Intense 974 nm emission from ErxYb2−xSi2O7 films through efficient energy transfer up-conversion from Er3+ to Yb3+ for Si solar cell

The optical properties of the Er_xYb_2?xSi₂O₇ thin films were investigated by photoluminescence measurements and the intense 974 nm light emission was observed. The 974 nm emission was mainly from the transition ²F_5/2 to ²F_7/2 level of Yb³⁺ upon exploring energy-transfer via up-conversion at Er^{3+ 4}I_13/2 level. Under 972 nm excitation, the lifetime at Er^{3+ 4}I_13/2 level reaches up to 4 ms for film containing 2 at% Er³⁺, while decreases to about 20 μs as the film is pumped by 488 nm. This confirmed that the energy transfer up-conversion process was the dominant transition at Er^{3+ 4}I_13/2 level. This may be of interest to improve the solar cells′ efficiency by placing this film at the rear of cell, converting the near-infrared photons between 1480 nm and 1580 nm to just above the Si bandgap.     

Enhanced infrared to visible upconversion emission in Er3+ doped phosphate glass: Role of silver nanoparticles

Phosphate glasses with compositions (59.5–x)P₂O₅–MgO–xAgCl–0.5Er₂O₃ (0.0≤x≤1.5 mol%) containing fixed concentration of Er³⁺ ion with and without silver nanoparticles (NPs) are prepared using melt quenching technique. The amorphous nature of the glass is confirmed using the X-ray diffraction method. The homogeneous distribution of spherical Ag NPs (average size ～37 nm) in the glassy matrix is evidenced from the transmission electron microscopy (TEM) analyses. The UV–vis–NIR absorption spectra shows 10 bands corresponding to ⁴I_13/2, ⁴I_11/2, ⁴I_9/2, ⁴F_9/2, ⁴S_3/2, ²H_11/2, ⁴F_7/2, ⁴F_5/2, ²G_9/2, ⁴G_11/2 transitions in which the most intense bands are ²H_11/2 and ⁴G_11/2. The absorption spectrum of Er³⁺ ions free glass sample containing Ag NPs displays a prominent surface Plasmon resonance (SPR) band located at 528 nm. The infrared to visible frequency upconversion (UC) emission under 797 nm excitation shows two emission bands green (⁴S_3/2–⁴I_15/2) and red (⁴F_9/2–⁴I_15/2) centered at 540 nm and 634 nm, respectively, corresponding to Er³⁺ transitions. An enhancement in UC emission intensity of green band (⁴S_3/2–⁴I_15/2) is observed in the presence of silver NPs and the maximum enhancement occurred for 1.5 mol% AgCl. However, the enhancement of emission intensity of the red band (⁴F_9/2–⁴I_15/2) is smaller. The enhancement of UC emission is understood in terms of the intensified local field effect due to silver NPs.     

Visible luminescence of nanocrystalline AlN:Er thin film by co-deposition of AlN,Er, and SiO2

We report a visible luminescence of Er³⁺ ions in an amorphous-nanocrystalline AlN:Er thin film prepared by co-deposition using AlN, Er, and SiO₂ targets. A PL emission spectrum of Er³⁺ in the AlN:Er film annealed at 750 °C showed a strong bluish green emission of Er³⁺ in the amorphous-nanocrystalline AlN:Er thin film, which is attributed to the intra-4fEr³⁺ transitions of ²H_11/2 → ⁴I_15/2 and ⁴F_7/2 → ⁴I_15/2. It was found that crystallite diameters were between 3 and 5 nm by high-resolution transmission electron microscopy. The occurrence of the strong Er³⁺ emission in the annealed AlN:Er thin film with a mixture of amorphous and nanocrystalline phases may be contributed to an increase in the number of excitation Er³⁺ centers and a presence of oxygen related to Er³⁺ excitation and recombination process in the AlN:Er thin film.     

Comparative study of the spectroscopic properties of Yb3+/Er3+ codoped tellurite glasses modified with R2O (R=Li,Na and K)

Spectroscopic characterization of Yb³⁺/Er³⁺ codoped TeO₂–R₂O–ZnO–Ln₂O₃ glasses as a function of network modifiers (R=Li, Na and K) has been investigated. The Judd–Ofelt parameters (Ω_t), quantum efficiency in near infrared (1.55 μm) and visible up-conversion (546 and 660 nm) and quality factor spectroscopy (χ) were calculated. Three up-conversion emission bands centered at 525, 546 and 660 nm were observed as maxima for glasses containing potassium. The measured lifetime of ⁴I_13/2, ⁴F_9/2 and ⁴S_3/2 from Er³⁺ and ⁴F_5/2 from Yb³⁺ levels increased when potassium (K) replaced lithium (Li) and Na. The maximum emission cross-section (ECS) for ⁴I_13/2→⁴I_15/2 transition of Er³⁺ was calculated to be 1.02×10^?20 cm² for TeO₂–Li₂O–ZnO–Ln₂O₃ glasses. The energy transfer efficiency (ET) from Yb³⁺ to Er³⁺, (⁴F_5/2)+(⁴I_15/2)→(⁴F_7/2)+(⁴I_13/2), was calculated using the measured lifetimes of Yb³⁺ with and without the presence of acceptor (Er³⁺). The maximum calculated ET was 58% for 0.25 mol% of Er³⁺ and 3 mol% of Yb³⁺ for TeO₂–K₂O–ZnO–Ln₂O₃ glass composition.     

Synthesis and luminescence properties of Gd6MoO12:Yb3+, Er3+ phosphor with enhanced photoluminescence by Li+ doping

Yb³⁺/Er³⁺ co-doped Gd₆MoO₁₂ and Yb³⁺/Er³⁺/Li⁺ tri-doped Gd₆MoO₁₂ phosphors were prepared by adjusting the annealing temperature via the high temperature solid-state method. Under the excitation of 980 nm semiconductor, the upconversion luminescence properties were investigated and discussed. In the experimental process, we get the optimum Yb³⁺ concentration and the concentration quench effect will happen while the concentration extends the given region. According to the Yb³⁺ concentration quenching effects, the critical distance between Yb³⁺ ions had been calculated. The measured UC luminescence exhibited a strong red emission near 660 nm and green emission at 530 nm and 550 nm, which are due to the transitions of Er³⁺(⁴F_9/2, ²H_11/2, ⁴S_3/2) → Er³⁺(⁴I_15/2). Then the effect of excitation power density in different regions on the upconversion mechanisms was investigated and the calculated results demonstrate that the green and red upconversion is a two-photon process. A possible mechanism was discussed. After Li⁺ ions mixing, the upconversion emission enhanced largely, and the optimum Li⁺ concentration was obtained while fixed the Yb³⁺ and Er³⁺ on the above optimum concentration. This enhancement owns to the decrease of the local symmetry around Er³⁺ after Li⁺ ions doping into the system. This result indicates that Li⁺ is a promising candidate for improving luminescence in some case.     

Microwave sol–gel derived NaCaGd(MoO4)3:Er3+/Yb3+ phosphors and their upconversion photoluminescence properties

Ternary molybdate NaCaGd_1−x(MoO₄)₃:Er³⁺/Yb³⁺ phosphors with the proper doping concentrations of Er³⁺ and Yb³⁺ (x = Er³⁺ + Yb³⁺, Er³⁺ = 0, 0.05, 0.1, 0.2 and Yb³⁺ = 0, 0.2, 0.45) were successfully synthesized by microwave sol–gel method for the first time. Well-crystallized particles formed after heat-treatment at 900 °C for 16 h showed a fine and homogeneous morphology with particle sizes of 3–5 μm. The optical properties were examined comparatively using photoluminescence emission and Raman spectroscopy. Under excitation at 980 nm, the doped particles exhibited a strong 525-nm emission band, a weak 550-nm emission band in the green region, which correspond to the ²H_11/2 → ⁴I_15/2 and ⁴S_3/2 → ⁴I_15/2 transitions, and a very weak 655-nm emission band in the red region, which corresponds to the ⁴F_9/2 → ⁴I_15/2 transition. The optimal Yb³⁺:Er³⁺ ratio was obtained to be 9:1, as indicated by the composition-dependent quenching effect of Er³⁺ ions. The pump power dependence of upconversion emission intensity and Commission Internationale de L’Eclairage chromaticity coordinates of the phosphors were evaluated in detail.     

Positive influence of Tm3+ on effective Er3+: 3 μm emission in fluoride glass under 980 nm excitation

Er³⁺ and Tm³⁺ singly doped and codoped new fluoride glasses were prepared by traditional melt-quenching method. Efficient 3 μm emission was obtained under 980 nm laser excitation. It is worthy to notice that one of the two ions can be the sensitizer to the other one by depressing the Er³⁺: 1.5 μm emission through the energy transfer process from Er³⁺:⁴I_13/2 level to Tm³⁺:³F₄ level. On the basis of measured absorption spectra, the Judd-Ofelt intensity parameters and radiation emission probability were calculated to evaluate the spectroscopic properties. Additionally, the micro-parameters together with the phonon assistance of Er³⁺:⁴I_13/2 → Tm³⁺:³F₄ and Er³⁺:⁴I_11/2 → Tm³⁺:³H₅ processes were quantitatively analyzed by using Dexter model. The theoretical micro-parameters results meet well with the experiments which indicates that Er³⁺/Tm³⁺ codoped fluoride glass is a potential kind laser glass for 3 μm laser.     

Thermal stability and spectroscopic properties of erbium-doped niobic-tungsten–tellurite glasses for laser and amplifier devices

Er³⁺ doped niobic-tungsten–tellurite glasses doped with concentration of Er³⁺ ion up to 3 wt% were fabricated. The effect of Er³⁺ doping concentration on thermal stability and optical properties was investigated in order to obtain the most suitable rare earth content for developing 1.5 μm compact fiber amplifier pumped with a commercial telecom 980 nm laser diode. The maximum doping concentration allowed was found to be around 1.77×10²⁰ ions/cm³, for which a broad 1.5 μm emission spectra of 65 nm FWHM and a lifetime of 3.4 ms for the ⁴I_13/2 level was measured.     

Near-infrared broadband luminescence and energy transfer in Bi–Tm–Er co-doped lanthanum aluminosilicate glasses

The Bi–Tm–Er co-doped SiO₂–Al₂O₃–La₂O₃ (SAL) glasses, which exhibited a broadband near-infrared (NIR) emission, were investigated by the optical absorption and photoluminescence spectra. A super broadband NIR emission extending from 0.95 to 1.6 μm with a full-width at half-maximum (FWHM) of 430 nm which covered the whole O, E, S, C and L bands, was observed in Bi–Tm–Er co-doped samples under 808 nm excitation, as a result of the overlap of the Bi-related emission band (centered at 1270 nm) and the emission from Tm^{3+ 3}H₄→³F₄ transition (1450 nm) as well as Er^{3+ 4}I_13/2→⁴I_15/2 transition (1545 nm). In addition, a super broadband emission with amplitude relatively flat from 0.95 to 2.1 μm has been observed. The possible energy transfer between Bi-related centers, Tm³⁺ ions and Er³⁺ ions was proposed.     

Optical characterization of Er3+and Yb3+ co-doped barium fluorotellurite glass

Spectroscopic studies of Er³⁺/Yb³⁺ co-doped (Ba,La)-fluorotellurite glass composition have been carried out using standard experimental and theoretical methods. Quantitative analyses of the room temperature absorption and emission spectra as well as the emission lifetimes yield various important spectroscopic parameters such as the radiative decay rates, fluorescence branching ratios, and emission/absorption cross sections. In addition, internal radiative quantum yields have been determined for the infrared emission at 1571 nm and for the upconversion emission at 547 nm. The influence of various non-radiative properties such as multiphonon relaxation, concentration quenching, and quenching by hydroxyl radicals have also been quantitatively estimated and correlated with the observed spectral properties. The comparative studies with the other composition of tellurite and different glasses showed that present glass composition could be a potential candidate for the broadband amplifier.     

Temperature measurements inside an Er3+–Yb3+ co-doped fluoride crystal heated by a NIR laser diode and probed by red-to-green upconversion

The temperature of a transparent Cd_0.7Sr_0.3F₂: Er³⁺(4%)–Yb³⁺(6%) crystalline plate 0.3 mm thick heated by a near-infrared (974 nm) laser diode and probed by a red (652 nm) laser was accurately evaluated as a function of the infrared power absorbed by the Yb³⁺ ions.The green emission generated by the Er³⁺ ions directly excited by the red laser consists of three major lines (coming from three individual Stark levels in thermal equilibrium) whose intensities were measured according to the absorbed infrared power and the distance between the heated and probed volumes, to evaluate the heating induced by the excitation of Yb³⁺ and Er³⁺ ions at 974 nm by applying the Boltzmann's equation linking the populations of emitting levels to the temperature. In the case where the Yb³⁺ ions excited by the laser diode are situated at a distance of about 0.5 mm from the edge of the crystal and for an absorbed infrared power of 100 mw, the crystal's edge temperature is reaching 80 °C after 20 s of continuous excitation at 974 nm.     

Up conversion luminescence of Yb3+–Er3+ codoped CeO2 nanocrystals with imaging applications

The effects of Yb³⁺ doping on up conversion in Yb³⁺–Er³⁺ co-doped cerium oxide nanocrystals are reported. Green emission around 545 and 560 nm attributed to the ²H_11/2, ⁴S_3/2→⁴I_15/2 transitions and red emission around 660 and 680 nm due to ⁴F_9/2→ ⁴I_15/2 transitions under 975 nm excitation were studied at room temperature. Both green and red emission intensities increase as the Yb³⁺ concentration increases from 0%. Emission strength starts to decrease after the Yb³⁺ concentration exceeds a critical amount. The green emission strength peaks around 1% Yb³⁺ concentration while the red emission strength peaks around 4%. An explanation of competition between different decay mechanisms is presented to account for the luminescence dependence on Yb³⁺ concentration. Also, the application of up converting nanoparticles in biomedical imaging is demonstrated.     

Upconversion photoluminescence properties of SrY2(MoO4)4:Er3+/Yb3+ phosphors synthesized by a cyclic microwave-modified sol–gel method

SrY_2−x(MoO₄)₄:Er³⁺/Yb³ phosphors with doping concentrations of Er³⁺ and Yb³⁺ (x = Er³⁺ + Yb³⁺, Er³⁺ = 0.05, 0.1, 0.2 and Yb³⁺ = 0.2, 0.45) have been successfully synthesized by a cyclic microwave-modified sol–gel method, and the upconversion photoluminescence properties have been investigated. Well-crystallized particles showed a fine and homogeneous morphology with particle sizes of 1–3 μm. Under excitation at 980 nm, SrY₂(MoO₄)₄:Er³⁺/Yb³⁺ particles exhibited a strong 525-nm, weak 550-nm emission bands in the green region, and a very weak 655-nm emission band in the red region. The possible mechanism of the green and red emissions was discussed in detail under consideration of a two-photon process. The Raman spectra of the particles indicated the presence of strong peaks at both higher and lower frequencies.     

Upconversion emission in CaTiO3:Er3+ nanocrystals

CaTiO₃:Er³⁺ (5%) nanocrystals were obtained by sol–gel method under acidic conditions. The sizes of nanocrystals were 40 nm. Strong green anti-Stokes emission was observed after excitation of the ⁴I_9/2 and ⁴I_11/2 level. The emission is due to excited state absorption (ESA) and energy transfer upconversion (ETU).     

Fabrication and luminescence behavior of phosphate glass ceramics co-doped with Er3+ and Yb3+

Transparent phosphate glass ceramics co-doped with Er³⁺ and Yb³⁺ in the system P₂O₅Li₂OCaF₂TiO₂ were successfully synthesized by melt-quenching and subsequent heating. Formation of the nanocrystals was confirmed by X-ray powder diffraction. Judd–Ofelt analyses of Er³⁺ ions in the precursor glasses and glass ceramics were performed to evaluate the intensity parameters Ω_2,4,6. Under 975 nm excitation, intense upconversion (UC) and infrared emission (1545 nm) were observed in the glass ceramics by efficient energy transfer from Yb³⁺ to Er³⁺. The luminescence processes were explained and the emission cross section was calculated by Fuchtbauer–Ladenburg (F–L) formula. The results confirm the potential applications of Er³⁺/Yb³⁺ co-doped glass ceramics as laser and fiber amplifier media.     

Erbium-doped lead silicate glass for near-infrared emission and temperature-dependent up-conversion applications

Erbium-doped lead silicate glass has been investigated for near-infrared emission and up-conversion applications. Near-infrared emission due to ⁴I_13/2 → ⁴I_15/2 transition of Er³⁺ is relatively broad (70.5 nm) and long-lived (3.7 ms). Also, up-conversion luminescence spectra of Er³⁺ ions in lead silicate glass have been examined as a function of temperature. The relative intensities of luminescence bands corresponding to ²H_11/2 → ⁴I_15/2 and ⁴S_3/2 → ⁴I_15/2 transitions of Er³⁺ were determined with temperature. The fluorescence intensity ratio and temperature sensitivity were calculated. The maximum sensitivity for Er³⁺ doped lead silicate glass is close to 26.4 × 10^?4 K^?1 at T = 590 K.     

Quasi-one dimensional Er3+–Yb3+ codoped single-crystal MoO3 ribbons: Synthesis,characterization and up-conversion luminescence

The quasi-one dimensional (Q1D) Er³⁺–Yb³⁺ codoped single-crystal MoO₃ ribbons with width range from 1 to 5 μm, and maximum length about 30 μm have been synthesized by the vapor transport method. The samples were characterized using X-ray diffraction, scanning electron microscopy, transmission electron microscope, and luminescence spectra. By a 975 nm laser diode (LD) as excitation source, the blue, green and red emission bands centered at about 408, 532, 553 and 657 nm were detected, which attributed to the ²H_9/2 → ⁴I_15/2, ²H_11/2, ⁴S_3/2 → ⁴I_15/2 and ⁴F_9/2 → ⁴I_15/2 transitions of Er³⁺, respectively. The three-, and two-photon process was responsible for the blue, green and red up-conversion emissions mechanism for the Q1D Er³⁺–Yb³⁺ codoped single-crystal MoO₃ ribbons, respectively. The results suggested that the Q1D Er³⁺–Yb³⁺ codoped single-crystal MoO₃ ribbons will have potential applications in remote bio-imaging and surface enhanced Raman scattering.     

Photoluminescence investigations of Li2SiO3:Ln (Ln=Er3+, Eu3+, Dy3+, Sm3+) phosphors

In this study, we report a comprehensive structural and photoluminescence (PL) study on lithium metasilicate (Li₂SiO₃) phosphor ceramics doped with four rare earth (RE) ions. X-ray diffraction (XRD) patterns show a dominant phase, characteristic of the orthorhombic structure Li₂SiO₃ compound and the presence of dopants has no effect on the basic crystal structure of the material. The first excited state Er³⁺ luminescence at 1.54 μm arises from a sharp atomic-like radiative transition between the ⁴I_13/2 state and the ⁴I_15/2 state (ground level) under a 532 nm line of an Ar ion laser excitation. Sm doped samples showed Sm³⁺ emission characteristics corresponding to the some ⁴G_5/2→⁶H_j (j=5/2,9/2,11/2) transitions indicating a strong crystal-field effect. PL spectra of Eu doped material exhibited peaks corresponding to the ⁵D₀→⁷F_j (j=0,1,2,3 and 4) transitions under 405 nm excitation. The dominant red color emission at 612 nm from the hypersensitive (⁵D₀→⁷F₂) transition of Eu³⁺ indicates the inversion antisymmetry crystal field around Eu³⁺ ion, which is favorable to improve the red color purity. Dy doped samples showed the Dy³⁺ emission characteristic due to the ⁴F_9/2→⁶H_13/2 transition. Their relative intensity ratios also suggested the presence of a symmetric environment around the metal ion. We suggest that lithium metasilicate has enough potential candidates to be a phosphor material.     

Synthesis and near-infrared luminescence properties of LaOCl:Nd3+/Yb3+

Near-infrared emitting phosphors LaOCl:Nd³⁺/Yb³⁺ were prepared by the solid-state method, and their structures and luminescent properties were investigated by using X-ray diffraction and photoluminescence analysis, respectively. The studies shows that tetragonal LaOCl:Nd³⁺/Yb³⁺ can be synthesized by the solid-state reaction at 600 °C for 3 h. Upon 353 nm UV excitation, LaOCl:Nd³⁺/Yb³⁺ sample shows strong near-infrared emission lines in the region of 1060–1150 nm (corresponding to ⁴F_3/2 → ⁴I_J′ transition of Nd³⁺, J′ = 9/2, 11/2, 13/2, 15/2) and 980–1050 nm (corresponding to ²F_5/2 → ²F_7/2 transition of Yb³⁺). The decreasing emission intensity of Nd³⁺ with increasing doping concentration of Yb³⁺ proved the energy transfer in LaOCl:Nd³⁺/Yb³⁺. The possible near-infrared emission and energy transfer mechanism between Nd³⁺ and Yb³⁺, as well as the energy transfer efficiency of LaOCl:Nd³⁺/Yb³⁺ were discussed.     

Intrinsic pinning properties of FeSe0.5Te0.5

The intrinsic pinning properties of FeSe_0.5Te_0.5, which is a superconductor with a critical temperature T_c of approximately 14 K, were studied through the analysis of magnetization curves obtained using an extended critical state model. For the magnetization measurements carried out with a superconducting quantum interference device (SQUID), external magnetic fields were applied parallel and perpendicular to the c-axis of the sample. The critical current density J_c under the perpendicular magnetic field of 1 T was estimated using the Kimishima model to be equal to approximately 1.6 × 10⁴, 8.8 × 10³, 4.1 × 10³, and 1.5 × 10³ A/cm² at 5, 7, 9, and 11 K, respectively. Furthermore, the temperature dependence of J_c was fitted to the exponential law of J_c(0) × exp(?αT/T_c) up to 9 K and the power law of J_c(0) × (1 ? T/T_c)ⁿ near T_c.