ArF-excimer laser ablation experiments on Cycloolefin Copolymer (COC)

To determine the capability of Cycloolefin Copolymer (COC) for excimer laser microstructuring, ablation experiments have been performed at 193 nm using an ArF excimer laser workstation. A matrix of square holes was structured in COC, the ablated structures were examined qualitatively and quantitatively by optical methods and scanning electron microscopy. It turned out that COC can be structured with high accuracy and is therefore suited for laser rapid prototyping of micro optical and microfluidic devices. The maximum ablation depth of COC (0.17 μm/pulse) is smaller than of PMMA (0.58 μm/pulse), but is sufficient for prototyping and allows fine depth tuning. Flat structures less than 200-μm deep nearly show no amount of redeposited material and yield smooth surfaces.     

Femtosecond laser induced photoluminescence in poly(methyl methacrylate) and three-dimensional optical storage

We report on a femtosecond-laser induced photoluminescence (PL) in poly(methyl methacrylate) and its potential application to three-dimensional optical storage. Irradiation with a focused 800 nm, 1 kHz, 100 fs pulsed laser induced a strong PL change in UV-visible region. Absorption spectra and Fourier-transform infrared spectra before and after laser irradiation indicate the PL may result from the emissive oxidized products of photo-degradation reaction of PMMA. This makes it possible to read out the stored data by detecting the PL change. The pulse energy threshold of the light-induced PL change of PMMA is found to be at ∼2 μJ/pulse and the optimal recording energy is ∼3 μJ/pulse. A ten-layer pattern inside the bulk sample recorded by tightly focusing a pulsed laser beam was read out by a reflection-type fluorescent confocal microscope, which detected the emission in visible range as the signal. High-contract fluorescent images with a much higher signal-to-noise ratio were obtained without crosstalk in comparison with the ordinary reflection mode.     

Radiation effects on poly(methyl methacrylate) induced by pulsed laser irradiations

Poly(methyl methacrylate) (PMMA) was irradiated using a medical UV-ArF excimer laser operating at the fundamental wavelength of 193 nm. Characterized by a beam diameter of 1.8 mm and energy of 180 mJ with a Gaussian energy profile, it operates in a single mode or at 30 Hz repetition rate. Mechanical profilometry was carried out on ablation craters in order to study the rugosity and the ablation yield in the various operative conditions. Optical transmission and reflection measurements at six wavelengths were conducted in order to characterize the optical properties of the irradiated surfaces. Measured crater depths in PMMA were lower with respect to the forecasted ones in corneal tissue, while the lateral crater aperture was maintained. The rugosity produced at the crater bottom after irradiation was about 0.3 μm, and the ablation yield was about 10¹⁵ molecules/laser pulse, while etching depth and diameter show a roughly linear dependence on the number of laser shots. These experiments constitute a base for deeper clinical investigations.     

Fabrication of an integrated optical Mach-Zehnder interferometer based on refractive index modification of polymethylmethacrylate by krypton fluoride excimer laser radiation

It is known that deep ultraviolet (UV) radiation induces a refractive index increase in the surface layer of polymethylmethacrylate (PMMA) samples. This effect can be used for the fabrication of integrated optical waveguides. PMMA is of considerable interest for bio and chemical sensing applications because it is biocompatible and can be micromachined by several methods, e.g. structuring by photolithography, ablation and hot embossing. In the presented work direct UV irradiation of a common PMMA substrate by a krypton fluoride excimer laser beam through a contact mask has been used to write integrated optical Mach-Zehnder interferometers (MZI). MZI are used as sensitive bio and chemical sensors. The aim was to determine contact mask design and laser irradiation parameters for fabricating single-mode MZI for the infrared region from 1.30 μm to 1.62 μm. Straight and curved waveguides have been generated and characterized to determine the optical losses. The generation of channel waveguide structures has been optimized by a two step irradiation process to minimize the lithographic writing time and optical loss. By flood exposure to UV laser radiation in the first step the optical absorption of PMMA can be increased in the irradiated region. The required refractive index profile is then achieved with a second lithographic irradiation. The spectral behaviour of an unbalanced, integrated optical MZI fabricated by this excimer laser based contact mask method is shown for the first time. Further the optical intensity at the output port of a MZI has been measured while the optical path length difference was tuned by creating a temperature difference between the two arms of the MZI.     

Effect of laser treatment on the optical properties of poly(methyl methacrylate) thin films

In this work, the effect of laser pulse treatment on the optical properties of poly(methyl methacrylate) (PMMA) films has been studied experimentally. The second harmonic of a pulsed Nd:YAG laser at 532 nm and 6 ns pulse width with 10 Hz repetition rate was used to modify the surface of red-BS-dye-doped PMMA films. Samples were ablated with 50 and 100 laser pulses. Optical reflectance and transmittance spectra were obtained in the range of 200–2000 nm. The optical properties of the films were influenced by the pulse number significantly. The oscillator and dispersion energies of the films were determined using the Wemple-Didomenico model. The optical band gap energy was extracted using the Tauc method. Results show that the optical parameters of the films were changed significantly after laser treatment.     

High-repetition-rate femtosecond laser micromachining of poly(methyl methacrylate)

Investigations are performed to explore high-repetition-rate femtosecond laser ablation effects on the physical and chemical properties of poly(methyl methacrylate)(PMMA). A scanning electron microscopy(SEM) is used to characterize the morphology change in the laser-ablated regions. The infrared and Raman spectroscopy reveals that the fundamental structure of the PMMA is altered after laser ablation. We demonstrate the cumulative heating is much greater during high-repetition-rate femtosecond laser ablation, supporting a photothermal depolymerization mechanism during the ablation process.     

聚合物材料PMMA/DR1光漂白过程中折射率的变化

用双光束扫描法研究了在488nm的Ar^ 激光照射下，聚合物材料RMMA／DR1的光漂白过程，为精确测量光漂白模型中的参数提供了一种简单实验方法。这对于今后用光漂白的方法制备光波导器件具有重要意义。     

Phase Separation in Poly(Methyl Methacrylate)-Epoxy Blend

Diglycidyl ether of bisphenol A (DGEBA) epoxy resin was modified with high molecular weight poly(methyl methacrylate) (PMMA). Morphological variations of a 2 wt% PMMA-modified epoxy mixture were studied by optical microscopy and scanning electron microscopy (SEM). A PMMA-epoxy blend cured at 100°C revealed that a secondary phase morphology was observed in both epoxy and PMMA phases from the early stages of the phase separation process. A morphology consisting of a rough striated continuous phase along with large smooth regions was observed by SEM, confirming the secondary phase separation. The dynamic mechanical thermal analysis showed that the PMMA modification of epoxy at such a low PMMA concentration of 2 wt% has no major influence on the glass transition temperature of the epoxy-rich phase. The PMMA-epoxy blend showed a slight increase in the flexural properties and the fracture toughness.     

IR laser ablation of doped poly(methyl methacrylate)

We investigate the TEA CO₂ laser ablation of films of poly(methyl methacrylate), PMMA, with average M_W 2.5, 120 and 996 kDa doped with photosensitive compounds iodo-naphthalene (NapI) and iodo-phenanthrene (PhenI) by examining the induced morphological and physicochemical modifications. The films casted on CaF₂ substrates were irradiated with a pulsed CO₂ laser (10P(20) line at 10.59 μm) in resonance with vibrational modes of PMMA and of the dopants at fluences up to 6 J/cm². Laser induced fluorescence probing of photoproducts in a pump and probe configuration is carried out at 266 nm. Formation of naphthalene (NapH) and phenanthrene (PhenH) is observed in NapI and PhenI doped PMMA, respectively, with relatively higher yields in high M_W polymer, in similarity with results obtained previously upon irradiation in the UV at 248 nm. Above threshold, formation of photoproducts is nearly complete after 200 ms. As established via optical microscopy, bubbles are formed in the irradiated areas with sizes that depend on polymer M_W and filaments are observed to be ejected out of the irradiated volume in the samples made with high M_W polymer. The implications of these results for the mechanisms of polymer IR laser ablation are discussed and compared with UV range studies.     

Refractive and reflective behavior of polymer prisms used for surface plasmon guidance

Two-dimensional optics with surface plasmons was realized by the use of topographically structured dielectric polymer coatings. Triangles of polymethylmetacrylate (PMMA) with lateral dimensions of some tens of micrometers on top of a silver layer act as two-dimensional prisms for surface plasmons. Refraction and internal reflection of plasmons were investigated by scanning near-field optical microscopy. The change in propagation direction can be explained by Snell's law when taking an effective refractive index for plasmons into account. Furthermore, intensity modulations in the PMMA elements and in the transmitted plasmon beam were observed.     

F2-laser patterning of indium tin oxide (ITO) thin film on glass substrate

This paper reports the controlled micromachining of 100 nm thick indium tin oxide (ITO) thin films on glass substrates with a vacuum-ultraviolet 157 nm F₂ laser. Partial to complete film removal was observed over a wide fluence window from 0.49 J/cm² to an optimized single pulse fluence of 4.5 J/cm² for complete film removal. Optical microscopy, atomic force microscopy, and energy dispersive X-ray analysis show little substrate or collateral damage by the laser pulse which conserved the stoichiometry, optical transparency and electrical conductivity of ITO coating adjacent to the trenches. At higher fluence, a parallel micron sized channel can be etched in the glass substrate. The high photon energy and top-hat beam homogenized optical system of the F₂ laser opens new means for direct structuring of electrodes and microchannels in biological microfluidic systems or in optoelectronics. PACS 79.20.Ds; 42.62.Cf; 42.55.Lc     

Nonlinear optical switching and all-figures of merit in Bi2S3-xSex/PMMA nanocomposite films investigated by Z scan under visible CW laser

Bi2S3-xSex/poly(methyl methacrylate)(PMMA)nanocomposite films were prepared using microwave assisted synthesis with different compositions of x.Crystal structure,surface morphology,and optical properties were investigated to characterize the prepared nanocomposite films.The crystallinity and optical band gap of the prepared Bi2S3-xSex/PMMA were affected by x.The prepared samples showed a blue shift in the absorption edge.The laser power dependent nonlinear refraction and absorption of Bi2S3-xSex/PMMA nanocomposite films were investigated by using the Z-scan technique.The optical nonlinearity of the nanocomposite films exhibited switchover from negative nonlinear refraction to positive nonlinear refraction to negative nonlinear refraction effects,and from saturable absorption to reverse saturable absorption to saturable absorption with an increase and decrease in the composition.An interesting all-optical figure of merit was reported to assess the nanocomposite films for a practical device.It was calculated that the device all-figures of merit were based on the nonlinear response,which is important for the all-optical switching device.The results demonstrate that the optimized all-optical figures of merit can be achieved by adjusting the composition and input laser power,which can be used for the design of different all-photonic devices,and the results of nonlinear switching behavior can open new possibilities for using the nanocomposite films in laser Q-switching and mode-locking.     

Surface studies on bimetallic thiocyanate ligand based single crystals of MnHg(SCN)4, CdHg(SCN)4 and ZnCd(SCN)4

Bimetallic SCN ligand based single crystals of manganese mercury thiocyanate (MMTC), cadmium mercury thiocyanate (CMTC) and zinc cadmium thiocyanate (ZCTC) are grown by slow solvent evaporation technique. The growth mechanism and surface features are investigated by optical microscopic techniques such as scanning electron microscopy (SEM) and atomic force microscopy (AFM). The laser induced surface damage measurements were carried out using a Q-switched Nd:YAG laser at 1064 nm with laser beam of 1.0 Hz and pulse duration 25 ps. The laser damage threshold values of MMTC, CMTC and ZCTC are found to be 15.9, 22.9 and 19.7 GW/cm², respectively. The SEM analysis of MMTC reveals the formation of elongated dendrite growth pattern caused by the fluctuations of Mn and Hg metal ligands when thiocyanate (SCN) bridges them. The etching study indicates the occurrence of different types of etch pit patterns like terraced triangles, pillars, pyramids and rods. The AFM images confirm the formation of three major hillocks with cavities in MMTC. The measured roughness values for CMTC crystal are very much lower than that of MMTC.     

Clustering study in Eu(DBM)3Phen-doped polymer optical fibers by optical properties and near-field scanning microscopy

The clusters of Eu3+ ion in Eu(DBM)3Phen-doped polymethyl methacrylate (PMMA) have been studied by three means. The relative fluorescence intensity ratio of the 5D0 → 7F2 to 5D0 → 7F1 transitions with different concentrations of Eu3+ in Eu(DBM)3Phen-doped PMMA and metastable-state (5D0) lifetime dependence on Eu3+ concentration are analyzed. The analysis indicates that there are no clustering effects in Eu3+ ions of Eu(DBM)3Phen-doped PMMA when the Eu3+ doping concentration is up to 1.0 wt.-%. At the same time, the clustering effect has not been observed by the scanning near-field optical microscopy (SNOM) in Eu(DBM)3Phen-doped PMMA with 1.0 wt.-% of Eu3+ ions. The analysis reveals that a high concentration of Eu3+ can be incorporated into polymer optical fiber (POF) without clustering effect.OCIS codes: 180.5810, 300.6280, 250.5460, 160.5690.     

Laser writing system for fabrication of diffractive optics elements

We report a laser writing system for fabrication of diffractive optical elements with He-Cd laser. The wavelength of the light source is 441.6 nm. The output beam is collimated into parallel light with uniform intensity distribution after passing through the spatial filter with a pinhole of 25μm and the collimating device. A microscopy objective lens with numerical aperture (NA) of 0.65 is used to focus the beam into a small diffraction spot. Any pattern can be written with this system. Experimental results are presented.The written gratings and the phase patterns were verified with a conventional optical microscopy and the Taylor Hobson equipment.     

Unusual Phase Separation Kinetics in Poly(Methyl Methacrylate)/Poly(Styrene-co-Acrylonitrile) (PMMA/SAN) Blends with PMMA of Different Molecular Weights

The influence of molecular weight of poly (methyl methacrylate) (PMMA) on the thermodynamics and dynamics of phase separation in PMMA/poly (styrene-co-acrylonitrile) (SAN) blends was investigated via optical microscopy, time-resolved small-angle light scattering (SALS), and dynamic rheological measurements. It was found that the cloud point temperature of the blends decreased with an increase in the molecular weight of the PMMA. The phase separation rates of PMMA 48K/SAN and PMMA 85K/SAN blends with the near-critical composition were almost the same at small quench depths due to the limited mobility of molecular chains at low temperatures. However, an unexpected phase separation dynamics was observed at larger quench depths. Not only the morphology evolution but also the apparent diffusion coefficient D_app calculated from SALS revealed that the phase separation rate was faster in the PMMA 85K/SAN blend than in the PMMA 48K/SAN blend. The possible reasons for this unusual rapid kinetics of phase separation observed in the higher molecular weight blend were discussed in terms of molecular mobility and viscoelasticity.     

All optical switching in azo-polymer planar waveguide

In this paper all optical switching in planar methyl red doped poly (methyl methacrylate) (MR/PMMA) waveguide and the effects of different parameters on this process are presented. Switching was achieved by a 488 nm Ar ion laser (pump beam) on a 633 nm He-Ne laser (probe beam) when passed through the waveguide. The effect of temperature and pump intensity, polarization and chopping frequency on switching is investigated. The switching process is attributed to trans-cis-trans photoisomerization of azo dyes in the polymer host. By studying the absorption spectrum of the sample, it is shown that both pump and probe laser beams are effective on the switching process.     

Atmospheric turbulence and numerical evaluation of bit error rate (BER) in free-space communication

Bit error rate (BER) is an important parameter in free-space optical (FSO) communication. This paper presents the numerical evaluation of BER by studying the propagation of an initial Gaussian laser beam through turbulent atmosphere. Beam scintillation, spreading and wandering were considered as the atmospheric turbulent effects on the laser beam degradation. Different turbulent conditions and laser beam characteristics were applied to the calculations. The results show that the BER can be influenced considerably by atmospheric turbulence. According to these results the laser beam size and wavelength have also significant effects in the BER values.     

Laser Diode Pumping High-stability 1047 nm TEM_(00) Mode CW Nd: YLiF_4 Laser

1 IntroductionNd: YLF crystal belongs tO the tetragonal syStem with space group 1 4/ a and it isa POSitive single axial crystal in optics. The life-time Of fluorescence of Nd3 ions incaF crystal is lOnger, being 520 us. Therefore, it is a strong candidate for lasermedium of high stored energy and CW lasers. Especially, the therrnai focal distance OfNd: YLF crystal is much longer than that of Nd: YAG crystal and' so the Nd: YLFcrystal is Particularly suitable for a laser in TEWo m…