The concentrations and exposure doses of radon and thoron in residences of the rural areas of Kosovo and Metohija

This paper deals with the results of indoor radon and thoron concentrations and exposure doses obtained for 63 dwellings out of the 14 rural communities of Central Kosovo, North Kosovo and Prizren region. These research activities are part of overall radiological research that has systematically been carried out since 1986, particularly in Kosovo and Metohija regions. Passive radon/thoron discriminative detectors, exposed for three months, were used. The arithmetic mean concentrations of indoor radon and thoron are C_Rn = 429 Bq m^?3 C_Tn = 85 Bq m^?3.     

Seasonal indoor radon concentration in FYR of Macedonia

This paper presents the results of the seasonal indoor radon concentration measurements in dwellings in all regions of the Former Yugoslav Republic (FYR) of Macedonia. The measurements were made in 437 dwellings using CR-39 track detectors over four successive three-month periods (winter, spring, summer and autumn) throughout 2009. The results of analysis of variance showed statistically significant differences between indoor radon concentrations in different seasons. The geometric mean values and geometric standard deviations of indoor radon concentrations in winter, spring, summer and autumn were obtained to be: 115 Bq m^?3 (2.02), 72 Bq m^?3 (1.97), 46 Bq m^?3 (1.95), 92 Bq m^?3 (2.02), respectively. The geometric mean values of spring, summer and autumn to winter ratios were found to be: 0.63 (1.50), 0.40 (1.81), and 0.80 (1.58), respectively. The results of the analysis of the variance showed statistically significant differences among the indoor radon measurements for the regions in different seasons. The influence of the factors linked to building characteristics in relation to radon measurements in different seasons was examined. The factors which enable a differentiation into subgroups (significance level p < 0.05) are the floor level, basement and building materials.     

Exposure to indoor radon and natural gamma radiation in public workplaces in north-western Greece

Measurements of indoor radon levels and gamma dose rates were performed in 42 workplaces in Ioannina, north-western Greece. Radon concentrations followed a log-normal distribution with an arithmetic mean of 95 ± 51 Bq m^?3. In all cases, radon levels were below 400 Bq m^?3, which is the action level implemented by the Greek Regulation for Radiation Protection, in accordance with the European Commission recommendation. Comparing summer and winter measurements, no statistically significant seasonal variation was established. However, radon concentrations measured in basement and ground floor workplaces were significantly higher (p < 0.01) than those measured in the first and upper floors. Annual effective dose rates from inhalation of radon and its decay products were estimated to be in the range from 0.13 to 1.36 mSv y^?1 with a mean value of 0.62 mSv y^?1. Indoor exposure to natural gamma radiation entailed an average effective dose rate of 0.13 mSv y^?1, of which approximately 62% was due to terrestrial and the rest due to cosmic sources. The reported data contribute to the assessment of radon distribution and dose estimate at the national level.     

Radon concentrations in schools of the Neapolitan area

A radon survey was carried out in 30 schools located in the metropolitan area around Naples, Italy. Radon concentration was measured using the SSNTD (Solid State Nuclear Track Detectors) method with LR115 detectors. Time integrated measurements covered two consecutive 6-month periods at different locations inside the school buildings: classrooms, laboratories and offices. Data distribution is well fitted by a log-normal curve. The arithmetic mean annual radon concentration is 144 Bq m⁻³, the geometric mean is 86 Bq m⁻³; the standard deviations are respectively 7 Bq m⁻³ and 3. The fractions of rooms where radon concentrations exceed the reference levels of 200, 400 and 500 Bq m⁻³ are 21.3%, 7.6% and 4.5% respectively.The results show that radon concentration in scientific laboratories and in offices is higher than in classrooms.     

Systematic grid-wise radon concentration measurements and first radon map in Cyprus

A systematic study of the indoor airborne radon concentration in the central part of the Nicosia district was conducted, using high-sensitivity active radon portable detectors of the type “RADIM3A”. From a total of 108 measurements in 54 grids of 1 km² area each, the overall mean value is 20.6 ± 13.2 Bq m^?3 (A.M. ± S.D.). That is almost twice less than the corresponding average worldwide value. The radon concentration levels in drinking water were also measured in 24 sites of the residential district, using the high-sensitivity radon detector of the type “RADIM3W”. The mean value obtained from these measurements is 243.8 ± 224.8 mBq l^?1, which is relatively low compared to the corresponding internationally accepted level. The associated annual effective dose rates to each measurement were also calculated and compared to the corresponding worldwide values. From the geographical coordinates of the measuring sites and the corresponding radon concentration values, the digital radon map of the central part of the Nicosia district was constructed for the first time, by means of the ArcMap software package.     

Measuring radon flux across active faults: Relevance of excavating and possibility of satellite discharges

Searching for gas exhalation around major tectonic contacts raises important methodological issues such as the role of the superficial soil and the possible long distance transport. These effects have been studied on the Xidatan segment of the Kunlun Fault, Qinghai Province, China, using measurement of the radon-222 and carbon dioxide exhalation flux. A significant radon flux, reaching up to 538 ± 33 mBq m^?2 s^?1 was observed in a 2–3 m deep trench excavated across the fault. On the soil surface, the radon flux varied from 7 to 38 mBq m^?2 s^?1, including on the fault trace, with an average value of 14.1 ± 1.0 mBq m^?2 s^?1, similar to the world average. The carbon dioxide flux on the soil surface, with an average value of 12.9 ± 3.3 g m^?2 day^?1, also remained similar to regular background values. It showed no systematic spatial variation up to a distance of 1 km from the fault, and no clear enhancement in the trench. However, a high carbon dioxide flux of 421 ± 130 g m^?2 day^?1 was observed near subvertical fractured phyllite outcrops on a hill located about 3 km north of the fault, at the boundary of the large-scale pull-apart basin associated with the fault. This high carbon dioxide flux was associated with a high radon flux of 607 ± 35 mBq m^?2 s^?1. These preliminary results indicate that, at the fault trace, it can be important to measure gas flux at the bottom of a trench to remove superficial soil layers. In addition, gas discharges need to be investigated also at some distance from the main fault, in zones where morphotectonics features support associated secondary fractures.     

Natural radioactivity and human exposure by raw materials and end product from cement industry used as building materials

During the manufacturing process in the cement industry, raw materials of different levels of natural radioactivity are utilized. In this study we present the radiological impact of cements as a building material and the different raw materials used in their manufacture. A total of 218 samples of raw materials and their end product cements were collected from the cement industry of Macedonia (The Former Yugoslav Republic) during the period 2005–2007. The specific activities, evaluated by gamma spectrometry analysis, showed the highest mean specific activity in fly ash (²²⁶Ra, 107 ± 45 Bq kg^?1; ²³²Th, 109 ± 30 Bq kg^?1; ⁴⁰K, 685 ± 171 Bq kg^?1), which is used as a raw material. However, the final cement product usually has relatively lower activity compared with the activity of the raw material and the mean specific activity of the final cement products were lower (²²⁶Ra, 42 ± 10 Bq kg^?1; ²³²Th, 28 ± 6 Bq kg^?1; ⁴⁰K, 264 ± 50 Bq kg^?1). The radium equivalent activity and the hazard index were calculated for each sample to assess the radiation hazard. The mean annual effective dose originating from the cements was found to be 111 ± 22 μSv y^?1, which is below the recommended EC limit of 300 μSv y^?1.     

About ageing and fading of Cr-39 PADC track detectors used as air radon concentration measurement devices

PADC detectors are widely used as air radon concentration measurement devices and the typical procedure that a Radon Service Laboratory uses to manage the detectors provides a calibration phase followed by the field measurement. The calibration is performed in a reference radon concentration atmosphere, using high radon concentration values in order to achieve typical exposure values of few MBq h m^?3 with an exposure time of few days. On the other hand the field measurement is characterized by long term exposures lasting up to six months and by radon concentrations that are quite lower than the ones used in the calibration.The aim of this study is to check whether the calibration procedure is actually representative of a field measurement, or, in other words, whether and how much ageing or fading can affect the calibration factor.We found that the ageing and fading effect can produce a decrease in the detector sensitivity leading to an underestimation of the radon concentration up to 40% for exposure lasting few months. An important issue is that both ageing and fading can be ascribed to a decrease in the track etching velocity V_t.In the paper we also provide an algorithm to compensate for the sensitivity variation due to fading/ageing effect.     

Radiological impacts of natural radioactivity from phosphogypsum piles in Huelva (Spain)

The activity concentrations of ²²⁶Ra, ²³²Th and ⁴⁰K have been measured by gamma spectroscopy in samples of soil collected from the different zones of around Huelva (Spain). The average activity concentrations of ²²⁶Ra (Bq kg^?1) in the active phosphogypsum (PG) stacks, unrestored and restored zones were 647, 573 and 83 respectively. The corresponding values for ²³²Th and ⁴⁰K (Bq kg^?1) were 8, 10 and 25 and 33, 47 and 225 respectively. As a measure of radiation hazard to the occupational workers and public, the Ra equivalent activities, representative level index and dose rates due to natural radionuclides at 1 m above the ground surface were estimated. The average of absorbed dose rates due to ²²⁶Ra, ²³²Th and ⁴⁰K (nGy/h) from active PG stacks, unrestored and restored zones are 284, 255 and 55.The calculated external γ-radiation average dose (mSv/y) received by the workers of the phosphogypsum piles are estimated to be 0.293, 0.262 and 0.057 which is far below the international agreed dose limit of 20 mSv/y (ICRP-60, 1990) for workers. Also, the radiation dose to a member of the public resulting from the use of PG is negligible compared to the average annual effective dose from natural sources (2.4 mSv/y).     

Lipase catalyzed ultrasonic synthesis of poly-4-hydroxybutyrate-co-6-hydroxyhexanoate

Four different lipases were compared for ultrasound-mediated synthesis of the biodegradable copolymer poly-4-hydroxybutyrate-co-6-hydroxyhexanoate. The copolymerization was carried out in chloroform. Of the enzymes tested, Novozym 435 exhibited the highest copolymerization rate, in fact the reaction rate was observed to increase with about 26-fold from 30 to 50 °C (7.9 × 10^?3 M s^?1), sonic power intensity of 2.6 × 10³ W m^?2 and dissipated energy of 130.4 J ml^?1. Copolymerization rates with the Candida antarctica lipase A, Candida rugosa lipase, and Lecitase Ultra? were lower at 2.4 × 10^?4, 1.3 × 10^?4 and 3.5 × 10^?4 M s^?1, respectively. The catalytic efficiency depended on the enzyme. The efficiency ranged from 4.15 × 10^?3 s^?1 M^?1 for Novozym 435–1.48 × 10^?3 s^?1 M^?1 for C. rugosa lipase. Depending on the enzyme and sonication intensity, the monomer conversion ranged from 8.2% to 48.5%. The sonication power, time and temperature were found to affect the rate of copolymerization. Increasing sonication power intensity from 1.9 × 10³ to 4.5 × 10³ W m^?2 resulted in an increased in acoustic pressure (P_a) from 3.7 × 10⁸ to 5.7 × 10⁸ N m^?2 almost 2.4–3.7 times greater than the acoustic pressure (1.5 × 10⁸ N m^?2) that is required to cause cavitation in water. A corresponding acoustic particle acceleration (a) of 9.6 × 10³–1.5 × 10⁴ m s^?2 was calculated i.e. approximately 984–1500 times greater than under the action of gravity.     

Radon activity measurements around Bakreswar thermal springs

²²²Rn concentrations were measured in the bubble gases, spring waters, soil gases and in ambient air around the thermal springs at Bakreswar in West Bengal, India. This group of springs lies within a geothermal zone having exceptionally high heat flow about 230 mW/m², resembling young oceanic ridges. The spring gas has a high radon activity (～885 kBq/m³) and is rich in helium (～1.4 vol. %) with appreciably large flow rate. The measured radon exhalation rates in the soils of the spring area show extensive variations from 831 to 4550/mBqm² h while ²²²Rn concentrations in the different spring waters vary from 3.18 to 46.9 kBq/m³. Surface air at a radius of 40 m around the springs, within which is situated the Bakreswar temple complex and a group of dwellings, has radon concentration between 450 and 500 Bq/m³. In the present paper we assess the radon activity background in and around the spring area due to the different contributing sources and its possible effect on visiting pilgrims and the people who reside close to the springs.     

EPR and UV spectroscopic investigations of sucrose irradiated with heavy-ion particles

Crystalline sucrose irradiated with C and Si ions is investigated with EPR and UV spectroscopy. Samples are treated at different doses of radiation in the region 20–300 Gy and linear energy transfer (LET) values of 39.6, 49 and 58 keV μm^?1 for C ions and 60 keV μm^?1 for Si ions. All samples exhibit identical EPR spectra due to radiation-induced stable sucrose radicals. At given constant LET the EPR signal responses are linear to the absorbed doses of Si and C ions. Water solutions of irradiated sucrose exhibit UV absorption maximum at 267 nm due to the product of radical recombination. The intensity of this band is stronger at irradiation with Si than with C ions. UV absorption is more sensitive to heavy-ion species irradiation than the EPR signals.     

Difficulties in the dose estimate of workers originated from radon and radon progeny in a manganese mine

The regulation of radon concentration at workplaces has gained an accentuated importance in all countries. Nevertheless, at this time there is no globally accepted workplace protocol that sets out safe radon concentration values.In this study the radon concentration measured during the working hours and the equilibrium factor, which are necessary for the exact estimation of the radiation dose originating from radon and effecting manganese miners are determined in a Hungarian manganese mine. In order to determine the exact committed effective dose, workers wore track-etched radon.The annual average radon concentration measured at the different points in the mine that was investigated may vary by ±30% relative to the average of the total of the measurement points. The influence of the measurement period is even more significant as the difference related to the annual average may be ±30% with a measurement period of 6 months. The radon concentration level measured during working hours was approximately half of the average measured during the whole period. The measured equilibrium factor was 50% greater than the value given in literature. Disregarding any of these factors may lead to significant errors for the estimation of dose to workers.The average value of the estimated effective radiation dose was 3.7 mSv year⁻¹ based on the personal radon dosimeters.     

Analysis and risk estimates to workers of Brazilian granitic industries and sandblasters exposed to respirable crystalline silica and natural radionuclides

Occupational exposure to respirable crystalline silica and to radiation emitted by natural radionuclides present both in rocks and sands was studied in the Brazilian extractive process and granite product manufacture. Respirable airborne dust samples were collected in working environments, where workers perform different tasks with distinct commercial granites types, and also in places where sandblasters work with sands from different origins. The free crystalline silica contents were determined using X-ray diffraction of the respirable particulate fraction of each sample. Dust samples from granite cutting and sandblasting ambient had the natural radionuclides concentrations measured by gamma spectrometry. Dust concentrations in the workplaces were quite variable, reaching values up to 10 times higher than the respirable particle mass threshold limit value (TLV) set by the American Conference for Governmental Industrial Hygienists of 3 mg m^?3. Also the free crystalline silica concentrations were high, reaching values up to 48 times the TLV of 0.025 mg m^?3. Additionally, our results suggest that the risk of radiation-induced cancer in the granite or marble industries is negligible. However, the combined exposure to dust, gamma radiation, and radon daughter products could result in the enhancement of lung cancer risks associated to sandblasting activities.     

Adsorption and desorption characteristics of 3-dimensional networks of fused graphene

Here we explore the exceptional structural characteristics of a set of graphene-related materials prepared by a wet chemical approach. We present a comprehensive study of the effects of morphology, sonication, temperature, probe species, and stacking behaviour on the measurement of graphene surface area. Nitrogen gas was used in the solid state gas adsorption measurements and methylene blue dye for adsorption measurements on aqueous dispersions of graphene. The surface area values obtained are among the highest reported for synthetic graphenes: 1700 m² g^? 1 in aqueous dispersions and 612 m² g^? 1 in the solid state. Microscopy revealed the graphene used in the study was present in large part as free sheets and electron diffraction confirmed the successful synthesis of high quality graphene with a regular C–C bond length of 1.41 ± 0.02 Å.     

The use of soil gas as radon source in radon chambers

A procedure is described in which soil gas is utilized as an alternative to the ²²⁶Ra source for the supply of the radon gas required to fill a radon chamber where radon-measuring devices are calibrated. The procedure offers opportunities to vary the radon concentration within the chamber around an average value of about 500 Bq/m³, which is considered to be sufficient for calibrating indoor radon detectors. The procedure is simple and the radon source does not require radiation protection certification (for import and/or use), unlike the commercially produced standard radioactive (²²⁶Ra) sources.     

Birefraction of the LiNbO3 crystal in the infrared band

We proposed a spectrum method to determine birefraction of the sample. When the infrared incident light transmits in the birefraction direction of the cube crystal, because of the birefraction of the sample, the transmit spectrum appears interference fringes. The equation Δn = 1/[D(dυ/dm)] shows the relationship between the birefraction and the wave-number, with the interference-number of crystals in the infrared band at room temperature. Via the infrared transmitting along the x-axis of cube lithium niobate crystal, the interference fringes were found. By the fitted polynomial method, the relationship of the birefraction and the wave-number or wavelength of the lithium niobate crystal be educed, which is, Δn = 0.4149 ? 9.00174 × 10^?5υ + 5.64347 × 10^?9υ²,or n = 0.05366 ? 5.20334 × 10^?5λ + 3.99694 × 10^?8λ².     

Fiber curvature sensor based on spherical-shape structures and long-period grating

A novel curvature sensor based on optical fiber Mach–Zehnder interferometer (MZI) is demonstrated. It consists of two spherical-shape structures and a long-period grating (LPG) in between. The experimental results show that the shift of the dip wavelength is almost linearly proportional to the change of curvature, and the curvature sensitivity are −22.144 nm/m⁻¹ in the measurement range of 5.33–6.93 m⁻¹, −28.225 nm/m⁻¹ in the range of 6.93–8.43 m⁻ and −15.68 nm/m⁻¹ in the range of 8.43–9.43 m⁻¹, respectively. And the maximum curvature error caused by temperature is only −0.003 m⁻¹/°C. The sensor exhibits the advantages of all-fiber structure, high mechanical strength, high curvature sensitivity and large measurement scales.     

Preparation of enzyme nanoparticles and studying the catalytic activity of the immobilized nanoparticles on polyethylene films

Using high-intensity ultrasound, in situ generated α-amylase nanoparticles (NPs) were immobilized on polyethylene (PE) films. The α-amylase NP-coated PE films have been characterized by E-SEM, FTIR, DLS, XPS and RBS. The PE was reacted with HNO₃ and NPs of the α-amylase were also deposited on the activated PE. The PE impregnated with α-amylase (4 μg per 1 mg PE) was used for hydrolyzing soluble potato starch to maltose. The immobilization improved the catalytic activity of α-amylase at all the reaction conditions studied. The kinetic parameters, K_m (5 and 4 g L^?1 for the regular and activated PE, respectively) and V_max (5 × 10^?7 mol ml^?1 min^?1, almost the same numbers were obtained for the regular and activated PEs) for the immobilized amylase were found to slightly favor the respective values obtained for the free enzyme (K_m = 6.6 g L^?1, V_max = 3.7 × 10^?7 mol ml^?1 min^?1). The enzyme remained bound to PE even after soaking the PE in a starch solution for 72 h and was still found to be weakly active.     

Third order nonlinear optical properties of ethyltriphenylphosphonium bis(2-thioxo-1,3-dithiole-4,5-dithiolato)aurate (III)

A novel organometallic compound, ethyltriphenylphosphonium bis(2-thioxo-1,3-dithiole-4,5-dithiolato)aurate (III), abbreviated as TPEPADT, was synthesized. The TPEPADT doped poly(methyl methacrylate) (PMMA) thin film with a mass fraction of 1% (1 wt.%) was prepared by using a spin-coating method. The third-order nonlinear optical properties of TPEPADT in acetonitrile solution and TPEPADT-doped PMMA thin film were investigated by using the laser Z-scan technique at the wavelength 1064 nm with laser duration of 20 ps. The linear refractive index of the polymer thin film was also studied. The Z-scan curves revealed that both TPEPADT in acetonitrile solution and the polymer thin film possessed negative nonlinear refraction, exhibiting a self-defocusing effect and nonlinear absorption was negligible under the experimental conditions used. The nonlinear refractive index was calculated to be ?1.9 × 10^?18 m²/W for TPEPADT in acetonitrile solution and ?8.9 × 10^?15 m²/W for the polymer thin film. These results suggest that TPEPADT have potential for the application of all-optical switching devices.