Fabrication of Gd0.5Sr0.5CoO3 film for SOFC cathode by pulsed laser deposition

Gd_0.5Sr_0.5CoO₃ (GSCO) film has been fabricated by pulsed laser deposition (PLD) to be used as the cathode of the solid oxide fuel cell (SOFC). The GSCO thin film obtained has a columnar crystalline structure so that it will have a high permeation property. The PLD technique has been found suitable for growing a film of complex composition because of its good control of stoichiometry and thus for fabricating a GSCO film used as the cathode of the SOFC. The GSCO film has been studied for porosity electrical conductivity and power density. The GSCO film grown at a substrate temperature of 1100 K and oxygen gas pressure of 100 Pa has high electrical conductivity which is 820 S cm^− 1 at 973 K with post annealing at a rather low temperature (1000 K). This value is higher than that of the GSCO film prepared by RF-sputtering with post annealing at a higher temperature (1273 K).     

Mesopore size dependence of the ionic diffusivity in alumina based composite lithium ionic conductors

Ordered-mesoporous Al₂O₃ was synthesized by a sol–gel method using neutral copolymer surfactants as structure-directing agents. The pore size was controlled over the 3–15 nm range by the use of various surfactants. Composites composed of the synthesized mesoporous Al₂O₃ and a lithium ion conductor (LiI) were prepared. The maximum dc electrical conductivity, 2.6 × 10^− 4 S cm^− 1 at 298 K, was observed for 50 LiI·50 Al₂O₃ composite with 4.2 nm average mesopore size, which was considerably higher than the previously reported LiI-alumina composites. A systematic dependence of conductivity upon pore size was observed, in which conductivity increased with decreasing pore size, except for samples with a pore size of 2.8 nm. The lithium ion diffusion coefficient determined by the ⁷Li pulsed field gradient nuclear magnetic resonance (PFG-NMR) showed excellent agreement with the measured conductivity calculated by the Nernst-Einstein equation. On the other hand, lithium migration activation energies obtained by quasielastic neutron scattering (QENS) and ⁷Li NMR spin-lattice relaxation time (T₁) were considerably smaller than those obtained from electrical conductivity and PFG-NMR. This could be explained by the ion migration mechanism in heterogeneous composites and a possible enhancement of conductivity in mesoscopically confined spaces.     

High lithium ion conductivity glass-ceramics in Li2O–Al2O3–TiO2–P2O5 from nanoscaled glassy powders by mechanical milling

Mechanical milling (MM) has been used to prepare the nanosized Li_1.4Al_0.4Ti_1.6(PO₄)₃ (denoted LATP) glassy powders, which was converted into glass-ceramics through thermal treating at 700–1000 °C. The XRD, TEM, FESEM and ac impedance techniques were used to characterize the products. The results showed that completely amorphous products were prepared by MM for 40 h, and single-phase LiTi₂(PO₄)₃-type structured glass-ceramics were obtained by further heat treatment. The lithium ion conductivity of the glass-ceramics increased with the growth of the crystalline phase and decrease of the grain size. The highest bulk conductivity (σ_b) of 1.09 × 10^− 3 S cm^− 1 with an energy of activation as low as 0.28 eV was obtained at room temperature for the specimen treated at 900 °C for 6 h. The high conductivity, easy fabrication and low cost make the LATP glass-ceramics promising to be used as inorganic solid electrolyte for all-solid-state Li-ion rechargeable batteries.     

High lithium ion conducting glass-ceramics in the system Li2S–P2S5

Highly ion-conductive Li₂S–P₂S₅ glass-ceramic electrolytes were prepared by controlling the compositions and heat treatment temperatures of the glasses. The 70Li₂S·30P₂S₅ (mol%) glass-ceramic heated at 360 °C showed the highest conductivity of 3.2 × 10^− 3 S cm^− 1 at room temperature and the lowest activation energy of 12 kJ mol^− 1 for conduction in the binary system Li₂S–P₂S₅. The outstanding property was attributed to both the precipitation of the new crystal as a metastable phase and the increase in crystallinity of the phase. With increasing heat treatment temperatures, the metastable phase changed into thermodynamically stable phases such as the Li₄P₂S₆ crystal by heat treatment up to 550 °C, resulting in low conductivities of the glass-ceramics. It was, thus, found that the formation of superionic metastable phases by heating the Li₂S–P₂S₅ glasses is responsible for the marked enhancement on the conducting properties of the glass-ceramics.     

Ion and electron conduction in SrFe1−xScxO3−δ

The oxygen ion and electron transport in SrFe_1−xSc_xO_3−δ  (x = 0.1–0.3) system at 700–950 °C were studied analyzing the total conductivity dependencies on the oxygen partial pressure, pO₂. The conductivity measurements were performed both under reducing conditions (10^− 19 ≤ pO₂ ≤ 10^− 8 atm) comprising the electron-hole equilibrium point, and in oxidizing atmospheres (10^− 5 ≤ pO₂ ≤ 0.5 atm) which are characterized by extensive variations of the oxygen content studied by coulometric titration technique. The incorporation of 10% Sc³⁺ cations into the iron sublattice suppresses transition of the cubic perovskite phase into vacancy-ordered brownmillerite, thus improving ion conduction at temperatures below 850 °C. When scandium content increases, the ion conductivity becomes considerably lower. The hole mobility is thermally-activated and varies in the range of 0.001 to 0.05 cm² V^− 1 s^− 1, increasing with oxygen concentration and decreasing on Sc doping.     

Inorganic polymer phosphazene disulfide as cathode material for rechargeable lithium batteries

Novel inorganic network polymer phosphazene disulfide [(NPS₂)₃]_n was synthesized by a solution cross-link method. IR and element content analysis confirmed the polymer's molecular structure. The polymer has an average particle size of d_0.5 = 7.7 μm and the specific surface area is 57.4 m² g^− 1. TG/DTA analysis showed that [(NPS₂)₃]_n underwent a decomposition reaction from 200 to 300 °C. When used as cathode material in lithium batteries, its initial discharge capacity was 459.1 mAh g^− 1, which is almost 93.5% of theoretical specific capacity (490.9 mAh g^− 1). After 30 charge–discharge cycles, the discharge capacity of [(NPS₂)₃]_n stabilized at approximately 400.1 mAh g^− 1 which revealed an excellent cyclic ability. Therefore [(NPS₂)₃]_n is of great potential as cathode material for secondary lithium batteries.     

Ionic and electronic conductivities,stability and thermal expansion of La10 − x(Si,Al)6O26 ± δ solid electrolytes

Apatite-type La_10 − xSi_6 − yAl_yO_{27 − 3x/2 − y/2} (x = 0–0.33; y = 0.5–1.5) exhibit predominant oxygen ionic conductivity in a wide range of oxygen partial pressures. The conductivity of silicates containing 26.50–26.75 oxygen atoms per formula unit is comparable to that of gadolinia-doped ceria at 770–870 K. The average thermal expansion coefficients are (8.7–10.8) × 10^− 6 K^− 1 at 373–1273 K. At temperatures above 1100 K, silicon oxide volatilization from the surface layers of apatite ceramics and a moderate degradation of the ionic transport with time are observed under reducing conditions, thus limiting the operation temperature of Si-containing solid electrolytes.     

Synthesis and characterization of (Pr0.75Sr0.25)1 − xCr0.5Mn0.5O3 − δ as anode for SOFCs

The complex perovskite (Pr_0.75Sr_0.25)_1 − xCr_0.5Mn_0.5O_3 − δ (PSCM) has been prepared and studied as possible anode material for high-temperature solid oxide fuel cells (SOFCs). PSCM exhibits GdFeO₃-type structure and is both physically and chemically compatible with the conventional YSZ electrolyte. The reduction of PSCM resulted in structural change from orthorhombic Pbnm to cubic Pm-3m. Selected area electron diffraction (SAED) analysis on the reduced phases indicated the presence of a √2 × √2 × 2 superlattice. The total conductivity values of ∼ 75% dense Pr_0.75Sr_0.25Cr_0.5Mn_0.5O_3 − δ at 900 °C in air and 5% H₂/Ar are 9.6 and 0.14 S cm^− 1 respectively. The conductivity of PSCM drops with decreasing Po₂ and is a p-type conductor at all studied Po₂. The average TEC of Pr_0.75Sr_0.25Cr_0.5Mn_0.5O_3 − δ is 9.3 × 10^− 6 K^− 1, in the temperature range of 100–900 °C and is close to that of YSZ electrolyte. The anode polarization resistance of PSCM in wet 5%H₂ is 1.31 Ω cm² at 910 °C and in wet CH₄ at 930 °C; the polarization resistance is 1.29 Ω cm². PSCM was unstable at 900 °C in unhumidified hydrogen. Cell performance measurements carried out using graded PSCM and La_0.8Sr_0.2MnO₃ as anode and cathode respectively yielded a maximum power density of 0.18 W cm^− 2 in wet 5%H₂/Ar at 910 °C and the corresponding current density was 0.44 A cm^− 2 at 0.4 V. The activation energy for the electrochemical cell operating in wet (3% H₂O) 5%H₂/Ar fuel is 85 kJ mol^− 1.     

Structural,XPS and impedance analysis of LixCoVO4 (x = 0.8, 1.0, 1.2)

Lithium cobalt vanadate Li_xCoVO₄ (x = 0.8; 1.0; 1.2) has been prepared by a solid state reaction method. The XRD analysis confirms the formation of the sample. A new peak has been observed for Li_1.0CoVO₄ and for Li_1.2CoVO₄ indicating the formation of a new phase. The XPS analysis indicates the reduction in the oxidation of vanadium and oxygen with the addition of Li in Li_xCoVO₄ (x = 0.8, 1.0, 1.2). The impedance analysis gives the conductivity value as 2.46 × 10^− 5, 6.16 × 10^− 5, 9 × 10^− 5 Ω^− 1 cm^− 1 for Li_xCoVO₄ (x = 0.8; 1.0; 1.2), all at 623 K. The similarity in the bulk activation energy (E_a) and the activation enthalpy for migration of ions (E_ω) indicate that the conduction in Li_1.2CoVO₄ has been due to hopping mechanism.     

Nanostructured Cu-CGO anodes fabricated using a microwave-assisted glycine–nitrate process

This work reports a study of nanostructured copper-doped gadolinium cermet (Cu-CGO) composite anodes prepared via conventional synthesis (CS) and microwave-synthesis (MS) involving the glycine–nitrate process (GNP). A detailed investigation on the mechanical properties, electrical conductivity and electrochemical performance of prepared Cu_0.5(Ce_0.9Gd_0.1)_0.5O_2−δ anodes is included. The prepared samples were characterized by techniques, such as XRD, EDX, SEM and electrical characterizations. After reduction in 10% H₂ and 90% N₂, the DC conductivities of the Cu-CGO anodes prepared via CS-GNP and MS-GNP are found to be 5.43×10³ and 1.09×10⁴ S cm⁻¹ at 700 °C, respectively. The electrochemical performances of the spin-coated anode symmetrical cells sintered at 700 °C are evaluated at cell operating temperatures of 600, 700 and 800 °C. The lowest area specific resistance (ASR) values for the Cu-CGO/CGO/Cu-CGO symmetrical cells prepared via the MS-GNP route at operating temperatures of 600, 700 and 800 °C are found to be 0.34, 0.71 and 1.10 Ω cm², respectively. The as-prepared (via MS-GNP) Cu-CGO anode exhibits excellent electrical and electrochemical performance consistent with the uniform nanostructured morphology compared with the anode prepared via CS-GNP.     

Physical,electrochemical and supercapacitive properties of activated carbon pellets from pre-carbonized rubber wood sawdust by CO2 activation

The physical and electrochemical properties of the activated carbon pellet electrodes have been investigated. Activated carbon pellets were prepared from single step carbonization process of pre-carbonized rubber wood sawdust at a temperature of 800 °C that followed with a CO₂ activation process at temperature in the range of 700–1000 °C. The BET characterization on the sample found that the surface area of the carbon pellet increased with the increasing of the activation temperature. The optimum value was as high as 683.63 m² g⁻¹. The electrical conductivity was also found to increase linearly with the increasing of the activation temperature, namely from 0.0075 S cm⁻¹ to 0.0687 S cm⁻¹ for the activation temperature in the range of 700–1000 °C. The cyclic voltammetry characterization of the samples in aqueous solution of 1 M H₂SO₄ also found that the specific capacitance increased with the increasing of the activation temperature. Typical optimum value was shown by the sample activated at 900 °C with the specific capacitance was as high as 33.74 F g⁻¹ (scan rate 1 mV s⁻¹). The retained ratio was as high as 32.72%. The activated carbon pellet prepared from the rubber wood sawdust may found used in supercapacitor applications.     

Structural and electrical properties of ZnO-doped 8 mol% yttria-stabilized zirconia

8 mol% Yttria-stabilized zirconia (8YSZ) powder was prepared by coprecipitation. ZnO (0.5, 1.0, 2.0, 5.0, 10.0 wt.%) was added to the YSZ powder through a mechanical mixing method. The densification , microstructure and electrical properties of the YSZ ceramics sintered at 1300 °C for 2 h, were investigated. It was found that the small addition of ZnO was effective in reducing the sintering temperature and promoting the densification rate of the ceramics. The 5.0 wt.% ZnO-doped YSZ has ∼ 96% relative density, as compared to ∼ 89% relative density for the undoped sample. The total conductivity of 8YSZ was evidently increased by doping small amount of ZnO. For the 0.5 wt.% doped sample, the total conductivity of 2.89 × 10^− 2 Ω^− 1 cm^− 1 and an increase of 120% in conductivity were observed at 800 °C, as compared to that of the undoped one. We also found that the grain boundary (GB) conductivity could be improved by small addition of ZnO. At intermediate temperature (∼ 300 °C), the maximum enhancement of GB conductivity was observed with 5.0 wt% ZnO dopant. Finally, the volume percentage of GB in the ceramics was estimated by the brick layer model. The possible mechanism related to the improved GB conduction of the YSZ due to the ZnO additions was discussed.     

Visible,near-infrared and infrared optical properties of silica aerogels

Silica aerogel is an excellent thermal insulation material with a low thermal conductivity and a high porosity and has attracted great concern in applications. This paper was to experimentally investigate the optical properties of optically thick silica aerogel in the visible, near-infrared and infrared spectrum region. The fiber-loaded silica aerogel sample was prepared through sol–gel technique and supercritical drying process. Silica fibers were added into the aerogel during the preparation procedure to strength the skeleton of aerogel. As a comparison with the fiber-load silica aerogel, a silica fiber composite sample with the same chemical component and different physical structure was also prepared. A simplified two-flux model neglecting the boundary effect was used to describe the radiation propagation characteristics inside the samples. The spectral normal-hemispherical reflectances, transmittances, and normal emittances of silica aerogel and silica fiber samples were measured and compared in the wavelengths of 0.38–15 μm. Then the spectral optical constants of samples were determined using the experimental data. The spectral absorption and scattering coefficients of silica aerogel were within (0.01 cm⁻¹, 31.0 cm⁻¹) and (1.4 cm⁻¹, 25.8 cm⁻¹). The results showed that the spectrum region where the scattering coefficient is low usually corresponds to a high absorption coefficient. In addition, the total radiation properties of samples were predicted at high temperatures. The analysis of optical properties of silica aerogel is necessary to provide valuable data in applications.     

Lead free KNN/P(VDF-TrFE) 0–3 pyroelectric composite films and its infrared sensor

(K_0.5Na_0.5)NbO₃ (KNN)/[P(VDF-TrFE)70:30] composite thick films with different KNN weight ratios have been fabricated and the effect of KNN mass content on the material structure and properties have been studied in this paper. Properties of the infrared sensor based KNN/[P(VDF-TrFE)70:30] composite thick film were also systematically studied. It was found that the sample containing 30 wt.% KNN show optimal properties for pyroelectric appliance and the highest pyroelectric coefficient was 63 μCm⁻² K⁻¹. Infrared sensors using 30 wt.% KNN-70 wt.%[P(VDF-TrFE)70:30] show highest detectivity (D¹ = 3.21 × 10⁸ cm Hz^1/2 W⁻¹) at 137.3 Hz, indicating it is an promising candidate in lead-free quick response infrared detectors.     

Kinetic studies of electronically conducting Yb3Al5O12 garnet

Upon reduction, originally fully transparent and insulating ytterbium alumina garnet single crystals, Yb₃Al₅O₁₂, become deeply colored and electrically conducting with a conductivity of the order of 10^− 3 Ω^− 1 cm^− 1 in the temperature range of 550 °C to 1000 °C. The redox kinetics of the material is studied by means of conductivity relaxation experiments performed at oxidising and reducing conditions. Good agreement is obtained with an optical study into the redox kinetics of Yb₃Al₅O₁₂.     

Electrochemical characterization on layered lithium ruthenate for electrochemical supercapacitors

Electrochemical characteristics of lithium ruthenate (Li_xRuO_2+0.5x·nH₂O) for electrochemical capacitors' electrode material were first examined in this paper by cyclic voltammetry, electrochemical impedance spectroscopy and galvanostatic charge–discharge tests. Results show that Li_xRuO_2+0.5x·nH₂O has electrochemical capacitive characteristic within the potential range of − 0.2–0.9 V (vs. SCE) in 1 M Li₂SO₄ solution. The capacitance mainly arises from pseudo-capacitance caused by lithium ions' insertion/extraction into/out of the Li_xRuO_2+0.5x·nH₂O electrode. The specific capacitance of 391 F g^− 1 can be delivered at 1 mA charge–discharge current for Li_xRuO_2+0.5x·nH₂O electrode with an energy density of 65.7 W h kg^− 1. This material also exhibits an excellent cycling performance and there is no attenuation of capacitance over 600 cycles.     

Rapid synthesis of LiCr0.15Mn1.85O4 by glycine–nitrate method

LiCr_0.15Mn_1.85O₄ spinel has been successfully synthesized by glycine–nitrate method (GNM). The presence of pure spinel phase was confirmed by long term XRPD measurements and the Rietveld structural refinement. Lattice parameter was estimated to be 8.2338 Å. Average particle size of prepared powder material is below 500 nm. The BET surface area is 9.6 m² g^− 1. As a cathode material for lithium batteries LiCr_0.15Mn_1.85O₄ shows initial discharge capacity of 110 mA h g^− 1 and capacity retention of 83% after 50 cycles.     

Lithium ion conducting PVA:PVdF polymer electrolytes doped with nano SiO2 and TiO2 filler

The effect of nano SiO₂ and TiO₂ fillers on the thermal, mechanical and electrochemical properties of PVA:PVdF:LiCF₃SO₃ have been investigated by three optimized systems of SPE (80PVA:20PVdF:15LiCF₃SO₃), CPE-I (SPE:8SiO₂) and CPE-II (SPE:4TiO₂). From the TGA curve least weight loss has been observed for CPE-II indicating high thermal stability compared to other systems. Stress–strain curve of the prepared samples confirm the enhancement of tensile strength in CPE-II compared to CPE-I and SPE. Conductivity studies show that addition of TiO₂ filler slightly enhances ionic conductivity 3.7×10⁻³ S cm⁻¹ compared to filler free system at 303 K. Dielectric plots have been analyzed and CPE-II possesses higher dielectric constant compared to CPE-I and filler free system. Temperature dependence of modulus plots has been studied for highest conductivity possessing sample. Wider electrochemical stability has been obtained for nano-composite polymer electrolytes. The results conclude that the prepared CPE-II shows the best performance and it will be well suited for lithium ion batteries.     

M/Li+(M = Mg2+, Zn2+, and Mn2+) ion-exchange on lithium ion-conducting perovskite-type oxides and their properties

Lithium ions of perovskite-type lithium ion conductor La_0.55Li_0.35TiO₃ were replaced by divalent Mg²⁺, Zn²⁺, and Mn²⁺ ions in an ion-exchange reaction using molten chlorides. The polycrystalline Mg-exchanged and Zn-exchanged samples are solid electrolytes for divalent Mg²⁺ and Zn²⁺ ions, whose dc ionic conductivities (σ = 2.0 × 10^− 6 S cm^− 1 at 558 K for the Mg-exchanged sample, La_0.56(2)Li_0.02(1)Mg_0.16(1)TiO_3.01(2) and σ = 1.7 × 10^− 6 S cm^− 1 at 708 K for the Zn-exchanged samples, La_0.55(1)Li_0.0037(2)Zn_0.15(1)TiO_2.98(2)) were compared to those of the known highest Mg²⁺ and Zn²⁺ inorganic solid electrolytes. The Mn-exchanged sample, then, showed paramagnetic behavior in the temperature range of 2 to 300 K. The Mn ions in the exchanged sample are divalent and the spin configuration is in high spin state (S = 5/2).     

Anomalous conductivity and microstructure in gadolinium doped ceria prepared from nano-sized powder

The temperature and the oxygen partial pressure dependences of the electron and hole conductivities were measured by the dc polarization method using a Hebb–Wagner's ion blocking cell for Gd_0.2Ce_0.8O_1.9 polycrystalline bodies with grain size of 0.5 μm prepared by sintering of nano-sized powder. A significant enrichment of gadolinium was observed in the vicinity of the grain boundary by TEM/EDS analyses. The electron conductivity were comparable with those of conventional Gd_0.2Ce_0.8O_1.9 polycrystalline body with grain size of 2 μm, and it followed p(O₂)^− 1/4 dependence at temperatures T = 973–1273 K. However, the observed hole conductivity was higher than that of conventional Gd_0.2Ce_0.8O_1.9, and it did not follow p(O₂)^1/4 dependence. This anomalous p(O₂) dependence disappeared after the sample was treated at T = 1773 K for 38 h and grain size was enlarged to 2–10 μm.