Observation of giant dielectric constant in CdCu3Ti4O12 ceramics

Although CdCu₃Ti₄O₁₂ is isostructural to CaCu₃Ti₄O₁₂, the room temperature low-frequency dielectric constant of the former compound was reported to be ∼400, only 1/25 of that of the latter material [M.A. Subramanian, et al., J. Solid State Chem. 151 (2000) 323]. In this communication, we report that the dielectric constant of CdCu₃Ti₄O₁₂ can be remarkably increased by elevating the sintering temperature. The room temperature dielectric constant at 100 kHz achieves 9000, almost as much as that of CaCu₃Ti₄O₁₂, for the sample sintered at 1283 K. The appearance of giant dielectric constant in CdCu₃Ti₄O₁₂ is explained in terms of internal barrier layer capacitance (IBLC) effect with the subgrain boundary as the barrier. Our result supplies an approach in searching for new giant-dielectric-constant materials in the CaCu₃Ti₄O₁₂ family.     

Ti deficiency effect on the dielectric response of CaCu3Ti4O12 ceramics

Single phase ceramics CaCu₃Ti_4.0O₁₂ and CaCu₃Ti_3.9O₁₂ have been prepared using the traditional solid-state reaction method. Compared with the stoichiometric ceramics CaCu₃Ti_4.0O₁₂, Ti-deficient ceramics CaCu₃Ti_3.9O₁₂ have the larger lattice parameter, the higher force constant, and smaller dielectric constant and the lower dissipation factor, although their fundamental characters of dielectric response are similar. Their characteristic relaxation frequencies are not well fitted with the Arrhenius Law but a tentatively supposed relation. With the Cole-Cole Law, the fitted broadened factors of dissipation peaks are 0.5433 and 0.8651 for CaCu₃Ti_3.9O₁₂ and CaCu₃Ti_4.0O₁₂, respectively. All facts mentioned above imply that mutually correlated motion of Ti ions or defects may be expected to be responsible for the giant dielectric constant and high dissipation factor of CaCu₃Ti_4.0O₁₂.     

Effect of Cu-stoichiometry on the dielectric and electric properties in CaCu3Ti4O12 ceramics

CaCu_3+yTi₄O₁₂ (y=0, ±0.025, ±0.05, ±0.1 and −0.15) ceramics are prepared by the conventional solid-state reaction technique under sintering condition of 1050 ^°C, 10 h. X-ray diffraction shows that they all have the good crystalline structure. Cu-deficient ceramics exhibit the microstructures of uniform grain size distribution, whereas both Cu-stoichiometric and Cu-rich ceramics display microstructures of bimodal grain size distribution. The largeness of low-frequency dielectric permittivity at room temperature is found to be very sensitive to the Cu-stoichiometry. Upon raising the measuring temperature, all of the ceramics present commonly three semicircles in the complex impedance plane. It indicates that there exist three distinct contributions, which are ascribed to arising from domains, grain boundaries and domain boundaries. In addition, the influence of CuO segregation on the dielectric and electrical properties is also discussed.     

Influence of sintering conditions and doping on the dielectric relaxation originating from the surface layer effects in CaCu3Ti4O12 ceramics

Detailed investigations into the dielectric dispersion phenomenon in the giant dielectric constant material CaCu₃Ti₄O₁₂ (CCTO) around room temperature revealed the existence of two successive dielectric relaxations. In the temperature domain, a new dielectric relaxation was clearly observed around 250 K, in addition to the well-investigated dielectric relaxation close to 100 K. The effect of sintering and doping (La³⁺) on the strength of these dielectric relaxations were studied in detail. The sintering temperature as well as its duration was found to have tremendous influence on the dielectric relaxation that was encountered around 250 K. This Maxwell-Wagner (M-W) type of relaxation was found to be originating from the surface layer containing the Cu-rich phase, which was ascribed to the difference in the oxygen content between the surface and the interior of the sample. Interestingly, this particular additional relaxation was not observed in La_2/3Cu₃Ti₄O₁₂, a low dielectric constant member of the CCTO family, in which the segregation of Cu-rich phase on the surface was absent. Indeed the correlation between the new relaxation and the presence of Cu-rich phase in CCTO ceramics was further corroborated by the absence of the same after removing the top and bottom layers.     

Low-temperature sintering and microwave dielectric properties of Ca2Zn4Ti15O36 ceramics

The sintering behavior, microstructures, and microwave dielectric properties of Ca₂Zn₄Ti₁₅O₃₆ ceramics with B₂O₃ addition were investigated. The crystalline phases and microstructures of Ca₂Zn₄Ti₁₅O₃₆ ceramics with 0-10 wt% B₂O₃ addition were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS). The sintering temperature of Ca₂Zn₄Ti₁₅O₃₆ ceramic was lowered from 1170 to 930 °C by 10 wt% B₂O₃ addition. Ca₂Zn₄Ti₁₅O₃₆ ceramics with 8 wt% B₂O₃ addition sintered at 990 °C for 2 h exhibited good microwave dielectric properties, i.e., a quality factor (Qf) 11,400 GHz, a relative dielectric constant (ε_r) 41.5, and a temperature coefficient of resonant frequency (τ_f) 94.4 ppm/°C.     

Oxygen-defects-related dielectric response in CaCu3Ti4O12 ceramics

A 10 mm thickness columned CaCu₃Ti₄O₁₂ ceramic was fabricated by the conventional solid-state reaction method and the dielectric properties of different parts in ceramic had been investigated. For the sample close to the surface, only one Debye-type relaxation around 10⁷ Hz was observed at room temperature. However, for the sample close to the core, another relaxation peak was observed at about 10⁴ Hz. The results were explained in terms of the equivalent circuit model by showing in the impedance spectroscopy. Moreover, it was introduced that the low-frequency dielectric relaxation is associated with the electrode-sample contact effect based on varying sample thickness and an annealing treatment in the nitrogen atmospheres.     

Reduced dielectric loss and leakage current in CaCu3Ti4O12/SiO2/CaCu3Ti4O12 multilayered films

The CaCu₃Ti₄O₁₂/SiO₂/CaCu₃Ti₄O₁₂ (CCTO/SiO₂/CCTO) multilayered films were prepared on Pt/Ti/SiO₂/Si substrates by pulsed laser deposition method. It has been demonstrated that the dielectric loss and the leakage current density were significantly reduced with the increase of the SiO₂ layer thickness, accompanied with a decrease of the dielectric constant. The CCTO film with a 20 nm SiO₂ layer showed a dielectric loss of 0.065 at 100 kHz and the leakage current density of 6×10⁻⁷ A/cm² at 100 kV/cm, which were much lower than those of the single layer CCTO films. The improvement of the electric properties is ascribed to two reasons: one is the improved crystallinity; the other is the reduced free carriers in the multilayered films.     

Enhanced giant dielectric response in Mg-substituted CaCu3Ti4O12 ceramics

Effects of Mg-substitution on the giant dielectric response in CaCu₃Ti₄O₁₂ ceramics were investigated and discussed. A significantly enhanced giant dielectric response was obtained in Ca(Cu_1?xMg_x)₃Ti₄O₁₂ ceramics, and the dielectric constant step increased with increasing Mg-substitution content. The results of X-ray photoelectron analysis confirmed the obvious increase of Ti³⁺/Ti⁴⁺ ratio, and the enhanced giant dielectric response should originate from the corresponding modification of the mixed-valent structure. The present results have great scientific significance in deepening the understanding on the origin of giant dielectric response and modulating the giant dielectric constant step in CaCu₃Ti₄O₁₂.     

Nanocrystalline CaCu<Subscript>3</Subscript>Ti<Subscript>4</Subscript>O<Subscript>12</Subscript> powder by PVA sol–gel route: synthesis,characterization and its giant dielectric constant

Nanocrystalline CaCu₃Ti₄O₁₂ powders were synthesized by a simple PVA sol–gel route and calcined at 700 and 800°C in air for 8 h. The diameter of the powders ranges from 40–100 nm. The calcined CaCu₃Ti₄O₁₂ powders were characterized by TG-DTA, XRD, FTIR, SEM, and TEM. Sintering of the powders was conducted in air at 1100°C for 16 h. The XRD results indicated that all sintered samples had a typical perovskite CaCu₃Ti₄O₁₂ structure although the sintered samples contained some amount of CaTiO₃. SEM of the sintered CaCu₃Ti₄O₁₂ ceramics showed the average grain sizes of 13–15 μm. The samples exhibit a giant dielectric constant, ε′∼10⁵ at 150 to 200°C with weak temperature dependence below 1 kHz in the sample sintered using the powders calcined at 700°C. The Maxwell–Wagner polarization mechanism is used to explain the high permittivity in these ceramics. It is also found that all sintered samples have the same activation energy of grains, which is ∼0.122 eV.     

Nanoparticles of the giant dielectric material, CaCu3Ti4O12 from a precursor route

A method of preparing the nanoparticles of CaCu₃Ti₄O₁₂ (CCTO) with the crystallite size varying from 30 to 200 nm is optimized at a temperature as low as 680 °C from the exothermic thermal decomposition of an oxalate precursor, CaCu₃(TiO)₄(C₂O₄)₈·9H₂O. The phase singularity of the complex oxalate precursor is confirmed by the wet chemical analyses, X-ray diffraction, FT-IR and TGA/DTA analyses. The UV-vis reflectance and ESR spectra of CCTO powders indicate that the Cu(II) coordination changes from distorted octahedra to nearly flattened tetrahedra (squashed) to square-planar geometry with increasing annealing temperature. The HRTEM images have revealed that the evolution of the microstructure in nanoscale is related to the change in Cu(II) coordination around the surface regions for the chemically prepared powder specimens. The nearly flattened tetrahedral geometry prevails for CuO₄ in the near surface regions of the particles, whereas square-planar CuO₄ groups are dominant in the interior regions of the nanoparticles. The powders derived from the oxalate precursor have excellent sinterability, resulting in high-density ceramics which exhibited giant dielectric constants upto 40,000 (1 kHz) at 25 °C, accompanied by low dielectric loss <0.07.     

Experimental and numerical investigation of a ceramic dielectric resonator (DRA): CaCu3Ti4O12 (CCTO)

In this study, the CaCu₃Ti₄O₁₂ (CCTO) ceramic phase was synthesized by microwave heating in a much shorter time compared to the conventional heating methods. The results indicate that microwave processing is a promising method for preparing CCTO ceramics. CCTO was prepared using a domestic microwave oven operated at 2.45 GHz with 800 W. After a few minutes of microwave irradiation the formation of CCTO was confirmed by X-ray powder diffraction. The CCTO ceramic was studied in the medium-frequency (MF) range (100 Hz-1 MHz) and in the microwave range of frequencies. The experimental and theoretical characteristics of the dielectric resonator antenna are investigated.     

Dielectric properties of lanthanum-doped CaCu3Ti4O12 synthesized by semi-wet route

Effect of La³⁺ doping at Ca²⁺ site in CaCu₃Ti₄O₁₂ has been examined. Compositions with x=0.10, 0.20 and 0.30 were synthesized in the system Ca_(1−3x/2)La_xCu₃Ti₄O₁₂ by semi-wet method. Powder X-ray diffraction confirmed the formation of monophasic compounds. The structure remains cubic similar to CaCu₃Ti₄O₁₂. Lattice parameter increases slightly with increasing La³⁺ concentration. Microstructure has been studied using scanning electron microscopy (SEM). Average grain size is in the range 2-4 μm for various compositions. Energy-dispersive spectrometer (EDS) studies confirm the stoichiometry of the synthesized materials. Dielectric constant, dielectric loss and conductivity of the samples decrease with increasing lanthanum concentrations.     

Compression of CdCu3Ti4O12 perovskite to 55 GPa

Synchrotron x-ray diffraction measurements of CdCu₃Ti₄O₁₂ (CDCTO) were performed up to 55.5 GPa. There is no structural phase transformation in this pressure range. The irregular curvature shifts of the P-V curve are attributed to the grain surface effect. Analysis indicates that the grain surface of CDCTO is stiffer than the grain interior at higher pressures. We point out that the atoms on grain surfaces must be either densely packed or have a strong correlation with the gain interior in order to have a high dielectric constant, as in CaCu₃Ti₄O₁₂. The derived bulk modulus of CDCTO is approximately 235±7 GPa with K^′=5.1±0.4.     

Low temperature fired Ni-Cu-Zn ferrite with Bi4Ti3O12

The Ni-Cu-Zn ferrites with different contents of Bi₄Ti₃O₁₂ ceramics (1-8 wt%) as sintering additives were prepared by the usual ceramic technology and sintered at 900 °C to adapt to the low temperature co-fired ceramic (LTCC) technology. The magnetic and dielectric properties of the ferrite can be effectively improved with the effect of an appropriate amount of Bi₄Ti₃O₁₂. For all samples, the ferrite sintered with 2 wt% Bi₄Ti₃O₁₂ has relatively high density (98.8%) and permeability, while the ferrite with 8 wt% Bi₄Ti₃O₁₂ has relatively good dielectric properties in a wide frequency range. The influences of Bi₄Ti₃O₁₂ addition on microstructure, magnetic and dielectric properties of the ferrite have been discussed.     

First principles study of the electron structures of CaCu3Mn4O12 and CaCu3Ti4O12

The electronic structures of CaCu₃Mn₄O₁₂ and CaCu₃Ti₄O₁₂ are investigated from HF SCF LCAO calculation. In CaCu₃Mn₄O_12, the band and the density of states show a spin asymmetric ferrimagnetic character with a small energy gap. The Mn spin is anti-aligned with the Cu spin, and the total spin moment is 9 μ_B. Our calculation correctly reproduces the observed antiferromagnetic insulating character of CaCu₃Ti₄O₁₂. The gap in the band structure, which is 2.15 eV, reasonably agrees with the experimental value 1.5 eV. The electron density populations at different planes show clearly that the electron density has symmetric character. A tilted Mn(Ti) orbital implies a typical tilted three-dimensional network of MnO₆ (TiO₆) octahedra due to doping of the Jahn–Teller ion Cu. There is no covalency between Ca, Cu and Mn(Ti) atoms. In contrast, there are stronger bonds and somewhat likely covalency between Cu and O atoms, and also between Mn(Ti) and O atoms.     

Electrical behavior of BaZr0.1Ti0.9O3 and BaZr0.2Ti0.8O3 thin films

BaZr_0.1Ti_0.9O₃ and BaZr_0.2Ti_0.8O₃ (BZT) thin films were deposited on Pt/Ti/LaAlO₃ (1 0 0) substrates by radio-frequency magnetron sputtering, respectively. The films were further annealed at 800 °C for 30 min in oxygen. X-ray diffraction θ-2θ and Φ-scans showed that BaZr_0.1Ti_0.9O₃ films displayed a highly (h 0 0) preferred orientation and a good cube-on-cube epitaxial growth on the LaAlO₃ (1 0 0) substrate, while there are no obvious preferential orientation in BaZr_0.2Ti_0.8O₃ thin films. The BaZr_0.1Ti_0.9O₃ films possess larger grain size, higher dielectric constant, larger tunability, larger remanent polarization and coercive electric field than that of BaZr_0.2Ti_0.8O₃ films. Whereas, BaZr_0.1Ti_0.9O₃ films have larger dielectric losses and leakage current density. The results suggest that Zr⁴⁺ ion can decrease dielectric constant and restrain non-linearity. Moreover, the enhancement in dielectric properties of BaZr_0.1Ti_0.9O₃ films may be attributed to (1 0 0) preferred orientation.     

Bismuth zinc niobate (Bi1.5ZnNb1.5O7) ceramics derived from metallo-organic decomposition precursor solution

The preparation, microstructure development and dielectric properties of Bi_1.5ZnNb_1.5O₇ pyrochlore ceramics by metallo-organic decomposition (MOD) route are reported. Homogeneous precalcined ceramic powders of 13-36 nm crystallite size were obtained at temperatures ranging from 500 to 700 °C. The thermal decomposition/oxidation of the gelled precursor solution was chemically analyzed, TG/DTA, XRD, and SEM, led to the formation of a pure cubic pyrochlore phase with a stoichiometry close to Bi_1.5ZnNb_1.5O₇ which begins to form at 500 °C. The metallo-organic precursor synthesis method, where Bi, Zn and Nb ions are chelated to form metal complexes, allows the control of Bi/Zn/Nb stoichiometric ratio on a molecular scale leading to the rapid formation of bismuth zinc niobate (Bi_1.5ZnNb_1.5O₇) ceramic fine powders with pure pyrochlore structure. The powders were pressed into pellets and can be sintered at temperatures as low as 800-1000 °C. Fine crystalline ceramics with the grain size in the range of 200-500 nm have been obtained at the sintering temperature of 800 °C. The dielectric properties in high frequency to microwave range were measured and discussed.     

Fe掺杂CaCu3Ti4O12陶瓷的介电性能与弛豫特性研究

采用固相反应法制备了CaCu₃Ti_4-xFe_xO₁₂(0≤x≤0.2)陶瓷,通过X射线衍射、扫描电子显微镜、介电频谱和阻抗谱等手段研究了Fe对CaCu₃Ti₄O₁₂陶瓷的结构和介电性能的影响.研究发现：CaCu₃Ti_4-xFe_{x关键词： 巨介电常数 双阻挡层电容模型 界面极化}     

Ferroelectric-relaxor behavior of (Na0.5K0.5)NbO3-based ceramics

We report that ferroelectric-relaxor behavior is induced by doping of SrO and TiO₂, or BaO and TiO₂ into classic ferroelectric (Na_0.5K_0.5)NbO₃. It is found that [(Na_0.5K_0.5)_0.9Sr_0.1](Nb_0.9Ti_0.1)O₃ ceramics exhibit a pronounced ferroelectric-relaxor behavior, comparable to that of [(Na_0.5K_0.5)_0.9Ba_0.1](Nb_0.9Ti_0.1)O₃ ceramics. Our results indicate that the relaxor behavior is closely related to the appearance of micropolar regions in these systems. The relaxor behavior should arise from the dynamic response of micropolar clusters. Raman spectra of [(Na_0.5K_0.5)_1−xSr_x](Nb_1−xTi_x)O₃ ceramics measured in the wavenumber range from 100 to 1200 cm⁻¹ confirm that the first order scattering is dominant in phonon bands should result from both short-range ordered region (micropolar regions) and disordered matrix. The frequency dependence of dielectric permittivity measurements show that the relaxor behavior of SrO and TiO₂, or BaO and TiO₂ doped (Na_0.5K_0.5)NbO₃ ceramics is not a Debye type in the radio frequency range.     

Influence of Lu2O3 on electrical and microstructural properties of CaCu3Ti4O12 ceramics

In this work, the influence of Lu₂O₃ doped on the dielectric and electrical properties of CaCu₃Ti₄O₁₂ was reported. Lu₂O₃-doped CCTO was prepared by a conventional solid state technique using CuO, TiO₂, and CaCO₃ as starting materials. The samples were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM); dielectric measurements were measured in the 10² Hz–10⁷ Hz frequency range at room temperature; and the nonlinear behavior of all samples was measured. The doping of Lu₂O₃ resulted in an increase in the dielectric constant of CCTO, but decreased the stability of the frequency dependence. Increasing concentrations of Lu₂O₃ resulted in decreasing nonlinear coefficients.