Effect of surface modification of montmorillonite on the properties of aromatic polyamide/clay nanocomposites

The surface modification of montmorillonite clay was carried out through ion‐ exchange reaction using p‐phenylenediamine as a modifier. This modified clay was employed to prepare aromatic polyamide/organoclay nanocomposite materials. The dispersion behavior of clay was examined in the polyamide matrix. Polyamide chains were synthesized from 4‐aminophenyl sulfone and isophthaloyl chloride (IPC) in dimethylacetamide. These amide chains were suitably end‐capped with carbonyl chloride end groups to interact chemically with modified montmorillonite clay. The resulting nanocomposite films containing 2–20 wt% of organoclay were characterized by TEM, X‐ray diffraction (XRD), thin‐film tensile testing; thermogravimetric analysis (TGA), differential scanning calorimetric (DSC) and water absorption measurements. Mechanical testing revealed that modulus and strength improved up to 6 wt% organoclay loading while elongation and toughness of nanocomposites decreased with the addition of clay content in the matrix. Thermal decomposition temperatures of the nanocomposites were in the range 225–450 °C. These nanocomposites expressed increase in the glass‐transition temperature values relative to pure polyamide describing interfacial interactions among the phases. The percent water uptake of these composites reduced upon the addition of modified layered silicate depicting improved barrier properties. Copyright © 2008 John Wiley & Sons, Ltd.     

One-step water-assisted melt-compounding of polyamide 6/pristine clay nanocomposites: An efficient way to prevent matrix degradation

Polyamide 6 (PA6)/clay nanocomposites, based on organo-modified and pristine (i.e. purified but non-modified) montmorillonite, were prepared using a water-assisted extrusion process based on the injection of water during extrusion. The formation of a single PA6/water phase during extrusion (shown by High Pressure Differential Scanning Calorimetry (HPDSC)) improves the clay dispersion, decreases the PA6 melting temperature by 66 °C (so-called cryoscopic effect), and thus prevents the polymer matrix degradation during processing. This process enables the compounding of pristine clay-based nanocomposites whose dispersion state, thermal and mechanical performances are close to what is generally reported for organo-modified montmorillonite-based nanocomposites. Advantage was taken of water-assisted extrusion to optimize the clay dispersion by increasing shear rate and of the cryoscopic effect to limit the degradation by decreasing the processing temperature. Using these conditions PA6/pristine clay nanocomposites properties are similar to those of more conventional PA6/organomodified clay nanocomposites.     

Morphology and mechanical properties of a novel amorphous polyamide/nanoclay nanocomposite

A novel amorphous polyamide/montmorillonite nanocomposite based on poly(hexamethylene isophthalamide) was successfully prepared by melt intercalation. Wide angle X-ray diffraction and transmission electron microscopy showed that organoclay containing quaternary amine surfactants with phenyl and hydroxyl groups was delaminated in the polymer matrix resulting in well-exfoliated morphologies even at high montmorillonite content. Differential scanning calorimetry results indicated that clay platelets did not induce the formation of a crystalline phase in this amorphous polymer. Tensile tests demonstrated that the addition of nanoclay caused a dramatic increase in Young's modulus (almost twofold) and yield strength of the nanocomposites compared with the homopolymer. The nanocomposites exhibited ductile behavior up to 5 wt % of nanoclay. The improvement in Young's modulus is comparable with semicrystalline aliphatic nylon 6 nanocomposites. Both the main chain amide groups and the amorphous nature of the polyamide are responsible for enhancing the dispersion of the nanofillers, thereby, leading to improved properties of the nanocomposites. The structure-property relationship for these nanocomposites was also explored. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2605–2617, 2008     

Investigating the structure–property relationship of aromatic–aliphatic polyamide/layered silicate hybrid films

Surface treated montmorillonite was used to prepare nanocomposites with aromatic–aliphatic polyamide by solution intercalation technique. The polyamide chains were produced through polycondensation of 4-aminophenyl sulfone with sebacoyl chloride in dimethyl acetamide. Compatibility between the polymer and organoclay was achieved through carbonyl chloride end-capped amide chains prepared by adding extra sebacoyl chloride near the end of polymerization reaction. The nanocomposites morphology and clay dispersion were investigated by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Delaminated and intercalated morphologies were observed for different loading of organoclay. Tensile strength and modulus improved for nanocomposites with optimum organoclay content (10-wt.%). Thermal stability and glass transition temperature of nanocomposites increased relative to pristine polyamide with augmenting organoclay content. Water uptake of these materials decreased as compared to the neat polyamide indicating reduced permeability.     

Clay‐reinforced polyamide: Preferential orientation of the montmorillonite sheets and the polyamide crystalline lamellae

Intercalated and exfoliated nanocomposites were prepared by the extrusion and injection of polyamide‐6 and highly swollen or slightly swollen montmorillonite, respectively. The microstructure of pure compounds was characterized. The basal spacing was more homogeneous in swollen montmorillonite than in nontreated montmorillonite. This was attributed to the presence of a surfactant. Surfactant crystallites were observed in swollen montmorillonite and in the nanocomposites. Their distribution is discussed. The nanocomposites exhibited anisotropic properties attributed to the orientation of the montmorillonite sheets. The preferential orientation of the montmorillonite sheets was studied in detail by small‐angle X‐ray scattering (SAXS). It was found to be related to the injection direction. An average distance between two sheets was also measured from the SAXS spectra. The crystallographic state of the polyamide matrix was then analyzed. The orientation of the polymer lamellae relative to the montmorillonite sheets is discussed. The orientation of the montmorillonite sheets and the polyamide lamellae is expected to play a major role in the mechanical properties of nanocomposites. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1360–1370, 2001     

Study of nylon 66–clay nanocomposites via condensation polymerization

Nylon 66–clay (polyamide 66 (PA66)–organophilic montmorillonite (OMT)) exfoliated nanocomposites were synthesized based on nylon 66 salt and organoclay (OMT) modified by hydro-aminocaproic acid via condensation polymerization. And the nanocomposites were characterized by X-ray diffraction and transmission electronic microscopy. Exfoliated morphology with different clay content was obtained. The effects of cation exchange capacity and organic modified agent of OMT on the formation of exfoliated nanocomposites were investigated. It was shown that only suitable cation exchange capacity and organic modified agent could result in the formation of exfoliated morphology under the condition of condensation polymerization. The thermal and flammability properties of the nanocomposites were investigated through thermogravimetry and cone calorimetry experiments. Results indicate that the exfoliated nanocomposites have enhanced thermal stability and flame retardant properties compared with pure PA66.     

COMPARISON OF POLYAMIDE 66/MONTMORILLONITE NANOCOMPOSITES PREPARED FROM POLYAMIDE 6 AND POLYAMIDE 66 BASED MASTER-BATCHES

Two master-batches,polyamide 66 (PA66)/organo-montmorillonite (OMMT) and polyamide 6 (PA6)/OMMT, prepared by melt compounding with methyl methacrylate (MMA) as co-intercalation agent,have been used to prepare nearly exfoliated PA661montmorillonite (MMT) nanocomposites.The resulting nanocomposites are compared in view of their morphology and properties.Nano-scale dispersion of OMMT is realized in both types of nanocomposites,as revealed by XRD,TEM and Molau tests.PA66/MMT nanocomposites having superior me...     

SMA/蒙脱石纳米复合材料增容PA6/ABS共混体系

采用原位插层法制备苯乙烯-马来酸酐交替共聚物/蒙脱石(SMA/MMT)纳米复合材料增容PA6/ABS共混体系,并与SMA及MMT的增容效果进行比较,运用TEM、SEM、DSC及XRD研究了增容剂SMA/MMT及MMT的增容机理.结果表明,采用SMA做增容剂,体系机械性能下降;MMT可使体系拉伸强度提高,但冲击强度下降;采用SMA/MMT纳米复合材料做为增容剂,可提高共混体系的强度及韧性.TEM、XRD、DSC及SEM研究结果表明,PA6/ABS/(SMA-MMT)体系中MMT主要分布于两相界面处,ABS及PA6分子链可进入MMT层间,形成类似于共聚物结构,起到增容剂的作用,从而降低分散相粒径,增加两相界面作用力,有利于体系力学性能的提高.PA6/ABS/MMT体系中MMT主要分布于连续相PA6中,虽然对分散相粒径影响较小,但增强了PA6相强度,使得体系力学性能提高.     

聚酰胺6/粘土纳米复合材料结晶行为研究进展

由于粘土的异相成核作用以及硅酸盐片层间形成的纳米受限空间,使聚酰胺6,粘土纳米复合材料（PA6CN）的结晶行为与纯聚酰胺6（PA6）相比,有着很大的差别,其结晶行为和影响因素倍受关注。本文着重从PA6CN结晶行为的基本特征、热处理、成型加工和结晶动力学等四个方面对PA6CN的结晶行为进行了综述。     

Structure Analysis of PVC Nanocomposites

In this paper poly(vinyl chloride)/clay nanocomposites were prepared by melt intercalation using a single screw extruder. Problems with thermal stability of these nanocomposites during compounding were largely eliminated by pre-treatment of the organoclay with plasticizer (dioctyl phthalate), which created a barrier between polymer and quaternary amine. These nanocomposite materials were analyzed with respect to their morphology. The intercalation, exfoliation, nano-phase dispersion and orientation were investigated using Transmission Electron Microscopy (TEM), Scanning Electron Microscopy (SEM), Atomic Force Microscopy (AFM) and X-ray diffraction (XRD). Moreover, different types of sample preparation for these techniques were tested as well. It was found that partially intercalated and disordered structure arose in poly (vinyl chloride) composites containing sodium type of montmorillonite, while a fine dispersion of partial to nearly full exfoliation of individual montmorillonite layers in poly (vinyl chloride) matrix was observed when this clay was organically modified. Finally, the influence of different mixing time (in extruder) on nano-phase morphology was surveyed.     

Polymorphic behavior in syndiotactic polystyrene/clay nanocomposites

X‐ray diffraction methods were used in an investigation of the structural changes in syndiotactic polystyrene (sPS)/clay nanocomposites. sPS/clay was prepared by the intercalation of sPS polymer into layered montmorillonite. Both X‐ray diffraction data and transmission electron microscopy micrographs of sPS/clay nanocomposites indicated that most of the swellable silicate layers were exfoliated and randomly dispersed in the sPS matrix. The X‐ray diffraction data also showed the presence of polymorphism in the sPS/clay nanocomposites. This polymorphic behavior was strongly dependent on the thermal history of the sPS/clay nanocomposites from the melt and on the content of clay in the sPS/clay nanocomposites. Quenching from the melt induced crystallization into the α‐crystalline form, and the addition of montmorillonite probably increased heterophase nucleation of the α‐crystalline form. The effect of the melt crystallization of sPS and sPS/clay nanocomposites at different temperatures on the crystalline phases was also examined. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 736–746, 2002     

Preparation and properties of aramid/layered silicate nanocomposites by solution intercalation technique

Polymer—clay nanocomposites were synthesized from aromatic polyamide and organoclay using the solution intercalation technique. Polyamide chains were produced through the reaction of 4,4′‐oxydianiline (ODA) and isophthaloyl chloride (IPC) in N, N′‐dimethyl acetamide, using stoichiometry yielding chains with carbonyl chloride end groups. The intercalation of sodium montmorillonite (Na‐MMT) was carried out using p‐phenylene diamine as a swelling agent through an ion exchange reaction. Different concentrations of organoclay were blended with the polyamide solution for complete dispersion of clay throughout the matrix. The resulting composite films were characterized by X‐ray diffraction (XRD), transmission electron microscopy (TEM), mechanical testing, thermogravimetry (TGA), differential scanning calorimetry (DSC) and water absorption measurements. The XRD pattern and morphology of the nanocomposites revealed the formation of exfoliated and intercalated clay platelets in the matrix. The film containing a small amount of clay was semitransparent and had a tensile strength of the order of 70 MPa (relative to the 52 MPa of the pure aramid). Thermal decomposition temperatures were in the range of 300–450°C and the weight of the samples remaining after heating to 900°C was found to be roughly proportional to the clay loading. DSC showed a systematic increase in the glass transition temperature with increase in clay content. Water absorption of the pristine aramid film was rather high (5.7%), which reduced upon loading of organoclay. Copyright © 2008 John Wiley & Sons, Ltd.     

Maleic Anhydride Polyethylene Octene Elastomer Toughened Polyamide 6/Polypropylene Nanocomposites: Mechanical and Morphological Properties

A series of polyamide 6/polypropylene (PA6/PP) blends and nanocomposites containing 4 wt% of organophilic modified montmorillonite (MMT) were designed and prepared by melt compounding followed by injection molding. Maleic anhydride polyethylene octene elastomer (POEgMAH) was used as impact modifier as well as compatibilizer in the blend system. Three weight ratios of PA6/PP blends were prepared i.e. 80:20, 70:30, and 60:40. The mechanical properties of PA6/PP blends and nanocomposite were studied through flexural and impact properties. Scanning electron microscopy (SEM) was used to study the microstructure. The incorporation of 10 wt% POEgMAH into PA6/PP blends significantly increased the toughness with a corresponding reduction in strength and stiffness. However, on further addition of 4 wt% organoclay, the strength and modulus increased but with a sacrifice in impact strength. It was also found that the mechanical properties are a function of blend ratio with 70:30 PA6/PP having the highest impact strength, both for blends and nanocomposites. The morphological study revealed that within the blend ratio studied, the higher the PA6 content, the finer were the POEgMAH particles.     

Synthesis of Biodegradable Polycaprolactone/Montmorillonite Nanocomposites by Direct In-situ Polymerization Catalysed by Exchanged Clay

Poly (e-caprolactone) (PCL) layered silicate nanocomposites have the advantage adding biocompatibility and biodegradability to the traditional properties of nanocomposites. They can be prepared by in situ ring-opening polymerization of e-caprolactone using conventional initiator to induce polymerization in the presence of an organophilic clay, such as organomodified montmorillonite. In this work, we have used an alternative method to prepare poly(e-caproilactone)/montmorillonite nanocomposites. The cationic polymerization of e -caprolactone was initiated directly by Maghnite-TOA, organomodified montmorillonite clay, to produce nanocomposites. Resulted nanocomposites were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), force atomic microscopy (AFM) and thermogravimetry. The evolution of mechanical properties was also studied. Corrected by: Correction: Synthesis of Biodegradable Polycaprolactone/Montmorillonite Nanocomposites by Direct In-situ Polymerization Catalysed by Exchanged Clay Vol. 247, Issue 1, page n/a, Article first publshed online: 1 AUG 20111; DOI 10.1002/masy.200750150     

Thermal and mechanical properties of PE/organoclay nanocomposites

Polyethylene/montmorillonite clay nanocomposites were obtained via direct melt intercalation. The clay was organically modified with four different types of quaternary ammonium salts. The objective of this work is to study the use of montmorillonite clay in the production of nanocomposites by means on rheological, mechanical and crystallization properties of nanocomposites and to compare to the properties of the matrix and PE/unmodified clay nanocomposites. In general, the tensile test showed that the yield strength and modulus of the nanocomposites are close to the pure PE. Apparently, the mixture with Dodigen salt seems to be more stable than the pure PE and PE/unmodified clay.     

Polyamide‐6/natural clay mineral nanocomposites prepared by solid‐state shear milling using pan‐mill equipment

The polyamide‐6 (PA6)/natural clay mineral nanocomposites were successfully prepared by solid‐state shear milling method without any treatment of clay mineral and additives. PA6/clay mixture was pan‐milled to produce PA6/clay compounding powder, using pan‐mill equipment. The obtained powder as master batch was diluted with neat PA6 to prepare composites by a twin‐screw extruder. The clay silicate layers were found to be partially exfoliated and dispersed homogeneously at nanometer level in PA6 matrix. The rheological measurements and mechanical properties of nanocomposites were characterized. The shear viscosities of nanocomposites were higher than that of pure PA6, and tensile strength and tensile modulus increased, but Izod impact strength decreased, with increasing concentration of clay. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 249–255, 2006     

Preparation of polylactic acid/epoxidized palm oil/fatty nitrogen compounds modified clay nanocomposites by melt blending

In this study, new biopolymer nanocomposites have been prepared. Fatty nitrogen compounds (FNCs); fatty amide (FA), fatty hydroxamic acid (FHA), and carbonyl difatty amide (CDFA), which were synthesized from palm oil, have been used as one of organic compounds to modify natural clay (sodium montmorillonite). The clay modification was carried out by stirring the clay particles in an aqueous solution of FA, FHA, and CDFA by which the clay layer distance increases from 1.23 to 2.71, 2.91 and 3.23 nm, respectively. The modified clay was then used in the preparation of the polylactic acid/epoxidized palm oil (PLA/EPO) blend nanocomposites. The interaction of the modifier in the clay layer was characterized by X-ray diffraction (XRD), and Fourier transform infrared (FTIR). Elemental analysis was used to estimate the presence of FNCs in the clay. The nanocomposites were synthesized by melt blending of the modified clay and PLA/EPO blend at the weight ratio of 80/20. The nanocomposites were then characterized using XRD, transmission electron microscopy (TEM), thermogravimetric analysis (TGA), and tensile properties measurements. The XRD and TEM results confirmed the production of nanocomposites. PLA/EPO modified clay nanocomposites show higher thermal stability and significant improvement of mechanical properties in comparison with those of the PLA/EPO blend.     

Preparation of poly(propylene)/clay layered nanocomposites by melt intercalation from pristine montmorillonite (MMT)

Poly(propylene)/clay nanocomposites were prepared by melt intercalation, using pristine montmorillonite (MMT), hexadecyl trimethyl ammonium bromide (C16), poly(propylene) (PP) and maleic acid (MA) modified PP (MAPP), The nanocomposites structure is demonstrated using X‐ray diffraction (XRD) and high resolution electronic microscopy (HREM). Our purpose is to provide a general concept for manufacturing polymer nanocomposites by melt intercalation starting from the pristine MMT. We found different kneaders (twin‐screw extruder or twin‐roll mill) have influence on the morphology of the PP/clay nanocomposites. Thermogravimetric analysis (TGA) shows that the thermal stability of PP/clay nanocomposites has been improved compared with that of pure PP. Copyright © 2003 John Wiley & Sons, Ltd.     

Influence of clay modification on the properties of aramid-layered silicate nanocomposites

Nanocomposites from organoclay and aromatic polyamide were prepared using solution intercalation method. Aramid chains were synthesised by reacting 4-aminophenylsulfone with isophthaloyl chloride in dimethylacetamide. Dodecylamine was used as a modifier to change the hydrophilic nature of montmorillonite into organophilic. Suitable quantities of organoclay were mixed in the aramid solution with high-speed stirring for homogeneous dispersion of the clay. Thin films cast from these materials after evaporating the solvent were characterised. The morphology of nanocomposites was determined by X-ray diffraction and TEM. Results revealed the formation of delaminated and disordered intercalated clay platelets in the aramid matrix. Mechanical data indicated improvement in the tensile strength and modulus with clay loading up to 6 wt.%. The glass transition temperature increased up to 20 wt.% organoclay, suggesting better cohesion between the two phases and thermal stability augmented with increasing clay loading. The water uptake reduced gradually as a function of organoclay showing decreased permeability.     

Evaluation of ammonium terminated PMMA as compatibilizers for monomer casting polyamide6/clay nanocomposites

The compatibilization effects provided by ammonium terminated PMMA(PMMA‐t‐NH₃⁺) on monomer casting polyamide6 (MCPA6)/clay(pristine sodium montmorillonite) nanocomposites were studied in this article. PMMA‐t‐NH₃⁺ used in this study was prepared by radical polymerization using 2‐aminoethanethiol hydrochloride as chain transfer agent. MCPA6/clay/PMMA‐t‐NH₃⁺ nanocomposites were prepared by in situ anionic ring‐opening polymerization of ε‐caprolactam. X‐ray diffraction and transmission electron microscopy plus rheological measurement were used to characterize those nanocomposites. The results indicated that PMMA‐t‐NH₃⁺ would be a good compatibilizer for this system. With PMMA‐t‐NH₃⁺ content increasing, a better dispersion of clay was successfully achieved in the MCPA6 matrix. Furthermore, analysis using differential scanning calorimetry indicated that well dispersed clay layers limited the mobility of the MCPA6 molecule chains to crystallize, reduce the crystalline degree, and favor the formation of the γ‐crystalline form of the MCPA6 matrix. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1802–1810, 2008