双股燃气射流在充液室内扩展特性的实验研究

为了探索高温高压双股燃气射流在整装式液体工质中的扩展特性,设计了五级圆柱渐扩型观察室和圆柱型观察室,借助数字高速录像系统,观察了双股燃气射流在充液室中的扩展过程,对比了不同的观察室边界以及不同的参数条件对双股燃气射流扩展过程的影响。实验结果表明,圆柱渐扩型观察室结构更有助于改善气液的掺混特性,通过参数的合理匹配可以一定程度上控制双股燃气射流在三维充液室中的扩展过程。     

含能气体射流与液体相互作用的实验研究

为了研究整装式液体发射药的燃烧稳定性的控制方法,设计了点火喷射模拟装置及4种多级渐扩型观察室,利用数字高速摄像系统,观察含能气体射流在液体模拟工质中的扩展过程,并对实验中出现的喷孔壅塞现象进行了分析.结果表明:射流在渐扩型结构中扩展稳定,喷射压力、喷孔直径和渐扩结构对射流扩展形态和气液掺混过程有显著影响,通过合理调整这些参数,可以实现对射流扩展过程的有效控制;喷孔壅塞时射流扩展形态非对称,影响气液掺混,不利于控制射流的稳定性.     

圆柱形充液室中4股贴壁燃气射流扩展特性的实验研究

为了探索高温高压周向均布4股贴壁燃气射流在受限空间中的扩展特性,设计了贴壁燃气射流在圆柱形充液室内扩展的实验装置,借助数字高速录像系统,观察了4股贴壁燃气射流在充液室中的扩展过程,发现由Kelvin-Helmholtz不稳定性引起的表面不规则一直存在于整个射流扩展过程;通过处理拍摄记录的射流扩展序列图,获得不同时刻射流扩展的轴向和径向位移; 对比了不同破膜喷射压力和喷孔结构参数对4股贴壁燃气射流扩展过程的影响。实验结果表明:喷孔面积越大,贴壁射流初期轴向扩展速度越大,但由于径向扩展达到交汇的时间较早,湍流掺混和干涉强烈,衰减也越快;破膜喷射压力越高,射流径向扩展到达交汇的时间越短; 破膜喷射压力从12 MPa升高到20 MPa,射流轴向扩展速度大幅增加,气液湍流掺混效应增强。     

等离子射流与渐扩边界中液体工质相互作用特性的模拟实验

为了探索整装式液体工质电热化学炮中药室边界形状对燃烧控制的影响,采用数字高速录像系统对等离子体射流在液体工质中的扩展过程进行了测试,研究了不同放电电压、不同喷嘴直径、不同渐扩边界结构下等离子射流与液体工质的相互作用特性.获得了等离子射流在液体工质中扩展形态的时间序列图,处理出不同工况下Taylor空腔扩展的轴向位移与时...     

固体火箭燃气射流驱动液柱过程的CFD分析

固体火箭燃气射流驱动液柱过程会产生一个复杂的非稳态多相流场,为了研究液柱对固体火箭发动机工作过程中射流流场的降温效果,并揭示燃气冲击液柱的流动演化和气水之间的相互作用,利用FLUENT软件中耦合了液态水汽化方程的VOF多相流计算模型对燃气与液柱之间的耦合流动及相变过程进行了数值模拟,并与无液柱情况下射流流场的计算结果进行了对比分析。计算结果表明,当有液柱平衡体时射流流场中的压力、温度、速度波动幅度均减小,减弱了射流流场中的湍流脉动强度;液柱与燃气之间的汽化以及液柱的阻碍作用减小了射流流场的轴向发展位移,尾管后的完全发展射流流场核心区域内的压力峰值降低了0.9 MPa,温度峰值降低了503 K,速度峰值降低了291 m/s,验证了实验中液柱对燃气射流流场的降温效果。     

高速液体受限射流扩展形态研究

采用一种火药燃烧驱动液体喷射的新装置及其测试系统，研究受限空间中高速惰性液体射流的扩展结构。观察了环境反压、液体粘性、喷嘴结构等参量对射流扩展形态的影响，分析了射流雾化机理。研究结果对改进燃烧室设计及控制燃烧稳定性有一定的指导意义。     

火箭燃气射流冲击埸的实验研究

本文介绍火箭燃气射流冲击场的实验研究方法和结果,采用大口径长程莫阿偏折仪获得了自由射流和射流冲击场的莫阿偏折图,定量得到马赫盘位置、边界、斜激波等近场结构值,并与风洞冷射流模拟和数值模拟结果进行比较。     

火箭燃气射流冲击埸的实验研究

本文介绍火箭燃气射流冲击场的实验研究方法和结果,采用大口径长程莫阿偏折仪获得了自由射流和射流冲击场的莫阿偏折图,定量得到马赫盘位置、边界、斜激波等近场结构值,并与风洞冷射流模拟和数值模拟结果进行比较。     

轻型火箭发射噪声场的分布特性

为了解小火箭发射噪声特性及其在喷口外围的声压场分布规律,针对燃气射流产生噪声问题进行了实验研究和数值计算。讨论了超声速射流噪声的3个主要成分(湍流混合噪声、啸音和宽带激波相关噪声)及相关特点,指出它们产生的根本原因是湍流射流的速度扰动。通过分析不同实验测点的射流噪声声压级峰值,得到了燃气射流噪声在轴向和径向上的分布规律,即随着离喷口距离的增大,轴向噪声的衰减程度大于径向。在实验基础上,利用大涡模拟与FW-H(Ffowcs Williams-Hawkings)声学比拟相结合的方法对燃气射流噪声的声学特性进行计算。结果表明,此方法获得的计算结果与实验结果吻合较好,可为进一步研究射流噪声控制提供参考。     

圆环旋转黏性液体射流空间不稳定性研究

利用线性稳定性理论, 进行了液体黏性对不同旋转强度下圆环旋转液体射流 空间不稳定性影响的研究. 在推导出的三维扰动下具有固体涡核型旋转速度分布的圆环旋转 黏性液体射流色散方程的基础上, 针对中低速射流, 进行了类反对称模式与类对称模式下圆 环旋转黏性液体射流的空间不稳定性分析. 研究结果表明, 对于旋转强度较大的圆环旋转液 体射流, 液体黏性的增加, 不利于射流的破碎; 随着液体黏性的增加, 射流的特征频率和最 不稳定波数减小. 然而, 对于旋转强度较小的圆环旋转液体射流, 液体黏性的增加, 有利于 射流的破碎; 随着液体黏性的增加, 类反对称模式下射流特征频率先减小后增大, 类对称模 式下射流特征频率增大; 随着液体黏性的增加, 类反对称模式下射流最不稳定波数先减小后 增大, 类对称模式下射流最不稳定波数增大.     

Study on the influences of interaction behaviors between multiple combustion-gas jets on expansion characteristics of Taylor cavities

The purpose of this study is to investigate means of controlling the interior ballistic stability of a bulk-loaded propellant gun(BLPG).Experiments on the interaction of twin combustion gas jets and liquid medium in a cylindrical stepped-wall combustion chamber are conducted in detail to obtain time series processes of jet expansion,and a numerical simulation under the same working conditions is also conducted to verify the reliability of the numerical method by comparing numerical results and experimental results.From this,numerical simulations on mutual interference and expansion characteristics of multiple combustion gas jets(four,six,and eight jets) in liquid medium are carried out,and the distribution characteristic of pressure,velocity,temperature,and evolutionary processes of Taylor cavities and streamlines of jet flow Held are obtained in detail.The results of numerical simulations show that when different numbers of combustion gas jets expand in liquid medium,there are two different types of vortices in the jet flow field,including corner vortices of liquid phase near the step and backflow vortices of gas phase within Taylor cavities.Because of these two types of vortices,the radial expansion characteristic of the jets is increased,while changing numbers of combustion gas jets can restrain Kelvin-Helmholtz instability to a certain degree in jet expansion processes,which can at last realize the goal of controlling the interior ballistic stability of a BLPG.The optimum method for both suppressing Kelvin-Helmholtz instability and promoting radial expansion of Taylor cavities can be determined by analyzing the change of characteristic parameters in a jet flow field.     

Study on Expansion Characteristic of Twin Combustion Gas Jets in Five-Stage Cylindrical Stepped-wall Observation Chamber

The five-stage cylindrical stepped-wall observation chamber is designed to investigate the method of controlling the interior ballistic stability in bulk-loaded propellant guns. The expansion and mixing process of twin combustion gas jets in liquid is studied by means of high speed photographic system. The influence of multiple parameters on jet expansion shape is discussed. Based on the experiment, the three-dimensional mathematics model is established to simulate the expansion process of twin gas jets in liquid. The pressure, density, temperature, velocity contours and evolutionary process of vortices are obtained. Results show that vortices behind the corner of the steps are formed due to the inducing effect of steps. The jets can expand along the axial and radial direction simultaneously, weakening the Kelvin-Helmholtz instability. The numerical simulation results of axial expansion displacement are in good agreement with the experimental data.     

Producing ultra-high-speed nitrogen jets by arc heating in a low-pressure chamber

Pure nitrogen gas was heated with direct current arc, at input powers from several hundred W to over 5 k W, and then injected through a nozzle into a chamber at 1 or 10 Pa pressure, with the purpose of accelerating the gas to very high speed around 7 km/s. Various structures of the arc generator and gas expansion nozzle were examined. Results show that bypass exhausting of the boundary layer before it enters the nozzle divergent section can greatly increase flow speed of the jet, thus it might be possible to use nitrogen as a working gas in high speed gas dynamic test facilities.att     

A ballistic compressor-based experiment for the visualization of liquid propellant jet combustion above 100 MPa

 This paper describes the components and operation of an experimental setup for the visualization of liquid propellant (LP) jet combustion at pressures above 100 MPa. The apparatus consists of an in-line ballistic compressor and LP injector. The ballistic compressor, based on a modified 76 mm gun, provides high-pressure (ca. 55 MPa) clear hot gas for the jet ignition. A piston (projectile) is fired toward a test chamber beyond the barrel’s end, and its rebound is arrested in a transition section that seals the test chamber to the barrel. The LP jet is injected once the piston is restrained, and combustion of the jet further elevates the pressure. At a preset pressure, a disc in the piston ruptures and the combustion gas vents sonically into the barrel. If a monopropellant is used, the jet injection-combustion process then resembles liquid rocket combustion but at very high pressures (ca. 140 MPa). This paper discusses the ballistics of the compression and compares experimental results to those predicted by a numerical model of the apparatus. Experimentally, a pressure of 70 MPa was achieved upon a 12.5 volumetric compression factor by firing a 10 kg piston into 1.04 MPa argon using a charge of 75 g of small-grain M1 propellant. Received: 16 December 1996/Accepted: 15 July 1997     

同轴气流式液体射流分裂液滴粒径研究

针对同轴气流式液体射流分裂液滴粒径预测模型缺乏的现状,结合射流线性稳定性理论,建立了基于临界模数的同轴气流式黏性液体射流分裂液滴粒径表达式,在此基础上,分别研究了气流旋拧(气流同时存在轴向和周向运动)及流体物性(气体可压缩性、液体黏性、气液密度比和表面张力)对液滴粒径的影响规律.研究发现:周围气流轴向引射作用和同轴旋转...     

Nonlinear instability of an annular liquid sheet exposed to gas flow

Nonlinear instability and breakup of an annular liquid sheet has been modeled in this paper. The liquid sheet is considered to move axially and is exposed to co-flowing inner and outer gas streams. Also, the effect of outer gas swirl on sheet breakup has been studied. In the developed model a perturbation expansion method has been used with the initial magnitude of the disturbance as the perturbation parameter. This is a comprehensive model in that other geometries of planar sheet and a coaxial jet can be obtained as limiting cases of very large inner radius and inner radius equal to zero, respectively. In this temporal analysis, the effect of liquid Weber number, initial disturbance amplitude, inner gas-to-liquid velocity ratio, outer gas-to-liquid velocity ratio and outer gas swirl strength on the breakup time is investigated. The model is validated by comparison with earlier analytical studies for the limiting case of a planar sheet as well as with experimental data of sheet breakup length available in literature. It is shown that the linear theory cannot predict breakup of an annular sheet and the developed nonlinear model is necessary to accurately determine the breakup length. In the limiting case of a coaxial jet, results show that gas swirl destabilizes the jet, makes helical modes dominant compared to the axisymmetric mode and decreases jet breakup length. These results contradict earlier linear analyses and agree with experimental observations. For an annular sheet, it is found that gas flow hastens the sheet breakup process and shorter breakup lengths are obtained by increasing the inner and the outer gas velocity. Axially moving inner gas stream is more effective in disintegrating the annular sheet compared to axially moving outer gas stream. When both gas streams are moving axially, the liquid sheet breakup is quicker compared to that with any one gas stream. In the absence of outer gas swirl, the axisymmetric mode is the dominant instability mode. However, when outer gas flow has a swirl component higher helical modes become dominant. With increasing outer gas swirl strength, the maximum disturbance growth rate increases and the most unstable circumferential wave number increases resulting in a highly asymmetric sheet breakup with shorter breakup lengths and thinner ligaments.     

Study on three-dimensional expansion characteristics of four wall combustion-gas jets in confined liquid space

To explore further the launch mechanism of the new underwater launching technology proposed in this paper, the expansion characteristics of four wall combustion-gas jets in confined liquid space must be studied firstly. The experimental device is designed, and the high-speed digi-tal photographic system is adopted to obtain the expansion sequence processes of Taylor cavities formed by the four wall jets. Meanwhile, the influence of the injection pres-sure on the axial expansion property of the four wall jets is discussed. Based on the experiments, a three-dimensional unsteady mathematical model is established to simulate the turbulent flow process of the four wall jets expanding in liquid, and the temporal and spatial distribution laws of phase, pressure, temperature, and velocity and the evolution rules of vortices are illustrated in detail. Results show that, accompanied by the jets expanding downstream, the four wall combustion-gas jets get close to each other and achieve convergence eventually under induction of the interference effect between multiple jets. Meanwhile, the heads of the Taylor cavities separate from the observation chamber wall and offset to the central axis of the observation chamber with time going on. The numerical simulation results of the four wall combustion-gas jets coincide well with the experimental data.