carbon nanotube hybrid nanobelts (NiO–SWCNTs) modified glassy carbon electrode (GCE). The hybrid nanobelts were prepared by the deposition of SWCNTs onto the Ni(SO₄)_0.3(OH)_1.4 nanobelt surface, followed by heat treatment at different temperatures ranging from 400 °C to 600 °C. The NiO–SWCNTs hybrid nanobelts modified electrode prepared at 500 °C displays enhanced electrocatalytic activity towards glucose oxidation, revealing a synergistic effect between the NiO and the deposited SWCNTs. The as-fabricated nonenzymatic glucose sensor exhibits excellent glucose sensitivity (2,980 μA cm^?2 mM^?1), lower detection limit (0.056 μM, signal/noise [S/N] ratio?=?3), and wider linear range (0.5–1,300 μM). Moreover, the sensor has been successfully used for the assay of glucose in serum samples with good recovery, ranging from 96.4 % to 102.4 %.     

Electroanalytical Detection of n‐Butylamine at a Nickel/Carbon Nanotube Composite

We report the electroanalytical detection of n‐butylamine at a nickel/carbon nanotube (Ni/CNT) composite. Scanning Electron Microscopy (SEM) characterisation of the composite demonstrated that it consisted of bulk nickel particles ca. 2 μm in diameter entangled in CNT bundles. The spontaneous formation of Ni(OH)₂ was optimised, and comparison with a 3 mm nickel electrode showed that ca. 4 μg of the Ni/CNT composite cast on a 3 mm GC electrode possessed bulk nickel characteristics while also having higher activity and higher sensitivity towards the electrochemical detection of n‐butylamine. However, the Ni/CNT composite showed no response to ammonia, in contrast to the macro‐nickel‐electrode.     

Sensitivity Enhancement in Nickel Hydroxide/3D‐Graphene as Enzymeless Glucose Detection

A nickel hydroxide (Ni(OH)₂)/3D‐graphene composite is used as monolithic free‐standing electrode for enzymeless electrochemical detection of glucose. Ni(OH)₂ nanoflakes are synthesized by using a simple solution growth procedure on 3D‐graphene foam which was grown by chemical vapor deposition (CVD). The pore structure of 3D‐graphene allows easy access to glucose with high surface area, which leads to glucose detection with an ultrahigh sensitivity of 3.49 mA mM^?1 cm^?2 and a significant lower detection limit up to 24 nM. Cyclic voltammetry (CV) and potentionstatic mode is used for non‐enzymatic glucose sensing. The impedance and effective surface area have been studied well. The high sensitivity, low detection limit and simple configuration of Ni(OH)₂/three dimensional (3D)‐graphene composite electrodes can evoke its industrial application in glucose sensing devices.     

Fabrication of a Hierarchical Ni(OH)2@Ni3S2/Ni Foam Electrode from a Prussian Blue Analogue-Based Composite with Enhanced Electrochemical Capacitive and Electrocatalytic Properties

Developing high-efficiency, cost-effective, and durable electrodes is significant for electrochemical capacitors and electrocatalysis. Herein, a 3D bifunctional electrode consisting of nickel hydroxide nanosheets@nickel sulfide nanocubes arrays on Ni foam (Ni(OH)₂@Ni₃S₂/NF) obtained from a Prussian blue analogue-based precursor is reported. The 3D higher-order porous structure and synergistic effect of different compositions endow the electrode with large specific surface area, facile ion/electron transport path, and improved conductivity. As a result, the Ni(OH)₂@Ni₃S₂/NF electrode exhibits a high specific capacity of 211 mA h g⁻¹ at a current density of 1 A g⁻¹ and 73 % capacity retention after 5000 cycles at 5 A g⁻¹. Moreover, the Ni(OH)₂@Ni₃S₂/NF electrode has superior electrocatalytic activity for the hydrogen evolution reaction with low overpotentials of 140 and 210 mV at current densities of 10 and 100 mA cm⁻², respectively. The synthetic strategy for the unique higher-order porous structure can be extended to fabricate other composite materials for energy storage and conversion.     

Ni/PdO/RuO_2复合型活性阴极的制备与表征

采用热分解氧化法,在Ni基体上制备以PdO为中间层、RuO2为活性层的Ni/PdO/RuO2复合型活性阴极,并通过XPS、XRD、能量色散X荧光(EDXRF)、SEM、极化曲线、循环伏安法和交流阻抗谱等表征其组成、结构与电化学性能。结果表明,Pd和Ru分别以PdO和RuO2的形式存在于Ni/PdO/RuO2复合型活性阴极中,其含量分别为1.25wt%和1.71wt%;在363K、11mol·L-1NaOH溶液、3kA·m-2电流密度下,Ni/PdO/RuO2复合型活性阴极的析氢过电位比Ni电极和Ni/RuO2电极分别低371和125mV;循环伏安法循环72h后,该复合型活性阴极双电层电容值减小30.6%,比Ni/RuO2电极表层结构更稳定;Ni/PdO/RuO2复合型活性阴极的表面粗糙度大且无明显的裂纹存在,与纯镍电极相比,该复合型活性阴极比表面积增加了31.12倍。     

Comparison of Insulin Determination on NiNPs/chitosan‐ MWCNTs and NiONPs/chitosan‐MWCNTs Modified Pencil Graphite Electrode

The rising amount of patients suffering for diabetes mellitus increases the requirements for effective insulin sensors. Carbon materials are a suitable choice for the development of insulin sensors due to their electrochemical characteristics. Pencil graphite electrodes (PGE) represent the trade‐off between price and excellent conductive properties. The modification of PGE by NiO and Ni nanoparticles fixed by chitosan results in surface area enlargement and improved electrocatalytic properties. This paper is focused on the comparison of different properties of Ni and NiO nanoparticles and their effect on redox reaction mechanism of insulin and detection characteristics. The electrode modified by Ni nanoparticles displays linear range of 1 μM–5 μM (R² 0.80), limit of detection (LOD) of 4.34 μM and sensitivity of 0.12 μA/μM. On the other hand, the electrode modified by NiO nanoparticles displays enhanced electrochemical characteristics such as linear range of 0.05 μM–5 μM (R² 0.99), limit of detection of 260 nM and sensitivity of 0.64 μA/μM. These properties make the NiO nanoparticles modified PGE the appropriate candidate for insulin determination.     

Li0.68Ni1.32O2/Ag nanocomposite: A Li-intercalation anode material with higher coulombic efficiency and better cycling performance

NiO, Li_0.68Ni_1.32O₂ and Li_0.68Ni_1.32O₂/Ag composite as anodes for Li-ion batteries are reported. Li_0.68Ni_1.32O₂ decomposed to Ni and Li₂O when discharged to 0.02 V, according to XRD analysis, which was similar to NiO. Increased initial coulombic efficiency was obtained for the Li_0.68Ni_1.32O₂ electrode (73%), higher than that of NiO (64.9%), but its cycling performance became worse because poorer conductive Li₂O formed when the first discharge process was finished. However, the Li_0.68Ni_1.32O₂/Ag electrode exhibited better cycling performance than NiO and Li_0.68Ni_1.32O₂, because the Ag nanoparticles in the composite improved the conductivity of the electrode. The initial coulombic efficiency for Li_0.68Ni_1.32O₂/Ag is still as high as 72%, nearly the same as that of Li_0.68Ni_1.32O₂.