Characterization and demulsification of produced liquid from weak base ASP flooding

Weak base alkali-surfactant-polymer (ASP) flooding technology has been applied in Daqing oilfield to enhance oil recovery. The effects of ASP on the characteristics of oil droplets in produced liquid were investigated. Surfactant can decrease interfacial tension (IFT) and zeta potential, making main contribution to the stability of oil droplets. Weak alkali (Na₂CO₃) can decrease IFT and polymer can decrease zeta potential, resulting in stable oil droplets in produced liquid. The produced liquid from weak base ASP flooding is easier to treat than that from strong base ASP flooding. A mixed demulsifier GFD410-8 was prepared and used to enhance oil–water separation in produced liquid. When the demulsifier dose of 50 mg/kg was used to demulsify the simulated produced liquid with the concentrations of alkali 2000 mg/kg, surfactant 600 mg/kg and polymer 600 mg/kg, water volume and water content after 30 min settling were less than 30% and 1000 mg/L, respectively. The demulsifier also greatly decreased water content in oil phase and oil concentration in water phase for actual produced liquid from oil well. The demulsification mechanism was also investigated in terms of IFT and zeta potential.     

Molecular dynamics simulation of four typical surfactants at oil/water interface

In the present study, we have performed molecular dynamics simulations to describe the microscopic behaviors of the anionic, nonionic, zwitterion, and gemini surfactants at oil/water interface. The abilities of reducing the interfacial tension and forming the stable interfacial film of the four surfactants have been investigated through evaluating interfacial thickness, interface formation energy and radial distribution function. The results show that the four kinds of surfactants can form in stable oil/water interface of monolayer, and the gemini surfactant can form the more stable monolayer. The results of the above three parameters demonstrate that the gemini surfactant has the best simulation effect in the four surfactants. From the calculated interfacial tension values, the gemini surfactant possess the more powerful ability of reducing the interfacial tension than others, so it is more suitable to be used as the surfactant for flooding. In addition, the effects of different electric field intensities on surfactants were calculated, through the radial distribution function of the hydrophilic group in the surfactant and the oxygen atom in the water. We have found that the adding of the periodic electric field can significantly affect the diffusion behavior of the molecules, and nonionic surfactant has stronger demulsification capability than others.     

三元复合驱碱/表面活性剂/聚合物模拟原油乳状液稳定动力学特性

基于两相分离的乳状液稳定模型,研究了三元复合驱模拟原油乳状液稳定动力学特性;通过液膜强度和油水界面张力探讨了碱/表面活性剂/聚合物对模拟原油乳状液稳定动力学特性的影响机理。 结果表明,乳状液稳定模型可以很好的评价乳状液的稳定性,并得到乳状液的稳定动力学特性;碱浓度小于900 mg/L有利于乳状液的稳定,碱浓度大于900 mg/L不利于乳状液的稳定;表面活性剂和聚合物浓度的增加使得形成的模拟原油乳状液更加稳定;模拟原油乳状液的稳定作用主要是通过碱、表面活性剂降低油水界面张力并增加油水界面膜强度,聚合物通过提高界面膜强度实现的,三者存在协同效应。     

Study on Influencing Factors of Chemical Flooding for Heavy Oil

Alkali and alkali/surfactant displacing agents are designed for two kinds of heavy oil. Results of emulsifying capacity, dynamic interfacial tension (IFT) and water-wet core flooding tests show that, although alkaline/surfactant systems exhibit better capacity in emulsification and IFT reduction, oil recovery values of alkaline/surfactant flooding are lower than those of alkaline flooding. Glass-etched micromodel tests further demonstrate that, when alkaline solution penetrates into the oil phase, water streams break into ganglia coating oil film. Water ganglia may be entrapped by narrow throats, consequently presenting a water-oil alternating slug flow. Similar water ganglia also appears in alkaline/surfactant flooding, however, water channeling along the pore surface occurs subsequently, resulting in its relatively lower oil recovery.     

Synergistic effect of mixed anionic and cationic surfactant systems on the interfacial tension of crude oil-water and enhanced oil recovery

Surfactant based enhanced oil recovery (EOR) is an interesting area of research for several petroleum researchers. In the present work, individual and mixed systems of anionic and cationic surfactants consisting of sodium dodecyl sulphate (SDS) and cetyltrimethylammonium bromide (CTAB) in different molar ratios were tested for their synergistic effect on the crude oil-water interfacial tension (IFT) and enhanced oil recovery performance. The combination of these two surfactant systems showed a higher surface activity as compared to individual surfactants. The effect of mixed surfactant systems on the IFT and critical micellar concentration (CMC) is strongly depends on molar ratios of the two surfactant. Much lower CMC values were observed in case of mixed surfactant systems prepared at different molar ratios as compared to individual surfactant systems. The lowest CMC value was found when the molar concentration of SDS was higher than the CTAB. When the individual and mixed surfacant systems were tested for EOR performance through flooding experiments, higher ultimate oil recovery was obtained from mixed surfactant flooding compared to individual surfactants. Combination of SDS and CTAB or probably other anionic-cationic surfactants show synergism with substantial ability to reduce crude oil water IFT and can be a promising EOR method.     

Mechanism for viscoelastic emulsion displacing oil film – A numerical simulation approach

The reservoir characteristics and fluid property of Daqing reservoir were taken as the research platform. For simulating the emulsifying process in the reservoir, injecting different concentrations of emulsifier solution into the core after water flooding, the viscoelasticity of the emulsion was measured. According to the value of the emulsion viscoelasticity, the numerical model of emulsion displacing oil film was established. Elastic stress acting on the oil film was calculated when the emulsion migrates. The deformation and transportation of the oil film were analyzed at bearing the elastic stress. The results show that the emulsion has favorable viscoelasticity. When the emulsifier concentration is higher, the emulsion elasticity is favorably increased. The oil film can deform and transport forward by the elastic stress. The elastic stress increases as the emulsion elasticity increases.     

Foam, emulsion and wetting films stabilized by polyoxyalkylated diethylenetriamine (DETA) polymeric surfactants

This review explores three (A, B, C) polyoxyalkylated diethylenetriamine (DETA) polymeric surfactants belonging to the group of star-like polymers. They have a similar structure, differing only in the number of polymeric branches (4, 6 and 9 in the mentioned order). The differences in these surfactants' ability to stabilize foam, o/w/o and w/o/w emulsion and wetting films are evaluated by a number of methods summarized in Section 2. Results from the studies indicate that differences in polymeric surfactants' molecular structure affect the properties exhibited at air/water, oil/water and water/solid interfaces, such as the value of surface tension, interfacial tension, critical micelle concentration, degree of hydrophobicity of solid surface, etc. Foam, emulsion and wetting films stabilized by such surfactants also show different behavior regarding some specific parameters, such as critical electrolyte concentration, surfactant concentration for obtaining a stable film, film thickness value, etc. These observations give reasons to believe that model studies can support a comprehensive understanding of how the change in polymeric surfactant structure can impact thin liquid films properties. This may enable a targeted design of the macromolecular architecture depending on the polymeric surfactants application purpose.     

A novel formulation of the pickering emulsion stabilized with silica nanoparticles and its thermal resistance at high temperatures

Stabilization of emulsions with solid particles can be used in several fields of oil and gas industry because of their higher stability. Solid particles should be amphiphilic to be able to make Pickering emulsions. This goal is achieved by using surfactants at low concentrations. Oil-in-water (o/w) emulsions are usually stabilized by surfactant but show poor thermal stability. This problem limits their applications at high-temperature conditions. In this study, a novel formulation for o/w stabilized emulsion by using silica nanoparticles and the nonionic surfactant is investigated for the formulation of thermally stable Pickering emulsion. The experiments performed on this Pickering emulsion formula showed higher thermal stability than conventional emulsions. The optimum wettability was found for DME surfactant and silica nanoparticles, consequently, in that region; Pickering emulsion showed the highest stability. Rheological changes were evaluated versus variation in surfactant concentration, silica concentration and pH. Scanning electron microscopy images approved the existence of a rigid layer of nanoparticle at the oil-water interface. Finally, the results show this type of emulsion remains stable in harsh conditions and allows the system to reach its optimum rheology without adding any further additives.     

Demulsification of produced liquid from surfactant-polymer flooding

Treatment of the produced fluid obtained by surfactant-polymer (SP) flooding is difficult because of the stabilizing effects exhibited by surfactants and polymers on oil-in-water emulsions. For the produced fluid from Xinjiang oilfield, YH-1 (a mixture of 603 and YB-990) showed promising demulsification effects. When the dosage of YH-1 was 20?mg/L at 323?K, the dewatering efficiency reached no less than 72% even when both surfactant and polymer contcentrations were 1200?mg/L. Experimental results showed that YH-1 reduces the water content in crude oil to no more than 20%, which meets the commercial requirements before entering the electronic field. Demulsification performed by thermal-chemical and electric field treatments further reduced the water content in crude oil to less than 2.0%.     

Wetting in oil/water/surfactant systems

The behaviour of oils at aqueous interfaces is ubiquitous to many industrially and biologically relevant processes. In this review we consider modifications to the wetting properties of oils at the air/water, oil/water and solid/liquid interfaces in the presence of surfactants. First-order wetting transitions can be induced in a wide range of oils by varying the aqueous surfactant concentration, leading to the formation of mixed monolayers at the interface. In certain cases, these mixed monolayers display novel surface freezing behaviour, including the formation of unusual bilayer structures, which further modifies the properties of the interface. The effects of surfactant on line tension at the three-phase contact line and differences between the air/liquid and liquid/liquid interfaces are discussed.     

溶致液晶体系研究及其在三次采油中的应用

研究了石油磺酸盐/正戊醇/水的三元体系和石油磺酸盐/癸烷/正戊醇/水的拟三元体系相图中的液晶区域,揭示了不同组分对液晶区域大小的影响以及液晶的流变性和液晶的结构.在三次采油中,用六角状溶致液晶体系代替三元复合驱体系进行化学驱油,虽然驱油效率更高,但需要进一步降低液晶驱油体系的成本.     

What is the Criterion for Selecting Alkaline/Surfactaint/Polymer Flooding Formulation: Phase Behavior or Interfacial Tension

An experimental study on determination of alkaline, surfactant, polymer (ASP) flooding systems using natural mixed carboxylate was conducted to examine the decisive factor for ASP flooding, phase behavior or interfacial tension. The volume and color of middle phase liquid were observed, the transient interfacial tension at different salt and alkaline concentrations were measured and, finally, coreflood test in laboratory were made. The results showed the flooding system with larger volume and brown color of middle phase emulsion sometimes not to obtain better oil recovery efficiency. The primary and more important phenomenon affecting the oil recovery is a lower or ultralow minimum interfacial tension value at the crude oil/soluble phase interface.     

油田采出液中微量羧酸盐表面活性剂分析方法研究

油田采出液中化学剂浓度的检测是三元复合驱动态评价的重要指标之一。本文针对现场提出的对微量羧酸盐表面活性剂的检测问题,建立了一种用紫外分光光度法测定微量羧酸盐表面活性剂分析的新方法。该法简便、准确快速,线性范围宽,回收率在94.4-103.1%之间,相对标准偏差为1.38%。并根据油田生产的实际情况,探论了碱、聚合物、原油等干扰因素对测定的影响,结果满意。     

In Situ Treatment of Thermal RF Plasma Processed Nanopowders to Control their Agglomeration and Dispersability

Titanium carbonitride nanoparticles have been produced in an inductively coupled thermal plasma and subsequently modified using a surfactant that has been deposited in situ on their surface in-flight. The surfactant was injected in the reactor while the nanoparticles are still dispersed in the gas phase, allowing the coating of primary particles instead of the corresponding agglomerates. In contrast to naked TiCN nanoparticles, the surfactant coated particles could be readily dispersed in water with a short ultrasonic treatment and built up no large agglomerates as proved by Photon Correlation Spectroscopy measurements. The investigated surfactants seem, however, to undergo a chemical modification and/or a thermal degradation at the surface of the TiCN nanoparticles.     

Use of surfactants to remove water-based inks from plastic film: effect of calcium ion concentration and length of surfactant hydrophobe

Effective plastic film deinking could permit the reuse of recycled polymer to produce clear film, reduce solid waste for landfills, reduce raw material demand for polymer production, and aid process economics. In this study, the deinking of a commercial polyethylene film printed with water-based ink was studied using surfactants in the presence of hardness ions (calcium ions) at various pH levels. The electrostatic properties of ink particles in a washing bath were also investigated. Synthetic anionic surfactant or fatty acid soap in the presence of calcium ions at alkaline pH levels was found to be nearly as effective at deinking as cationic, nonionic, or amphoteric surfactants alone. However, adding calcium ions decreases the deinking effectiveness of cationic, nonionic, and amphoteric surfactants. Increasing the length of the ionic surfactant hydrophobe enhances deinking. Zeta potential measurements showed that water-based ink particles in water reach the point of zero charge (PZC) at a pH of about 3.6, above which ink particles are negatively charged, so cationic surfactant tends to adsorb better on the ink than anionic surfactant above the PZC in the absence of calcium. As the cationic surfactant concentration is varied between 0.005 and 25 mM, the zeta potential of the ink particles reverses from negative to positive owing to adsorption of cationic surfactant. For anionic surfactants, added calcium probably forms a bridge between the negatively charged ink and the negatively charged surfactant head groups, which synergizes adsorption of the surfactant and aids deinking. In contrast, calcium competes for adsorption sites with cationic and nonionic surfactants, which inhibits deinking. All the surfactants studied here disperse ink particles effectively in the washing bath above pH 3 except for the ethoxylated amine surfactant.     

Phase behavior and structure analysis of the middle mixed layer for ASP flooding system at low surfactant concentration

The phase behavior and interfacial tension of alkali/surfactant/polymer (ASP) flooding system and simulative crude oil were investigated, and the size distribution and structure analysis of the middle mixed layer (MML) were also studied by size analyzer and freeze-fracture TEM. It was found that there were some rules between the volume of MML and the concentration of each component, and the interfacial tension between MML and the oil phase or water phase could reach an ultra-low value. Especially, the freeze-fracture TEM micrographs of MML were firstly obtained, and the new viewpoint was put forward that there coexist the structures of micelle, microemulsions and emulsions in MML and the structure of microemulsion is dominant. This would make an important effect on the research of surfactant theory and ASP flooding mechanism.     

The influence of sodium ethene sulphonate comonomer on the film formation process of poly(vinyl acetate) dispersions

Various latex dispersions from vinyl acetate/sodium ethene sulphonate (sodium vinyl sulphonate) copolymers, stabilised by a constant amount of Hostapal BV, a surfactant with poly(ethylene oxide) groups, were investigated by a variety of solid and liquid state nuclear magnetic resonance methods. In order to investigate the influence of sodium ethene sulphonate on the film formation process, the serum and polymer were analysed separately. The stoichiometric monomer composition of the copolymer in the aqueous phase and in the hydrophobic particles was obtained. The ionic comonomer is enriched at the particle surface via its proximity to the applied surfactant by two-dimensional exchange NMR. For investigations of the film formation process, latex dispersions were prepared and dried to form spatially homogeneous films at different defined solid contents. Depending on the chemical composition of a chosen dispersion, NMR allows the investigation of the drying process of the water. The drying process is a function of the ionic strength of the dispersion and the hydrophilicity of the polymer. It is correlated to the drying mechanism of the water within the film. A not fully dried film contains external water outside the particles, water at ionic and non-ionic groups at surfactants in the polymer water interface and, additionally, water in the swollen and mobilised polymer. The distribution of water to these environments is markedly changed by the ionic comonomer, especially close to the end of the drying process.     

Effect of liquid paraffin on the stability of aqueous foam in the presence and absence of electrolytes

The foam stability of dodecyl diphenyl ether disulfonate solution with liquid paraffin droplets in the presence and absence of electrolytes was evaluated, and the stabilization mechanisms were deduced. The foam film is stabilized when the monovalent and divalent counterion concentration is lower than a critical value. However, the foam stability declined with the addition of trivalent counterions. There are two mechanisms we have speculated. Firstly, the counterions reduce the repulsive interaction between the polar groups of surfactants adsorbed at the air/water and oil/water interfaces in the pseudo-emulsion film. Secondly, comparing with the monovalent counterions, the multivalent counterions are not only able to interconnect head groups of adjacent ionic surfactant molecules which are adsorbed at the air/water or oil/water interface, but also to attract the couples of neighboring surfactant head groups adsorbed at the air/water and oil/water interfaces. The attractive interaction between both the interfaces promotes the emulsified droplets piercing the air/water interface.     

Interaction between polymer and anionic/nonionic surfactants and its mechanism of enhanced oil recovery

Various experimental methods were used to investigate interaction between polymer and anionic/nonionic surfactants and mechanisms of enhanced oil recovery by anionic/nonionic surfactants in the present paper. The complex surfactant molecules are adsorbed in the mixed micelles or aggregates formed by the hydrophobic association of hydrophobic groups of polymers, making the surfactant molecules at oil-water interface reduce and the value of interfacial tension between oil and water increase. A dense spatial network structure is formed by the interaction between the mixed aggregates and hydrophobic groups of the polymer molecular chains, making the hydrodynamic volume of the aggregates and the viscosity of the polymer solution increase. Because of the formation of the mixed adsorption layer at oil and water interface by synergistic effect, ultra-low interfacial tension (～2.0?×?10^?3 mN/m) can be achieved between the novel surfactant system and the oil samples in this paper. Because of hydrophobic interaction, wettability alteration of oil-wet surface was induced by the adsorption of the surfactant system on the solid surface. Moreover, the studied surfactant system had a certain degree of spontaneous emulsification ability (D50?=?25.04?µm) and was well emulsified with crude oil after the mechanical oscillation (D50?=?4.27?µm).     

Mechanistic study of nanoparticles–surfactant foam flow in etched glass micro-models

This study was conducted in order to identify the pore-level mechanisms controlling the nanoparticles–surfactant foams flow process and residual oil mobilization in etched glass micro-models. The dominant mechanism of foam propagation and residual oil mobilization in water-wet system was identified as lamellae division and emulsification of oil, respectively. There was inter-bubble trapping of oil and water, lamellae detaching and collapsing of SDS-foam in the presence of oil in water-wet system and in oil-wet system. The dominant mechanisms of nanoparticles–surfactant foam flow and residual oil mobilization in oil-wet system were the generation of pore spanning continuous gas foam. The identified mechanisms were independent of pore geometry. The SiO₂-SDS and Al₂O₃-SDS foams propagate successfully in water-wet and oil-wet systems; foam coalescence was prevented during film stretching due to the adsorption and accumulation of the nanoparticles at the gas–liquid interface of the foam, which increased the films’ interfacial viscoelasticity.