草莓型SiO2/PMMA纳米复合微球的制备

在纳米二氧化硅水分散体系中,借助于碱性辅助单体1-乙烯基咪唑(1-VID)与未改性纳米二氧化硅表面羟基之间的酸-碱作用,通过1-VID与甲基丙烯酸甲酯(MMA)的自由基共聚合,制备了草莓型的SiO2/PMMA复合微球.整个反应过程中,纳米二氧化硅无需表面处理,体系中无需另外加入乳化剂或助乳化剂,微球表面吸附的纳米二氧化硅对颗粒起稳定作用.用动态光散射粒度分布仪测得复合微球粒径在120-330nm之间,热重分析结果表明,复合微球中二氧化硅含量介于15%-20%之间.透射电镜和扫描电镜显示所得复合微球具有草莓型结构,二氧化硅富集在表面.     

不同酸对介孔二氧化硅球表面形貌和介相结构的影响

在室温、不同酸性条件下合成出微米级球形介孔二氧化硅材料，通过XRD、SEM以及氮气吸附等手段对介孔二氧化硅材料进行了表征。用TEM跟踪不同反应时间介孔二氧化硅球的形成，对这些球颗粒的合成机理进行了讨论，同时探讨了不同酸性条件下介孔二氧化硅表面形貌和介相结构的变化。     

草莓型PMMA/SiO_2有机-无机复合微球的合成与表征

在纳米二氧化硅水分散介质中,借助于正离子单体甲基丙烯酰氧乙基三甲基氯化铵(MTC)与未改性纳米二氧化硅颗粒之间的电荷作用,通过MTC与甲基丙烯酸甲酯(MMA)的自由基共聚合,制备了草莓型的PMMA/SiO2复合微球.整个制备反应过程中,纳米二氧化硅无需表面处理,体系中无需另外加入乳化剂或助乳化剂,微球表面吸附的纳米二氧化硅对颗粒起稳定作用.详细讨论了纳米二氧化硅初始添加量、MTC浓度对复合微球的平均粒径、复合微球中二氧化硅含量及微球形态的影响.动态光散射粒度分布仪(DLS)测得复合微球粒径在180~300 nm之间,热重分析(TGA)表明复合微球中二氧化硅含量介于16.4%~40.8%之间.透射电镜(TEM)显示所得复合微球具有草莓型结构,二氧化硅于表面富集.     

硬模板法高温水热合成微孔-介孔二氧化硅及掺铝介孔二氧化硅

摘要 采用高温水热合成的方法有利于得到具备高水热稳定性的介孔二氧化硅.本研究中,我们利用α-亚麻酸在加热条件下通过胶束内聚合转化为能够耐受高温水热环境的介观模板,利用此硬模板在高温水热条件下直接合成了微孔-介孔二氧化硅及掺铝介孔二氧化硅.采用了不同的表征手段如X射线衍射（XRD）,氮气吸附,透射电镜等手段对材料进行了表征. 实验结果表明,制得的材料在沸水中处理5天后,仍能保持670m2 g-1的比表面积.透射电镜结果和NLDFT孔径分析结果显示,材料同时具备介孔和微孔结构.29Si MAS NMR谱图显示,完全缩聚的Q4型硅为材料中主要的硅组分,这解释了材料的高水热稳定性.     

SiO2纳米粒子对溶胶凝胶涂层性能的影响

在高强钢表面制备了防护性溶胶凝胶涂层,并研究了不同浓度二氧化硅纳米粒子的加入对于涂层形貌、耐蚀性和硬度的影响。采用扫描电子显微镜(SEM)和电子能谱(EDS)观察了涂层的微观结构和成分;采用显微硬度计测试了涂层的硬度;采用电化学方法研究了二氧化硅纳米粒子的浓度对于涂层耐蚀性能的影响;采用傅里叶红外光谱研究涂层的化学结构,进而探讨了二氧化硅纳米粒子对于涂层的强化机理。结果显示涂层加入二氧化硅纳米粒子的最佳浓度为500 mg.L-1,此条件下的涂层表面均匀致密,有较高的硬度并且在3.5%NaCl溶液中体现出较好的耐蚀作用。纳米粒子在溶胶中反应形成活性羟基基团并与硅烷发生反应生成空间网状结构,从而强化涂层。     

二氧化硅填料与硅橡胶在热老化时的作用

本文研究了三种表面性质不同的二氧化硅填料与二甲基硅橡胶在热老化时的作用。使混炼胶和硫化胶分别在甲苯和甲苯-氨中溶胀,测定了结合胶及溶胀度的变化。证明在老化时填料和橡胶之间有数量可观的化学键生成,并且发生氢键向化学键的转化。填料表面经过化学处理或加结构化控制剂,对它和橡胶之间的氢键结合,化学反应均有一定的抑制作用。     

海泡石制备HMS和AlSBA介孔分子筛的研究

通过酸浸和模板合成处理，海泡石直接合成有序介孔二氧化硅和含铝的介孔二氧化硅. 海泡石用盐酸处理后120 ℃下在NaOH溶液中处理72 h, 得到具有HMS结构特征的介孔分子筛；在含铝的碱性溶液中处理后得到具有AlSBA结构的介孔分子筛. 并用SAXRD、BET、TPD表征了介孔分子筛的物相结构、比表面积、孔径分布和表面酸性. 两种介孔分子筛的比表面积分别为508 m2•g^-1和946 m2•g^-1，孔径分别为3.4 nm和3.9 nm，且孔径分布窄. NH3-TPD结果表明分子筛表面都有两个酸中心，随着Al原子的引入，表面酸性增强.     

以阴离子表面活性剂/阳离子聚铵复合胶束为模板合成有序介孔二氧化硅

基于静电作用, 阴离子表面活性剂可与阳离子聚铵组装形成复合胶束. 借助阳离子聚铵,复合胶束可以作为模板与硅源协同组装, 形成高度有序的介孔二氧化硅. 本文通过调变不同种类阴离子表面活性剂、合成体系pH值、合成温度及阳离子聚铵和硅源用量等因素, 合成了具有不同介观结构和形貌的介孔二氧化硅. 实验证实阴离子表面活性剂/阳离子聚铵复合胶束模板法是合成介孔二氧化硅的一种通用方法.     

利用廉价硅酸盐为硅源合成介孔SiO2球

利用廉价的硅酸盐为二氧化硅前驱体,以非离子和阳离子表面活性剂为混合模板剂合成微米级的介孔二氧化硅。控制非离子和阳离子表面活性剂的量可以得到分散性较好的介孔二氧化硅球,其平均颗粒直径为2．5μm,平均孔径为3．25nm,比表面为1379m^2／g,孔体积高达1．12cm^3／g。实验讨论了两种表面活性剂的比例对介孔二氧化硅形貌和介相结构的影响,并用混合模板机理解释了不同形貌形成的原因。     

二氧化硅纳米颗粒/硅树脂复合超疏水功能涂层的制备和性能研究

将二氧化硅纳米颗粒和硅树脂制成混合液,采用喷涂法(spray-coating)制备出了具备超疏水性的复合涂层.研究了二氧化硅、硅树脂不同含量配比对涂层疏水性能的影响,结果表明复合涂层的接触角随二氧化硅含量的增加而增加.在二氧化硅含量大于3%(质量分数)时,涂层显现超疏水性;当二氧化硅含量为3%(质量分数)、硅树脂含量为7%(质量分数)时,涂层与水的接触角达到151.6°,滚动角接近0°.通过扫描电子显微镜(SEM)观察涂层表面的微观结构,发现超疏水性的涂层具备微-纳复合阶层结构,类球状突起粒径在5μm左右,类球状突起上分布纳米团聚颗粒,直径约为50 nm.这种类似荷叶表面的微(纳复合阶层结构,结合硅树脂的低表面能,使得复合涂层具备了超疏水性能.     

Surface modification of silica nanoparticles by a polyoxyethylene sorbitan and silane coupling agent to prepare high-performance rubber composites

The interfacial interaction between nano-silica and rubber matrix is very important for the preparation of high-performance rubber composites. In this paper, we first proposed the use of TWEEN-20 as a new silica modifier, it has four long arms consisting of three polyether chains with terminal hydroxyl group and a fatty chain. The oxygen on the polyether can form a hydrogen bond with the silanol groups on silica surface, and the terminal hydroxyl groups can chemically react with the silanol groups without any VOCs. Moreover, the long fatty chain can weaken silica polarity to obtain a better compatibility with rubber, so that silica modified by TWEEN-20 with chemical reaction and physical absorption can homogeneously disperses in rubber matrix. Nextly, we prepared high-performance natural rubber (NR) composites by adjusting the ratio of TWEEN-20 to TESPT to adjust the physical and chemical interaction between nano-silica and rubber molecular chains. The results indicated that the performances, including the filler dispersion, static mechanical properties, and dynamic heating (viscoelastic self-heating), were optimal when the ratio of TESPT to TWEEN-20 was 2:1. In addition, one-third of TESPT was replaced by TWEEN-20 to prepare silica/rubber composites, which can reduce one-third of VOCs, improve “scorchy”, and achieve high dispersion of silica.     

Surface grafting of polymers onto inorganic ultrafine particles: Reaction of functional polymers with acid anhydride groups introduced onto inorganic ultrafine particles

The surface grafting onto inorganic ultrafine particles, such as silica, titanium oxide, and ferrite, by the reaction of acid anhydride groups on the surfaces with functional polymers having hydroxyl and amino groups was examined. The introduction of acid anhydride groups onto inorganic ultrafine particle was achieved by the reaction of hydroxyl groups on these surfaces with 4-trimethoxysilyltetrahydrophthalic anhydride in toluene. The amount of acid anhydride groups introduced onto the surface of ultrafine silica, titanium oxide, and ferrite was determined to be 0.96, 0.47, and 0.31 mmol/g, respectively, by elemental analysis. Functional polymers having terminal hydroxyl or amino groups, such as diol-type poly(propylene glycol) (PPG), and diamine-type polydimethylsiloxane (SDA), reacted with acid anhydride groups on these ultrafine particles to give polymer-grafted ultrafine particles: PPG and SDA were considered to be grafted onto these surfaces with ester and amide bond, respectively. The percentage of grafting increased with increasing acid anhydride group content of the surface: the percentage of grafting of SDA (M_n = 3.9 × 10³) onto silica, titanium oxide, and ferrite reaching 64.7, 33.7, and 24.1%, respectively. These polymer-grafted ultrafine particles gave a stable colloidal dispersion in organic solvents.     

TiO2在水及丙二醇介质中表面电性质的研究

0引言 固体颗粒在液相介质中的分散是基础研究领域和工业技术部门普遍遇到的问题 ?在化学工业领域,如涂料 ? 染料 ? 油墨 ? 化妆品等,固体颗粒的分散及分散稳定性直接影响着产品的质量和性能 ?TiO 2 颗粒的水基分散体系广泛应用于涂料 ? 油墨以及化妆品中,也是陶瓷制备过程中重     

Infrared spectra of geminal and novel triple hydroxyl groups on silica surface

We investigated the O---H stretching frequencies of geminal and triple hydroxyl groups on silica surface by FT-IR spectroscopy. The geminal and triple hydroxyl groups were individually prepared by the chemical reaction of alkylchlorosilane with surface isolated hydroxyl groups which are separated enough and following hydroxylation of surface chlorine groups. The O---H stretching frequencies of these generated geminal and triple hydroxyl groups were observed at frequencies by 2 and 3 cm⁻¹ lower than that of isolated ones, respectively. By heat treatment the triple hydroxyl groups are firstly eliminated, and secondly the geminal hydroxyl groups disappear. Lastly only isolated hydroxyl groups remain on silica surface.     

Ziegler–Natta catalysts on silica for ethylene polymerization

The amount of dibutylmagnesium (DBM) or triethylaluminum (TEAL) that reacted with silica at 55–60°C depended on the silica calcining temperature. Lower silica calcining temperatures resulted in more Mg or Al fixed to the silica surface, indicating greater amounts of DBM or TEAL reacting with the silica. The amount of the metal alkyls butyl(octyl) magnesium ethoxide, ethylaluminum dichloride, tri-n-hexylaluminum, and diethyl(ethyldimethylsilanolato) aluminum that reacted with 600°C calcined silica was also determined. The metal alkyl can react with the silica at two sites, a surface hydroxyl group and a siloxane group. The silica surface hydroxyl groups can be chemically converted to trimethylsilyl groups so that only the siloxane groups are available for attack. After the metal alkyl was reacted with silica, the resulting intermediate was treated with titanium tetrachloride to yield an ethylene polymerization catalyst in the presence of TEAL. When no metal alkyl was employed, titanium tetrachloride reacted only with the silica surface hydroxyl groups to yield a weakly active ethylene polymerization catalyst.     

A Geometrical Model for Chemically Bonded TMS and PDS Phases

Abstract

A geometrical model is developed for monomeric TMS and PDS phases that are chemically bonded to silica. Using experimental data for maximum surface coverage and considering amorphous silica as a collection of distorted crystals, we calculate that each nm² of the silica surface contains 2.3 modified hydroxyl groups, 1.3 free hydroxyl. groups and 0.6 pairs of bonded hydroxyl groups, respectively. From the dimensions of the silane molecule it is concluded that for maximum coverage the TMS and PDS molecules are rigidly attached to the silica surface with an Si-O-Si bond angle between 120 and 140 degrees. The unreacted hydroxyl groups are not completely screened but will be quite inaccessible on either phase. Very little free surface area remains on the silica surface.     

Interaction between Globular Proteins and Silica Surfaces

The adsorption of bovine serum albumin on silica of three different types, i.e., aerosil, macroporous silica gel, and ground natural quartz, was studied. The IR spectra of this protein adsorbed on aerosil were measured and analyzed. It was shown that the carbonyl groups of albumin macromolecules interact with vicinal hydroxyl groups while imido groups, with individual hydroxyl groups of silica surface. The geminal hydroxyl groups of the surface behaved as single adsorption sites with respect to albumin. The number or such sites on quartz surface was estimated. The IR spectra indicated that the adsorption of albumin macromolecules caused the dehydration of aerosil surface and the appearance of a small amount (to 10%) of unfolded -regions in the secondary structure of the adsorbed protein, while the -helical macromolecular structure remains preserved as a whole. Changes in the tertiary structure of the protein resulted from the adsorption were discussed. Protein macromolecules folded into globules were shown to be tilted with respect to the adsorbent surface.     

改性固体表面的吸附作用——甲基化硅胶的热稳定性和吸附性能

本文利用三甲基氯硅烷与硅胶表面羟基反应的方法制备了甲基化硅胶。测定了亲水硅胶和甲基化硅胶的热处理对其自四氯化碳中吸附乙酸的等温线的影响,并配合有热重分析(TG)和红外光谱(IR)的测定。结果表明:(1)甲基化后的硅胶对乙酸的吸附能力大大下降;(2)甲基化硅胶的热处理温度达500℃时吸附能力完全恢复到甲基化前的硅胶的水平,甲基化层明显开始破坏的温度为450℃;(3)甲基化硅胶高温处理后吸附能力得以恢复的主要原因是重新形成表面自由羟基。     

The Thermal Stability and Adsorbability of the Mechylated Silica Gel

The methylated silica gel has been produced by the reaction between the surface silanol groups and Clsi(CH3)3 vapor.The adsorption isotherms of acetic acid from carbon tetrachloride onto silica gel and emthylated silica gel heated at various temperatures have been determined at 25℃,and the above mentioned silica gels have been studied by TC and IR.The results indicate:(1) The adsorption of acetic acid from carbon tetrachloried onto methylated silica gel decreased greatly,probably because the concentration of the free hydroxyl groups for methylated silica gel decreased greatly as the IR shows.(2) As the methylated surface was destroyed at 450℃,the adsorption ability was restored when the methylated silica gel treated at>500℃.(3) So long as the methylated silica gel was treated at high temperature,the adsorption ability could be restored owing to that surface free hydroxyl groups were reproduced.     

无机氧化物载体对催化CO_2与环氧化合物合成环状碳酸酯的促进作用(英文)

以一系列无机氧化物与四丁基溴化铵为双组分催化剂体系,考察了其催化CO2和环氧化合物合成环状碳酸酯的反应性能.结果表明,在四丁基溴化铵与这些本身并没有催化活性的无机氧化物共同作用下,反应活性明显提高,表现出很强的协同催化作用.另外,通过对SiO2的表面硅烷基化,考察了其表面羟基数量对反应活性的影响,发现当SiO2的表面经过硅烷基化以后,反应活性大幅度降低,表明无机氧化物表面羟基对CO2环加成反应活性有非常显著的促进作用.