Miscibility and transesterification in ternary blends of poly(ethylene naphthalate)/poly(trimethylene terephthalate)/poly(ether imide)

Miscibility and morphology of poly(ethylene 2,6-naphthalate)/poly(trimethylene terephthalate)/poly(ether imide) (PEN/PTT/PEI) blends were investigated by using a differential scanning calorimeter (DSC), optical microscopy (OM), wide-angle X-ray diffraction (WAXD), and proton nuclear magnetic resonance (¹H-NMR). In the ternary blends, OM and DSC results indicated immiscible properties for polyester-rich compositions of PEN/PTT/PEI blends, but all compositions of the ternary blends were phase homogeneous after heat treatment at 300 °C for more than 30 min. An amorphous blend with a single T _g was obtained in the final state, when samples were annealed at 300 °C. Experimental results from ¹H-NMR identified the production of PEN/PTT copolymers by so-called “transesterification”. The influence of transesterification on the behaviors of glass transition and crystallization was discussed in detail. Study results identified that a random copolymer promoted the miscibility of the ternary blends. The critical block lengths for both PEN and PTT hindered the formation of crystals in the ternary blends. Finally, the transesterification product of PEN/PTT blends, ENTT, was blended with PEI. The results for DSC and OM demonstrated the miscibility of the ENTT/PEI blends.     

Intimate blend of poly(ethylene terephthalate) and poly(ethylene 2,6‐naphthalate) via formation with and coalescence from their common inclusion compound with γ‐cyclodextrin

The experimental procedures to place poly(ethylene 2,6‐naphthalate) (PEN) guest molecules within γ‐cyclodextrin (γ‐CD) host molecules are described along with the subsequent verification of inclusion‐compound (IC) formation. In addition, the simultaneous complexing of PEN and poly(ethylene terephthalate) (PET) with γ‐CD to form their common IC is documented. Coalescence from their common γ‐CD IC generates an intimate blend of the PET and PEN polymers contained therein. Thermal analysis via differential scanning calorimetry reveals thermal behavior indicative of an intimate blend of PET and PEN. ¹H NMR analysis confirms that the intimate blending of PET and PEN achieved by coalescence from their common γ‐CD IC is not due to transesterification into a PET/PEN copolymer during thermal analysis. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 139–148, 2003     

Synthesis,physical characterization,and acetone sorption kinetics in random copolymers of poly(ethylene terephthalate) and poly(ethylene 2,6-naphthalate)

Random copolymers of poly(ethylene terephthalate) (PET) and poly(ethylene 2,6-naphthalate) (PEN) were synthesized by melt condensation. In a series of thin, solvent cast films of varying PEN content, acetone diffusivity and solubility were determined at 35°C and an acetone pressure of 5.4 cm Hg. The kinetics of acetone sorption in the copolymer films are well described by a Fickian model. Both solubility and diffusivity decrease with increasing PEN content. The acetone diffusion coefficient decreases 93% from PET to PET/85PEN, a copolymer in which 85 weight percent of the dimethyl terephthalate in PET has been replace by dimethyl naphthalate 2,6-dicarboxylate. The acetone solubility coefficient in the amorphous regions of the polymer decreases by approximately a factor of two over the same composition range. The glass/rubber transition temperatures of these materials rise monotonically with increasing PEN content. Copolymers containing 20 to 80 wt % PEN are amorphous. Samples with <20% or >80% PEN contain measurable levels of crystallinity. Estimated fractional free volume in the amorphous regions of these samples is lower in the copolymers than in either of the homopolymers. Relative free volume as probed by positron annihilation lifetime spectroscopy (PALS) decreases systematically with increasing PEN content. Acetone diffusion coefficients correlate well with PALS results. Infrared spectroscopy suggests an increase in the fraction of ethylene glycol units in the trans conformation in the amorphous phase as the concentration of PEN in the copolymer increases. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2981–3000, 1998     

Crystallization and morphology of poly(ethylene‐2,6‐naphthalene dicarboxylate) in the presence of nucleating agents

The crystallization and morphology of poly(ethylene‐2,6‐naphthalene dicarboxylate) (PEN) containing, as nucleating agents, a sodium salt of a copolymer of ethylene and acrylic acid or a sodium salt of a copolymer of ethylene and methacrylic acid, were investigated with differential scanning calorimetry, polarized optical microscopy, and small‐angle light scattering. The nucleating agents accelerated the crystallization rate at high temperatures by decreasing the surface free energy barrier hindering nucleation. Meanwhile, the nucleating agents with flexible chains could also improve the mobility of the PEN chains and increase the crystallization rate at low temperatures. Hedrites were observed when PEN was crystallized at high temperatures, whereas crystallization at low temperatures led to the formation of spherulites. Similar but smaller morphologies were obtained in the presence of nucleating agents. With nucleating agents, the spherulites formed at low temperatures were less perfect, although the optical properties of the spherulites were not influenced. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2387–2394, 2002     

Extraction-Photometric Determination of Niobium(V) by Reaction with Pyrocatechol and Thenoyltrifluoracetone

Abstract

The possibility of formation of mixed complex compound niobium(V)-pyrocatechol (PC)-thenoyltrifluoracetone (TTA) has been shown. Optimum conditions for the formation of such a compound have been found (7.5 M HCI, 0.3 MTTA, 0.4 MPC) and the molar ratio Nb (V):PC:TTA=1:2:2 has been established by the equilibrium shift method. The absorption spectrum of the chloroform extract of the Nb-PC-TTA compound has a maximum at 414 nm, ε= (7.7±0.2) × 10³. The influence of other ions on extraction-photometric determination of niobium (V) with PC and TTA is discussed.     

Influence of multiwall carbon nanotube on physical properties of poly(ethylene 2,6‐naphthalate) nanocomposites

Polymer nanocomposites consisting of multiwall carbon nanotube (MWCNT) and poly(ethylene 2,6‐naphthalate) (PEN) were prepared by a melt blending process in a twin‐screw extruder. The storage modulus (G′) and loss modulus (G″) of the PEN/MWCNT nanocomposites increased with increasing frequency, and this increment being more significant at low frequency. The terminal zone slope of G′ for the PEN/MWCNT nanocomposites decreased with increasing MWCNT content, and the nonterminal behavior of those was related to the dominant nanotube–nanotube interactions at higher MWCNT content, leading to the formation of the interconnected or network‐like structures of MWCNT in the polymer nanocomposites. The decrease in the slope of the plot of log G′ versus log G″ for the PEN/MWCNT nanocomposites with increasing MWCNT content suggested the changes in the microstructures of the polymer nanocomposites by incorporating MWCNT. The incorporation of very small quantity of MWCNT significantly improved the mechanical properties of the PEN/MWCNT nanocomposites. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1062–1071, 2006     

Morphology and thermal properties of a PC/PE blend with reactive compatibilization

Reactive compatibilization of immiscible polymers is becoming increasingly important and hence a representative study of a polycarbonate/high density polyethylene (PC/HDPE) system is the focus of this paper. A grafted copolymer PC‐graft‐ethylene‐co‐acrylic acid (PC‐graft‐EAA) was generated as a compatibilizer in situ during processing operation by ester and acid reaction between PC and ethylene‐acrylic acid (EAA) in the presence of the catalyst dibutyl tin oxide (DBTO). As the polyethylene (PE) matrix does not play any part during the synthesis of the copolymer and since PC and EAA are also immiscible, to simplify the system, the influence of this copolymer formation at the interface between PC and EAA on rheological properties, phase morphology, and crystallization behavior for EAA/PC binary blends was first studied. The equilibrium torque increased with the DBTO content increasing in EAA/PC blends on Haake torque rheometer, indicating the in situ formation of the graft copolymer. Scanning electron microscopy (SEM) studies of cryogenically fractured surfaces showed a significant change at the distribution and dispersion of the dispersed phase in the presence of DBTO, compared with the EAA/PC blend without the catalyst. Differential scanning calorimetry (DSC) studies suggested that the heat of fusion of the EAA phase in PC/EAA blends with or without DBTO reduced with the formation of the copolymer compared with pure EAA. Then morphological studies and crystallization behavior of the uncompatibilized and compatibilized blends of PC/PE were studied as functions of EAA phase concentration and DBTO content. Morphological observations in PC/PE blends also revealed that on increasing the EAA content or adding the catalyst DBTO, the number of microvoids was reduced and the interface was intensive as compared to the uncompatibilized PC/PE blends. Crystallization studies indicated that PE crystallized at its bulk crystallization temperature. The degree of crystallinity of PE phase in PC/PE/EAA blends was also reduced with the addition of EAA and DBTO compared to the uncompatibilized blends of PC/PE, indicating the decrease in the degree of crystallinity was more in the presence of PC‐graft‐EAA. Copyright © 2007 John Wiley & Sons, Ltd.     

PET/PEN共混物的相容性与酯交换反应

通过用1H-NMR对聚对苯二甲酸乙二酯(PET)与聚2,6-萘甲酸乙二酯(PEN)、PET/PEN共聚物的共混物酯交换反应的研究,测得了反应速率常数、反应活化能和诱导期.根据酯交换反应程度和不同反应温度下的诱导期探讨了酯交换反应与相容性的关系,认为PET与PEN的相容导致或增强了酯交换反应,即相容性是酯交换的必要条件;同时酯交换的发生又促进了PET与PEN的相容.酯交换和相容是聚酯共混物熔融时相互关联的两个过程.     

Characterization of copolymers of polycarbonate and polydimethylsiloxane by 2D chromatographic separation,MALDI-TOF mass spectrometry,and FTIR spectroscopy

Abstract

The structure and composition of polycarbonate polydimethylsiloxane copolymer (PC-co-PDMS) was investigated by applying various analytical approaches including chromatographic separation methods, spectrometric, and spectroscopic detection techniques. In particular, size exclusion chromatography (SEC) and liquid adsorption chromatography operating at different conditions (e.g. using gradient solvent systems) were used to achieve separations according to molar mass and functionality distribution. The coupling of both techniques resulted in fingerprint two-dimensional plots, which could be used to easily compare different copolymer batches. Matrix-assisted laser desorption/ionization-time-of-flight (MALDI-TOF) mass spectrometry was applied for structural investigations. The different ionization behavior of both comonomers, however, strongly limited the applicability of this technique. In contrast to that, Fourier-transform Infrared (FTIR) spectroscopy could be used to quantify the amount of PDMS in the copolymer at different points in the chromatogram. The resulting methodology was capable of distinguishing PC-co-PDMS copolymer from PC homopolymer chains present in the material.     

Copolymerization of Chloroprene with Methyl Methacrylate by the EtnAICI3.n (n=1, 1.5, 2)-Vanadium Compound System

Abstract

The copolymerization of chloroprene with methyl methacrylate was studied in the presence of Et_n A1C1_3-n (n=1, 1.5, 2)-vanadium compounds. Monomer reactivity ratios in various catalyst concentrations were compared with that of a usual radical initiator. The apparent monomer reactivity ratio changed with the concentration of alkylaluminum halide. In this polymerization, alternating copolymer could not be prepared by the ordinary catalyst concentration by which the alternating copolymerization of chloroprene with acrylonitrile was carried out. The addition of more than 10 mole % of the alkylaluminum halide based on two monomers was required to prepare the copolymer which had equimolar composition irrespective of the feed monomer ratio.

The configuration in the repeating unit of the copolymer was discussed by comparison with the NMR and IR spectra of the radical copolymer and the cyclic Diels-Alder adduct of chloroprene-methyl methacrylate. The high alternating tendency was clarified by ozonolysis of the copolymer which was prepared under the conditions which produced equimolar copolymer in various feed monomer ratios. The chloroprene unit of the copolymer was present in the 1, 4-trans structure in the copolymer prepared by the Et_n A1C1_3-n -vanadium compound system.     

Selective production of benzene and naphthalene from poly(butylene terephthalate) and poly(ethylene naphthalene-2,6-dicarboxylate) by pyrolysis in the presence of calcium hydroxide

Poly(butylene terephthalate) (PBT) and poly(ethylene naphthalene-2,6-dicarboxylate) (PEN) were pyrolysed in a fixed bed reactor in the presence of calcium hydroxide (Ca(OH)₂) in order to obtain benzene and naphthalene, respectively. In these experiments different ratios of polymer and Ca(OH)₂ were used. Also the temperature was varied in a range between 600 °C and 800 °C. It was found that the highest yield of benzene (67%) was obtained at a temperature of 700 °C and a molar Ca(OH)₂/PBT ratio of 10. The amount of carbon, fixed in the reactor residue after the experiment, was reduced from 56% for pure PBT to 38% under these conditions. Aromatic byproducts were reduced, as well, while the amount of 1,3-butadiene increased. Tetrahydrofuran was just formed under the influence of Ca(OH)₂.For PEN, the optimal conditions were found at a temperature of 600 °C and a molar Ca(OH)₂/PEN ratio of 5. A naphthalene yield of 80% from PEN was obtained. The rise of the naphthalene yield was caused by a more effective decomposition of the polyester by Ca(OH)₂, which led to the reduction of carbon in the reactor residue after the experiment from 59% for pure PEN to 10% under optimised conditions. The part of aromatic byproducts changed just slightly.     

Self‐assembled complexes of poly(acrylic acid) and poly(styrene)‐block‐poly(4‐vinyl pyridine)

Polymer complexes were prepared from high molecular weight poly(acrylic acid) (PAA) and poly(styrene)‐block‐poly(4‐vinyl pyridine) (PS‐b‐P4VP) in dimethyl formamide (DMF). The hydrogen bonding interactions, phase behavior, and morphology of the complexes were investigated using Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), dynamic light scattering (DLS), atomic force microscopy (AFM), and transmission electron microscopy (TEM). In this A‐b‐B/C type block copolymer/homopolymer system, P4VP block of the block copolymer has strong intermolecular interaction with PAA which led to the formation of nanostructured micelles at various PAA concentrations. The pure PS‐b‐P4VP block copolymer showed a cylindrical rodlike morphology. Spherical micelles were observed in the complexes and the size of the micelles increased with increasing PAA concentration. The micelles are composed of hydrogen‐bonded PAA/P4VP core and non‐bonded PS corona. Finally, a model was proposed to explain the microphase morphology of complex based on the experimental results obtained. The selective swelling of the PS‐b‐P4VP block copolymer by PAA resulted in the formation of different micelles. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1192–1202, 2009     

FTIR spectroscopic study on crystallization process of poly(ethylene-2,6-naphthalate)

In situ Fourier transform infrared (FTIR) measurements were carried out to elucidate conformation changes occurring during the isothermal melt crystallization of poly(ethylene-2,6-naphthalate) (PEN). Based on the band assignments for the components of the amorphous, α-crystal form, and β-crystal form of PEN in film samples, the in situ data was analyzed in terms of the amorphous- and crystal-trans conformations. It was observed at a higher isothermal crystallization temperature that the formation of amorphous-trans conformations precedes the growth of crystals. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 2741–2747, 1997     

Spectroscopic,thermal and X-ray crystal structure studies of some bis-(pyrazine-2-carboxylato) nickel(II) complexes

Three nickel(II) complexes [Ni(PC)₂(H₂O)₂], 1, [Ni(PC)₂(TU)₂], 2 and [Ni(PC)₂(ABI)₂]· 2(H₂O), 3, PC?=?pyrazine-2-carboxylate, TU?=?thiourea and ABI?=?2-aminobenzimidazole, were synthesized and characterized by elemental analysis, IR spectroscopy and thermal analysis. The complexes were also investigated by single crystal X-ray diffraction analysis. Structures of the monomeric complexes showed nickel(II) chelated to two PC ions from an oxygen atom of carboxylate ion and the adjacent hetero nitrogen atom. The three complexes were crystallized in a monoclinic system with P2 ₁ /c space group for 1, while 2 and 3 had C2/c space groups. The structure of 1 showed two coordinated water molecules occupying the trans positions of a slightly elongated octahedron. The structure of 2 consisted of two PC ions and two thiourea molecules in trans positions. The structure of 3 was different and showed a highly distorted octahedron with two ABI molecules chelated to the nickel ion in cis positions through their hetero nitrogen atoms. Two water molecules of crystallisation were shown in the structure of 3.     

Synthesis of Poly(Styrene)-block-poly(methacrylate)-block-poly(styrene) via Site Transformation Reaction

Abstract

Triblock copolymers with polystyrene outer blocks and an inner polymethacrylate block were synthesized by a site transformation reaction using anionic and cationic polymerization techniques. In order to obtain such ABA block copolymers, two synthetic routes have been applied. In the first case, different methacrylates (methyl methacrylate, 2-ethylhexyl methacrylate) were polymerized anionically with a bifunctional initiator to get poly(methacrylate) dianions later forming the inner block whereas in the second case poly(styrene)-block-poly(methacrylate) anions were synthesized by monofunctional initiation via sequential monomer addition. In a subsequent step, the living chain ends of the methacrylate dianions on one side, and the diblock copolymer anions on the other side, were functionalized with 1,4-bis(l-bromoethyl)benzene in order to obtain a potential bifunctional or monofunctional macroinitiator for the cationic polymerization of styrene. Then, styrene was polymerized cationically with the macroinitiator in the presence of SnCl₄ as coinitiator and _n Bu₄NBr as a common ion salt in CH₂Cl₂ at -15°C. Block formation was proven by SEC measurements, preparative SEC and NMR characterization.     

Transreactions in poly trimethylene terephthalate/bisphenol-A polycarbonate (PC) blends analysed by pressure-volume-temperature measurements

The effect of annealing on the miscibility and thermal properties of poly trimethylene terephthalate (PTT)/bisphenol-A polycarbonate (PC) blends was examined using pressure-volume-temperature (PVT) measurements. The PTT/PC blends were thermally annealed at 260 °C for different times to induce various extents of transesterification reactions between the two polymers. The non-annealed blends are immiscible and exhibit the thermal properties of the blend components. Upon annealing, the original semi-crystalline morphology transforms to an increasingly amorphous nature. PVT and WAXS analysis confirmed that the PTT/PC blends completely lost their crystallinity when annealed at 260 °C for a period of 120 min or longer, indicating the formation of random co-polyesters due to chemical transreactions between the PTT and PC. The further increase in the specific volume with annealing time also indicates that after reaching a completely amorphous co-polymer the transesterification continuous until a fully random copolymer is formed.     

Poly(crotonic acid-co-2-acrylamido-2-methyl-1-propanesulfonic acid)-metal complexes with copper(II), cobalt(II), and nickel(II): Synthesis, characterization and antimicrobial activity

Poly(crotonic acid-co-2-acrylamido-2-methyl-1-propanesulfonic acid) [P(CrA-co-AMPS)] (44.22:55.78) copolymer was prepared in N,N-dimethylformamide solution using the benzoyl peroxide (Bz₂O₂) as initiator. Cu(II), Ni(II) and Co(II) chelates of the copolymer were prepared and the formation constants of each complex were determined by the mole-ratio method using UV-vis spectroscopy. UV-vis studies showed that the complex formation tendency increased in the followed order: Cu(II) > Ni(II) > Co(II). The copolymer and its metal chelates were characterized by FTIR, TGA, X-ray diffraction and SEM analysis. Also, in vitro antimicrobial activity of the polymers were tested on various bacteria, and yeast.     

Biotinylated Poly(3-Hexylthiophene-co-3-Methanolthiophene): A Langmuir Monolayer-Forming Copolymer

Abstract

Copolymers of 3-substituted thiophenes have been synthesized by organosynthetic routes. The chemical synthesis of the copolymer was carried out by dehydrogenation of 3-hexylthiophene and 3-methanolthiophene. Attachment of biotin to the resulting copolymer, poly(3-hexylthiophene-co-3-methanolthiophene) [PMHT], is accomplished by room temperature esterification using N,N-dicyclohexylcarbodiimide (DCC) and 4-pyrrolidinopyridine as catalyst. The resulting copolymers have well-defined chemical and electronic structures and molecular weights. The biotinylated copolymer forms a stable monolayer at the air-water interface due to the polar groups along the polymer backbone.     

Effect of Structure of Functionalizing Molecules on the Inter‐Macromolecular Reactions and Blending of Poly(ethylene‐co‐propylene) (EPM) with Poly(6‐aminohexanoic Acid) (PA6)

Two different functionalizing systems, i.e., monohexadecyl maleate (= hexadecyl hydrogen (2Z)‐but‐2‐enedioate) in the presence of dicumyl peroxide (= bis(1‐methyl‐1‐phenylethyl) peroxide) or 4‐carboxybenzenesulfonazide (= 4‐(azidosulfonyl)benzoic acid), were used in distinct experiments to perform in a one‐step procedure the formation of a EPM–PA6 graft copolymer, necessary to obtain a compatibilized blend, from a molten mixture of ethylene–propylene copolymer (EPM) and polyamide 6 (PA6). The characterization of the graft polymer by selective solvent extraction of the blends and the subsequent IR and NMR analysis of the various fractions established the occurrence of functionalization reactions preferentially onto the polyolefin with both reagents. Also the formation in good yield of graft copolymers at the phases interface was observed. Moreover, the morphology and thermal characterizations of the blends by means of SEM and DSC analyses were used to evaluate the compatibilization extent in comparison with blends obtained by the conventional two‐step procedure or by the one‐step procedure with commercial maleic acid derivatives.     

Reaction-induced miscibility in blends comprised of bisphenol-A polycarbonate and poly(trimethylene terephthalate)

The inherent miscibility and effects of reaction-induced changes on the phase behaviour of blends of poly(trimethylene terephthalate) (PTT) with bisphenol-A polycarbonate (PC) were studied. The as-prepared (solution-cast) blends exhibited two well-spaced and separated glass transition temperatures (T_gs) and a heterogeneous phase-separated morphology, indicating an immiscible system. However, after annealing at high temperature (at 260 °C), the blends original two T_gs merged into one single T_g, and the annealed blends exhibited a homogeneous morphology, and turned from having a semicrystalline into having an amorphous nature upon extended annealing. The annealing-induced changes of phase behaviour in the blends were analyzed. The homogenization process of the blends upon heating is attributed to chemical transreactions between the PTT and PC chain segments, as evidenced with FT-IR characterization. The IR result showed a new aryl C-O vibration peak at 1,070 cm^–1 for the annealed blends, which is characteristic of an aromatic polyester structure formed from exchange reactions between PTT and PC. The transreactions between PTT and PC led to a random copolymer comprised of PC/PTT segments, which is believed to serve as a compatibilizer at the beginning stage of transreactions, but at later stage, the random copolymer became the main species of blends and turned to a homogeneous and amorphous phase.