Polyelectrolyte layer-by-layer self-assembly enhanced by electric field and their multilayer membranes for separating isopropanol–water mixtures

An electric field enhanced method is developed for fabricating layer-by-layer (LbL) self-assembly polyelectrolyte multilayer membranes. Three kinds of electric field enhanced polyelectrolyte multilayer membranes (EPEMs), poly(diallyl dimethylammonium chloride)/poly(styrenesulfonate sodium salt) (PDDA/PSS), poly(diallyldimethylammonium chloride)/poly(acrylic acid sodium salt) (PDDA/PAA) and polyethylenimine/poly(acrylic acid sodium salt) (PEI/PAA), were self-assembled on a reverse osmosis membrane (ROM). The pervaporation performances of EPEMs for separating isopropanol–water mixtures (90/10, w/w) are all superior to those of corresponding normal self-assembled polyelectrolytes membranes (PEMs), and the selectivity increases with PDDA/PSS, PDDA/PAA and PEI/PAA in order. For (PEI/PAA)₄PEI EPEM, the separation factor is 1075 and permeation flux is 4.05 kg m⁻² h⁻¹ at 70 °C. This novel method speeds up the LbL process, which makes it promising for the practical application of the LbL multilayer membrane.     

Highly sensitive and fast responsive fiber-optic modal interferometric pH sensor based on polyelectrolyte complex and polyelectrolyte self-assembled nanocoating

A new fiber-optic pH sensor is demonstrated by coating negatively charged polyelectrolyte complex (PEC⁻) nanoparticles, made of sodium carboxymethyl cellulose and poly(diallyldimethylammonium chloride) (PDDA), and positively charged PDDA on the surface of a thin-core fiber modal interferometer (TCFMI) with a layer-by-layer (LbL) electrostatic self-assembly method. The fabricated TCFMI pH sensor has different transmission dip wavelengths under different pH values and shows high sensitivities of 0.6 nm/pH unit and −0.85 nm/pH unit for acidic and alkaline solutions, respectively, and short response time of 30–50 s. The LbL electrostatic self-assembly process of a PEC⁻/PDDA multilayer is traced by quartz crystal microbalance and shows a fast thickness growth. Atomic force microscopy shows the root mean square (RMS) surface roughness of electrostatic self-assembly nanocoating of polyelectrolyte complex/polyelectrolyte is much higher than that of polyelectrolyte/polyelectrolyte due to the larger size of PEC⁻ colloidal nanoparticles. The enhanced RMS surface roughness and thickness of the nanocoating can shorten the response time and raise the sensitivity of the TCFMI pH sensor, respectively. In addition, the TCFMI pH sensor has highly reversible performance and good durability.     

A novel amperometric biosensor based on single walled carbon nanotubes with acetylcholine esterase for the detection of carbaryl pesticide in water

Amperometric biosensor is fabricated for the detection of carbaryl based on single walled carbon nanotubes (SWCNTs) and acetylcholine esterase (AchE). The dispersion of SWCNTs in positively charged polyelectrolyte, poly(diallyldimethylammonium chloride) (PDDA), possibly takes place due to weak supramolecular interaction between them, which then binds electrostatically to the negatively charged AchE at pH 7.4 using layer-by-layer (LbL) self-assembly technique. The optical intensity of UV/vis spectra increased with the number of layers, indicating the build up of a multilayer coating on the electrode. The activity of acetylcholine esterase on modified electrode of 3 mm in diameter was found to be 0.2 U. The biosensor showed good sensitivity and stability towards the monitoring of carbaryl pesticides in water with the detection limit of 10⁻¹² g L⁻¹ and recovery of 99.8 ± 2.7% to 10⁻¹⁰ g L⁻¹. This protocol can be used for the immobilization of other enzymes to fabricate a range of biosensors.     

Naked-eye colorimetric analysis of Hg2+ with bi-color CdTe quantum dots multilayer films

A novel direct quantificational method through naked-eye colorimetric analysis of Hg²⁺ was constructed based on different degree of the fluorescence quenching of bi-color quantum dots (QDs) multilayer films (2-QDMF). The functional multilayer films were assembled by layer-by-layer (LBL) deposition of oppositely charged CdTe QDs and poly(dimethyldiallylemmonium chloride) (PDDA). Then the outermost layer of 2-QDMF was cross-linked to bovine serum albumin (BSA), polyethylene glycol (PEG) or glutathione (GSH). It was found that when BSA modified quartz slides were immersed into solutions containing Hg²⁺ and Cu²⁺ respectively, the 2-QDMF can be quenched by Hg²⁺, but not by Cu²⁺. Under the optimization conditions, the quenched photoluminescence (PL) intensities of multilayer films were almost linearly proportional to the concentration of Hg²⁺ in the range of 1.0 × 10⁻⁸ to 1.0 × 10⁻⁶ mol L⁻¹ and the detection limit was 4.5 × 10⁻⁹ mol L⁻¹. The proposed method is intuitional and convenient, which can be applied to the determination of trace Hg²⁺ in the artificial water sample with satisfactory results.     

Tuning the selectivity of polymeric ionic liquid sorbent coatings for the extraction of polycyclic aromatic hydrocarbons using solid-phase microextraction

A new generation polymeric ionic liquid (PIL), poly(1-4-vinylbenzyl)-3-hexadecylimidazolium bis[(trifluoromethyl)sulfonyl]imide (poly(VBHDIm⁺ NTf₂⁻)), was synthesized and is shown to exhibit impressive selectivity towards the extraction of 12 polycyclic aromatic hydrocarbons (PAHs) from aqueous samples when used as a sorbent coating in direct-immersion solid-phase microextraction (SPME) coupled to gas chromatography (GC). The PIL was imparted with aromatic character to enhance π–π interactions between the analytes and the sorbent coating. For comparison purposes, a PIL with similar structure but lacking the π–π interaction capability, poly(1-vinyl-3-hexadecylimidazolium bis[(trifluoromethyl)sulfonyl]imide) (poly(HDIm⁺ NTf₂⁻)), as well as a commercial polydimethylsiloxane (PDMS) sorbent coating were evaluated and exhibited much lower extraction efficiencies. Extraction parameters, including stir rate and extraction time, were studied and optimized. The detection limits of poly(VBHDIm⁺ NTf₂⁻), poly(HDIm⁺ NTf₂⁻), and PDMS coatings varied between 0.003–0.07 μg L⁻¹, 0.02–0.6 μg L⁻¹, and 0.1–6 μg L⁻¹, respectively. The partition coefficients (log K_fs) of eight PAHs to the three studied fiber coatings were estimated using a static SPME approach. This study represents the first report of analyte partition coefficients to any PIL-based material.     

Fabrication of free-standing multilayer films by using pH-responsive microgels as sacrificial layers

A facile way to prepare free-standing polyelectrolyte multilayer films of poly(sodium 4-styrenesulfonate)(PSS)/poly(diallyldimethylammonium)(PDDA) was developed by applying a new pH-dependent sacrificial system based on cross-linked poly(N,N-dimethylaminoethyl methacrylate) (PDMAEMA) microgels. The tertiary amine groups of PDMAEMA microgels can be protonated in acidic environment, and the protonated microgels were deposited by layer-by-layer (LbL) technique with PSS. PSS/PDDA multilayer films were constructed on the top of the PSS/microgels sacrificial layers. The LbL assembly process was investigated by UV–vis spectroscopy. Further study shows that the free-standing PSS/PDDA multilayer films can be obtained within 3 min by treating the as-prepared films in alkali aqueous solution with a pH of 12.0. The pH-triggered exfoliation of PSS/PDDA multilayer films provides a simple and facile way to prepare LbL assembled free-standing multilayer films.     

A facile route for fabricating novel polyelectrolyte complex membrane with high pervaporation performance in isopropanol dehydration

Polyelectrolyte complexes (PECs) of sodium carboxymethyl cellulose (CMCNa) and poly(diallyldimethylammonium chloride) (PDDA) were prepared in dilute hydrochloric acid (HCl) aqueous solution and obtained in its solid form. Element analysis and FT-IR showed that the composition of PECs could effectively be tuned by the concentration of HCl in parent polyelectrolyte solution. The PECs were then dissolved in 0.1 mol/L aqueous NaOH and subsequently cast onto polysulfone ultra-filtration membrane. This composite membrane, which has a unique homogeneous PECs separation layer, was subjected to pervaporation test for the first time and gave a performance of J = 3.0 kg/m² h, α = 960 for 10 wt% water–isopropanol feed at 75 °C. Meanwhile, performance of the PECs membrane displays good stability and unique dependence on feed temperature. These findings, together with its ultra-high performance, are primarily explained by the structure characteristic of PECs.     

聚电解质PDDA/PSS层层自组装膜的渗透汽化性能

采用聚电解质层层自组装(LbL)技术, 在不同盐浓度下制备了聚(二烯丙基二甲基氯化铵)/聚苯乙烯磺酸钠(PDDA/PSS) 多层自组装膜, 并用于渗透汽化性能的研究. 重点考察了组装溶液中NaCl的浓度、组装层数及操作温度对自组装膜的异丙醇脱水性能的影响. 同时, 用扫描电镜观测了不同条件下制备膜的表面形貌. 结果表明, 在高NaCl含量的聚电解质溶液中只需组装几个双层的LbL膜, 即能获得较高的分离因子和较大的通量, 并解释了该LbL膜呈现反“trade-off”现象的原因.     

Highly phosphonated polypentafluorostyrene: Characterization and blends with polybenzimidazole

In this study we present results of the conductivity and resistance to thermooxidative and condensation reactions of a highly phosphonated poly(pentafluorostyrene) (PWN2010) and of its blends with poly(benzimidazole)s (PBI). This polymer, which combines both: (i) a high degree of phosphonation (above 90%) and (ii) a relatively high acidity (pK_a (–PO₃H₂ ↔ –PO₃H⁻) ∼ 0.5) due to the fluorine neighbors, is designed for low humidity operating fuel cell. This was confirmed by the conductivity measurements for PWN2010 reaching σ = 5 × 10⁻⁴ S cm⁻¹ at 150 °C in dry N₂ and σ = 1 × 10⁻³ S cm⁻¹ at 150 °C (λ = 0.75). Furthermore, this polymer showed only 48% of anhydride formation when annealing it at T = 250 °C for 5 h and only 2% weight loss during a 96 h Fenton test. These properties combined with the ability of the PWN2010 to form homogeneous blends with polybenzimidazoles resulting in stable and flexible polymer films, makes PWN2010 a very promising candidate as a polymer electrolyte for intermediate- and high-temperature fuel cell applications.     

Ultra-sensitive determination of cyanide in surface water by gas chromatography–tandem mass spectrometry after derivatization with 2-(dimethylamino)ethanethiol

A gas chromatography–tandem mass spectrometric (GC–MS/MS) method has been established for the determination of cyanide in surface water. This method is based on the derivatization of cyanide with 2-(dimethylamino)ethanethiol in surface water. The following optimum reaction conditions were established: reagent dosage, 0.7 g L⁻¹ of 2-(dimethylamino)ethanethiol; pH 6; reaction carried out for 20 min at 60 °C. The organic derivative was extracted with 3 mL of ethyl acetate, and then measured by using GC–MS/MS. Under the established conditions, the detection and quantification limits were 0.02 μg L⁻¹ and 0.07 μg L⁻¹ in 10-mL of surface water, respectively. The calibration curve had a linear relationship relationship with y = 0.7140x + 0.1997 and r² = 0.9963 (for a working range of 0.07–10 μg L⁻¹) and the accuracy was in a range of 98–102%; the precision of the assay was less than 7% in surface water. The common ions Cl⁻, F⁻, Br⁻, NO₃⁻, SO₄²⁻, PO₄³⁻, K⁺, Na⁺, NH₄⁺, Ca²⁺, Mg²⁺, Ba²⁺, Mn⁴⁺, Mn²⁺, Fe³⁺, Fe²⁺ and sea water did not interfere in cyanide detection, even when present in 1000-fold excess over the species. Cyanide was detected in a concentration range of 0.07–0.11 μg L⁻¹ in 6 of 10 surface water samples.     

FTIR and fluorescence studies on the ground and excited state hydrogen-bonding interactions between 1-methylindole and water in water–triethylamine mixtures

The ground and excited state π-hydrogen-bonding interactions between 1-methylindole, MI, and water have been investigated in water–triethylamine, water–TEA, mixtures. FTIR measurements performed on the OH stretching bands of the water–TEA clusters show that, upon MI addition, the typical bands of the water–TEA system at 3348 cm⁻¹, 3440 cm⁻¹, 3545 cm⁻¹ and 3682 cm⁻¹ diminish, whereas two new absorption bands at 3316 cm⁻¹ and 3654 cm⁻¹ grow up. These spectral changes have been rationalised assuming the formation of only one 1:1 water–MI complex, in which the dangling protons in the water–TEA clusters are hydrogen bonded to the π-cloud of the MI aromatic ring. Steady state and time resolved fluorescence measurements provide additional proofs on the ground state formation of a fluorescent OH ? π hydrogen bonded complex. The relevance that the present and the previously reported results could have on the indole ring photophysics is discussed.     

Self-assembly of inner skin hollow fiber polyelectrolyte multilayer membranes by a dynamic negative pressure layer-by-layer technique

In the past studies, electrostatic layer-by-layer (LbL) adsorption of oppositely charged polyelectrolytes has proven to be a promising method for the preparation of polyelectrolyte multilayer membranes (PEMMs). Till now, this method was mainly used to assemble flat sheet and tubular membranes. Since hollow fiber membrane has some advantages such as high-packing density, self-contained mechanical support and hence the consequent economical superiority, this study therefore seeked to assemble inner skin hollow fiber PEMMs by using a dynamic LbL adsorption technique. The assembly process was successfully accomplished by alternatively dynamically filtrating polyacrylic acid (PAA) and polyethyleneimine (PEI) on a hydrolyzed hollow fiber polyacrylonitrile (PAN) membrane under a negative pressure condition. In the case of pervaporation separation of 95 wt.% ethanol–water mixture (50 °C), the membrane obtained with only 4.5 and 6.5 bilayers had separation factor of 245 and 1338 while the permeate fluxes were 290 and 120 g/(m² h), respectively. The pervaporation separation behavior of various alcohol/water mixtures with the alcohols being t-butanol, 2-propanol and ethanol were also investigated. Finally, scanning electron microscopy and atomic force microscopy clearly confirms a uniform and defect-free layer formed on the inner surface of hollow fiber support. Since different polyelectrolyte pairs could be used to assemble PEMMs for different uses, it was expected that the dynamic negative pressure LbL adsorption technique could also potentially be used to prepare many types of PEMMs in other fields.     

A novel magnetic poly(aniline-naphthylamine)-based nanocomposite for micro solid phase extraction of rhodamine B

A novel Fe₃O₄–poly(aniline-naphthylamine)-based nanocomposite was synthesized by chemical oxidative polymerization process as a magnetic sorbent for micro solid phase extraction. The scanning electron microscopy images of the synthesized nanocomposite revealed that the copolymer posses a porous structure with diameters less than 50 nm. The extraction efficiency of this sorbent was examined by isolation of rhodamine B, a mutagenic and carcinogenic dye, from aquatic media in dispersion mode. Among different synthesized polymers, Fe₃O₄/poly(aniline-naphthylamine) nanocomposite showed a prominent efficiency. Parameters including the desorption solvent, amount of sorbent, desorption time, sample pH, ionic strength, extraction time and stirring rate were optimized. Under the optimum condition, a linear spiked calibration curve in the range of 0.35–5.00 μg L⁻¹ with R² = 0.9991 was obtained. The limits of detection (3S_b) and limits of quantification (10S_b) of the method were 0.10 μg L⁻¹ and 0.35 μg L⁻¹ (n = 3), respectively. The relative standard deviation for water sample with 0.5 μg L⁻¹ of RhB was 4.2% (n = 5) and the absolute recovery was 92%. The method was applied for the determination of rhodamine B in dishwashing foam, dishwashing liquid, shampoo, pencil, matches tips and eye shadows samples and the relative recovery percentage were in the range of 94–99%.     

Composite membranes prepared from glutaraldehyde cross-linked sulfonated cardo polyetherketone and its blends for the dehydration of acetic acid by pervaporation

Cardo polyetherketone (PEK-C) composite membranes were prepared by casting glutaraldehyde (GA) cross-linked sulfonated cardo polyetherketone (SPEK-C) or silicotungstic acid (STA) filled SPEK-C and poly(vinyl alcohol) (PVA) blending onto a PEK-C substrate. The compatibility between the active layer and PEK-C substrate is improved by immersing the PEK-C substrate in a GA cross-linked sodium alginate (NaAlg) solution and using water–dimethyl sulfoxide (DMSO) as a co-solvent for preparing the STA-PVA-SPEK-C/GA active layer. The pervaporation (PV) dehydration of acetic acid shows that permeation flux decreased and separation factor increased with increasing GA content in the homogeneous membranes. The permeation flux achieved a minimum and the separation factor a maximum when the GA content increased to a certain amount. Thereafter the permeation flux increased and the separation factor decreased with further increasing the GA content. The PV performance of the composite membranes is superior to that of the homogeneous membranes when the feed water content is below 25 wt%. The permeation activation energy of the composite membranes is lower than that of the homogeneous membranes in the PV dehydration of 10 wt% water in acetic acid. The STA-PVA-SPEK-C-GA/PEK-C composite membrane using water–DMSO as co-solvent has an excellent separation performance with a flux of 592 g m⁻² h⁻¹ and a separation factor of 91.2 at a feed water content of 10 wt% at 50 °C.     

Ab initio/DFT theory and multichannel RRKM study on the mechanisms and kinetics for the CH3S + CO reaction

The potential energy surface for the reaction of CH₃S with CO was calculated at the G3MP2//B3LYP/6-311++G(d,p) level. The rate constants for feasible channels leading to several products were calculated by TST and multichannel-RRKM theory. The results show that addition–elimination mechanism is dominant, while hydrogen abstraction mechanism is uncompetitive. The major channel is the addition of CO to CH₃S leading to an intermediate CH₃SCO which then decomposes to CH₃ + OCS. In the temperature range of 200–3000 K, the overall rate constants are positive temperature dependence and pressure independence, and it can be described by the expression as k = 1.10 × 10⁻¹⁶T^1.57exp(−3359/T) cm³ molecule⁻¹ s⁻¹. At temperature between 208 and 295 K, the calculated rate constants are in good agreement with the experimental upper limit data. At T = 1000 and 2000 K, the major product is CH₃ + OCS at lower pressure; while at higher pressure, the stabilization of IM1 is dominant channel.     

Revision of iron(III)–citrate speciation in aqueous solution. Voltammetric and spectrophotometric studies

A detailed study of iron (III)–citrate speciation in aqueous solution (θ = 25 °C, I_c = 0.7 mol L⁻¹) was carried out by voltammetric and UV–vis spectrophotometric measurements and the obtained data were used for reconciled characterization of iron (III)–citrate complexes. Four different redox processes were registered in the voltammograms: at 0.1 V (pH = 5.5) which corresponded to the reduction of iron(III)–monocitrate species (Fe:cit = 1:1), at about −0.1 V (pH = 5.5) that was related to the reduction of FeL₂⁵⁻, FeL₂H⁴⁻ and FeL₂H₂³⁻ complexes, at −0.28 V (pH = 5.5) which corresponded to the reduction of polynuclear iron(III)–citrate complex(es), and at −0.4 V (pH = 7.5) which was probably a consequence of Fe(cit)₂(OH)_x species reduction. Reversible redox process at −0.1 V allowed for the determination of iron(III)–citrate species and their stability constants by analyzing E_p vs. pH and E_p vs. [L⁴⁻] dependence. The UV–vis spectra recorded at varied pH revealed four different spectrally active species: FeLH (log β = 25.69), FeL₂H₂³⁻ (log β = 48.06), FeL₂H⁴⁻ (log β = 44.60), and FeL₂⁵⁻ (log β = 38.85). The stability constants obtained by spectrophotometry were in agreement with those determined electrochemically. The UV–vis spectra recorded at various citrate concentrations (pH = 2.0) supported the results of spectrophotometric–potentiometric titration.     

Ternary liquid–liquid equilibria for (water + terpene + 1-propanol or 1-butanol) systems at the temperature 298.15 K

Liquid–liquid equilibria and tie-lines for the ternary (water + 1-propanol + α-pinene, β-pinene or limonene) and (water + 1-butanol + α-pinene, β-pinene or limonene) mixtures have been measured at T = 298.15 K. The experimental ternary liquid–liquid equilibrium data have been successfully represented using the additional ternary parameters as well as the binary parameters in terms of the extended and modified UNIQUAC models.     

Self-assembled polyelectrolyte multilayered films on Nafion with lowered methanol cross-over for DMFC applications

The paper is concerned with the deposition of self-assembled polyelectrolyte multilayer on Nafion membrane by layer-by-layer (LbL) technique with lowered methanol cross-over for direct methanol fuel cell (DMFC) applications. The formation of self-assembled multilayered film on Nafion was characterized by UV–vis spectroscopy and it was found that the polyelectrolyte layers growth on the Nafion surface regularly. Furthermore, the proton conductivity and methanol cross-over measurements were carried out for characterization of the LbL self-assembled composite membranes. The results showed that the concentration and pH of the polyelectrolytes significantly affect the proton conductivity and methanol barrier properties of the composite membranes. 10⁻¹ monomol polyelectrolyte concentration and pH 1.8 was found to be optimum deposition conditions considering proton conductivity and methanol permeation properties of the LbL self-assembled composite membranes. The methanol permeability of the 10 bi-layers of PAH1.8/PSS1.8 deposited LbL self-assembly composite membrane was significantly suppressed and found to be 4.41 × 10⁻⁷ cm²/s while the proton conductivity value is in acceptable range for fuel cell applications.     

Modeling of the three-phase equilibrium in systems of the type water + nonionic surfactant + alkane

Liquid–liquid equilibria of systems water (A) + C_iE_j surfactant (B) + n-alkane (C) have been modeled by a mass-action law model previously developed and so far successfully applied to a series of binary water + C_iE_j systems and to the ternary system water + C₄E₁ + n-dodecane. These calculations provide the basis for the presented modeling. The aqueous systems give information about the association constants and the χ_AB-parameter of the Flory–Huggins theory and the ternary C₄E₁-system provides universal temperature functions for the χ_AC- and the χ_BC-parameter. The three-phase equilibrium for seven ternary C_iE_j systems (i = 6–12, j = 3–6) has been calculated by fitting one additional parameter for each of both temperature functions to the characteristic “fish-tail” point. The agreement with the experimental data is reasonably well. For systems with very small three-phase areas the results can considerably be improved by individual temperature functions that incorporate the experimental temperature maximum of the “fish” into the parameter fit. Based on the parameters of the system water + C₈E₄ + n-C₈H₁₈ the “fish-shaped” phase diagram of the system water + C₈E₄ + n-C₁₄H₃₀ was predicted reasonably well.     

The performance of hybrid monolithic silica capillary columns prepared by changing feed ratios of tetramethoxysilane and methyltrimethoxysilane

The effect of a feed ratio of methyltrimethoxysilane (MTMS) to tetramethoxysilane (TMOS) was studied to improve the performance of a hybrid monolithic silica capillary column with 100-μm i.d. in HPLC in a range MTMS/TMOS (v/v) = 10/90–25/75. The domain size was also varied by adjusting the amount of PEG to control permeability (K = 2.8 × 10⁻¹⁴–6.9 × 10⁻¹⁴ m²). Evaluation of the performance for those capillary columns following octadecylsilylation proved an increase in retention factor (k) and a decrease in steric selectivity α(triphenylene/ortho-terphenyl) with the increase in MTMS content in the feed. The effect of the feed ratio was also observed in porosity and hydrophobic property of the C18 stationary phase from the results of size exclusion chromatography (SEC) and reversed phase characterization. The monolithic silica capillary columns prepared under new preparation conditions were able to produce a plate height of 4.6–6.0 μm for hexylbenzene in a mobile phase acetonitrile/water = 80/20 at a linear velocity of 2 mm/s. Consequently, it was possible to prepare hybrid monolithic silica capillary columns with higher performance than those reported previously while maintaining the retention factors in a similar range by reducing the MTMS/TMOS ratio and increasing the total silane concentration in feed.