激波诱导含灰气体边界层中的粒子分布

本文研究当激波沿着一个固体表面等速地穿越含灰气体运动时所诱导的层流边界层特性。考虑了作用在气体边界层中球形粒子的 Saffman 升力,建议了一种计算近壁区中弥散相密度剖面的方法,并给出了数值计算结果。本文结果表明:在激波后方存在着一个弯曲的薄层区域,其中的粒子密度可以比其波前原始值增加许多倍。这种粒子聚集效应对于工业中粉尘爆炸等实际问题具有重要意义。     

Boundary layer flows behind constant speed shock waves moving into a dusty gas

Laminar boundary layer flows behind constant speed shock waves moving into a dusty gas are analyzed numerically. The basic equations of two-phase flows are derived in shock fixed coordinates and solved by an implicit finite-difference method for the side wall boundary layer in a dusty gas shock tube. The development of the boundary layer and resulting velocity and temperature profiles, respectively, for the gas and particles are given from the shock front to far downstream. The effects of diaphragm pressure ratio, mass loading ratio of particles and particle size upon the flow properties are discussed in detail.This article was processed using Springer-Verlag T_EX Shock Waves macro package 1990.     

The flow structure of dilute gas-particle suspensions behind a shock wave moving along a flat surface

The asymptotic and numerical investigations of shock-induced boundary layers in gas-particle mixtures are presented.The Saffman lift force acting on a particle in a shear flow istaken into account.It is shown that particle migration across the boundary layer leads tointersections of particle trajectories.The corresponding modification of dusty gas model isproposed in this paper.The equations of two-phase sidewall boundary layer behind a shock wave moving at aconstant speed are obtained by using the method of matched asymptotic expansions.Themethod of the calculation of particle phase parameters in Lagrangian coordinates isdescribed in detail.Some numerical results for the case of small particle concentration aregiven.     

The distribution of particles in a shock-induced boundary layer of a dusty gas over a solid surface

The laminar boundary layer behind a constant-speed shock wave moving through a dusty gas along a solid surface is studied. The Saffman lift force acting on a spherical particle in a gas boundary layer is taken into account. A method for calculating the density profile of dispersed phase near the wall is proposed and some numerical results are given. It is shown that behind the shock wave, there exists a curved thin layer where the density of particles is many times higher than the original one. This dust collection effect may be of essential importance to the problem of dust explosion in industry.     

Euler flow solutions for transonic shock wave–boundary layer interaction

Steady 2D Euler flow computations have been performed for a wind tunnel section, designed for research on transonic shock wave–boundary layer interaction. For the discretization of the steady Euler equations, an upwind finite volume technique has been applied. The solution method used is collective, symmetric point Gauss–Seidel relaxation, accelerated by non-linear multigrid. Initial finest grid solutions have been obtained by nested iteration. Automatic grid adaptation has been applied for obtaining sharp shocks. An indication is given of the mathematical quality of four different boundary conditions for the outlet flow. Two transonic flow solutions with shock are presented: a choked and a non-choked flow. Both flow solutions show good shock capturing. A comparison is made with experimental results.     

Non-stationary effects in hypersonic nonuniform dusty-gas flow past a blunt body

In the framework of the two-fluid model, a hypersonic flow of a nonuniform dusty gas with low inertial (non-depositing) particles around a blunt body is considered. The particle mass concentration is assumed to be small, so that the effect of particles on the carrier phase is significant only inside the boundary layer where the particles accumulate. Stepshaped and harmonic nonuniformities of the particle concentration ahead of the bow shock wave are considered and the corresponding nonstationary distributions of the particle concentration in the shock layer are studied. On the basis of numerical study of nonstationary two-phase boundary layer equations derived by the matched asymptotic expansion method, the effects of free-stream particle concentration nonuniformities on the thermal flux, and the friction coefficient in the neighborhood of stagnation point are investigated, in particular, the most “dangerous” nonuniformity periods are found. The project supported by the Russian Foundation for Basic Research (project No. 96-01-00313) and the National Natural Science Foundation of China (joint RFBR-NSFC grant No. 96-01-00017c)     

Investigation on onset of shock-induced separation

A great number of experimental data indicating shock wave/boundary layer interactions in internal or external supersonic flows were reviewed to make clear the mechanism of the interaction and to decide the onset of shock-induced separation. The interesting conclusions were obtained for the considerably wide range of flow geometries that the onset of separation is independent of the flow geometries and the boundary layer Reynolds number. It is found that the pressure rise necessary to separate the boundary layer in supersonic external flows could be applied to such internal flows as overexpanded nozzles or diffusers. This is due to the fact that the separation phenomenon caused by shock wave/boundary layer interactions is processed through a supersonic deceleration. The shock-induced separation in almost all of interacting flow fields is governed by the concept of free interaction, and the onset of shock-induced separation is only a function of the Mach number just upstream of shock wave. However, physical scales of the produced separation are not independent of the downstream flow fields.     

Supersonic low-concentration dusty-gas flow past a plane cylinder in the presence of an oblique shock wave interacting with the bow shock

The motion of an inertial dispersed admixture near a plane cylinder immersed in a steady-state hypersonic dusty flow in the presence of an oblique shock wave interacting with the bow shock is considered. It is assumed that the free-stream particle mass concentration is small and the particles do not affect the carrier flow. The III and IV shock wave interaction regimes are considered. The gas flow parameters in the shock layer are calculated from the numerical solution of the full Navier-Stokes equations for the perfect gas. A TVD second-order finite-difference scheme constructed on the basis of a finite volume method is used. For calculating the dispersed-phase parameters, including the concentration, the full Lagrangian method is used. On a wide range of variation of the particle inertia parameters, the patterns of the particle trajectories, velocity, concentration, and temperature in the shock layer are studied. The possibility of aerodynamic focusing of the particles behind the shock wave intersection point and the formation of narrow beams with a high particle concentration is revealed. These beams impinge on the cylinder surface and result in a sharp increase in the local heat fluxes. The maximal possible increase in the heat fluxes caused by the particles colliding with the cylinder surface is estimated for the flows with and without the incident oblique shock wave.     

Interaction of a shock wave with a loose dusty bulk layer

The interaction of a planar shock wave with a loose dusty bulk layer has been investigated both experimentally and numerically. Experiments were conducted in a shock tube. The incident shock wave velocity and particle diameters were measured with the use of pressure transducers and a Malvern particle sizer, respectively. The flow fields, induced by shock waves, of both gas and granular phase were visualized by means of shadowgraphs and pulsed X-ray radiography with trace particles added. In addition, a two-phase model for granular flow presented by Gidaspow is introduced and is extended to describe such a complex phenomenon. Based on the kinetic theory, such a two-phase model has the advantage of being able to clarify many physical concepts, like particulate viscosity, granular conductivity and solid pressure, and deduce the correlative constitutive equations of the solid phase. The AUSM scheme was employed for the numerical calculation. The flow field behind the shock wave was displayed numerically and agrees well with our corresponding experimental results.      

Numerical simulation of 1-D unsteady two-phase flows with shocks

In the present paper, random-choice method (RCM) and second-order GRP difference method, which are high resolution methods used for pure gas flows with shocks, are extended and employed to study the problem of one-dimensional unsteady two-phase flows. The two-phase shock wave and the flow field behind it in a dusty gas shock tube are calculated and the time-dependent change of the fiow parameters for the gas antiparticle phase are obtained. The numerical results indicate that both the two methods can give the relaxation structure of the two-phase shocks with a sharp discontinuous front and that the GRP method has the advantages of less time-consuming and higher accuracy over the RCM method.     

Particle image velocimetry measurements of a shock wave/turbulent boundary layer interaction

Particle image velocimetry is used to investigate the interaction between an incident shock wave and a turbulent boundary layer at Mach 2.1. A particle response assessment establishes the fidelity of the tracer particles. The undisturbed boundary layer is characterized in detail. The mean velocity field of the interaction shows the incident and reflected shock wave pattern, as well as the boundary layer distortion. Significant reversed flow is measured instantaneously, although, on average no reversed flow is observed. The interaction instantaneously exhibits a multi-layered structure, namely, a high-velocity outer region and a low-velocity inner region. Flow turbulence shows the highest intensity in the region beneath the impingement of the incident shock wave. The turbulent fluctuations are found to be highly anisotropic, with the streamwise component dominating. A distinct streamwise-oriented region of relatively large kinematic Reynolds shear stress magnitude appears within the lower half of the redeveloping boundary layer. Boundary layer recovery towards initial equilibrium conditions appears to be a gradual process.     

INTERFERENCE OF SHOCK AND BOUNDARY LAYER IN SUPERSONIC FLOW

激波与物面边界层的干扰涉及可压缩流动的稳定性、转捩、分离等问题,直接影响到飞行器的阻力、表面热防护和飞行性能等工程技术问题。首先总结了前人对于激波与边界层的干扰所做的工作,之后重点研究和对比分析了超声速与跨声速流动中,正激波、斜激波以及头部激波对于飞行器层流和湍流边界层的干扰影响。激波强度的不同对边界层干扰作用不同,在强干扰情况下将会引起边界层分离和翼型失速。     

Three dimensional shock wave/boundary layer interactions

An investigation into a three-dimensional, curved shock wave interacting with a three-dimensional, curved boundary layer on a slender body is presented. Three different nose profiles mounted on a cylindrical body were tested in a supersonic wind tunnel and numerically simulated by solving the Navier–Stokes equations. The conical and hemispherical nose profiles tested were found to generate shock waves of sufficient strength to separate the boundary layer on the cylinder, while the shock wave generated by the ogival profile did not separate the boundary layer. For the separated flow, separation was found to occur predominantly on the windward side of the cylinder with the lee-side remaining shielded from the direct impact of the incident shock wave. A thickening of the boundary layer on the lee-side of all the profiles was observed, and in the conical and hemispherical cases this leads to the re-formation of the incident shock wave some distance away from the surface of the cylinder. A complex reflection pattern off the shock wave/boundary layer interaction (SWBLI) was also identified for the separated flow cases. For comparative purposes, an inviscid simulation was performed using the hemispherical profile. Significant differences between the viscous and inviscid results were noted including the absence of a boundary layer leading to a simplified shock wave reflection pattern forming. The behaviour of the incident shock wave on the lee-side of the cylinder was also affected with the shock wave amalgamating on the surface of the cylinder instead of away from the surface as per the viscous case. Test data from the wind tunnel identified two separation lines present on the cylindrical surface of the hemispherical SWBLI generator. The pair of lines were not explicitly evident in the original CFD simulations run, but were later identified in a high-resolution simulation.     

Time-resolved stereo PIV measurements of shock–boundary layer interaction on a supercritical airfoil

Time-resolved stereo particle-image velocimetry (TR-SPIV) and unsteady pressure measurements are used to analyze the unsteady flow over a supercritical DRA-2303 airfoil in transonic flow. The dynamic shock wave–boundary layer interaction is one of the most essential features of this unsteady flow causing a distinct oscillation of the flow field. Results from wind-tunnel experiments with a variation of the freestream Mach number at Reynolds numbers ranging from 2.55 to 2.79 × 10⁶ are analyzed regarding the origin and nature of the unsteady shock–boundary layer interaction. Therefore, the TR-SPIV results are analyzed for three buffet flows. One flow exhibits a sinusoidal streamwise oscillation of the shock wave only due to an acoustic feedback loop formed by the shock wave and the trailing-edge noise. The other two buffet flows have been intentionally influenced by an artificial acoustic source installed downstream of the test section to investigate the behavior of the interaction to upstream-propagating disturbances generated by a defined source of noise. The results show that such upstream-propagating disturbances could be identified to be responsible for the upstream displacement of the shock wave and that the feedback loop is formed by a pulsating separation of the boundary layer dependent on the shock position and the sound pressure level at the shock position. Thereby, the pulsation of the separation could be determined to be a reaction to the shock motion and not vice versa.     

激波与转捩边界层干扰非定常特性数值分析

激波与边界层干扰的非定常问题是高速飞行器气动设计中基础研究内容之一.以往研究主要针对层流和湍流干扰,在分离激波低频振荡及其内在机理方面存在着上游机制和下游机制两类截然不同的理论解释.分析激波与转捩边界层干扰下非定常运动现象有助于进一步加深理解边界层状态以及分离泡结构对低频振荡特性的影响规律,为揭示其产生机理指出新的方向.采用直接数值模拟方法对来流马赫数2.9,24?压缩拐角内激波与转捩边界层干扰下激波的非定常运动特性进行了数值分析.通过在拐角上游平板特定的流向位置添加吹吸扰动激发流动转捩,使得进入拐角的边界层处于转捩初期阶段.在验证了计算程序可靠性的基础上,详细分析了转捩干扰下激波运动的间歇性和振荡特征,着重研究了分离泡展向三维结构对激波振荡特性的影响规律,最后还初步探索了转捩干扰下激波低频振荡产生的物理机制.研究结果表明:分离激波的非定常运动仍存在强间歇性和低频振荡特征,其时间尺度约为上游无干扰区内脉动信号特征尺度的10倍量级;分离泡展向三维结构不会对分离激波的低频振荡特征产生实质影响.依据瞬态脉动流场的低通滤波结果,转捩干扰下激波低频振荡的诱因来源于拐角干扰区下游,与流场中分离泡的收缩/膨胀运动存在一定的关联.     

HLLE++格式在高马赫数空腔流动模拟中的应用

空腔流动存在剪切层运动、涡脱落与破裂,以及激波与激波、激波与剪切层、激波与膨胀波和激波/涡/剪切层相互干扰等现象,流动非常复杂,特别是高马赫数(M>2)时,剪切层和激波更强,激波与激波干扰更严重,对数值格式的要求更高,既需要格式耗散小,对分离涡等有很高的模拟精度,又需要格式在激波附近具有较大的耗散,可以很好地捕捉激波,防止非物理解的出现。Roe和HLLC等近似Riemann解格式在高马赫数强激波处可能会出现红玉现象,而HLLE++格式大大改善了这种缺陷,在捕捉高超声速激波时避免了红玉现象的发生,同时还保持在光滑区域的低数值耗散特性。本文在结构网格下HLLE++格式的基础上,通过改进激波探测的求解,建立了基于非结构混合网格的HLLE++计算方法,通过无粘斜坡算例,验证了HLLE++格式模拟高马赫数流动的能力,并应用于高马赫数空腔流动的数值模拟,开展了网格和湍流模型影响研究,验证了方法模拟高马赫数空腔流动的可靠性和有效性。     

激波风洞内超燃冲压发动机三面压缩进气道流场实验观测

主要进行了超燃冲压发动机三面压缩进气道的实验观测。利用来流马赫数4.5的直通式激波风洞,考察了三组具有不同压缩角度的进气道模型内部的流场情况。实验观测手段为油流法、丝线法和高速纹影,同时,辅以数值模拟以有助于流场细节分析。纹影照片展示了进气道内部以激波边界层相互作用为主要影响因素的流场复杂结构,数值模拟也显示了相近的结果。油流技术与丝线法显示了近壁面处的流动图像,照片中可见激波、分离线、再附线等分界线位置。根据实验结果,可以推测唇口激波与进气道内边界层的相互作用及其引起的壁面分离是影响进气道内流动的主要因素。同时,尝试了利用抽吸方法减弱激波与边界层相互作用诱发的壁面流动分离,并取得一定结果。     

Mathematical Simulation of Dust Lifting from the Surface

Results of numerical simulation of the shock wave passing along a dusty layer are presented; the simulation was performed under the onetemperature, onevelocity assumption. It is shown that a system of compression and expansion waves is formed inside the layer, and these waves are successively reflected from the external boundary and solid wall. Regular and irregular reflections of the leading shock wave from the solid wall with different scenarios of instability evolution on the layer edge are described. Possible mechanisms of particle lifting from the surface are described.     

Effect of pressure gradient of friction and heat transfer in a dusty boundary layer

Approximate analytic expressions for the local friction and heat transfer coefficients in a dusty laminar boundary layer are obtained and tested in the case of an incompressible carrier phase, power-law variation of the external gas flow velocity and small velocity and temperature phase disequilibrium. These expressions supplement the numerical analysis of the dusty boundary layer on a blunt body [1, 2] and the asymptotic calculation of the friction and heat transfer in a quasiequilibrium dusty gas boundary layer on a plate [3]. The combined effect of dustiness and pressure gradient on the friction and heat transfer coefficients is discussed. The results obtained can be used for the practical calculation of the friction and heat transfer in a quasiequilibrium dusty laminar boundary layer and for interpreting the corresponding experimental data. Tomsk. Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 5, pp. 105–108, September–October, 1988.