Capillary electrophoresis of methylmercury with injection by sample stacking

A procedure for separation and quantitation of methylmercury by capillary electrophoresis using sample stacking as the injection technique is presented. The CE conditions have been optimized in order to separate the methylmercury from the excess cysteine peak and to concentrate large volumes of sample obtaining a low detection limit. Under the proposed operational conditions, the detection limit (S/N = 3) was 12 ng g⁻ and the limit of quantitation (S/N = 10) was 20 ng g⁻¹ with a linear range of 20–100 ng g⁻¹ (as methylmercury in samples). The method was tested using different reference materials with a certified methylmercury content.     

Quantitative analysis of fluorimated ethylchloroformate derivatives of non-protein amino acids using positive and negative chemical ionization gas chromatography-mass spectometry

The GC-MS characterization of the ethylchloroformate derivatives of amino acids in an aqueous medium has been applied to non-protein amino acids. Derivatization of non-protein amino acids using ethylchloroformate, trifluoroethanol, and pyridine produced strong [M + 1]⁺ and [M - 1]⁻ ions in positive and negative chemical ionization (CI) modes, respectively. Twenty-one out of the twenty-three non-protein amino acids studied produced detectable ion chromatograms in both ionization modes when methane was used as the CI reagent gas. Mass spectra of these non-protein amino acid derivatives showed characteristic [M - 19]⁺, [M + 1]⁺, [M + 29]⁺, and [M + 41]⁺ peaks in the positive chemical ionization mode, and [M - 1]⁻, and [M + 35]⁻ peaks in the negative chemical ionization mode. The detection limits and the linear dynamic range of trifluorethanol ethylchloroformate derivatives of non-protein amino acids were studied using positive chemical ionization. The detection limits are mostly in the femtomole range.     

Improvement of extraction recovery for the monobutyltin species from sediment

An improvement of the extraction recovery of the MBT species from sediment has been achieved by using a more polar solvent, toluene, and tropolone as chelating agent. A recovery of 84.7 ± 6.3% from spiked sediment has been achieved, which is the highest recovery of MBT species from sediment so far reported using solvent extraction techniques. The relative detection limit for organotin compounds in general in sediment (2 g) is 0.5 ng g⁻¹ when gas chromatography with atomic emission spectrometric detection is used for the analysis. Relative standard deviations (%) for recovery of MBT, DBT and TBT in spiked sediment range from 2.5 to 6.3% (at 0.5 μg g⁻¹ level). The extraction solution also recovers satisfactorily 7 other commonly used organotin compounds. Analyses of selected environmental samples and the Reference Sediment PACS-1 are given.     

Determination of arsenic in gold by flow injection inductively coupled plasma mass spectrometry with matrix removal by reductive precipitation

Arsenic was determined in gold by flow injection hydride generation inductively coupled plasma-mass spectrometry following a batch mode reductive precipitation removal of the interfering gold matrix. A solution of potassium iodide, L-ascorbic acid, and hydrochloric acid was used as the reluctant. The recovery of gold by precipitation and filtration was 99 ± 3%. The detection limit for arsenic in gold was 55 ng g⁻¹ in the solid. The concentration of arsenic that was determined in the Royal Canadian Mint gold sample FAU-10 was 29.7 μg g⁻¹ in the solid; this value was indistinguishable, with 95% confidence, from values determined at the Royal Canadian Mint by graphite furnace atomic absorption spectrometry and by inductively coupled plasma-mass spectrometry. The standard deviation for four replicate determinations of the arsenic in FAU-10 was 0.972 μg g⁻¹ in the solid.     

Chemical ionization mass spectrometry of hydrofluorocarbons, hydrofluorocarbon ethers and perfluoroalkenes

Positive and negative chemical ionization (CI) mass spectrometry is studied for hydrofluorocarbons (HFCs), hydrofluorocarbon ethers (HFEs), and perfluoroalkenes (PFCs) using various kinds of reagent gas. While no quasi-molecular ion was observed under electron impact ionization for saturated MFCs, [M-F]⁺ is detected under CI conditions using methane as a reagent gas. Mechanisms for the generation of [M-F]⁺ are discussed. Furthermore, nitrogen monoxide can be used as a reagent gas to observe [M + NO]⁺ for many HFCs and HFEs. In negative mode chloroform is also available to generate [M + Cl]⁻ for HFCs and HFEs containing -CHF- groups.     

Unauthorised antibiotic treatments in beekeeping: Development and validation of a method to quantify and confirm tylosin residues in honey using liquid chromatography–tandem mass spectrometric detection

A liquid chromatographic–tandem mass spectrometric (HPLC-MS/MS) method is proposed for the identification and quantification of tylosin in honey. Sample treatment involves an extraction in a Tris buffer at pH 10.5, followed by a solid-phase clean up step on an Oasis HLB column. Roxithromycin was used as the internal standard. Chromatographic separation of tylosin and roxithromycin was performed on an XTerra MS C₁₈ column (100 mm × 2.1 mm i.d., 5 μm) using a gradient of aqueous 0.01 M ammonium acetate pH 3.5 and acetonitrile as the mobile phase, at a flow rate of 0.25 ml min⁻¹. The method was validated according to the guidelines laid down by the Commission Decision 2002/657/EC. Tylosin residues were confirmed by MS/MS experiments considering the appropriate identification points. All validation parameters such as Cc (lower than 3 ng g⁻¹), Ccβ (lower than 5 ng g⁻¹), recovery and precision were assessed on the basis of the “critical ion” (less intense ion permitting unambiguous identification of the analyte).     

Analytical procedures for improved trace element detection limits in polar ice from Arctic Canada using ICP-SMS

Analytical procedures have been developed for the reliable determination of 19 trace elements (Ag, Al, Ba, Bi, Cd, Co, Cr, Cu, Fe, Mn, Pb, Rb, Sb, Sc, Sr, Tl, U, V, Zn) in ice samples at pg g⁻¹ and fg g⁻¹ concentrations using ICP-sector field mass spectrometry (ICP-SMS). Concentrations of most elements in the high purity water and doubly distilled HNO₃ employed were distinctly lower than previously reported values. The accuracy of the results was carefully evaluated using the certified water reference material SLRS-4. Contributions of unwanted trace elements due to acidification of the ice samples (0.5% HNO₃) to the total element budget amounted to only 0.001 pg g⁻¹ for Bi, 0.34 pg g⁻¹ for Cr, 0.2 pg g⁻¹ for Fe, 0.004 pg g⁻¹ for Pb, 0.00015 pg g⁻¹ for U and 0.0025 pg g⁻¹ for V: compared to the concentrations of the metals in ice these are negligible. The use of a detergent (0.05%) in the rinsing solution (0.5% HNO₃), helped to reduce memory effects by 59–98%, depending on the element considered; this resulted in shorter washing times between samples (i.e. 1 min) and improved analysis time. Adopting strict clean room procedures, the detection limit for Pb (0.06 pg g⁻¹) is a factor of ten lower than the current state-of-the-art. Compared to previous studies, the improved LODs obtained here for other trace elements amount to 2× (Ag), 4× (Sb), 5× (Ba), 6× (Cu, Mn, U), 9× (Bi), 13× (Cd), 18× (Fe) and 21× (V). The developed analytical protocols were successfully applied to the determination of selected trace elements in age-dated ice samples from the Canadian High Arctic. The toxic trace element Tl (median: 0.16 pg g⁻¹; range: 0.03–1.32 pg g⁻¹) and the lithogenic reference element Sc (0.53 pg g⁻¹; 0.06–2.9 pg g⁻¹) have been determined in a polar ice core for the first time.     

Determination of long-lived radionuclides in concrete matrix by laser ablation inductively coupled plasma mass spectrometry

A laser ablation system using a Nd:YAG laser was coupled both to a quadrupole inductively coupled plasma (ICP) mass spectrometer and to a double-focusing sector field ICP mass spectrometer. Laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) was applied for the determination of long-lived radionuclides in a concrete matrix. The investigated samples were two laboratory standards with a concrete matrix, which we doped with different long-lived radionuclides (e.g. ⁹⁹Tc, ²³²Th, ²³³U, ²³⁷Np) from the ng g⁻¹ to μ g⁻¹ concentration range and an undoped concrete material (blank). Detection limits for long-lived radionuclides in the 10 ng g⁻¹ range are reached for LA-ICP-MS using the quadrupole mass spectrometer. With double-focusing sector field ICP-MS, the limits of detection are in general one order of magnitude lower and reach the sub ng g⁻¹ range for ²³³U and ²³⁷Np. A comparison of mass spectrometric results with those of neutron activation analysis on undoped concrete sample indicates that a semiquantitative determination of the concentrations of the minor and trace elements in the concrete matrix is possible with LA-ICP-MS without using a standard reference material.     

As, Cd, Cr, Ni and Pb pressurized liquid extraction with acetic acid from marine sediment and soil samples

Rapid leaching procedures by Pressurized Liquid Extraction (PLE) have been developed for As, Cd, Cr, Ni and Pb leaching from environmental matrices (marine sediment and soil samples). The Pressurized Liquid Extraction is completed after 16 min. The released elements by acetic acid Pressurized Liquid Extraction have been evaluated by inductively coupled plasma-optical emission spectrometry. The optimum multi-element leaching conditions when using 5.0 ml stainless steel extraction cells, were: acetic acid concentration 8.0 M, extraction temperature 100 °C, pressure 1500 psi, static time 5 min, flush solvent 60%, two extraction steps and 0.50 g of diatomaceous earth as dispersing agent (diatomaceous earth mass/sample mass ratio of 2). Results have showed that high acetic acid concentrations and high extraction temperatures increase the metal leaching efficiency. Limits of detection (between 0.12 and 0.5 μg g^− 1) and repeatability of the over-all procedure (around 6.0%) were assessed. Finally, accuracy was studied by analyzing PACS-2 (marine sediment), GBW-07409 (soil), IRANT-12-1-07 (cambisol soil) and IRANT-12-1-08 (luvisol soil) certified reference materials (CRMs). These certified reference materials offer certified concentrations ranges between 2.9 and 26.2 μg g^− 1 for As, from 0.068 to 2.85 μg g^− 1 for Cd, between 26.4 and 90.7 μg g^− 1 for Cr, from 9.3 to 40.0 μg g^− 1 for Ni and between 16.3 and 183.0 μg g^− 1 for Pb. Recoveries after analysis were between 95.7 and 105.1% for As, 96.2% for Cd, 95.2 and 100.6% for Cr, 95.7 and 103% for Ni and 94.2 and 105.5% for Pb.     

Optimisation of sample treatment for arsenic speciation in alga samples by focussed sonication and ultrafiltration

A procedure for arsenic species fractionation in alga samples (Sargassum fulvellum, Chlorella vulgaris, Hizikia fusiformis and Laminaria digitata) by extraction is described. Several parameters were tested in order to evaluate the extraction efficiency of the process: extraction medium, nature and concentration (tris(hydroxymethyl)aminomethane, phosphoric acid, deionised water and water/methanol mixtures), extraction time and physical treatment (magnetic stirring, ultrasonic bath and ultrasonic focussed probe). The extraction yield of arsenic under the different conditions was evaluated by determining the total arsenic content in the extracts by ICP-AES. Arsenic compounds were extracted in 5 mL of water by focussed sonication for 30 s and subsequent centrifugation at 14,000 × g for 10 min. The process was repeated three times. Extraction studies show that soluble arsenic compounds account for about 65% of total arsenic.

An ultrafiltration process was used as a clean-up method for chromatographic analysis, and also allowed us to determine the extracted arsenic fraction with a molecular weight lower than 10 kDa, which accounts for about 100% for all samples analysed.

Speciation studies were carried out by HPLC–ICP-AES. Arsenic species were separated on a Hamilton PRP-X100 column with 17 mM phosphate buffer at pH 5.5 and 1.0 mL min⁻¹ flow rate. The chromatographic method allowed us to separate the species As(III), As(V), MMA and DMA in less than 13 min, with detection limits of about 20 ng of arsenic per species, for a sample injection volume of 100 μL. The chromatographic analysis allowed us to identify As(V) in Hizikia (46 ± 2 μg g⁻¹), Sargassum (38 ± 2 μg g⁻¹) and Chlorella (9 ± 1 μg g⁻¹) samples. The species DMA was also found in Chlorella alga (13 ± 1 μg g⁻¹). However, in Laminaria alga only an unknown arsenic species was detected, which eluted in the dead volume.     

Analysis for chloroanisoles and chlorophenols in cork by stir bar sorptive extraction and gas chromatography–mass spectrometry

A complete methodology for the determination of chloroanisoles and chlorophenols in cork material is proposed. The determination is accomplished by means of a previous liquid–solid extraction followed by stir bar sorptive extraction (SBSE) coupled to gas chromatography–mass spectrometry (GC–MS). Two different liquid–solid extraction experiments were conducted and eight compounds considered (2,6-dichloroanisole, 2,4-dichloroanisole, 2,4,6-trichloroanisole, 2,4,6-trichlorophenol, 2,3,4,6-tetrachloroanisole, 2,3,4,6-tetrachlorophenol, pentachloroanisole and pentachlorophenol). From the results obtained we can conclude that high volume extraction extending extraction time up to 24 h is the best choice if we have to release compounds from the inner surfaces of cork stoppers. Recovery percentages ranged from 51% for pentachloroanisole to 81% for 2,4-dichloroanisole. This method allows the determination of an array of compounds involved in cork taint at very low levels from 1.2 ng g⁻¹ for 2,4,6-tricholoroanisole to 23.03 ng g⁻¹ for 2,3,4,6-tetrachlorophenol.     

Nickel determination in saline matrices by ICP-AES after sorption on Amberlite XAD-2 loaded with PAN

In the present paper, a solid phase extraction system for separation and preconcentration of nickel (ng g⁻¹) in saline matrices is proposed. It is based on the adsorption of nickel(II) ions onto an Amberlite XAD-2 resin loaded with 1-(2-pyridylazo)-2-naphthol (PAN) reagent. Parameters such as the pH effect on the nickel extraction, the effect of flow rate and sample volume on the extraction, the sorption capacity of the loaded resin, the nickel desorption from the resin and the analytical characteristics of the procedure were studied. The results demonstrate that nickel(II) ions, in the concentration range 0.10–275 μg l⁻¹, and pH 6.0–11.5, contained in a sample volume of 25–250 ml, can be extracted by using 1 g Amberlite XAD-2 resin loaded with PAN reagent. The adsorbed nickel was eluted from the resin by using 5 ml 1 M hydrochloric acid solution. The extractor system has a sorption capacity of 1.87 μmol nickel per g of Amberlite XAD-2 resin loaded with PAN. The precision of the method, evaluated as the R.S.D. obtained after analyzing a series of seven replicates, was 3.9% for nickel in a concentration of 0.20 μg ml⁻¹. The proposed procedure was used for nickel determination in alkaline salts of analytical grade and table salt, using an inductively coupled plasma atomic emission spectroscopy technique (ICP-AES). The standard addition technique was used and the recoveries obtained revealed that the proposed procedure shows good accuracy.     

Supported liquid membranes for the determination of vanillin in food samples with amperometric detection

A supported liquid membrane system has been developed for the extraction of vanillin from food samples. A porous PTFE membrane is impregnated with an organic solvent, which forms a barrier between two aqueous phases. The analyte is extracted from a donor phase into the hydrophobic membrane and then back extracted into a second aqueous solution, the acceptor. The determination (100–1400 μg ml⁻¹ vanillin) was performed using a PVC-graphite composite electrode versus Ag/AgCl/3MKCl at +0.850 V placed in a wall-jet flow cell as amperometric detector. The solid sample is directly placed in the membrane unit without any treatment, and the analyte was extracted from the sample, passes through the membrane and conduced to the flow cell by the acceptor stream. The limit of detection (3σ) was 44 μg ml⁻¹. The method was applied to the determination of vanillin (9–606 μg g⁻¹) in food samples.     

A rapid and selective LC method for simultaneous determination of cyclosporin a and its major metabolite (AM1) in human serum at room temperature

A simple and highly selective isocratic reverse-phase high performance liquid chromatography (RP-LC) method at room temperature is developed in order to determination of Cyclosporine A (CyA) and its major metabolite (AM1) in serum samples of kidney transplanted patients. The method uses a phenyl column stationary phase, acetonitrile–water–methanol 47:50:3 as mobile phase and 215 nm detector wavelength, at room temperature. The solid phase extraction procedure using cyano disposable extraction column was carried out to separtate the CyA and AM1 with recovery 99±6 and 98±10, respectively. A linear correlation was found at the range of 40–1000 ng ml⁻¹ for CyA and 25–500 ng ml⁻¹ for AM1. The average intra and inter-day variations were 5.03 and 7.89% for CyA, 5.92 and 8.12% for AM1, respectively. The detection limit of 20 ng ml⁻¹ was found for CyA and 12.5 ng ml⁻¹ for AM1. Also, the clinical application of the method using serum concentration against time profile from kidney transplantated patients is reported.     

Determination of estrogens in river water by gas chromatography-negative-ion chemical-ionization mass spectrometry.

A method for the determination of estrogens (17alpha-estradiol, 17beta-estradiol, estrone, ethynyl estradiol, and estriol) as pentafluorobenzyl-trimethylsilyl (PFB-TMS) derivatives by gas chromatography-mass spectrometry (GC-MS) with negative-ion chemical-ionization (NICI) is described. The NICI of all the derivatives produced an intense [M-PFB]- ion as the base peak. The reagent gas (methane) flow-rate and the ion source temperature were determined to be 2.0 ml/min and 240 degrees C, respectively, for the optimized NICI-selected ion monitoring (SIM) conditions. The sensitivities of the PFB-TMS derivatives in the NICI mode were 8.0-130 times higher than those of the PFB-TMS derivatives in electron ionization (EI) mode, and 12-25 times higher than those of all the TMS derivatives in the EI mode. This method was applied to the analysis of estrogens in river water using a solid-phase extraction as the sample preparation. The recoveries of the target chemicals from a river-water sample spiked with standards at 2 ng/l level were 85.8-126.5% (RSD, 6.2-13.0%). The methodical detection limits ranged from 0.10 to 0.28 ng/l.     

Comparison of AFS and ICP-MS detection coupled with gas chromatography for the determination of methylmercury in marine samples

Inductively coupled plasma mass spectrometry (ICP-MS) and atomic fluorescence spectrometry (AFS) coupled with gas chromatography (GC) have been evaluated as element specific detectors for the determination of methylmercury in marine samples. Detection limits for methylmercury chloride, obtained using ICP-MS and AFS, were 0.9 and 0.25 pg as Hg, respectively. Methylmercury was determined in marine tissue reference materials IAEA 142 and NIST 8044 mussel homogenate, and DOLT-2 dogfish liver by GC–AFS, with found values of 45±7, 26±4, and 671±41 ng g⁻¹, compared with certified values of 47±4, 28±2, and 693±53 ng g⁻¹. The analyses of IAEA 142 and NIST 8044 were repeated using GC–ICP-MS, with found values of 48±9 and 30±3 ng g⁻¹, respectively. Methylmercury was determined in real samples of ringed seal and beluga whale, with found values of 801±62 and 2830±113 ng g⁻¹, respectively.     

Investigation of equilibration and uncertainty contributions for the determination of inorganic mercury and methylmercury by isotope dilution inductively coupled plasma mass spectrometry

The mass fractions of Hg and methylmercury, in two certified reference materials, NIST2710 and DORM-2, have been determined by total and species-specific isotope dilution analysis (IDA), respectively, and uncertainty budgets for each analysis calculated. The mass fraction of Hg in NIST2710 was determined by ID using multicollector sector field inductively coupled plasma mass spectrometry (MC-SF-ICP-MS) whilst the mass fraction of methylmercury in DORM-2 was determined using HPLC coupled with quadrupole ICP-MS.

The extent of equilibration between the spike and the particulate bound mercury compounds was studied temporally by monitoring the ²⁰⁰Hg:¹⁹⁹Hg isotope amount ratio and by determining the total amount of Hg in the liquid phase. For the NIST2710 complete equilibration was only achieved when concentrated HNO₃ in combination with a microwave digestion was employed, and good agreement between the found (31.7±4.0 μg g⁻¹, expanded uncertainty k=2) and certified (32.6±1.8 μg g⁻¹) values was obtained. For DORM-2 complete equilibration of methylmercury between the liquid and solid phases was achieved when using 50:50 H₂O:CH₃OH (v/v) and 0.01% 2-mercaptoethanol as the solvent. Even though only 50% of the analyte was extracted into the liquid phase, complete equilibration was achieved, hence, the found methylmercury mass fraction (4.25±0.47 μg g⁻¹, expanded uncertainty k=2) was in good agreement with the certified value (4.47±0.32 μg g⁻¹).     

High Sensitivity Negative Ion GC-MS Method for Detection of Estrogens in Urine

A sensitive negative chemical ionization (NCI) gas-chromatography/mass spectrometry (GC/MS) method for the detection of estrogens is described. After hydrosis and clean-up by C₁₈ ODS solid phase extraction (SPE) cartridge, the extracts obtained were derivatized with heptafluorobutyric anhydride and analyzed in the negative ion mode by GC/MS. Stability of derivatives was good. Selected ion monitoring (SIM) mode was applied to increase the sensitivity and, when possible, the higher m/z ions were selected to improve identification. The detection limit of the HFB esters in NCI using SIM was below 10 femtograms.     

Effect of irradiation on anti-nutrients (total phenolics, tannins and phytate) in Brazilian beans

The Brazilian bean varieties Phaseolus vulgaris L. var. Carioca and Vigna unguiculata (L.) Walp var. Macaçar were irradiated with doses of 0.5, 1.0, 2.5, 5.0 and 10 kGy and subsequently stored at ambient temperature for 6 months. The anti-nutrients phenolic compounds, tannins and phytate were determined to be 0.48 mg g⁻¹ dry basis, 1.8 mg g⁻¹ dry basis and 13.5 μmol g⁻¹ dry basis in the raw non-irradiated Carioca beans and 0.30 mg g⁻¹ dry basis, 0.42 mg g⁻¹ dry basis and 7.5 μmol g⁻¹ dry basis in the raw non-irradiated Macaçar beans. After soaking and cooking a higher content of phenolic compounds and a lower phytate content was observed in both bean varieties. Tannin content was not affected by soaking and cooking of Carioca beans, but higher after soaking and cooking of Macaçar beans. Using radiation doses relevant for food did not effect the content of the anti-nutrients under investigation in both bean varieties.     

Determination of phenols in water by on-line solid-phase disk extraction and liquid chromatography with electrochemical detection

Poly(styrene-divinylbenzene) (PS-DVB) membrane extraction disks were used as sorbents for the on-line solid phase extraction of 13 phenols (nitro and chlorophenols) in river and tap waters. Determination was performed by liquid chromatography with electrochemical detection (LC-ED). An acetate buffer-acetonitrile-methanol mixture as mobile phase and amperometric detection at +1100 mV were used. High water volumes, up to 250 ml, can be preconcentrated without loss of phenols (recoveries between 80% and 100%) except for the more polar ones. Moreover, detection limits between 0.01 and 0.1 μg l⁻¹ in tap water and between 0.1 and 1.0 μg⁻¹ in river water were obtained. The method has been applied to the analysis of two river water samples.