Simultaneous determination of238Pu,239+240Pu,241Pu,241Am,242Cm,244Cm,89Sr,and90Sr in vegetation samples,and application to Chernobyl-fallout contaminated grass

A radiochemical procedure is described for the simultaneous determination of²³⁸Pu,^239+240Pu,²⁴¹Pu,²⁴¹Am,²⁴²Cm,²⁴⁴Cm,⁸⁹Sr, and⁹⁰Sr in vegetation samples. The method was applied for the determination of these, radionuclides in grass, collected near Munich after the fallout from the reactor accident at Chernobyl, USSR. The specific activities observed were (in Bq kg^–1 dry weight):²³⁸Pu, 0.077;^239+240Pu, 0.15;²⁴¹Pu, 3.9;²⁴¹Am, 0.031;²⁴²Cm, 3.0;²⁴⁴Cm, 0.008;⁸⁹Sr, 2000;⁹⁰Sr, 99.     

Radiochemical determination of the yields of transuranium nuclides produced from natural uranium irradiated in a reactor

Transuranium nuclides were produced by irradiating a pellet of natural uranium sulfide in the Japan Material Testing Reactor (JMTR). After irradiation, a successive separation of uranium, plutonium, americium and curium was carried out. The fractional concentrations of the nuclides²³⁸Pu,²³⁹Pu,²⁴⁰Pu,²⁴¹Am,²⁴³Am,²⁴²Cm and²⁴⁴Cm were determined by α-ray spectrometry, and those of²⁴¹Pu and^242mAm were estimated from the build-up of α-emitting daughters,²⁴¹Am and²⁴²Cm, respectively. As the yield of²⁴²Pu was too slight to be detected by α-counting, the neutron activation analysis of the plutonium fraction based on the²⁴²Pu(n, γ)²⁴³Pu reaction was carried out by γ-ray spectrometry, and it was shown that a few pg of²⁴²Pu could be determined. A burn-up of²³⁵U was also estimated by neutron activation analysis. The experimental results are compared with the calculated ones.     

Simultaneous electrodeposition of actinides

A new system for simultaneous electrodeposition of U, Np, Pu, Am and Cm has been developed. The system consists of (NH₄)₂C₂O₄–H₂SO₄–HCl. The effects on recovery of pH, current density, interfering ions and the amount of added HCl have been studied. The optimum condition for simultaneous electrodeposition of actinides has been recommended. Under the recommended condition recoveries of U, Np, Pu, Am and Cm have been obtained by using²³²U,²³⁷Np,²⁴¹Am,²⁴²Pu and²⁴⁴Cm. The counting sources prepared are uniform, adherent and suitable for -spectrometry.     

Application of instrumental radioanalytical techniques to nuclear waste testing and characterization

This paper describes the validation of a multi-technique analytical methodology that uses inductively coupled plasma-mass spectrometry, α-spectrometry, and γ-spectrometry for the routine analysis of samples containing transuranic radionuclides. This methodology is capable of the determination of concentrations of both²³⁸Pu and²⁴¹Pu in the presence of²³⁸U and²⁴¹Am without the need for chemical separations. The relative merits of these three techniques were evaluated as they are applied in a nuclear waste material and spent nuclear fuel testing program by analytical (1) standards and (2) solutions prepared from the dissolution of glasses doped with²³⁷Np,²³⁹Pu, and²⁴¹Am. The uncertainty associated with technique was within ±4% for standards and ±10% for doped nuclear waste glasses. The methodology was then used to analyze three fully radioactive waste glasses.     

Enzymatic degradation of large vegetation samples for the simultaneous determination of129I,actinides and strontium

A radiochemical procedure is given for the simultaneous determination of low levels of¹²⁹I, actinides (Pu, Am, Cm) and⁹⁰Sr in vegetation samples. It is shown that grass samples up to 5 kg fresh weight can be wet ashed conveniently by hydrogen peroxide under alkaline conditions, subsequent to an initial enzymatic disintegration. After purification of the iodine fraction,¹²⁹I is determined by neutron activation analysis. Using alpha spectrometry,²³⁸Pu and^239,240Pu are determined in the plutonium fraction, and²⁴¹Am,²⁴²Cm, and²⁴⁴Cm in the americium/curium fraction. The⁹⁰Sr is determined after separation by beta counting its decay product⁹⁰Y.     

Radiological characterization of low-and intermediate-level radioactive wastes

An analytical procedure for the determination of activation products ²³⁸Pu, ²⁴¹Pu, ²³⁹Pu/²⁴⁰Pu, ²⁴¹Am, ²³⁷Np, and a fission product ⁹⁰Sr in radioactive wastes is presented. Samples were decomposed using Fenton’s reaction. The separation was performed by anion-exchange chromatography, extraction chromatography, using TRU and Srresin, and precipitation techniques, followed by α-spectrometry and LSC counting. Tracer solutions and pure ion exchange resins were used to prepare artificial samples and trace nuclides during the analytical procedure. Some real samples of spent ion-exchange resins originating from our TRIGA Mark II research reactor were analyzed.     

<Superscript>237</Superscript>Np in peat and lichen in Finland

Activity concentrations of ²³⁷Np in peat and lichen samples in Finland were determined and contributions from nuclear weapons testing in 1950–1960s and the Chernobyl accident were estimated. ²³⁷Np was determined with ICP-MS using ²³⁵Np as a tracer. Activity concentrations of ²³⁷Np in peat samples varied between 1.98 ± 0.05 and 14.1 ± 0.3 mBq/m². The contribution from the Chernobyl accident to the total ²³⁷Np deposition in peat was 0.1–13%, the Chernobyl-derived fraction of total ²³⁷Np in peat being much lower than the previously determined corresponding Chernobyl-derived fractions of ^239+240Pu, ²⁴¹Pu, ²⁴¹Am and ²⁴⁴Cm.     

Distribution and behaviour of99Tc,237Np,239,240Pu,and241Am in the coastal and estuarine sediments of the Irish Sea

Intertidal coastal and estuarine sediments from 24 sites in the Irish Sea have been analyzed for⁹⁹Tc,²³⁷Np,²³⁸Pu,^239,240Pu and²⁴¹Am. The²³⁷Np activity and²³⁹Pu/²⁴⁰Pu ratio were measured simultaneously by ICP-MS, and⁹⁹Tc was determined by HR-ICP-MS which is ten times more sensitive than Q-ICP-MS.The activities of⁹⁹Tc,²³⁷Np,^239,240Pu and²⁴¹Am were distributed over a wide range of 1.5–70.5, 0.01–13.3, 2.3–1589, 2.6–1894 Bq/kg, respectively. Activities of these radionuclides decreased exponentially with distance from the Sellafield source. The²⁴¹Am/^239,240Pu and²³⁷Np/^239,240Pu ratios were almost constant with distance from the Sellafield. This result suggests that the distribution and behavior of Np and Pu are controlled by complicated factors such as the influence of transport, the variation with time of Np/Pu ratio in the Sellafield discharges and sedimentary mixing processes in the Irish Sea.     

Sequential separation of transuranic elements and fission products from uranium metal ingots in electrolytic reduction process of spent PWR fuels

A sequential separation procedure has been developed for the determination of transuranic elements and fission products in uranium metal ingot samples from an electrolytic reduction process for a metallization of uranium dioxide to uranium metal in a medium of LiCl-Li₂O molten salt at 650 °C. Pu, Np and U were separated using anion-exchange and tri-n-butylphosphate (TBP) extraction chromatography. Cs, Sr, Ba, Ce, Pr, Nd, Sm, Eu, Gd, Zr and Mo were separated in several groups from Am and Cm using TBP and di(2-ethylhexyl)phosphoric acid (HDEHP) extraction chromatography. Effect of Fe, Ni, Cr and Mg, which were corrosion products formed through the process, on the separation of the analytes was investigated in detail. The validity of the separation procedure was evaluated by measuring the recovery of the stable metals and ²³⁹Pu, ²³⁷Np, ²⁴¹Am and ²⁴⁴Cm added to a synthetic uranium metal ingot dissolved solution.     

Analysis of radioactive metal ions in environmental and liquid effluent samples

This paper describes the development and validation of analytical procedures for the separation and determination of⁹⁰Sr,⁹⁰Y,²³⁸Pu,^239/240Pu,²⁴¹Am,²⁴¹Cm and^243/244Cm in liquid effluents and environmental samples. The procedures use supported reagents for extraction chromatography (reversed phase partition chromatography) that enable the separation of the analytes from a large number of other radionuclides present.     

Measurements of actinide nuclides in water samples from the primary circuit of a nuclear power plant

Weekly, consecutive primary coolant samples from a boiling water reactor have been analyzed for^{239, 240}Pu,²³⁸Pu+²⁴¹Am,²⁴²Cm and²⁴⁴Cm for about two years, and for²³⁸Pu,²⁴¹Pu and²⁴¹Am for one year. Concentration ranges are reported. Samples were prepared for counting either directly by evaporation or by chemical separation on BioRad AG 1×4 resin and subsequent electrolysis, and were counted in 20 cm dia Frish grid ionization chambers. Procedures are described. For most actinide nuclides, activity ratios in primary coolant were found to be different from those in worldwide fallout, thus allowing an identification of origin in the case, that actinides should be detected in the vicinity of a nuclear power station.     

Determination of plutonium,americium and curium in airborne effluents of nuclear power plants

A radiochemical method has been developed for the determination of²³⁸Pu,^{239, 240}Pu,²⁴¹Am,²⁴²Cm and²⁴⁴Cm in airborne effluents of nuclear power plants. The method involves conversion of transuranium elements to acid-soluble forms, dissolution, purification, electrodeposition and alpha spectrometric determination. Final recovery ranged from 69.0 to 75.4% for plutonium and from 26.8 to 68.3% for americium and curium.     

Chemical leaching behavior of237Np from intertidal coastal sediment in the Irish Sea

Chemical leaching experiments of²³⁷Np in the sediments from the Esk Estuary and the Ribble Estuary in the Irish Sea, U. K., have been carried out, in comparison with those of^{239, 240}Pu and²⁴¹Am, to understand the geochemical associations of these long-lived radionuclides with sediment. Experimental results show that partitioning behavior of²³⁷Np is obviously different from those of^{239, 240}Pu and²⁴¹Am.     

Sorption characteristics of237Np,238Pu and241Am in sedimentary materials

Adsorption experiments were performed to measure distribution coefficients of²³⁷Np(V),²³⁸Pu(IV) and²⁴¹Am(III) for sedimentary sequential chemical extraction of the adsorbed radionuclides was carried out with water, CaCl₂, KCl, NH₂OH−HCl, K-oxalate and H₂O₂ solutions, to elucidate their dominant sorption mechanisms. The distribution coefficient of²³⁷Np was two orders of magnitude smaller than that of²³⁸Pu and²⁴¹Am. Most of²³⁷Np adsorbed was extracted with CaCl₂ solution and its sorption was controlled by a reversible ion exchange reaction. The adsorbed²³⁸Pu was mainly extracted with NH₂OH−HCl+K-oxalate solution and its sorption was possibly controlled by irreversible reactions.     

Sequential determination of Am, Cm, Pu, Np and U by extraction chromatography

Environmental contamination by artificial radionuclides and the evaluation of their sources require precise isotopic analysis and accurate determination of actinide elements above all plutonium and americium. These can be achieved by alpha spectrometry or by inductively coupled plasma mass spectrometry (ICP-MS) after chemical separation. In the present work, a simple, rapid method has been developed for the sequential separation of actinide elements from aqueous solutions and their determination by alpha spectrometry. Extraction chromatography was applied to the separation of ²⁴¹Am, ²⁴⁴Cm, ^{239 + 240,238}Pu, ²³⁷Np and ^238,235,234U using microporous polyethylene supporting tri-n-octylamine as the stationary phase and hydrochloric acid with and without reducing agents as the mobile phase. Actinide in 9 M HCl solution is introduced into the anion exchange column; Pu (IV), Np (IV) and U(VI) are retained on the column while Am (III) and Cm passed through. Pu is eluted first, reductively, after which, Np and then U are eluted. The method can be applied to all aqueous solutions which do not contain strong complexing or precipitation agents for the elements considered.     

Sequential determination of actinide isotopes and radiostrontium in swipe samples

Assays of alpha- and beta-emitting radionuclides in swipe samples are often required to monitor the presence of removable surface contamination for radiological protection and control in nuclear facilities. Swipe analysis has also proven to be a very sensitive analytical technique to detect nuclear signatures for safeguard verification purposes. A new sequential method for the determination of actinide isotopes and radiostrontium in swipe samples, which utilizes a streamlined column separation with stacked anion and extraction chromatography resins, has been developed. To validate the separation procedure, spike and blank samples were prepared and analyzed by inductively coupled mass spectrometry (ICP-MS), alpha spectrometry and liquid scintillation (LS) counting. Low detection limits have been achieved for isotopic analysis of Pu (²³⁸Pu, ²³⁹Pu, ²⁴⁰Pu, ²⁴¹Pu), U (²³⁴U, ²³⁵U, ²³⁸U), Am (²⁴¹Am), Cm (²⁴²Cm, ^243/244Cm) and Sr (⁹⁰Sr) at ultra-trace concentration levels in swipe samples.     

Characterization of an Irish Sea radioactively contaminated marine sediment core by radiometric and mass spectrometric techniques

Summary A radioactively contaminated marine sediment core stemming from Irish Sea has been characterized by radiometric and mass spectrometric techniques as for ²³⁷Np, ²⁴¹Am, ²³⁹Pu, ²⁴⁰Pu, ²⁴¹Pu, ¹³⁷Cs and ¹⁵⁴Eu. The data obtained with independent methods in the framework of a QA/QC program as compared with the source term discharges, as well as with those reported in literature, are in good agreement.     

Anomalously high237Np in intertidal sediments from the Ribble Estuary in the Irish Sea

Depth profiles and inventories of²³⁷Np in sediment cores from the Ribble Estuary in the Irish Sea have been studied along with those of Pu isotopes,²⁴¹Am and¹³⁷Cs, to allow a more detailed look of anomalously high²³⁷Np content observed in this estuary previously. The comprehensive data obtained showed that the depth profiles of both²³⁷Np contents and²³⁷Np/^239,240Pu activity ratios were clearly different from those of^239,240Pu,²⁴¹Am, and¹³⁷Cs and their activity ratios. As much as 80–90% of²³⁷Np inventories (0.32–1.06 kBq/m²), found in three cores, were estimated to be derived from a source other than Sellafield, on the basis of comparison of the²³⁷Np/^239,240Pu inventory ratio (0.65–1.74%) found in the Ribble Estuary cores with those (0.10–0.16%) in the Ravenglass Estuary cores.     

Certified reference material for radionuclides in seawater IAEA-381 (Irish Sea Water)

A certified reference material (CRM) for radionuclides in seawater, IAEA-381 (Irish Sea Water), is described and the results of certification are presented. The material has been certified for nine radionuclides (⁴⁰K, ⁹⁰Sr, ¹³⁷Cs, ²³⁷Np, ²³⁸Pu, ²³⁹Pu,²⁴⁰Pu, ^239,240Pu and ²⁴¹Am). Information on massic activities with the corresponding 95% confidence intervals are given for eight radionuclides (³H, ¹²⁵Sb, ²³⁴U, ²³⁵U, ²³⁶U, ²³⁸U, ²⁴¹Pu and ²⁴⁴Cm). Less reported radionuclides include ⁶⁰Co, ⁹⁹Tc, and ²⁴²Pu. The CRM may be used for quality assurance/quality control of the analysis of radionuclides in environmental water samples, for the development and validation of analytical methods and for training purposes. The material is available from the IAEA in 5 kg units.     

Alpha spectrum evaluation method for the simultaneous determination of plutonium,americium and curium

A method based on the geometric progression decrease of the counts in the far tail of the alpha spectrum is described for the simultaneous determination of plutonium, americium and curium by alpha spectrometry. For evaluating the precision and accuracy, synthetic mixtures were prepared from solutions of enriched isotopes and sources were prepared by direct evaporation method using tetraethylene glycol /TEG/ as a spreading agent and electropolished stainless steel discs as the backing material. Precision and accuracy of about 1% is demonstrated in the determination of²⁴⁴Cm/²³⁹Pu,²⁴¹Am/²³⁹Pu,²⁴⁴Cm/²³³U,²⁴¹Am/²³³U and²³⁹Pu/²³³U alpha activity ratios using a 450 mm² silicon surface barrier detector.