Simplified method to prepare atomically-ordered TiO2(1 1 0)-(1 × 1) surfaces with steps and terraces

An effective way to prepare atomically-ordered rutile TiO₂(1 1 0) surfaces that have distinct step and terrace structures suitable for oxide thin film deposition is demonstrated. Only a two-step procedure, consisting of 20% HF etching and UHV-annealing at 1100 °C, was required to yield a clean (1 × 1) structure with step and terrace structures. Investigation of the surface using scanning tunneling microscopy, low-energy electron diffraction, and Auger electron spectroscopy reveals that carbon contamination is removed at around 800 °C, and straight steps with clear terraces appear at around 1000 °C.     

RHEED studies during growth of TiN/SiNx/TiN trilayers on MgO(0 0 1)

TiN/SiN_x/TiN(0 0 1) trilayers have been deposited on MgO(0 0 1) substrates using ultra-high vacuum based reactive magnetron sputtering and studied by in situ reflection high energy electron diffraction (RHEED). Depositions were carried out at 500 °C and 800 °C, with SiN_x layer thicknesses between 3 and 300 Å. Here, we find that SiN_x(0 0 1) layers grown at 800 °C exhibit 1 × 4 surface reconstructions along orthogonal 〈1 1 0〉 directions up to a critical thickness of ∼9 Å, where an amorphous phase forms. Growth of TiN overlayers on the reconstructed SiN_x(0 0 1) layers yield RHEED patterns indicating the growth of (0 0 1)-oriented epitaxial layers with a 1 × 1 reconstruction. For the case of amorphous SiN_x layers the TiN overlayers grow polycrystalline.     

Characterization of bicrystalline epitaxial LaNiO3 films fabricated on MgO (1 0 0) substrates by pulsed laser deposition

A series of metallic LaNiO₃ (LNO) thin films were deposited on MgO (1 0 0) substrates by pulsed laser deposition (PLD) under the oxygen pressure of 20 Pa at different substrate temperatures from 450 to 750 °C. X-ray diffraction (XRD) was used to characterize the crystal structure of LNO films. θ-2θ scans of XRD indicate that LNO film deposited at a substrate temperature of 700 °C has a high orientation of (l l 0). At other substrate temperatures, the LNO films have mixed phases of (l l 0) and (l 0 0). Furthermore, pole figure measurements show that LNO thin films, with the bicrystalline structure, were epitaxially deposited on MgO (1 0 0) substrates in the mode of LNO (1 1 0)//MgO (1 0 0) at 700 °C. Reflection high-energy electric diffraction (RHEED) and atomic force microscopy (AFM) were also performed to investigate the microstructure of LNO films with the high (l l 0) orientation. RHEED patterns clearly confirm this epitaxial relationship. An atomically smooth surface of LNO films at 700 °C was obtained. In addition, bicrystalline epitaxial LNO films, fabricated at 700 °C, present a excellent conductivity with a lower electrical resistivity of 300 μ Ω cm. Thus, the obtained results indicate that bicystalline epitaxial LNO films could serve as a promising candidate of electrode materials for the fabrication of ferroelectric or dielectric films.     

The preparation of c-axis epitaxial Bi-2212 films on STO(1 0 0) by sol-gel method

Bi₂Sr₂Ca₁Cu₂O_8+δ (Bi-2212) films were grown on (1 0 0) oriented SrTiO₃ (STO) substrate using sol-gel spin-coating method. The effects of heat treatment conditions and coating times on the phase formation and surface morphology were investigated using thermal analysis, optical microscope, X-ray diffraction, and scanning electronic microscopy. Mixed phases were formed from 820 to 840 °C, and Bi-2212 single phase was obtained at 830 °C for 3 h. c-axis epitaxial films with smooth surfaces were obtained by drying at 600 °C and coating for 5 times.     

Characterization of single-crystalline In2O3 films deposited on Y-stabilized ZrO2 (1 0 0) substrates by MOCVD

Epitaxial In₂O₃ films have been deposited on Y-stabilized ZrO₂ (YSZ) (1 0 0) substrates by metalorganic chemical vapor deposition (MOCVD). The films were deposited at different substrate temperatures (450-750 °C). The film deposited at 650 °C has the best crystalline quality, and observation of the interface area shows a clear cube-on-cube epitaxial relationship of In₂O₃(1 0 0)||YSZ(1 0 0) with In₂O₃[0 0 1]||YSZ[0 0 1]. The Hall mobility of the single-crystalline In₂O₃ film deposited at 650 °C is as high as 66.5 cm² V⁻¹ s⁻¹ with carrier concentration of 1.5 × 10¹⁹ cm⁻³ and resistivity of 6.3 × 10⁻³ Ω cm. The absolute average transmittance of the obtained films in the visible range exceeds 95%.     

The investigation of room temperature ferromagnetism in (1 0 0) oriented BaNb2O6 PLD films on LaAlO3 (1 0 0) substrate

(1 0 0) oriented BaNb₂O₆ films have been successfully grown on LaAlO₃ (1 0 0) substrate at 750 °C or 450 °C in vacuum by pulsed laser deposition. The deposited BaNb₂O₆ PLD films exhibit room-temperature ferromagnetism. Ab initio calculations demonstrate that stoichiometric BaNb₂O₆ and that with barium vacancy are nonmagnetic, while oxygen and niobium vacancy can induce magnetism due to the spin-polarization of Nb s electrons and O p electrons respectively. Moreover, ferromagnetic coupling is energetically more favorable when two Nb/O vacancies are located third-nearest-neighbored. The observed room temperature ferromagnetism in BaNb₂O₆ films should be mainly induced by oxygen vacancies introduced during vacuum deposition, with certain contribution by Nb vacancies.     

Epitaxial MoOx nanostructures on TiO2(1 1 0) obtained using thermal decomposition of Mo(CO)6

Stoichiometric and highly-defective TiO₂(1 1 0) surfaces (called as yellow and blue, respectively) were exposed to Mo(CO)₆ vapours in UHV and in a reactive O₂ atmosphere. In the case of yellow-TiO₂, an O₂ reactive atmosphere was necessary to obtain the Mo(CO)₆ decomposition at 450 °C with deposition of MoO_x nanostructures where, according to core level photoemission data, the Mo⁺⁴ state is predominant. In the case of blue-TiO₂ it was possible to obtain Mo deposition both in UHV and in an O₂ atmosphere. A high dose of Mo(CO)₆ in UHV on blue-TiO₂ allowed the deposition of a thick metallic Mo layer. An air treatment of this sample at 580 °C led to the elimination of Mo as MoO₃ and to the formation of a transformed layer of stoichiometry of Ti_(1−x)Mo_xO₂ (where x is close to 0.1) which, according to photoelectron diffraction data, can be described as a substitutional near-surface alloy, where Mo⁺⁴ ions are embedded into the titania lattice. This embedding procedure results in a stabilization of the Mo⁺⁴ ions, which are capable to survive to air exposure for a rather long period of time. After exposure of the blue-TiO₂(1 1 0) substrate to Mo(CO)₆ vapours at 450 °C in an O₂ atmosphere it was possible to obtain a MoO₂ epitaxial ultrathin layer, whose photoelectron diffraction data demonstrate that is pseudomorphic to the substrate.     

Ultrathin ZrO2 films on Si-rich SiC(0 0 0 1)-(3 × 3): Growth and thermal stability

The growth and thermal stability of ultrathin ZrO₂ films on the Si-rich SiC(0 0 0 1)-(3 × 3) surface have been explored using photoelectron spectroscopy (PES) and X-ray absorption spectroscopy (XAS). The films were grown in situ by chemical vapor deposition using the zirconium tetra tert-butoxide (ZTB) precursor. The O 1s XAS results show that growth at 400 °C yields tetragonal ZrO₂. An interface is formed between the ZrO₂ film and the SiC substrate. The interface contains Si in several chemically different states. This gives evidence for an interface that is much more complex than that formed upon oxidation with O₂. Si in a 4+ oxidation state is detected in the near surface region. This shows that intermixing of SiO₂ and ZrO₂ occurs, possibly under the formation of silicate. The alignment of the ZrO₂ and SiC band edges is discussed based on core level and valence PES spectra. Subsequent annealing of a deposited film was performed in order to study the thermal stability of the system. Annealing to 800 °C does not lead to decomposition of the tetragonal ZrO₂ (t-ZrO₂) but changes are observed within the interface region. After annealing to 1000 °C a laterally heterogeneous layer has formed. The decomposition of the film leads to regions with t-ZrO₂ remnants, metallic Zr silicide and Si aggregates.     

Oxidation and thermal reduction of the Cu(1 0 0) surface as studied using positron annihilation induced Auger electron spectroscopy (PAES)

Changes in the surface of an oxidized Cu(1 0 0) single crystal resulting from vacuum annealing have been investigated using positron annihilation induced Auger electron spectroscopy (PAES). PAES measurements show a large increase in the intensity of the annihilation induced Cu M_2,3VV Auger peak as the sample is subjected to a series of isochronal anneals in vacuum up to annealing temperature 300 °C. The intensity then decreases monotonically as the annealing temperature is increased to ∼600 °C. Experimental probabilities of annihilation of surface-trapped positrons with Cu 3p and O 1s core-level electrons are estimated from the measured intensities of the positron annihilation induced Cu M_2,3VV and O KLL Auger transitions. Experimental PAES results are analyzed by performing calculations of positron surface states and annihilation probabilities of surface-trapped positrons with relevant core electrons taking into account the charge redistribution at the surface, surface reconstructions, and electron-positron correlations effects. The effects of oxygen adsorption on localization of positron surface state wave function and annihilation characteristics are also analyzed. Possible explanation is proposed for the observed behavior of the intensity of positron annihilation induced Cu M_2,3VV and O KLL Auger peaks and probabilities of annihilation of surface-trapped positrons with Cu 3p and O 1s core-level electrons with changes of the annealing temperature.     

CO2 adsorption on Cr(1 1 0) and Cr2O3(0 0 0 1)/Cr(1 1 0)

We attempt to correlate qualitatively the surface structure with the chemical activity for a metal surface, Cr(1 1 0), and one of its surface oxides, Cr₂O₃(0 0 0 1)/Cr(1 1 0). The kinetics and dynamics of CO₂ adsorption have been studied by low energy electron diffraction (LEED), Aug er electron spectroscopy (AES), and thermal desorption spectroscopy (TDS), as well as adsorption probability measurements conducted for impact energies of E_i = 0.1-1.1 eV and adsorption temperatures of T_s = 92-135 K. The Cr(1 1 0) surface is characterized by a square shaped LEED pattern, contamination free Cr AES, and a single dominant TDS peak (binding energy E_d = 33.3 kJ/mol, first order pre-exponential 1 × 10¹³ s⁻¹). The oxide exhibits a hexagonal shaped LEED pattern, Cr AES with an additional O-line, and two TDS peaks (E_d = 39.5 and 30.5 kJ/mol). The initial adsorption probability, S₀, is independent of T_s for both systems and decreases exponentially from 0.69 to 0.22 for Cr(1 1 0) with increasing E_i, with S₀ smaller by ∼0.15 for the surface oxide. The coverage dependence of the adsorption probability, S(Θ), at low E_i is approx. independent of coverage (Kisliuk-shape) and increases initially at large E_i with coverage (adsorbate-assisted adsorption). CO₂ physisorbs on both systems and the adsorption is non-activated and precursor mediated. Monte Carlo simulations (MCS) have been used to parameterize the beam scattering data. The coverage dependence of E_d has been obtained by means of a Redhead analysis of the TDS curves.     

Chemically prepared well-ordered InP(0 0 1) surfaces

In the present work HCl-isopropanol treated and vacuum annealed InP(0 0 1) surfaces were studied by means of low-energy electron diffraction (LEED), soft X-ray photoemission (SXPS), and reflectance anisotropy (RAS) spectroscopies. The treatment removes the natural oxide and leaves on the surface a physisorbed overlayer containing InCl_x and phosphorus. Annealing at 230 °C induces desorption of InCl_x overlayer and reveals a P-rich (2 × 1) surface. Subsequent annealing at higher temperature induces In-rich (2 × 4) surface. The structural properties of chemically prepared InP(0 0 1) surfaces were found to be similar to those obtained by decapping of As/P-capped epitaxial layers.     

Enhanced formation of periodic arrays of low-resistivity NiSi nanocontacts on (0 0 1)Si0.7Ge0.3 by nanosphere lithography with a thin interposing Si layer

In this study, we demonstrated significant enhancement of the formation of low-resistivity NiSi nanocontacts with controlled size on (0 0 1)Si_0.7Ge_0.3 substrates by combining the nanosphere lithography with the use of a new Ni/a-Si bilayer nanodot structure. Low-resistivity NiSi with an average size of 78 nm was observed to be the only silicide phase formed in samples annealed at 350-800 °C. The presence of the interposing Si layer with appropriate thickness was found to effectively prevent Ge segregation and maintain the interface stability in forming NiSi nanocontacts on (0 0 1)Si_0.7Ge_0.3. As the annealing temperature was increased to 900 °C, amorphous SiO_x nanowires were observed to grow from silicide nanocontact regions. The NSL technique in conjunction with a sacrificial Si interlayer process promises to be applicable in fabricating periodic arrays of other low-resistivity silicide nanocontacts on Si_1−xGe_x substrates without complex lithography.     

Observation of stable mixed alkanethiolate-chloride adlayer on Ag(1 1 1): structural correlation with pure alkanethiolate monolayers

The self-assembly of 1-alkanethiols, CH₃(CH₂)_n−1SH (n=2-16), on Ag(1 1 1) film initially covered with a native oxide monolayer and that on a chloride-covered Ag(1 1 1) were comparatively studied by X-ray photoelectron spectroscopy and scanning tunneling microscopy. The native oxide monolayer was readily substituted completely by thiolates irrespective of chain length, leading to a dense (√7×√7)R19.1° monolayer for n<3, or a distorted (√7×√7)R19.1° structure for n>3 accompanied by distinct island and fine domain structures previously reported by other groups. In contrast, the chloride-to-thiolate conversion was far from complete for long alkanethiols (n?8), and at sufficiently high conversion temperature (>50 °C), we found a highly stable mixed thiolate-chloride monolayer with a well-defined 2:1 S/Cl atomic ratio, suggesting the occurrence of a mixed (√7×√7)R19.1° adlayer ordering. The combined effects of substrate-molecule and intermolecular interactions behind these contrastive phenomena are discussed.     

Influence of substrate temperature in BiFeO3-CoFe2O4 nanocomposites deposited on SrTiO3 (0 0 1)

BiFeO₃-CoFe₂O₄ epitaxial nanocomposites have been deposited on SrTiO₃ (0 0 1) substrates by pulsed laser deposition. We present here a study of the influence of the deposition temperature (T_S), in the 550-800 °C range, on the film composition, morphology and microstructure. Electron-probe microanalysis shows strong reduction of the Bi content in the films when increasing T_S. Films prepared at T_S=750 °C and above are virtually Bi-free. X-ray diffraction (XRD) data show that, due to the volatility of Bi, there is a progressive reduction in the amount of BiFeO₃. The deposition temperature and the concomitant presence of Fe_xO_y spurious phases in the nanocomposites grown at high temperature promote radical changes in film morphology and magnetization. It thus follows that a temperature range suitable for controlled modification of nanocomposites morphology would be extremely narrow.     

L10 FePt thin films with [0 0 1] crystalline growth fabricated by SiO2 addition—rapid thermal annealing and dot patterning of the films

FePt films that have a high degree of order S in their L1₀ structure (S>0.90) and well-defined [0 0 1] crystalline growth perpendicular to the film plane were fabricated on thermally oxidized Si substrates by the addition of an oxide and successive rapid thermal annealing (RTA). The mechanism of L1₀ ordering and [0 0 1] crystalline growth perpendicular to the film plane arising through the oxide addition and RTA process is also discussed. The L1₀ ordering (S>0.90) and the [0 0 1] crystalline growth were achieved by (1) lowering the activation energy due to in-plane tensile stress and the initiation of L1₀ ordering at a low temperature, (2) [0 0 1] crystalline growth through in-plane tensile stress, and (3) enhancement of atomic diffusion via the addition of an oxide and the resultant lowering of the ordering temperature. Effect (1) was observed in the case of SiO₂ addition, effect (2) was generally observed in the case of oxide addition and the RTA process, and effect (3) was prominent in the case of ZnO addition. With the addition of ZnO, the L1₀ ordering started at below 400 °C and was completed at 500 °C. Finally, dot patterns were successfully fabricated down to a diameter of 15 nm using electron beam lithography, and the magnetic state of the dot pattern was observed by magnetic force microscopy.     

Conductivity and sintering property of LaNi1 − xFexO3 ceramics prepared by Pechini method

Preparation of LaNi_1 − xFe_xO₃, which is one of the candidate materials of solid oxide fuel cell cathode, current collecting layer and interconnect coating was examined with Pechini method and solid state reaction method. Single phase LaNi_1 − xFe_xO₃ with large Ni content has successfully been prepared by low temperature sintering as 750 °C with Pechini method, whereas large amount of raw materials has remained with solid state reaction method by sintering at the same temperature. It can be ascribed to more homogenous cation distribution in raw powder material prior to sintering with Pechini method. It has also been revealed that LaNi_1 − xFe_xO₃ with x lower than 0.3 is thermodynamically unstable in air above 1000 °C. LaNi_0.6Fe_0.4O₃ showed superior property as cathode material with high electrical conductivity, thermodynamic stability and appropriate sintering property.     

Selforganized nanopatterning of Si(0 0 1)

The (2 × n) superstructure of Si(0 0 1) consists of elongated (2 × 1) reconstructed stripes separated by a dimer-vacancy line every few nanometers, thus offering a means to obtain a nanopattered Si(0 0 1) surface. Scanning tunneling microscopy (STM) investigations of Si(0 0 1) substrates that were deoxidized at 880-920 °C reveal that the formation of the (2 × n) depends strongly on the Si coverage of the topmost surface layer. It forms only in a narrow coverage window ranging from 0.6 to 0.8 ML. Systematic Monte Carlo simulations by an algorithm that combines the diffusion of monomers and dimers with the simultaneous deposition of Si onto the Si(0 0 1) surface, corroborate the STM results and suggest Si deposition as a viable alternative for introducing dimer vacancies in a well-defined manner.     

Magneto-optical study of slanted Co nanowires embedded in CeO2/SrTiO3(0 0 1)

Sequential pulsed laser deposition of CoO and CeO₂ at 650 °C under vacuum leads to the formation of a slanted Co nanowires assembly embedded in CeO₂/SrTiO₃(0 0 1) epilayers. High temperature magneto-optical Faraday measurements were performed, which revealed a Faraday ellipticity of 1.3° at a wavelength of 450 nm for 300 nm thick samples and which allowed to access the magnetic properties. From the analysis of the coercivity dependence on temperature, it is shown that the magnetic anisotropy of the slanted Co nanowires is dominated by shape anisotropy and that their magnetization reversal is localized.     

Structure, dielectric and ferroelectric properties of highly (1 0 0)-oriented BaTiO3 grown under low-temperature conditions

The highly (1 0 0)-oriented BaTiO₃ thin films were fabricated on LaNiO₃(1 0 0)/Pt/Ti/SiO₂/Si substrates under low-temperature conditions. Substrate temperatures throughout the fabrication process remained at or below 400 °C, which allows this process to be compatible with many materials commonly used in integrated circuit manufacturing. X-ray diffraction data provided the evidence for single BaTiO₃ phase. Field-emission scanning electron microscopy was used to study the columnar structure of the films. The dielectric properties as a function of frequency in the range of 1 kHz to 1 MHz was obtained. The room temperature remanent polarization (2P_r) and coercive field were found to be ∼5 μC/cm² and 50 kV/cm, respectively. The BTO film maintains an excellent fatigue-free character even after 10⁹ switching cycles.     

High resolution analysis of the rotational levels of the (0 0 0), (0 1 0), (1 0 0), (0 0 1), (0 2 0), (1 1 0) and (0 1 1) vibrational states of SO2

A high resolution (0.0018 cm⁻¹) Fourier transform instrument has been used to record the spectrum of an enriched ³⁴S (95.3%) sample of sulfur dioxide. A thorough analysis of the ν₂, 2ν₂ − ν₂, ν₁, ν₁ + ν₂ − ν₂, ν₃, ν₂ + ν₃ − ν₂, ν₁ + ν₂ and ν₂ + ν₃ bands has been carried out leading to a large set of assigned lines. From these lines ground state combination differences were obtained and fit together with the existing microwave, millimeter, and terahertz rotational lines. An improved set of ground state rotational constants were obtained. Next, the upper state rotational levels were fit. For the (0 1 0), (1 1 0) and (0 1 1) states, a simple Watson-type Hamiltonian sufficed. However, it was necessary to include explicitly interacting terms in the Hamiltonian matrix in order to fit the rotational levels of the (0 2 0), (1 0 0) and (1 0 1) states to within their experimental accuracy. More explicitly, it was necessary to use a ΔK = 2 term to model the Fermi interaction between the (0 2 0) and (1 0 0) levels and a ΔK = 3 term to model the Coriolis interaction between the (1 0 0) and (0 0 1) levels. Precise Hamiltonian constants were derived for the (0 0 0), (0 1 0), (1 0 0), (0 0 1), (0 2 0), (1 1 0) and (0 1 1) vibrational states.